Tait T800 - 22 - 0x00, T800 - 22 - 0x14, T800 - 22 - 0x10, T800 - 22 - 0x12, T800 - 22 - 0x15 Reference Manual

T800 Series

II

Conventional Equipment

Reference

Guide

M800RACK-00-100

M800RACK-00-100

Copyright TEL 30/8/99

Index

Section 1: Introduction

Guide to the Conventional T800 Equipment Questionnaire
Conventional T800 Equipment Questionnaire
Order Number System
Rack and Function Cross-Reference Chart

Rack Components Weights
Section 2: Rack Configurations
Section 3: Rack Power Supply Options
Section 4: Guide Assemblies
Section 5: Rack Backplanes
Section 6: Personality Boards
Section 7: Ancillary Modules
Section 8: Modules

T800 Series

II

Conventional Equipment

Reference Guide

Introduction

M800RACK-00-100 Section 1

Copyright TEL 30/8/99

T800 Conventional Equipment

This publication contains relevant reference information for Tait’s T800 Conventional
product range. It will be updated as equipment is modified or new features are
introduced.

It is intended to show only standard options. There is provision to ‘mix & match’ up to
seven modules in a rack to produce combinations for customised solutions.

Tait System Solutions are open-ended.

As well as information about the equipment there is also an order form and detailed
instructions on how to fill in the order form.

If you cannot find a solution,

Please contact RSD Custom Solutions.

Contact Details

Chris Quinlivan Conventional Systems Manager
Alex Brunton Systems Consultant
Alana Mehrtens Technical Illustrator

535 Wairakei Rd
PO Box 1645
Christchurch
New Zealand

Telephone: (64) (3) 3583399
Facsimile: (64) (3) 358 2825
E-mail: [e-mail]

M800RACK-00-100 Section 1

Copyright TEL 30/8/99

Document Control

The initial release of this guide will be a hard copy delivered to Customer Service
Organisations and other relevant people within the Tait organisation.

In the interests of imp roving the performance, re liability or servicing of the
equipment, Tait Electronics Limited reserve the right to update the equipment or this
document or both without prior notice.

The Master copy will be available on the Tait Electro nics Ltd Customer Service web
site.

Changes will be notified to all document holders who will be responsible for updating
these changes from the web site.

T800questV6.doc : Issued 25 Aug 1999 Page 1 of 3

Guide and Purpose of Filling out Conventional T800 Equipment

Questionnaire

The purpose of this questionnaire is to assist the staff of RSD to get as much
information as possible from you at the start of your enquires or order request
for equipment that is to be SET-UP BY RSD. The accurate completion of this form
will speed up processing time and ensure delivery of the correct equipment.

PART 01. (WHAT IS REQUIRED)

This is to immediately identify the quantity and what sort of configuration or equipment
is required.

PART 02. (FREQUENCY BAND REQUIRED

This is to indicate which frequency band the equipment is required to operate in. It also
gives the equipment type required.( for Series I the last four digits are not needed). In
some cases there will be a need for Transmitter and Receiver to be in different bands; this
will not affect the Rackframe required.

ENSURE EQUIPMENT STATED IS TYPE APPROVED FOR COUNTRY OF USE.

PART 03. (DO YOU KNOW WHAT IS REQUIRED)

The completion of this section in full is not always essential but the more information
you provide will assist the Technician in correctly configuring the Rackframe to your
requirements.

SPEAKER PANELS ARE FITTED AS STANDARD WHERE APPROPIATE

In the Rackframe line for part number you may put the code for the configuration
required, these codes can be found in the T800 Series II Conventional Equipment
Reference Guide, Section 1. If you do not have an RSD code, you may enter either the
high level T number, if known. These are also in the Reference Guide, Section 2, or enter
“do not know” and leave the selection of Rackframe to RSD who will select the
appropriate configured Rackframe to meet your requirements, based on the rest of the
information provided in this section.

T800questV6.doc : Issued 25 Aug 1999 Page 2 of 3

For the rest of the requirements you may tick the appropriate YES box for the module
that you would like to be fitted into the Rackframe, remembering there is only
sufficient room to fit 7 x 60mm modules. Doing this will help RSD ensure that
if a Rackframe has been mentioned it can support your requirements. If no standard
Rackframe exists that will fulfil your needs, then RSD will engineer a configuration to
satisfy your requirements.

PART 04 (EQUIPMENT TYPE REQUIRED)

This is to indicate the preferred type of equipment you require, remembering that
eventually all types will be Series II. Ensure type ordered are Type Approved for Country
of use.

PART 05 (DO YOU KNOW THE FREQUENCIES)

This information can be helpful as sometimes the auxiliary equipment can be frequency
dependant, ie; Duplexer/Splitters, etc..

PART 06 (AUXILLIARY EQUIPMENT)

The information provided in this section ensures that the auxiliary equipment asked for is
appropriate for the frequency band that the rest of the equipment is to operate in.

PART 07 (ANCILLIARY EQUIPMENT)

This section is to advise RSD of the maintenance support equipment required.

PART 08 (BRIEF DESCRIPTION)

This section is to enable you to give RSD a quick operational requirement and provide
sketches if deemed necessary on the information sheet provided.

PART 09 (ADDITIONAL COMMENTS)

This section is to allow you to provide any extra information you think RSD will require.

T800questV6.doc : Issued 25 Aug 1999 Page 3 of 3

PART 10

This is to inform RSD of your required delivery DATE .

PART 11 (TRANSMITTER/EXCITER PARAMETERS)

This section is to allow you to inform RSD of operational parameters for the equipment.

By ticking the STANDARD box you are indicating that all parameters required are as
stated in the Set-up procedure in the appropriate equipment manual, and the
frequency/frequencies required are as stated in PART 05. If no frequencies are stated in
Part 05 then the equipment is to be Set-up on TEST frequencies.

By ticking the CUSTOMISED box you are indicating special requirements are needed.
You must then fill in all the required details in the boxes below to allow RSD to set-up
the equipment to those specifications and options, and to supply any other information
that may be required by RSD.

PART 12 (RECEIVER PARAMETERS)

Same as above.

T800temp.V11.doc : Issued 09 Sept 1999 Page 1 of 4

This form has been devised to assist in clearly i denti fying the Product required, and its
operational parameters i f being BUILT and TESTED by RSD.

DO YOU REQUIRE RACKS and MODULES? DO YOU REQUIRE MODULES ONLY?

(Please continue on this page) (RSD to Set-up, Please go to PART 04)

PART 01. WHAT IS REQUIRED?

Base Station Portable Slimline To Operate as a Repeater Yes No

TOTAL QUANTITY REQUIRED :-

PART 02.

FREQUENCY BAND REQUI RED ?

66- 88Mhz

(T82n-xx-xxxx)

220-244Mhz

(T86n-xx-xxxx)

440-480Mhz

(T85n-xx-xxxx)

136-156Mhz

T83n-xx-xxxx)

243-270Mhz

(T86n-xx-xxxx)

480-520Mhz

(T85n-xx-xxxx)

148-174Mhz

(T83n-xx-xxxx)

330-380Mhz

(T87n-xx-xxxx)

800-880Mhz

(T88n-xx-xxxx)

174-225Mhz

(T37n-xx )

400-440Mhz

(T85n-xx-xxxx)

870-960Mhz

(T88n-xx-xxxx)

ARE REQUIRED MODULES TYPE APPROVED, COUNTRY OF USE :-
PART 03.

DO YOU KNOW WHAT IS REQUIRED PER RACK?

Description Option Required Qty Part Number

Rackframe

Receiver

Transmitter

Exciter

50 WattsPower Amplifier

70 / 100 Watt s

AC for Volts

External 13.8V Supply

Power Supply

Battery

Converter 12/12, 24/12, 48/12

Circuit Breaker 10Amp, 20Amp or 30Amp

Alarm Unit

Monitor Unit

Tone Remote

Combiner 200W

Hi Stability Osc

Channel Panel 10 Channel / 100 Channel

Cooling Fan Single or Double

Relay-50 W Max

Duplexer Tx/Rx Frequencies required

Duplexer Cradle (T800-42-0001)

Blank Panel (316-06615-00)

Speaker Panel Single/ selectable

CONVENTIONAL T800 EQUIPMENT

Customer Information: Date:

Customer / C.S.O
From:
Purchase Order Number:
RSD Quote Reference:
RSD Staff Responsible:

T800temp.V11.doc : Issued 09 Sept 1999 Page 2 of 4

PART 04. EQUIPMENT TYPE REQUIRED :- SERIES I SERIES II

PART 05. DO YOU KNOW THE FREQUENCIES AT THIS TIME?

No To be advised Attached

Yes

Tx MHz CTCSS Hz

Rx MHz CTCSS Hz

Channel Panel Eprom Info To be advised Attached

PART 06.

AUXILLIARY EQUIPMENT :-

Description OPTION REQUIRED Qty Part Number

For Freq:- Mhz

Power Monitor Kit

Automatic

Changeover

Unit

Installation Kit

PART 07. ANCILLIARY EQUIPMENT :-

Description Qty Part Number

Cabinet

Microphone

Programming Software

Module Extender with 2 D Ranges(standard)

Module Extender with 11 way D Range(QS)

Service Manuals

PART 08.
BRIEF DESCRIPTION : (Diagram / Info rmat i on Sheet Attached?) Yes No

PART 09.
ADDITIONAL COMMENTS :-

PART 10.

DATE REQUIRED

Purchase Order Number:

T800temp.V11.doc : Issued 09 Sept 1999 Page 3 of 4

PART 11.
TRANSMITTER/EXCITER PARAMETERS :- STANDARD CUSTOMISED

(As Manual) (Identify Requirements)

Channel Spacing : C.T.C.S.S. :

12.5 kHz No

20.0 kHz Yes

25.0 kHz Single

Other kHz (Freq Hz)

Frequency Stability : (VHF) 2.5 ppm Multiple

1.5 ppm (Pattern Required)
(UHF) 1.0 ppm Tx Time Out :
External Reference Disabled

Transmitter Power : Enabled

25 Watts (Max Time 5 mins) Duration Mins
50 Watts Tx Tail Time :

(For 800MHz Max 70W) 70 Watts Disabled

100 Watts Enabled

Other Watts (Max Time 5 secs) Duration Secs

Number of Channels : Audio Response :

Single Pre-emphasised

(Freq MHz) Flat

Multiple Special Modifications

(Pattern Required) No

Yes

Line Level : dBm Refer to Part 08

PART 12.
RECEIVER PARAMETERS :- STANDARD CUSTOMISED

(As Manual) (Identify Requirements)

Channel Spacing : C.T.C.S.S. :

12.5 kHz No

20.0 kHz Yes

25.0 kHz Single

Other kHz (Freq Hz)

Frequency Stability : (VHF) 2.5 ppm Multiple

1.5 ppm (Pattern Required)
(UHF) 1.0 ppm
External Reference Audio Response :

Number of Channels : De-emphasised

Single Flat

(Freq MHz)

Multiple R.S.S.I. : (UHF Equipment Only)

(Pattern Required) Note:All other equipment No

has RSSI as standard Yes
Special Modifications

Line Level : dBm No

Yes

Gating Operating Level : Refer to Part 08

Purchase Order Number:

T800temp.V11.doc : Issued 09 Sept 1999 Page 4 of 4

SYSTEM BLOCK DIAGRAM (OPTIONAL)

M800RACK-00-100 Section 1

Copyright TEL 30/8/99

T800SII Numbering System

Conventional Rack Systems ordered from RSD using the adjacent Numbering
System will be configured as follows:

Rack Configuration

The Racks used in these configurations are as per Section 2 of this guide, which
illustrates the factory default spe cifications.

Each Rack is fully wired and set-up for AC or DC power supply options.
(Refer to Section 3).

A Speaker / Programming Port Panel and all required Blank Panels and are fitted as
standard to each rack as required.

If the System Type is code “B”, a co-axial relay is fitted as standard. If any other
code is used, then relays must be requested if required.

Module Configuration

All Rx and Ex/Tx modules are fitted with second D-ranges as Standard.
ie.(T8XX-XX-0200)

All technical information on this Rack configuration is available from RSD.

Order Number System

14/12/1999

B A 1 W D 0 0

System

Type

Frequency

Band

RF Output

Power

Channel
Spacing

Power

Supply

Duplexer

Ancillary

Options

B =
R =
S =
P =
T =
D =

Q =

H =

L =

Base Station
Repeater
Slimline
Portable
Tone Remote
Dual Base
Quasi-Sync
HSO Rack
Liberty

(T800-22-XXXX)
(T800-22-XXXX)
(T800-23-0000)
(T800-25-XXXX)
(T800-27-XXXX)
(T800-22-001X)
(T800-24-XXXX)
(T800-28-XXXX)
(T800-56-XXXX)

A =

B =
C =
D =
E =

F =

G =

H =

I =

J =

K =

L =

66 - 88
136 - 156
148 - 174
400 - 440
440 - 480
480 - 560
800 - 880
870 - 960
220 - 244
243 - 270
265 - 285
330 - 380

(T82x-xx)
(T83x-1x)
(T83x-2x)
(T85x-1x)
(T85x-2x)
(T85x-3x)
(T88x-1x)
(T88x-2x)
(T86x-1x)
(T86x-2x)
(T86x-3x)
(T87x-2x)

MHz
MHz
MHz
MHz
MHz
MHz
MHz
MHz
MHz
MHz
MHz
MHz

1 =
2 =
3 =
4 =

25 Watts
50 Watts
90 or 100 Watts
5 Watts

0 =
1 =
2 =
3 =
4 =
5 =

No Ancillary Option
Circuit Breaker Panel
Tx/Rx Metering & Monitor Unit
Multi-Channel Panel (100 CH)
Multi-Channel Panel (10 CH)
Alarm Module

(T800-17-00XX)
(T818-01-0000)
(TA087-01-0000)
(TA387-01)
(TA136-02-0000)

0 =
1 =
2 =

No Duplexer Fitted
50 Watt Duplexer Fitted
Coaxial Relay

This item code is always set to (0)
for Slimline configurations.

If Duplexer item code is set to (1),
then Base/Repeater/Slimline
Requirement sheet must be
completed.

A =
B =

D =

Power Supply
Slimline Power Supply

DC External Power supply

(T807-10-0000)
(T808-10-0000)
(T807-23-0010)

Example: BA1WD00

Receiver

T800//

Line
level

Suppl

y

Monitor
Volume

Monitor

Mute

Off
On

Gatin

g

Sensitivit

y

Gate

Transmitter

Line

Sensitivit

y

Suppl

y

On

Microphone

Carrier

T800//

Excellence in Radio
Communications

T800//

Speaker Panel

T800//

Excellence in Radio
Communications

T800//

Excellence in Radio
Communications

T800//

Excellence in Radio
Communications

T800//

B =
A =

1 =

W =

D =

0 =
0 =

Base Station
66 -88 MHz
25 Watts
25 kHz
DC External Power supply Fitted
No Duplexer Fitted
No Ancillaries Fitted

N =

M =

W =

E =

12.5 kHz
20 kHz
25 kHz
50 kHz

Equipment list
T825-10-0200

T826-10-0200
T800-22-0000

This set-up comes complete
with all required Blank Panels
and a Speaker/Programming
Panel

X800-9x-000y

X800-9x-000y

X800-9x-000y

T8n7 - T8n7 -

T8n7 - T8n7 -

T8n6 -

Relevant Module

T number

8

8

8

8

8

7

7

7

7

8

7

Refer to

Sections 2&3

Options

shown.

Default Power

8

8

8

2

Cross-

Reference

Section

01/12/1999

Slimline

Fylde TSC Interface

Paging

Monitor (T818)

Speaker

Alarms (TA136)

Quasi Sync

Link

T803 Remote/Alarm

Portable

Optional CH/PNL

Optional relay

Optional fan

Optional Duplexer

Circuit breaker

Converter

Battery back-up

External 13.8V DC

AC

100W Transmit

50W Transmit

25W Transmit

Receive only

Dual system

Single system

Module Function

2

2

2

2

2

2

2

2

2

2

2

2

2

2

T800 - 22 - 0x00

2

2

2

2

2

2

2

2

2

2

2

2

T800 - 22 - 0x06

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

T800 - 22 - 0x10

2

2

2

2

2

2

2

2

2

2

2

2

T800 - 22 - 0x11

2

2

2

2

2

2

2

2

2

2

T800 - 22 - 0x12

2

2

2

2

2

2

2

2

2

2

2

2

2

2

T800 - 22 - 0x14

2

2

2

2

2

2

2

2

2

2

T800 - 22 - 0x15

2

2

2

2

2

2

2

2

2

2

T800 - 22 - 0x16

2

2

2

2

2

2

2

2

2

2

2

2

T800 - 22 - 0x17

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

T800 - 22 - 0x20

2

2

2

2

2

2

2

2

2

2

2

2

2

2

T800 - 22 - 0x21

2

2

2

2

2

2

2

2

2

2

2

2

2

2

T800 - 22 - 0x22

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

T800 - 22 - 0x23

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

T800 - 22 - 0x24

2

2

2

2

2

2

2

2

T800 - 23 - 0x00

2

2

2

2

2

2

2

2

T800 - 23 - 0x01

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

T800 - 24 - 0x00

2

2

2

2

2

2

2

2

2

2

2

2

2

2

T800 - 24 - 0x01

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

T800 - 24 - 0x02

Rack and Function Cross-Reference Chart

01/12/1999

Slimline

Fylde TSC Interface

Paging

Monitor (T818)

Speaker

Alarms (TA136)

Quasi Sync

Link

T803 Remote/Alarm

Portable

Optional CH/PNL

Optional relay

Optional fan

Optional Duplexer

Circuit breaker

Converter

Battery back-up

External 13.8V DC

AC

100W Transmit

50W Transmit

25W Transmit

Receive only

Dual system

Single system

Module Function

2

2

2

2

2

2

2

2

2

2

2

2

2

2

T800 - 25 - 0000

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

T800 - 25 - 0001

2

2

2

2

2

2

2

2

2

2

2

2

2

2

T800 - 25 - 0002

2

2

2

2

2

2

2

2

2

2

2

2

T800 - 27 - 0x00

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

T800 - 27 - 0x01

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

T800 - 28 - 0x00

2

2

2

2

2

2

2

2

2

2

T800 - 29 - 0x00

2

2

2

2

2

2

2

2

2

2

2

2

2

2

T800 - 29 - 0x01

2

2

2

2

2

2

2

2

T800 - 29 - 0x02

Rack and Function Cross-Reference Chart

T800 SeriesII Rack and Module Weights

Weight (kg)

0.00

Rackframe

to house 2 modules 3.60
to house 3 modules 4.15
to house 4 modules 4.70
to house 5 modules 5.25
to house 6 modules 5.80
to house 7 modules 6.35

T8n5 Receiver 2.20
T8n6 Transmitter 2.05
T8n7 Exciter 2.05

50W Power Amplifier 3.20
100W Power Amplifier 3.55

T80n Power Supply 2.30
Circuit breaker 0.50
DC Converter Module 0.90

TA136 Alarm Unit 0.85
T818 Monitor 0.95
TA807 Channel Panel 0.35
TA320 Combiner 2.80
Duplexer 1.15
Duplexer Cradle 0.55
T803 Tone Remote / Alarm 1.55
T801-20 High Stability Oscillator 1.50

Portable Repeater Case

to house 3 modules (Standard) 6.00
to house 4 modules 6.15

2 Batteries (Standard) 5.60

01/12/1999

T800 Series

II

Conventional Equipment

Reference Guide

Rack

Configuration

M800RACK-00-100 Section 2

Copyright TEL 30/8/99

T800-22-0x00

A standard single channel rack for repeater or base station use; up to 100 Watt
output.

Operational Characteristics

• Single channel

• Up to 100W with option of Transmitter or Exciter / PA combination

• Speaker / Programming panel

• DC line fuse

• Earth stud

• Backplane interface

Power Supply Options

• x = 0 AC only

• x = 1 External DC only

• x = 2 AC and External DC

• x = 3 AC and Battery

• x = 4 External DC and Battery

• x = 5 AC and External DC and Battery

Configuration Options

• Duplexer

• Coaxial Relay

• Fans - single or double

• Interfaces to Changeover Module TA703-00-xxxx using TA703-11-0010

installation kit

• microphone

• DC converter

Mechanical Characteristics

• 5 Rack Units x 19” ra ck to house up to 7 modules

• Size

Height - 222mm
Width - 482mm
Depth - 322mm plus 50mm clearance space

• Weight – (rackframe with modules shown)
25W - 11.25kg
50W - 14.45kg
100W - 14.80kg

NOTE:

This product offers the versatility of fitting personality boards to provide
customised solutions for specific requirements.
Refer to RSD for design and build of personality boards.

Rack “Items Supplied as Standard” does not include modules other than those listed
on the drawing.

T A I T

Radio Communications
Christchurch
New Zealand

DRAWING:

T800-22-0x00 RACKFRAME

TITLE:

RACK, SNGL<100W, (OPT BD

Drawn DateChecked

AMM 22/10/98ABB

AMM 24/8/99ABB

AMM 14/12/98ABB

AMM 8/3/99ABB

AMM 26/11/99ABB

Version

1

4

2

3

5

Original

Drawing No changed and Ref. added

Change of Title

Parts list added

Drawing name changed

FRONT VIEW

REAR VIEW

T800//

Power Supply

Power

On

Standby

Overload

Receiver

T800//

Line
level

Supply

Monitor
Volume

Monitor

Mute

Off
On

Gating

Sensitivity

Gate

Exciter

Line

Sensitivity

Supply

On

Microphone

Carrier

T800// T800//

Power

Low forward power

High reverse power

Supply

Power Amplifier

Excellence in Radio
Communications

T800//

Excellence in Radio
Communications

T800//

Speaker Panel

T800//

OPTIONAL

TRANSMITTER

OPTIONAL

BLANK

OPTIONAL

DUPLEXER

FAN (OPTIONAL)

OPTIONAL

BLANK

ITEMS SUPPLIED AS STANDARD

PART NUMBER DESCRIPTION

1T800-22-0004 RACK, FRAME ONLY, ASSEMBLED

QTY

1T800-41-0002 DOUBLE GUIDE KIT
1T800-45-0000 GUIDE PA 50W KIT
1T800-44-0000 T800 PS GUIDE KIT
1T800-15-0000 SPEAKER / PROGRAM PANEL

1T800-50-0000 BACKPLANE
1X800-90-0000 POWER RAIL (STANDARD)

1T800-40-0000 FIXING KIT ONLY
2T800-40-0001 BLANKING BRACKET / FRONT PANEL

SECTION 4

REFERENCE

SECTION 4
SECTION 4
SECTION 4
SECTION 8

SECTION 5
SECTION 3

SECTION 4
SECTION 8

REFER TO SECTION 3

OF THE

REFERENCE GUIDE

FOR

POWER RAIL OPTIONS

EARTH

STUD

FUSE

TB1

OUTPUT

ONLY 13.8V

MAX

2 AMPS

Power
Supply

Output

13.8V
25A
Max.

+

-

1
2
3
4
5

PA ReceiverExciter

T800-50-0000

Speaker

Panel

FAN (OPTIONAL)

M800RACK-00-100 Section 2

Copyright TEL 30/8/99

T800-22-0x06

A 25 Watt single channel rack for repeater or link use.

Operational Characteristics

•

Single channel

•

Up to 25W Transmitter Output

•

Speaker / Programming panel

•

DC line fuse

•

Earth stud

•

Backplane interface

Power Supply Options

•

x = 0 AC only

•

x = 1 External DC only

•

x = 2 AC and External DC

•

x = 3 AC and Battery

•

x = 4 External DC and Battery

•

x = 5 AC and External DC and Battery

Configuration Options

•

Duplexer

•

Coaxial Relay

•

Fans - single or double

•

Interfaces to Changeover Module TA703-00-xxxx using TA703-11-0010

installation kit

•

Microphone

•

DC converter

Mechanical Characteristics

•

5 Rack Units x 19” rack to house up to 7 modules

•

Size

Height - 222mm
Width - 482mm
Depth - 322mm plus 50mm clearance space

•

Weight – (rackframe with modules shown)

7.85kg

NOTE:

This product offers the versatility of fitting personality boards to provide
customised solutions for specific requirements.
Refer to RSD for design and build of personality boards.

Rack “Items Supplied as Standard” does not include modules other than those listed
on the drawing.

T A I T

Radio Communications
Christchurch
New Zealand

DRAWING:

T800-22-0x06

TITLE:

RACK, REPEATER/LINK END DC

Drawn DateChecked

AMM 19/2/99ABB

AMM 24/8/99ABB

Version

12Original

Drawing No changes and Ref. added

Transmitter

Line

Sensitivity

Supply

On

Microphone

Carrier

T800//

Speaker Panel

T800//

Receiver

T800//

Line
level

Supply

Monitor

Volume

Monitor

Mute

Off
On

Gating

Sensitivity

Gate

Excellence in Radio
Communications

T800//

Excellence in Radio
Communications

T800//

Excellence in Radio
Communications

T800//

Excellence in Radio
Communications

T800//

FRONT VIEW

REAR VIEW

ITEMS SUPPLIED AS STANDARD

PART NUMBER DESCRIPTION

1T800-22-0004 RACK, FRAME ONLY, ASSEMBLED

QTY

1T800-41-0002 DOUBLE GUIDE KIT
1T800-15-0000 SPEAKER / PROGRAM PANEL

1T800-50-0000 BACKPLANE
1X800-91-0000 POWER RAIL (STANDARD)

1T800-40-0000 FIXING KIT ONLY
2T800-40-0001 BLANKING BRACKET / FRONT PANEL

SECTION 4

REFERENCE

SECTION 4
SECTION 8

SECTION 5
SECTION 3

SECTION 4
SECTION 8

REFER TO SECTION 3

OF THE

REFERENCE GUIDE

FOR

POWER RAIL OPTIONS

EARTH

STUD

DC INPUT FUSE

TB1

OUTPUT

ONLY 13.8V

MAX

2 AMPS

ReceiverTransmitter

T800-50-0000

Speaker

Panel

M800RACK-00-100 Section 2

Copyright TEL 30/8/99

T800-22-0x10

A single channel repeater or base station rack based on the standard T800-22-0x00,
with the option of fitting a Channel Panel.

Operational Characteristics

•

Single channel

•

Up to 100W with option of Transmitter or Exciter / PA combination

•

Speaker / Programming panel

•

DC line fuse

•

Earth stud

•

Backplane interface

Power Supply Options

•

x = 0 AC only

•

x = 1 External DC only

•

x = 2 AC and External DC

•

x = 3 AC and Battery

•

x = 4 External DC and Battery

•

x = 5 AC and External DC and Battery

Configuration Options

•

Channel Panel

•

Duplexer

•

Coaxial Relay

•

Fans - single or double

•

Interfaces to Changeover Module TA703-00-xxxx using TA703-11-0011

installation kit

•

microphone

•

DC converter

Mechanical Characteristics

•

5 Rack Units x 19” rack to house up to 7 modules

•

Size

Height - 222mm
Width - 482mm
Length - 322mm plus 50mm clearance space

•

Weight – (rackframe with modules shown)

25W - 11.25kg
50W - 14.45kg
100W - 14.80kg

Rack “Items Supplied as Standard” does not include modules other than those listed
on the drawing.

T A I T

Radio Communications
Christchurch
New Zealand

DRAWING:

T800-22-0x10 RACKFRAME

TITLE

RACK, SNGL<100W, (CH PNL

Drawn DateChecked

AMM 21/10/98ABB

AMM 25/8/99ABB

AMM 14/12/98ABB

AMM 8/3/99ABB

AMM 26/11/99ABB

Version

1

4

2

3

5

Original

Drg No changed and Ref added

Change of Title

Parts list added

Drawing name changed

FRONT VIEW

REAR VIEW

T800//

Power Supply

Power

On

Standby

Overload

Receiver

T800//

Line

level

Supply

Monitor
Volume

Monitor

Mute

Off
On

Gating

Sensitivity

Gate

Exciter

Line

Sensitivity

Supply

On

Microphone

Carrier

T800// T800//

Power

Low forward power

High reverse power

Supply

Power Amplifier

Excellence in Radio
Communications

T800//

Excellence in Radio
Communications

T800//

Speaker Panel

T800//

OPTIONAL

TRANSMITTER

OPTIONAL

BLANK

OPTIONAL

DUPLEXER

OPTIONAL
CHANNEL

PANEL

FAN (OPTIONAL)

OPTIONAL

BLANK

1X800-90-0000 POWER RAIL (STANDARD)

SECTION 4

REFERENCE

SECTION 4
SECTION 4
SECTION 4
SECTION 8

SECTION 5
SECTION 3

SECTION 4
SECTION 8

ITEMS SUPPLIED AS STANDARD

PART NUMBER DESCRIPTION

1T800-22-0004 RACK, FRAME ONLY, ASSEMBLED

QTY

1T800-41-0002 DOUBLE GUIDE KIT
1T800-45-0000 GUIDE PA 50W KIT
1T800-44-0000 T800 PS GUIDE KIT
1T800-15-0000 SPEAKER / PROGRAM PANEL

1T800-50-0001 BACKPLANE CH-PNL

1T800-40-0000 FIXING KIT ONLY
2T800-40-0001 BLANKING BRACKET / FRONT PANEL

REFER TO SECTION 3

OF THE

REFERENCE GUIDE

FOR

POWER RAIL OPTIONS

Power
Supply

Output

13.8V
25A
Max.

+

-

1
2
3
4
5

PA ReceiverExciter

T800-50-0001

Speaker

Panel

EARTH

STUD

FUSE

TB1

OUTPUT

ONLY 13.8V

MAX

2 AMPS

FAN (OPTIONAL)

M800RACK-00-100 Section 2

Copyright TEL 30/8/99

T800-22-0x11

A Receiver only rack with alarm outputs, AC power supply and dual battery back-up
connections.

Operational Characteristics

•

Receive only - up to 4 receivers

•

Speaker / Programming panel - with Receiver Speaker Select Switch

•

Alarm Panel

•

DC line fuse

•

Earth stud

•

Backplane interface

Power Supply Options

•

x = 0 AC only

•

x = 1 External DC only

•

x = 2 AC and External DC

•

x = 3 AC and Battery

•

x = 4 External DC and Battery

•

x = 5 AC and External DC and Battery

Configuration Options

•

Channel Panel

•

Fans - single or double

•

DC converter

Mechanical Characteristics

•

5 Rack Units x 19” rack to house up to 7 modules

•

Size

Height - 222mm
Width - 482mm
Depth - 322mm plus 50mm clearance space

•

Weight – (rackframe with modules shown)

17.75kg

Rack “Items Supplied as Standard” does not include modules other than those listed
on the drawing.

T A I T

Radio Communications
Christchurch
New Zealand

DRAWING:

T800-22-0x11

TITLE:

RACK, RX ONLY AC

(4RX + ALARM + SPK)

Drawn DateChecked

AMM 20/10/98AB B

AMM 22/7/99ABB

AMM 14/12/98AB B

AMM 8/3/99ABB

AMM 25/8/99ABB

Version

1

4

2

3

4

Original

Frame label removed

Change of Title

Parts list added

drg No changed and Ref added

FRONT VIEW

REAR VIEW

Receiver

T800//

Line
level

Supply

Monitor

Volume

Monitor

Mute

Off
On

Gating

Sensitivity

Gate

T800//

Power Supply

Power

On

Standby

Overload

Speaker Panel

T800// T800//

Alarm Panel

Power

PSU Fail

Forward

Test

Batt Fail

Forward

Reflected

Alarm#1

Alarm#2

Alarm#3

Alarm#4

Receiver

T800//

Line
level

Supply

Monitor

Volume

Monitor

Mute

Off
On

Gating

Sensitivity

Gate

Receiver

T800//

Line
level

Supply

Monitor
Volume

Monitor

Mute

Off

On

Gating

Sensitivity

Gate

Receiver

T800//

Line
level

Supply

Monitor

Volume

Monitor

Mute

Off
On

Gating

Sensitivity

Gate

OPTIONAL

CHANNEL

PANEL

OPTIONAL

or BLANK

Receiver

Speaker Select

16

25

34

1X800-93-0000 POWER RAIL (STANDARD)

SECTION 4

REFERENCE

SECTION 4
SECTION 4
SECTION 4
SECTION 8

SECTION 5
SECTION 3

SECTION 4

ITEMS SUPPLIED AS STANDARD

PART NUMBER DESCRIPTION

1T800-11-0004 RACK, FRAME ONLY, ASSEMBLED 2 BATT BACK-UP

QTY

2T800-41-0002 DOUBLE GUIDE KIT
1T800-43-0000 GUIDE KIT T1500/300 DOUBLE 'D'
1T800-44-0000 T800 PS GUIDE KIT
1T800-15-0002 SPEAKER / PROGRAM PANEL WITH 6-WAY SWITCH

2T800-50-0002 BACKPLANE

1T800-40-0000 FIXING KIT ONLY

Power
Supply

Output

13.8V
25A
Max.

+

-

1
2
3
4
5

Alarm

ReceiverReceiverReceiverReceiver

T800-50-0002 T800-50-0002

Speaker

Panel

EARTH

STUD

BATTERY
BACK-UP

FUSE

TB1

DIODE

PACK

OUTPUT

ONLY 13.8V

MAX

2 AMPS

REFER TO SECTION 3

OF THE

REFERENCE GUIDE

FOR

POWER RAIL OPTIONS

M800RACK-00-100 Section 2

Copyright TEL 30/8/99

T800-22-0x12

Receive only rack similar to T800-22-0x11; but with no alarm outputs.

Operational Characteristics

•

Receive only - up to 4 receivers

•

Speaker / Programming panel - with Receiver Speaker Select Switch

•

DC line fuse

•

Earth stud

•

Backplane interface

Power Supply Options

•

x = 0 AC only

•

x = 1 External DC only

•

x = 2 AC and External DC

•

x = 3 AC and Battery

•

x = 4 External DC and Battery

•

x = 5 AC and External DC and Battery

Configuration Options

•

Channel Panel

•

Fans - single or double

•

DC converter

Mechanical Characteristics

•

5 Rack Units x 19” rack to house up to 7 modules

•

Size

Height - 222mm
Width - 482mm
Depth - 322mm plus 50mm clearance space

•

Weight – (rackframe with modules shown)

16.35kg

Rack “Items Supplied as Standard” does not include modules other than those listed
on the drawing.

T A I T

Radio Communications
Christchurch
New Zealand

DRAWING:

T800-22-0x12

TITLE:

RACK, RX ONLY AC (4RX + SPK)

Drawn DateChecked

AMM 20/10/98AB B

AMM 25/8/99ABB

AMM 14/12/98AB B

AMM 8/3/99ABB

Version

1

3

2

3

Original

drg No changed and Ref added

Change of Title

Parts list added

FRONT VIEW

REAR VIEW

Receiver

T800//

Line
level

Supply

Monitor

Volume

Monitor

Mute

Off
On

Gating

Sensitivity

Gate

T800//

Power Supply

Power

On

Standby

Overload

Receiver

T800//

Line
level

Supply

Monitor

Volume

Monitor

Mute

Off
On

Gating

Sensitivity

Gate

Receiver

T800//

Line
level

Supply

Monitor
Volume

Monitor

Mute

Off

On

Gating

Sensitivity

Gate

Receiver

T800//

Line
level

Supply

Monitor

Volume

Monitor

Mute

Off
On

Gating

Sensitivity

Gate

OPTIONAL

CHANNEL

PANEL

OPTIONAL

or BLANK

Excellence in Radio
Communications

T800//

Speaker Panel

T800//

Receiver

Speaker Select

16

25

34

1X800-90-0000 POWER RAIL (STANDARD)

SECTION 4

REFERENCE

SECTION 4
SECTION 4
SECTION 8
SECTION 8

SECTION 5
SECTION 3

SECTION 4

ITEMS SUPPLIED AS STANDARD

PART NUMBER DESCRIPTION

1T800-22-0004 RACK, FRAME ONLY, ASSEMBLED

QTY

2T800-41-0002 DOUBLE GUIDE KIT
1T800-44-0000 T800 PS GUIDE KIT

1T800-15-0002 SPEAKER / PROGRAM PANEL WITH 6-WAY SWITCH

2T800-50-0002 BACKPLANE

1T800-40-0000 FIXING KIT ONLY

1T800-40-0001 BLANKING BRACKET / FRONT PANEL

Power
Supply

Output

13.8V
25A
Max.

+

-

1
2
3
4
5

ReceiverReceiverReceiverReceiver

T800-50-0002 T800-50-0002

Speaker

Panel

EARTH

STUD

FUSE

TB1

OUTPUT

ONLY 13.8V

MAX

2 AMPS

REFER TO SECTION 3

OF THE

REFERENCE GUIDE

FOR

POWER RAIL OPTIONS

M800RACK-00-100 Section 2

Copyright TEL 30/8/99

T800-22-0x13

A dual 50 Watt channel rack, with AC power supply and DC battery back-up
connections.

Operational Characteristics

•

Dual channel

•

50W output

•

Speaker / Programming panel

•

DC line fuse

•

Earth stud

•

Backplane interface

Power Supply Options

•

x = 0 AC only

•

x = 1 External DC only Not Available

(see T800-22-0x16)

•

x = 2 AC and External DC

•

x = 3 AC and Battery

•

x = 4 External DC and Battery Not Available

(see T800-22-0x16)

•

x = 5 AC and External DC and Battery

Configuration Options

•

Coaxial Relay

•

Fans - single or double

•

Interfaces to Changeover Module TA703-00-xxxx using TA703-11-0011

installation kit

•

microphone

Mechanical Characteristics

•

5 Rack Units x 19” rack to house up to 7 modules

•

Size

Height - 222mm
Width - 482mm
Depth - 322mm plus 50mm clearance space

•

Weight – (rackframe with modules shown)

23.55kg

Rack “Items Supplied as Standard” does not include modules other than those listed
on the drawing.

T A I T

Radio Communications
Christchurch
New Zealand

DRAWING:

T800-22-0x13 RACKFRAME

TITLE:

RACK, DUAL 2x50W

Drawn DateChecked

AMM 18/2/99ABB

AMM 25/8/99ABB

AMM 29/11/99ABB

Version

1

2

3

Original

Drg No change, ref added, PS,PA moved

Drg name changed

FRONT VIEW

REAR VIEW

T800//

Power Supply

Power

On

Standby

Overload

Receiver

T800//

Line
level

Supply

Monitor
Volume

Monitor

Mute

Off
On

Gating

Sensitivity

Gate

Exciter

Line

Sensitivity

Supply

On

Microphone

Carrier

T800//T800//

Power

Low forward power

High reverse power

Supply

Power Amplifier Receiver

T800//

Line
level

Supply

Monitor
Volume

Monitor

Mute

Off
On

Gating

Sensitivity

Gate

Exciter

Line

Sensitivity

Supply

On

Microphone

Carrier

T800// T800//

Power

Low forward power

High reverse power

Supply

Power Amplifier

FAN (OPTIONAL) FAN (OPTIONAL)

1X800-93-0002 POWER RAIL (STANDARD)

SECTION 4

REFERENCE

SECTION 4
SECTION 4
SECTION 4
SECTION 5
SECTION 3

ITEMS SUPPLIED AS STANDARD

PART NUMBER DESCRIPTION

1T800-24-0004 RACK, FRAME ONLY, ASSEMBLED BATTERY BACK-UP

QTY

2T800-41-0002 DOUBLE GUIDE KIT
2T800-45-0000 GUIDE PA 50W KIT
1T800-44-0000 T800 PS GUIDE KIT
2T800-50-0001 BACKPLANE

The rack configuration has been changed to reduce

the risk of overheating in some environments.

It is recommended that the optional fans are fitted.

EARTH

STUD

BATTERY
BACK-UP

FUSE

TB1

DIODE

PACK

OUTPUT

ONLY 13.8V

MAX

2 AMPS

FUSE

Power
Supply

Output

13.8V
25A
Max.

+

-

1
2
3
4
5

FAN

(OPTIONAL)

PA ReceiverExciter

T800-50-0001

ReceiverExciter

T800-50-0001

PA

FAN

(OPTIONAL)

REFER TO SECTION 3

OF THE

REFERENCE GUIDE

FOR

POWER RAIL OPTIONS

M800RACK-00-100 Section 2

Copyright TEL 30/8/99

T800-22-0x14

A dual 25 Watt channel rack, with AC power supply and DC battery back-up
connections.

Operational Characteristics

•

Dual channel

•

25W output

•

Dual Speaker / Programming panel (switchable)

•

DC line fuse

•

Earth stud

•

Backplane interface

Power Supply Options

•

x = 0 AC only

•

x = 1 External DC only Not Available

(see T800-22-0x17)

•

x = 2 AC and External DC

•

x = 3 AC and Battery

•

x = 4 External DC and Battery Not Available

(see T800-22-0x17)

•

x = 5 AC and External DC and Battery

Configuration Options

•

Channel Panel

•

Individual Speaker / Programming panels

•

Duplexer

•

Coaxial Relay

•

Fans - single or double

•

Interfaces to Changeover Module TA703-00-xxxx using TA703-11-0011

installation kit

•

microphone

•

DC converter

Mechanical Characteristics

•

5 Rack Units x 19” rack to house up to 7 modules

•

Size

Height - 222mm
Width - 482mm
Depth - 322mm plus 50mm clearance space

•

Weight – (rackframe with modules shown)

16.05kg

Rack “Items Supplied as Standard” does not include modules other than those listed
on the drawing.

T A I T

Radio Communications
Christchurch
New Zealand

DRAWING:

T800-22-0x14 RACKFRAME

TITLE:

RACK, DUAL 2x25W, SPK SW

Drawn DateChecked

AMM 12/1/99ABB

AMM 2/9/99ABB

AMM 18/3/99ABB

AMM 25/8/99ABB

AMM 29/11/99ABB

Version

1

4

2

3

5

Original

Dual spk replaced by switched spk

Parts list added, fans removed

Drg No changed, ref added, PA, PS moved

Drg name changed

FRONT VIEW

REAR VIEW

T800//

Power Supply

Power

On

Standby

Overload

Receiver

T800//

Line
level

Supply

Monitor

Volume

Monitor

Mute

Off
On

Gating

Sensitivity

Gate

Transmitter

Line

Sensitivity

Supply

On

Microphone

Carrier

T800//

OPTIONAL SPEAKER

(T800-15-0000)

OPTIONAL DUPLEXER

AND/OR CHANNEL PANEL

Receiver

T800//

Line
level

Supply

Monitor
Volume

Monitor

Mute

Off

On

Gating

Sensitivity

Gate

Transmitter

Line

Sensitivity

Supply

On

Microphone

Carrier

T800//

Speaker Panel

T800//

RX 1

RX 2

O
F
F

O
F
F

Excellence in Radio
Communications

T800//

OPTIONAL SPEAKER

(T800-15-0000)

OPTIONAL DUPLEXER

AND/OR CHANNEL PANEL

1T800-40-0001 BLANKING BRACKET / FRONT PANEL SECTION 8

1X800-93-0001 POWER RAIL (STANDARD)

SECTION 4

REFERENCE

SECTION 4
SECTION 4
SECTION 8

SECTION 5
SECTION 3

SECTION 4

ITEMS SUPPLIED AS STANDARD

PART NUMBER DESCRIPTION

1T800-24-0004 RACK, FRAME ONLY, ASSEMBLED, BATTERY BACK-UP

QTY

2T800-41-0002 DOUBLE GUIDE KIT

1T800-15-0003 SPEAKER / PROGRAM PANEL

2T800-50-0001 BACKPLANE

1T800-40-0000 FIXING KIT ONLY

1T800-44-0000 T800 PS GUIDE KIT

Power

Supply

Output

13.8V
25A
Max.

+

-

1
2
3
4
5

ReceiverTransmitter

T800-50-0001

Speaker

Panel

ReceiverTransmitter

T800-50-0001

EARTH

STUD

BATTERY
BACK-UP

FUSE

TB1

DIODE

PACK

OUTPUT

ONLY 13.8V

MAX

2 AMPS

FUSE

REFER TO SECTION 3

OF THE

REFERENCE GUIDE

FOR

POWER RAIL OPTIONS

M800RACK-00-100 Section 2

Copyright TEL 30/8/99

T800-22-0x15

A dual 25 Watt channel rack with a separate power supply for each channel. The
speaker panel can be switched between receivers.

Operational Characteristics

•

Dual channel

•

25W output

•

Speaker / Programming panel, with Receiver Selectable Switch

•

DC line fuse

•

Earth stud

•

Backplane interface

Power Supply Options

•

x = 0 AC only

•

x = 1 External DC only

•

x = 2 AC and External DC

•

x = 3 AC and Battery

•

x = 4 External DC and Battery

•

x = 5 AC and External DC and Battery

Configuration Options

•

Coaxial Relay

•

Fans - single or double

•

Interfaces to Changeover Module TA703-00-xxxx using TA703-11-0011

installation kit

•

microphone

•

DC converter

Mechanical Characteristics

•

5 Rack Units x 19” rack to house up to 7 modules

•

Size

Height - 222mm
Width - 482mm
Depth - 322mm plus 50mm clearance space

•

Weight – (rackframe with modules shown)

16.6kg

Rack “Items Supplied as Standard” does not include modules other than those listed
on the drawing.

T A I T

Radio Communications
Christchurch
New Zealand

DRAWING:

T800-22-0x15 RACKFRAME

TITLE:

RACK, DUAL 2x25 WATT, (2 P/SUP

Drawn DateChecked

AMM 12/1/99ABB

AMM 29/11/99ABB

AMM 3/2/99ABB

AMM 25/8/99ABB

Version

1

3

2

3

Original

Drg name changed

Standard supply table added

Drg No changed, Ref added, Relay removed

FRONT VIEW

REAR VIEW

T800//

Power Supply

Power

On

Standby

Overload

Rec eiver

T800//

Line
level

Supply

Monitor
Volume

Monitor

Mute

Off
On

Gating

Sensitivity

Gate

T800//

Power Supply

Power

On

Standby

Overload

Transmitter

Line

Sensitivity

Supply

On

Microphone

Carrier

T800//

Rec eiver

T800//

Line
level

Supply

Monitor
Volume

Monitor

Mute

Off
On

Gating

Sensitivity

Gate

Transmitter

Line

Sensitivity

Supply

On

Microphone

Carrier

T800//

Speaker Panel

T800//

RX 1

RX 2

O
F
F

O
F
F

1X800-22-0015 POWER RAIL (STANDARD)

SECTION 4

REFERENCE

SECTION 4
SECTION 4
SECTION 8

SECTION 5
SECTION 3

SECTION 4

ITEMS SUPPLIED AS STANDARD

PART NUMBER DESCRIPTION

1T800-24-0004 RACK, FRAME ONLY, ASSEMBLED

QTY

2T800-41-0002 DOUBLE GUIDE KIT
2T800-44-0000 T800 PS GUIDE KIT
1T800-15-0003 SPEAKER/PROGRAM PANEL WITH 3 POSITION SWITCH
1T800-40-0000 FIXING KIT ONLY
2T800-50-0001 BACKPLANE

Power

Supply

Output

13.8V
25A
Max.

+

-

1
2
3
4
5

Speaker

Panel

ReceiverTransmitter

T800-50-0001

Power
Supply

Output

13.8V
25A
Max.

+

-

1
2
3
4
5

EARTH

STUD

FUSE

TB1

OUTPUT

ONLY 13.8V

MAX

2 AMPS

FUSE

DIODE

PACK

ReceiverTransmitter

T800-50-0001

REFER TO SECTION 3

OF THE

REFERENCE GUIDE

FOR

POWER RAIL OPTIONS

M800RACK-00-100 Section 2

Copyright TEL 30/8/99

T800-22-0x16

A dual 50 Watt channel rack for use in DC only situations.

Operational Characteristics

•

Dual channel

•

50W output per channel

•

Speaker / Programming panel, with Receiver Selectable Switch

•

DC line fuse

•

Earth stud

•

Backplane interface

Power Supply Options

•

x = 0 AC only Not Available

•

x = 1 External DC only

•

x = 2 AC and External DC Not Available

•

x = 3 AC and Battery Not Available

•

x = 4 External DC and Battery

•

x = 5 AC and External DC and Battery Not Available

Configuration Options

•

Coaxial Relay

•

Fans - single or double

•

Interfaces to Changeover Module TA703-00-xxxx using TA703-11-0011

installation kit

•

microphone

Mechanical Characteristics

•

5 Rack Units x 19” rack to house up to 7 modules

•

Size

Height - 222mm
Width - 482mm
Depth - 322mm plus 50mm clearance space

•

Weight – (rackframe with modules shown)

20.7kg

Rack “Items Supplied as Standard” does not include modules other than those listed
on the drawing.

T A I T

Radio Communications
Christchurch
New Zealand

DRAWING:

T800-22-0x16 RACKFRAME

TITLE:

RACK, DUAL 2x50W, (SPK SWITCHED)

Drawn DateChecked

AMM 15/2/99ABB

AMM 25/8/99ABB

AMM 29/11/99ABB

Version

1

2

3

Original

Drg No changed, Ref added, PA moved

Drg name changed

FRONT VIEW

REAR VIEW

Receiver

T800//

Line
level

Supply

Monitor

Volume

Monitor

Mute

Off
On

Gating

Sensitivity

Gate

Exciter

Line

Sensitivity

Supply

On

Microphone

Carrier

T800//T800//

Power

Low forward power

High reverse power

Supply

Power Amplifier Receiver

T800//

Line
level

Supply

Monitor
Volume

Monitor

Mute

Off
On

Gating

Sensitivity

Gate

Exciter

Line

Sensitivity

Supply

On

Microphone

Carrier

T800// T800//

Power

Low forward power

High reverse power

Supply

Power AmplifierSpeaker Panel

T800//

RX 1 RX 2

O
F
F

O
F
F

FAN (OPTIONAL)FAN (OPTIONAL)

1X800-91-0002 POWER RAIL (STANDARD)

SECTION 4

REFERENCE

SECTION 4
SECTION 4
SECTION 8

SECTION 5
SECTION 3

SECTION 4

ITEMS SUPPLIED AS STANDARD

PART NUMBER DESCRIPTION

1T800-22-0004 RACK, FRAME ONLY, ASSEMBLED

QTY

2T800-41-0002 DOUBLE GUIDE KIT
2T800-45-0000 GUIDE PA 50W KIT
1T800-15-0003 SPEAKER/PROGRAM PANEL WITH 3 POSITION SWITCH
1T800-40-0000 FIXING KIT ONLY
2T800-50-0001 BACKPLANE

The rack configuration has been changed to reduce

the risk of overheating in some environments.

It is recommended that the optional fans are fitted.

EARTH

STUD

DC INPUT FUSE

TB1

OUTPUT

ONLY 13.8V

MAX

2 AMPS

FUSE

ReceiverPA Exciter

T800-50-0001

FAN

(OPTIONAL)

Speaker

Panel

Exciter Receiver

T800-50-0001

PA

FAN (OPTIONAL)

REFER TO SECTION 3

OF THE

REFERENCE GUIDE

FOR

POWER RAIL OPTIONS

M800RACK-00-100 Section 2

Copyright TEL 30/8/99

T800-22-0x17

A dual 25 Watt channel rack for use in DC only situations.

Operational Characteristics

•

Dual channel

•

25W output per channel

•

Speaker / Programming panel, with Receiver Selectable Switch

•

DC line fuse

•

Earth stud

•

Backplane interface

Power Supply Options

•

x = 0 AC only Not Available

(see T800-22-0x14)

•

x = 1 External DC only

•

x = 2 AC and External DC Not Available

(see T800-22-0x14)

•

x = 3 AC and Battery Not Available

(see T800-22-0x14)

•

x = 4 External DC and Battery

•

x = 5 AC and External DC and Battery Not Available

(see T800-22-0x14)

Configuration Options

•

Channel Panel

•

Duplexer

•

Coaxial Relay

•

Fans - single or double

•

Interfaces to Changeover Module TA703-00-xxxx using TA703-11-0011

installation kit

•

microphone

Mechanical Characteristics

•

5 Rack Units x 19” rack to house up to 7 modules

•

Size

Height - 222mm
Width - 482mm
Depth - 322mm plus 50mm clearance space

•

Weight – (rackframe with modules shown)

13.2kg

Rack “Items Supplied as Standard” does not include modules other than those listed
on the drawing.

T A I T

Radio Communications
Christchurch
New Zealand

DRAWING:

T800-22-0x17 RACKFRAME

TITLE:

RACK, DUAL 2X25W, (SPKR SW)

Drawn DateChecked

AMM 2/6/99ABB

AMM 25/8/99ABB

AMM 29/11/99ABB

Version

1

2

3

Original

Drg No changed, Ref added

Drg name changed

FRONT VIEW

REAR VIEW

Receiver

T800//

Line
level

Supply

Monitor

Volume

Monitor

Mute

Off
On

Gating

Sensitivity

Gate

Transmitter

Line

Sensitivity

Supply

On

Microphone

Carrier

T800//

Excellence in Radio
Communications

T800//

OPTIONAL

DUPLEXER

and/or

CHANNEL

PANEL

OPTIONAL

BLANK

Speaker Panel

T800//

Receiver

T800//

Line
level

Supply

Monitor
Volume

Monitor

Mute

Off
On

Gating

Sensitivity

Gate

Transmitter

Line

Sensitivity

Supply

On

Microphone

Carrier

T800//

Excellence in Radio
Communications

T800//

RX 1 RX 2

O
F
F

O
F
F

OPTIONAL

DUPLEXER

and/or

CHANNEL

PANEL

1X800-91-0001 POWER RAIL (STANDARD)

SECTION 4

REFERENCE

SECTION 4
SECTION 8

SECTION 5
SECTION 3

SECTION 4
SECTION 8

ITEMS SUPPLIED AS STANDARD

PART NUMBER DESCRIPTION

1T800-22-0004 RACK, FRAME ONLY, ASSEMBLED

QTY

2T800-41-0002 DOUBLE GUIDE KIT
1T800-15-0003 SPEAKER / PROGRAM PANEL 3-WAY SWITCH

2T800-50-0001 BACKPLANE

2T800-40-0000 FIXING KIT ONLY
2T800-40-0001 BLANKING BRACKET / FRONT PANEL

ReceiverTransmitter

Speaker

Panel

ReceiverTransmitter

EARTH

STUD

DC INPUT FUSE

TB1

OUTPUT

ONLY 13.8V

MAX

2 AMPS

FUSE

T800-50-0001 T800-50-0001

DR2DR1

REFER TO SECTION 3

OF THE

REFERENCE GUIDE

FOR

POWER RAIL OPTIONS

M800RACK-00-100 Section 2

Copyright TEL 30/8/99

T800-22-0x20

A single repeater or base station channel rack up to 100 Watt maximum output. The
rack can accommodate an Rx/Tx Monitor panel and AC power input.

Operational Characteristics

•

Single channel

•

Up to 100W with option of Transmitter or Exciter / PA combination

•

Speaker / Programming panel

•

Rx/Tx Monitor Panel

•

DC line fuse

•

Earth stud

•

Backplane interface

Power Supply Options

•

x = 0 AC only

•

x = 1 External DC only Not Available

•

x = 2 AC and External DC

•

x = 3 AC and Battery

•

x = 4 External DC and Battery Not Available

•

x = 5 AC and External DC and Battery

Configuration Options

•

Channel Panel

•

Duplexer

•

Coaxial Relay

•

Fans - single or double

•

Interfaces to Changeover Module TA703-00-xxxx using TA703-11-0011

installation kit

•

microphone

•

DC converter

Mechanical Characteristics

•

5 Rack Units x 19” rack to house up to 7 modules

•

Size

Height - 222mm
Width - 482mm
Depth - 322mm plus 50mm clearance space

•

Weight – (rackframe with modules shown)

25W - 12.2kg
50W - 15.95kg
100W - 16.3kg

NOTE:

This product offers the versatility of fitting personality boards to provide
customised solutions for specific requirements.
Refer to RSD for design and build of personality boards.

Rack “Items Supplied as Standard” does not include modules other than those listed
on the drawing.

T A I T

Radio Communications
Christchurch
New Zealand

DRAWING:

T800-22-0x20 RACKFRAME

TITLE:

RACK, SNGL<100W, (MONITOR)

Drawn DateChecked

AMM 12/1/99ABB

AMM 29/11/99ABB

AMM 8/3/99ABB

AMM 25/8/99ABB

Version

1

4

2

3

Original

Drg name changed

Parts list added

Drg No changed, Ref added

FRONT VIEW

REAR VIEW

OPTIONAL

DUPLEXER

OPTIONAL

CHANNEL

PANEL

Rx/Tx Monitor

T800//

Supply

Volume

Volts
Rx Signal
Rx Line
Tx Line
Fwd Pwr
Rev Pwr

Off

Speaker Panel

T800//

Excellence in Radio
Communications

T800//

Receiver

T800//

Line
level

Supply

Monitor

Volume

Monitor

Mute

Off

On

Gating

Sensitivity

Gate

Exciter

Line

Sensitivity

Supply

On

Microphone

Carrier

T800// T800//

Power

Low forward power

High reverse power

Supply

Power Amplifier

T800//

Power Supply

Power

On

Standby

Overload

OPTIONAL

TRANSMITTER

OPTIONAL

BLANK
PANEL

FAN (OPTIONAL)

1X800-90-0000 POWER RAIL (STANDARD)

SECTION 4

REFERENCE

SECTION 4
SECTION 4
SECTION 4

SECTION 8

SECTION 3

SECTION 4
SECTION 8

ITEMS SUPPLIED AS STANDARD

PART NUMBER DESCRIPTION

1T800-22-0004 RACK, FRAME ONLY, ASSEMBLED

QTY

1T800-41-0002 DOUBLE GUIDE KIT

1T800-45-0000 GUIDE PA 50W KIT
1T800-44-0000 T800 PS GUIDE KIT
1T800-15-0000 SPEAKER / PROGRAM PANEL

1T800-50-0000 BACKPLANE

1T800-40-0000 FIXING KIT ONLY
1T800-40-0001 BLANKING BRACKET / FRONT PANEL

1T800-43-0001 GUIDE KIT T1500/300 SINGLE 'D'

1T800-60-0000 PERSONALITY BOARD

SECTION 4

SECTION 5
SECTION 6

EARTH

STUD

FUSE

TB1

OUTPUT

ONLY 13.8V

MAX

2 AMPS

PA ReceiverExciter

Rx/Tx MON

T818-01-0000

T800-50-0000

T800-60-0000

Power
Supply

Output

13.8V
25A
Max.

+

-

1
2
3
4
5

Speaker

Panel

FAN (OPTIONAL)

REFER TO SECTION 3

OF THE

REFERENCE GUIDE

FOR

POWER RAIL OPTIONS

M800RACK-00-100 Section 2

Copyright TEL 30/8/99

T800-22-0x21

A single 25 Watt repeater or base station channel rack to accommodate an Rx/Tx
Monitor and rack mounted circuit breaker for protection on the DC power input.

Operational Characteristics

•

Single channel

•

25W output only

•

Speaker / Programming panel

•

Panel circuit breaker

•

DC line fuse

•

Earth stud

•

Backplane interface

Power Supply Options

•

x = 0 AC only Not Available

•

x = 1 External DC only

•

x = 2 AC and External DC Not Available

•

x = 3 AC and Battery Not Available

•

x = 4 External DC and Battery

•

x = 5 AC and External DC and Battery Not Available

Configuration Options

•

Channel Panel

•

Duplexer

•

Coaxial Relay

•

Fans - single or double

•

Interfaces to Changeover Module TA703-00-xxxx using TA703-11-0011

installation kit

•

microphone

Mechanical Characteristics

•

5 Rack Units x 19” rack to house up to 7 modules

•

Size

Height - 222mm
Width - 482mm
Depth - 322mm plus 50mm clearance space

•

Weight – (rackframe with modules shown)

10.35kg

NOTE:

This product offers the versatility of fitting personality boards to provide
customised solutions for specific requirements.
Refer to RSD for design and build of personality boards.

Rack “Items Supplied as Standard” does not include modules other than those listed
on the drawing.

T A I T

Radio Communications
Christchurch
New Zealand

DRAWING:

T800-22-0x21 RACKFRAME

TITLE:

RACK, SNGL<25W, (MONITOR)

Drawn DateChecked

AMM 22/10/98ABB

AMM 25/8/99ABB

AMM 14/12/98ABB

AMM 18/3/99ABB

AMM 29/11/99ABB

Version

1

4

2

3

5

Original

Drg No changed, Ref added

Change of Title

Parts list added

Drg name changed

FRONT VIEW

REAR VIEW

Receiver

T800//

Line
level

Supply

Monitor

Volume

Monitor

Mute

Off

On

Gating

Sensitivity

Gate

OPTIONAL

DUPLEXER

OPTIONAL

CHANNEL

PANEL

Excellence in Radio
Communications

T800//

Rx/Tx Monitor

T800//

Supply

Volume

Volts
Rx Signal
Rx Line
Tx Line
Fwd Pwr
Rev Pwr

Off

Speaker Panel

T800//

Excellence in Radio
Communications

T800//

Transmitter

Line

Sensitivity

Supply

On

Microphone

Carrier

T800// T800//

Circuit Breaker

On

1

0

Off

Supply

12V

1X800-22-0121 POWER RAIL (STANDARD)

SECTION 5

SECTION 3

ITEMS SUPPLIED AS STANDARD

PART NUMBER DESCRIPTION

1T800-22-0004 RACK, FRAME ONLY, ASSEMBLED

QTY

1T800-41-0002 DOUBLE GUIDE KIT
1T800-43-0001 GUIDE KIT T1500/300 SINGLE 'D'

1T800-15-0000 SPEAKER / PROGRAM PANEL

1T800-50-0000 BACKPLANE
1T800-60-0000 PERSONALITY BOARD

1T800-17-0010 PANEL CIRCUIT BREAKER WITH 10AMP SWITCH

1T800-45-0000 GUIDE PA 50W KIT

1T800-40-0000 FIXING KIT ONLY
1T800-40-0001 BLANKING BRACKET / FRONT PANEL

1316-06615-00 BLANKING FRONT PANEL ONLY

SECTION 4

REFERENCE

SECTION 4
SECTION 4
SECTION 4
SECTION 8
SECTION 4
SECTION 8

SECTION 6

SECTION 8

SECTION 8

Rx/Tx MON

T818-01-0000

Circuit

Breaker

ReceiverTransmitter

T800-50-0000

T800-60-0000

Speaker

Panel

EARTH

STUD

DC INPUT

TB1

OUTPUT

ONLY 13.8V

MAX

2 AMPS

REFER TO SECTION 3

OF THE

REFERENCE GUIDE

FOR

POWER RAIL OPTIONS

M800RACK-00-100 Section 2

Copyright TEL 30/8/99

T800-22-0x22

A single 50 Watt repeater or base station channel rack to accommodate an Rx/Tx
Monitor and rack mounted circuit breaker for protection on the DC power input.

Operational Characteristics

•

Single channel

•

50W output only

•

Speaker / Programming panel

•

Panel circuit breaker

•

DC line fuse

•

Earth stud

•

Backplane interface

Power Supply Options

•

x = 0 AC only Not Available

•

x = 1 External DC only

•

x = 2 AC and External DC Not Available

•

x = 3 AC and Battery Not Available

•

x = 4 External DC and Battery

•

x = 5 AC and External DC and Battery Not Available

Configuration Options

•

Channel Panel

•

Duplexer

•

Coaxial Relay

•

Fans - single or double

•

Interfaces to Changeover Module TA703-00-xxxx using TA703-11-0011

installation kit

•

microphone

Mechanical Characteristics

•

5 Rack Units x 19” rack to house up to 7 modules

•

Size

Height - 222mm
Width - 482mm
Depth - 322mm plus 50mm clearance space

•

Weight – (rackframe with modules shown)

14.1kg

NOTE:

This product offers the versatility of fitting personality boards to provide
customised solutions for specific requirements.
Refer to RSD for design and build of personality boards.

Rack “Items Supplied as Standard” does not include modules other than those listed
on the drawing.

T A I T

Radio Communications
Christchurch
New Zealand

DRAWING:

T800-22-0x22 RACKFRAME

TITLE:

RACK, SNGL<=50W, (MONITOR)

Drawn DateChecked

AMM 22/10/98ABB

AMM 25/8/99ABB

AMM 14/12/98ABB

AMM 8/3/99ABB

AMM 29/11/99ABB

Version

1

4

2

3

5

Original

Drg No changed, Ref added

Change of Title

Parts list added

Drg name changed

FRONT VIEW

REAR VIEW

OPTIONAL

DUPLEXER

OPTIONAL

CHANNEL

PANEL

Rx/Tx Monitor

T800//

Supply

Volume

Volts
Rx Signal
Rx Line
Tx Line
Fwd Pwr
Rev Pwr

Off

Speaker Panel

T800//

Excellence in Radio
Communications

T800// T800//

Circuit Breaker

On

1

0

Off

Supply

12V

Receiver

T800//

Line
level

Supply

Monitor

Volume

Monitor

Mute

Off

On

Gating

Sensitivity

Gate

Exciter

Line

Sensitivity

Supply

On

Microphone

Carrier

T800// T800//

Power

Low forward power

High reverse power

Supply

Power Amplifier

1

SECTION 4

REFERENCE

SECTION 4
SECTION 4
SECTION 4
SECTION 8

SECTION 6
SECTION 3

SECTION 4
SECTION 8
SECTION 8
SECTION 5

1X800-22-0122 POWER RAIL (STANDARD)

ITEMS SUPPLIED AS STANDARD

PART NUMBER DESCRIPTION

1T800-22-0004 RACK, FRAME ONLY, ASSEMBLED

QTY

1T800-41-0002 DOUBLE GUIDE KIT

1T800-45-0000 GUIDE PA 50W KIT
1T800-15-0000 SPEAKER / PROGRAM PANEL

1T800-50-0000 BACKPLANE

1T800-40-0000 FIXING KIT ONLY
1T800-40-0001 BLANKING BRACKET / FRONT PANEL

1T800-43-0001 GUIDE KIT T1500/300 SINGLE 'D'

1T800-60-0000 PERSONALITY BOARD

T800-17-0020 PANEL CIRCUIT BREAKER WITH 20AMP SWITCH

EARTH

STUD

DC INPUT

TB1

OUTPUT

ONLY 13.8V

MAX

2 AMPS

PA ReceiverExciter

Rx/Tx MON

T818-01-0000

Circuit

Breaker

T800-50-0000

T800-60-0000

Speaker

Panel

FAN (OPTIONAL)

REFER TO SECTION 3

OF THE

REFERENCE GUIDE

FOR

POWER RAIL OPTIONS

FAN (OPTIONAL)

M800RACK-00-100 Section 2

Copyright TEL 30/8/99

T800-22-0x23

A single channel rack with 50 Watt maximum output, alarm outputs and AC power
supply.

Operational Characteristics

•

Single channel

•

Up to 50W output

•

Speaker / Programming panel

•

Alarm Panel

•

DC line fuse

•

Earth stud

•

Backplane interface

Power Supply Options

•

x = 0 AC only

•

x = 1 External DC only

•

x = 2 AC and External DC

•

x = 3 AC and Battery

•

x = 4 External DC and Battery

•

x = 5 AC and External DC and Battery

Configuration Options

•

Channel Panel

•

Duplexer

•

Coaxial Relay

•

Fans - single or double

•

Interfaces to Changeover Module TA703-00-xxxx using TA703-11-0011

installation kit

•

microphone

•

DC converter

Mechanical Characteristics

•

5 Rack Units x 19” rack to house up to 7 modules

•

Size

Height - 222mm
Width - 482mm
Depth - 322mm plus 50mm clearance space

•

Weight – (rackframe with modules shown)

25W - 12.1kg
50W - 15.85kg

NOTE:

This product offers the versatility of fitting personality boards to provide
customised solutions for specific requirements.
Refer to RSD for design and build of personality boards.

Rack “Items Supplied as Standard” does not include modules other than those listed
on the drawing.

T A I T

Radio Communications
Christchurch
New Zealand

DRAWING:

T800-22-0x23 RACKFRAME

TITLE:

RACK, SNGL<100W, (ALARMS 0V)

Drawn DateChecked

AMM 15/2/99ABB

AMM 29/11/99ABB

AMM 30/3/99ABB

AMM 25/8/99ABB

Version

1

4

2

3

Original

Drg name changed

Change personality board

Drg No changed, Ref added

FRONT VIEW

REAR VIEW

Receiver

T800//

Line
level

Supply

Monitor
Volume

Monitor

Mute

Off
On

Gating

Sensitivity

Gate

Excellence in Radio
Communications

T800//

Speaker Panel

T800// T800//

Power Supply

Power

On

Standby

Overload

Exciter

Line

Sensitivity

Supply

On

Microphone

Carrier

T800// T800//

Power

Low forward power

High reverse power

Supply

Power Amplifier

T800//

Alarm Panel

Power

PSU Fail

Forward

Test

Batt Fail

Forward

Reflected

Alarm#1

Alarm#2

Alarm#3

Alarm#4

OPTIONAL

BLANK

OPTIONAL

DUPLEXER

OPTIONAL

CH/PNL

FAN (OPTIONAL)

OPTIONAL

TRANSMITTER

OPTIONAL

BLANK

1X800-93-0000 POWER RAIL (STANDARD)

SECTION 4

REFERENCE

SECTION 4
SECTION 4
SECTION 4

SECTION 8

SECTION 5

SECTION 3

SECTION 4
SECTION 8

1T800-50-0000 BACKPLANE

ITEMS SUPPLIED AS STANDARD

PART NUMBER DESCRIPTION

1T800-24-0004 RACK, FRAME ONLY, ASSEMBLED

QTY

1T800-41-0002 DOUBLE GUIDE KIT
1T800-45-0000 GUIDE PA 50W KIT

1T800-15-0000 SPEAKER/PROGRAM PANEL
1T800-40-0000 FIXING KIT ONLY
1T800-40-0001 BLANKING BRACKET / F-PNL KIT

1T800-43-0000 GUIDE KIT T1500/300
1T800-44-0000 T800 PS GUIDE KIT

1T800-60-0002 PERSONALITY BOARD + CH/PNL + ALARMS (0V)

SECTION 4

SECTION 6

EARTH

STUD

BATTERY
BACK-UP

FUSE

TB1

DIODE

PACK

OUTPUT

ONLY 13.8V

MAX

2 AMPS

Power

Supply

Output

13.8V
25A
Max.

+

-

1
2
3
4
5

Receiver

Transmitter

or Exciter

T800-60-0002

Personality

Board

Alarm

PA

FAN

(OPTIONAL)

T800-50-0000

Speaker

Panel

REFER TO SECTION 3

OF THE

REFERENCE GUIDE

FOR

POWER RAIL OPTIONS

M800RACK-00-100 Section 2

Copyright TEL 30/8/99

T800-22-0x24

A single channel rack with 50 Watt maximum output, alarm outputs (LO) and AC
power supply.

Operational Characteristics

•

Single channel

•

Up to 50W output

•

Speaker / Programming panel

•

Alarm Panel

•

DC line fuse

•

Earth stud

•

Backplane interface

Power Supply Options

•

x = 0 AC only

•

x = 1 External DC only

•

x = 2 AC and External DC

•

x = 3 AC and Battery

•

x = 4 External DC and Battery

•

x = 5 AC and External DC and Battery

Configuration Options

•

Channel Panel

•

Duplexer

•

Coaxial Relay

•

Fans - single or double

•

Interfaces to Changeover Module TA703-00-xxxx using TA703-11-0011

installation kit

•

microphone

•

DC converter

Mechanical Characteristics

•

5 Rack Units x 19” rack to house up to 7 modules

•

Size

Height - 222mm
Width - 482mm
Depth - 322mm plus 50mm clearance space

•

Weight – (rackframe with modules shown)

25W - 12.1kg
50W - 15.85kg

NOTE:

This product offers the versatility of fitting personality boards to provide
customised solutions for specific requirements.
Refer to RSD for design and build of personality boards.

Rack “Items Supplied as Standard” does not include modules other than those listed
on the drawing.

T A I T

Radio Communications
Christchurch
New Zealand

DRAWING:

T800-22-0x24 RACKFRAME

TITLE:

RACK, SNGL<100W, (ALARMS LO)

Drawn DateChecked

AMM 7/9/99ABB

AMM 29/11/99ABB

Version

12Original

Drg name changed

FRONT VIEW

REAR VIEW

Receiver

T800//

Line
level

Supply

Monitor
Volume

Monitor

Mute

Off
On

Gating

Sensitivity

Gate

Excellence in Radio
Communications

T800//

Speaker Panel

T800// T800//

Power Supply

Power

On

Standby

Overload

Exciter

Line

Sensitivity

Supply

On

Microphone

Carrier

T800// T800//

Power

Low forward power

High reverse power

Supply

Power Amplifier

T800//

Alarm Panel

Power

PSU Fail

Forward

Test

Batt Fail

Forward

Reflected

Alarm#1

Alarm#2

Alarm#3

Alarm#4

OPTIONAL

BLANK

OPTIONAL

DUPLEXER

OPTIONAL

CH/PNL

FAN (OPTIONAL)

OPTIONAL

TRANSMITTER

OPTIONAL

BLANK

1X800-93-0000 POWER RAIL (STANDARD)

SECTION 4

REFERENCE

SECTION 4
SECTION 4
SECTION 4

SECTION 8

SECTION 5

SECTION 3

SECTION 4
SECTION 8

1T800-50-0000 BACKPLANE

ITEMS SUPPLIED AS STANDARD

PART NUMBER DESCRIPTION

1T800-24-0004 RACK, FRAME ONLY, ASSEMBLED

QTY

1T800-41-0002 DOUBLE GUIDE KIT
1T800-45-0000 GUIDE PA 50W KIT

1T800-15-0000 SPEAKER/PROGRAM PANEL
1T800-40-0000 FIXING KIT ONLY
1T800-40-0001 BLANKING BRACKET / F-PNL KIT

1T800-43-0000 GUIDE KIT T1500/300
1T800-44-0000 T800 PS GUIDE KIT

1T800-60-0001 PERSONALITY BOARD + CH/PNL + ALARMS (LO)

SECTION 4

SECTION 6

EARTH

STUD

BATTERY
BACK-UP

FUSE

TB1

DIODE

PACK

OUTPUT

ONLY 13.8V

MAX

2 AMPS

Power

Supply

Output

13.8V
25A
Max.

+

-

1
2
3
4
5

Receiver

Transmitter

or Exciter

T800-60-0001

Personality

Board

Alarm

PA

FAN

(OPTIONAL)

T800-50-0000

Speaker

Panel

REFER TO SECTION 3

OF THE

REFERENCE GUIDE

FOR

POWER RAIL OPTIONS

M800RACK-00-100 Section 2

Copyright TEL 30/8/99

T800-23-0x00

A single channel rack with 25 Watt maximum output mounted in a 2RU Slimline
configuration for use in DC situations.

Operational Characteristics

•

Single channel

•

Up to 25W output

•

Speaker / Programming Port

Power Supply Options

•

x = 0 AC only Not Available

(see T800-23-0x01)

•

x = 1 External DC only

•

x = 2 AC and External DC Not Available

•

x = 3 AC and Battery Not Available

•

x = 4 External DC and Battery

•

x = 5 AC and External DC and Battery Not Available

Configuration Options

•

Coaxial Relay

•

Microphone

Mechanical Characteristics

•

2 Rack Units x 19” rack to house up to 7 modules

•

Size

Height - 89mm
Width - 482mm
Depth - 322mm plus 50mm clearance space

•

Weight – (rackframe with modules shown)

25W – 3.9kg

This configuration includes Receiver and Transmitter modules. (to be specified when
ordering)

T A I T

Radio Communications
Christchurch
New Zealand

DRAWING:

T800-23-0x00

TITLE:

SLIMLINE 25W DC

Drawn DateChecked

AMM 20/9/99ABB

Version

1 Original

FRONT VIEW

REAR VIEW

ReceiverTransmitter

TB

Receiver

Line
Level

Supply

Monitor

Volume

Monitor

Gating

Sensitivity

Gate

On Off

T800//

Transmitter

Line

Sensitivity

Supply

Exciter Out

On

MicrophoneCarrier

T800II Slimline

ITEMS SUPPLIED AS STANDARD

PART NUMBER DESCRIPTION

1T800-23-0000 SLIMLINE ASSEMBLY KIT + CABLES

QTY

1T8n5-nn-nnnn RECEIVER
1T8n6-nn-nnnn TRANSMITTER

SECTION 4

REFERENCE

SECTION 8
SECTION 8

M800RACK-00-100 Section 2

Copyright TEL 30/8/99

T800-23-0x01

A single channel rack with 25 Watt maximum output mounted in a 2RU Slimline
configuration, with an AC power supply.

Operational Characteristics

•

Single channel

•

Up to 25W output

•

Speaker / Programming Port

Power Supply Options

•

x = 0 AC only

•

x = 1 External DC only Not Available

(see T800-23-0x00)

•

x = 2 AC and External DC

•

x = 3 AC and Battery

•

x = 4 External DC and Battery Not Available

•

x = 5 AC and External DC and Battery

Configuration Options

•

Coaxial Relay

•

Microphone

Mechanical Characteristics

•

2 Rack Units x 19” rack to house up to 7 modules

•

Size

Height - 89mm
Width - 482mm
Depth - 322mm plus 50mm clearance space

•

Weight – (rackframe with modules shown)

25W – 8.55kg

This configuration includes Receiver and Transmitter modules. (to be specified when
ordering)
.

T A I T

Radio Communications
Christchurch
New Zealand

DRAWING:

T800-23-0x01

TITLE:

SLIMLINE 25W AC

Drawn DateChecked

AMM 20/9/99ABB

Version

1 Original

FRONT VIEW

REAR VIEW

ReceiverTransmitter

Power Suppl

y

TB

Receiver

Line
Level

Supply

Monitor

Volume

Monitor

Gating

Sensitivity

Gate

On Off

T800//

Transmitter

Line

Sensitivity

Supply

Exciter Out

On

MicrophoneCarrier

T800II Slimline

ITEMS SUPPLIED AS STANDARD

PART NUMBER DESCRIPTION

1T800-23-0001 SLIMLINE ASSEMBLY KIT + CABLES + POWER SUPPLY

QTY

1T8n5-nn-nnnn RECEIVER
1T8n6-nn-nnnn TRANSMITTER

SECTION 4

REFERENCE

SECTION 8
SECTION 8

M800RACK-00-100 Section 2

Copyright TEL 30/8/99

T800-25-0000

A single 25W channel, housed in a portable case with sealed lead acid batteries.

Operational Characteristics

•

Single channel

•

Up to 25W output

•

DC only operation - Batteries and external DC supply input

•

Speaker / Programming panel

•

DC line fuse

•

Backplane interface

•

Battery Isolation Switch

Configuration Options

•

Channel Panel

•

Duplexer

•

Coaxial Relay

•

Antenna

Mechanical Characteristics

•

Portable case to house up to 4 modules

•

Top Mounting Duplexer Tray

•

Size

Case Only with Handles and Connectors
Height - 242mm 305mm
Width - 255mm 300mm
Depth - 460mm 460mm

•

Weight – (rackframe with modules shown)

15.85kg

CAUTION: If operating above 15 Watts, front and rear covers must be removed.

Rack “Items Supplied as Standard” does not include modules other than those listed
on the drawing.

T A I T

Radio Communications
Christchurch
New Zealand

DRAWING:

T800-25-0000

TITLE:

T800-25-0000 PORTABLE

Drawn DateChecked

AMM 4/3/99AB B

AMM 26/8/99ABB

AMM 2/6/99AB B

AMM 30/6/99ABB

Version

1

4

2

3

Original

Reference added

Diode pack alignment corrected

Battery details added

FRONT VIEW

REAR VIEW

Receiver

T800//

Line

level

Monitor
Volume

Monitor

Mute

Off
On

Gating

Sensitivity

Gate

Supply

Transmitter

Line

Sensitivity

Supply

On

Microphone

Carrier

T800// T800//

Speaker Panel

T800//

T8n5 -nn-0200 T8n6 -nn-0200

T800-15-0000

SPKR/PROG PNL

or
TA087-01-0000
100 CHANNEL

CHANNEL PANEL

or
TA387-01-0000

10 CHANNEL

CHANNEL PANEL

EXTERNAL DC BATTERY OPERATION

TALK THROUGH

BASE STATION REPEATER

FUSE

10A

T800-50-0001

DC

ON

OFF

Duplexer mounted behind

REFERENCE

SECTION 4
SECTION 4
SECTION 4
SECTION 8

SECTION 5

SECTION 4

1W800-25-0000 WIRING LIST T800-25-0000

ITEMS SUPPLIED AS STANDARD

PART NUMBER DESCRIPTION

1T991-05-0100 CASE, PORTABLE REPEATER - 0100 VERSION

QTY

1T800-41-0002 DOUBLE GUIDE KIT
1T800-40-0001 BLANK PANEL AND FIXING KIT
1T800-15-0000 SPEAKER / PROGRAM PANEL
1T800-40-0000 FIXING KIT ONLY
1T800-50-0001 BACKPLANE

1X800-25-0000 STANDARD LOOM ASSEMBLY

2290-00010-48 BATTERY SEALED LEAD ACID 12V 6.5A

M800RACK-00-100 Section 2

Copyright TEL 30/8/99

T800-25-0001

A single 25W channel, housed in a portable case with sealed lead acid batteries.
This unit can use an external AC power source.

Operational Characteristics

•

Single channel

•

Up to 25W output

•

AC and DC operation - Batteries, external AC and DC supply input

•

Speaker / Programming panel

•

DC line fuse

•

Backplane interface

•

Battery Isolation Switch

•

Talk Through Switch

Configuration Options

•

Channel Panel

•

Duplexer

•

Coaxial Relay

•

Antenna

Mechanical Characteristics

•

Portable case to house up to 4 modules

•

Top Mounting Duplexer Tray

•

Size

Case Only with Handles and Connectors
Height - 242mm 305mm
Width - 255mm 300mm
Depth - 460mm 460mm

•

Weight – (rackframe with modules shown)

18.3kg

CAUTION: If operating above 15 Watts, front and rear covers must be removed.

Rack “Items Supplied as Standard” does not include modules other than those listed
on the drawing.

T A I T

Radio Communications
Christchurch
New Zealand

DRAWING:

T800-25-0001

TITLE:

T800-25-0001 PORTABLE

Drawn DateChecked

AMM 5/3/99AB B

AMM 26/8/99ABB

AMM 1/6/99AB B

AMM 30/6/99ABB

Version

1

4

2

3

Original

Reference added

Diode pack alignment corrected

Battery details added

FRONT VIEW

REAR VIEW

Receiver

T800//

Line

level

Monitor
Volume

Monitor

Mute

Off
On

Gating

Sensitivity

Gate

Supply

Transmitter

Line

Sensitivity

Supply

On

Microphone

Carrier

T800//

Speaker Panel

T800//

T8n5 -nn-0200 T8n6 -nn-0200

T800-15-0000

SPKR/PROG PNL

or
TA087-01-0000
100 CHANNEL

CHANNEL PANEL

or
TA387-01-0000

10 CHANNEL

CHANNEL PANEL

T800//

Power Supply

Power

On

Standby

Overload

EXTERNAL DC BATTERY OPERATION

TALK THROUGH

BASE STATION REPEATER

Output

13.8V
25A
Max.

+

-

1
2
3
4
5

FUSE

10A

T800-50-0001

DC

and

SIGS

ON

OFF

Duplexer mounted behind

AC

I/P

REFERENCE

SECTION 4
SECTION 4
SECTION 4
SECTION 8

SECTION 5

SECTION 4

1W800-25-0000 WIRING LIST T800-25-0000

ITEMS SUPPLIED AS STANDARD

PART NUMBER DESCRIPTION

1T991-05-0100 CASE, PORTABLE REPEATER - 0100 VERSION

QTY

1T800-41-0002 DOUBLE GUIDE KIT
1T800-44-0000 T800 PS GUIDE KIT
1T800-15-0000 SPEAKER / PROGRAM PANEL
1T800-40-0000 FIXING KIT ONLY
1T800-50-0001 BACKPLANE

1X800-25-0000 STANDARD LOOM ASSEMBLY

2290-00010-48 BATTERY SEALED LEAD ACID 12V 6.5A

M800RACK-00-100 Section 2

Copyright TEL 30/8/99

T800-25-0002

A single channel with up to 50W output, housed in a portable case with no batteries.
This unit can use external AC or DC power source.

Operational Characteristics

•

Single channel

•

Up to 50W output

•

AC and DC operation - External AC and DC supply input

•

DC line fuse

•

Backplane interface

•

Battery Isolation Switch

•

Talk Through Switch

Configuration Options

•

Channel Panel

•

Duplexer

•

Coaxial Relay

•

Antenna

Mechanical Characteristics

•

Portable case to house up to 4 modules

•

Top Mounting Duplexer Tray

•

Size

Case Only with Handles and Connectors
Height - 242mm 305mm
Width - 255mm 300mm
Depth - 460mm 460mm

•

Weight – (rackframe with modules shown)

25W - 12.55kg
50W - 15.9kg

CAUTION: If operating above 15 Watts, front and rear covers must be removed.

Rack “Items Supplied as Standard” does not include modules other than those listed
on the drawing.

T A I T

Radio Communications
Christchurch
New Zealand

DRAWING:

T800-25-0002

TITLE:

PORTABLE REPEATER <=50W

X-DC + AC (NO BATT)

Drawn DateChecked

AMM 4/6/99AB B

AMM 26/8/99ABB

Version

12Original

Reference added

FRONT VIEW

REAR VIEW

Receiver

T800//

Line

level

Monitor
Volume

Monitor

Mute

Off
On

Gating

Sensitivity

Gate

Supply

OPTIONAL BLANK

PANEL

or

OPTIONS PANEL

OPTIONAL

TRANSMITTER

T800-15-0000

SPKR/PROG PNL

or

TA087-01-0000

100 CHANNEL

CHANNEL PANEL

or

TA387-01-0000

10 CHANNEL

CHANNEL PANEL

T800//

Power Supply

Power

On

Standby

Overload

EXTERNAL DC BATTERY OPERATION

TALK THROUGH

BASE STATION REPEATER

Exciter

Line

Sensitivity

Supply

On

Microphone

Carrier

T800// T800//

Power

Low forward power

High reverse power

Supply

Power Amplifier

T800-15-0000

SPKR/PROG PNL

or

TA087-01-0000

100 CHANNEL

CHANNEL PANEL

or

TA387-01-0000

10 CHANNEL

CHANNEL PANEL

Output

13.8V
25A
Max.

+

-

1
2
3
4
5

FUSE

10A

T800-50-0001

DC

I/P

Duplexer mounted behind

AC

I/P

DR1

DR2

REFERENCE

SECTION 4
SECTION 4
SECTION 4

SECTION 5

SECTION 4

1W800-25-0002 WIRING LIST T800-25-0002

ITEMS SUPPLIED AS STANDARD

PART NUMBER DESCRIPTION

1T991-05-0100 CASE, PORTABLE REPEATER - 0100 VERSION

QTY

1T800-41-0002 DOUBLE GUIDE KIT
1T800-44-0000 T800 PS GUIDE KIT
1T800-45-0000 PA (50W) GUIDE KIT
1T800-50-0001 BACKPLANE
1X800-25-0002 RACK KIT

M800RACK-00-100 Section 2

Copyright TEL 30/8/99

T800-27-0x00

A dual channel rack with 25 Watt per channel maximum output and Tone Remote /
Alarm outputs.

Operational Characteristics

•

Dual channel

•

Up to 25W output

•

Speaker / Programming panel

•

Remote / Alarm Panel

•

DC line fuse

•

Earth stud

•

Backplane interface

Power Supply Options

•

x = 0 AC only

•

x = 1 External DC only

•

x = 2 AC and External DC

•

x = 3 AC and Battery

•

x = 4 External DC and Battery

•

x = 5 AC and External DC and Battery

Configuration Options

•

Coaxial Relay

•

Fans - single or double

•

Interfaces to Changeover Module TA703-00-xxxx using TA703-11-0011

installation kit

•

microphone

•

DC converter

Mechanical Characteristics

•

5 Rack Units x 19” rack to house up to 7 modules

•

Size

Height - 222mm
Width - 482mm
Depth - 322mm plus 50mm clearance space

•

Weight – (rackframe with modules shown)

25W - 20.25kg

Rack “Items Supplied as Standard” does not include modules other than those listed
on the drawing.

T A I T

Radio Communications
Christchurch
New Zealand

DRAWING:

T800-27-0x00 RACKFRAME

TITLE:

RACK, DUAL 2X25W, (REMOTE

Drawn DateChecked

AMM 20/10/98ABB

AMM 26/8/99ABB

AMM 26/11/99ABB

Version

1

4

2

3

Original

Drg No changed, Ref added

Drg name changed

FRONT VIEW

REAR VIEW

Receiver

T800//

Line

level

Supply

Monitor
Volume

Monitor

Mute

Off
On

Gating

Sensitivity

Gate

T800//

Power Supply

Power

On

Standby

Overload

Receiver

T800//

Line
level

Supply

Monitor
Volume

Monitor

Mute

Off
On

Gating

Sensitivity

Gate

Transmitter

Line

Sensitivity

Supply

On

Microphone

Carrier

T800//

Transmitter

Line

Sensitivity

Supply

On

Microphone

Carrier

T800//

Remote / Alarm

T800//

Talk Through

Base Station

Monitor On / Off

Monitor
Volume

Mode Toggle

Rev Power

Aux 0

Fwd Power

Aux 1

Low Battery

Aux 2

Line Fail

Aux 3

Programming

Port

Clear
Alarms

Test
(3 sec)

Remote / Alarm

T800//

Talk Through

Base Station

Monitor On / Off

Monitor
Volume

Mode Toggle

Rev Power

Aux 0

Fwd Power

Aux 1

Low Battery

Aux 2

Line Fail

Aux 3

Programming

Port

Clear
Alarms

Test
(3 sec)

OPTIONAL

BLANK

1

QTY

2
1
2
1

SECTION 4

REFERENCE

SECTION 4
SECTION 4
SECTION 5
SECTION 3

ITEMS SUPPLIED AS STANDARD

PART NUMBER DESCRIPTION

T800-11-0004 RACK, FRAME ONLY, ASSEMBLED 2 BATT BACK-UP
T800-41-0003 TRIPLE GUIDE KIT
T800-44-0000 T800 PS GUIDE KIT
T800-54-0000 BACKPLANE RACK REMOTE
X800-93-0001 POWER RAIL (STANDARD)

Power

Supply

Output

13.8V
25A
Max.

+

-

1
2
3
4
5

ReceiverTransmitter Remote

T800-54-0000

DR2

ReceiverTransmitter Remote

T800-54-0000

DR1

PLUG SKTPLUG SKT

EARTH

STUD

BATTERY
BACK-UP

FUSE

TB1

DIODE

PACK

OUTPUT

ONLY 13.8V

MAX

2 AMPS

FUSE

REFER TO SECTION 3

OF THE

REFERENCE GUIDE

FOR

POWER RAIL OPTIONS

M800RACK-00-100 Section 2

Copyright TEL 30/8/99

T800-27-0x01

A single channel rack with 100 Watt maximum output, Tone Remote / Alarm
outputs and AC power supply.

Operational Characteristics

•

Single channel

•

Up to 100W output

•

Speaker / Programming panel

•

Remote / Alarm Panel

•

DC line fuse

•

Earth stud

•

Backplane interface

Power Supply Options

•

x = 0 AC only

•

x = 1 External DC only

•

x = 2 AC and External DC

•

x = 3 AC and Battery

•

x = 4 External DC and Battery

•

x = 5 AC and External DC and Battery

Configuration Options

•

Duplexer

•

Coaxial Relay

•

Fans - single or double

•

Interfaces to Changeover Module TA703-00-xxxx using TA703-11-0011

installation kit

•

microphone

•

DC converter

Mechanical Characteristics

•

5 Rack Units x 19” rack to house up to 7 modules

•

Size

Height - 222mm
Width - 482mm
Depth - 322mm plus 50mm clearance space

•

Weight – (rackframe with modules shown)

25W - 12.8kg
50W - 16.55kg
100W - 16.9kg

Rack “Items Supplied as Standard” does not include modules other than those listed
on the drawing.

T A I T

Radio Communications
Christchurch
New Zealand

DRAWING:

T800-27-0x01 RACKFRAME

TITLE:

RACK, SNGL<100W, (REMOTE

Drawn DateChecked

AMM 1/6/99ABB

AMM 26/8/99ABB

AMM 26/11/99ABB

Version

1

2

3

Original

Drg No changed, Ref added

Drg name changed

FRONT VIEW

REAR VIEW

T800//

Power Supply

Power

On

Standby

Overload

Receiver

T800//

Line
level

Supply

Monitor
Volume

Monitor

Mute

Off
On

Gating

Sensitivity

Gate

Exciter

Line

Sensitivity

Supply

On

Microphone

Carrier

T800//

Excellence in Radio
Communications

T800//

FAN (optional)

Excellence in Radio
Communications

T800//T800//

Power

Low forward power

High reverse power

Supply

Power Amplifier

OPTIONAL

TRANSMITTER

OPTIONAL

BLANK

OPTIONAL

DUPLEXER

Remote / Alarm

T800//

Talk Through

Base Station

Monitor On / Off

Monitor

Volume

Mode Toggle

Rev Power

Aux 0

Fwd Power

Aux 1

Low Battery

Aux 2

Line Fail

Aux 3

Programming

Port

Clear
Alarms

Test
(3 sec)

OPTIONAL

BLANK

1X800-90-0000 POWER RAIL (STANDARD)

SECTION 4

REFERENCE

SECTION 4
SECTION 4
SECTION 4

SECTION 5
SECTION 3

SECTION 8

ITEMS SUPPLIED AS STANDARD

PART NUMBER DESCRIPTION

1T800-24-0004 RACK, FRAME ONLY, ASSEMBLED

QTY

1T800-41-0003 GUIDE TRIPLE SERIESII KIT
1T800-44-0000 T800 PS GUIDE KIT
1T800-45-0000 GUIDE PA 50W SERIESII KIT

1X800-54-0000 T803-00-0000 BACKPLANE ASSEMBLY

2T800-40-0001 BLANKING BRACKET / FRONT PANEL

EARTH

STUD

FUSE

TB1

OUTPUT

ONLY 13.8V

MAX

2 AMPS

Power
Supply

Output

13.8V
25A
Max.

+

-

1
2
3
4
5

PA ReceiverExciter

FAN

Optional

Remote / Alarm

T800-54-0000

DR1

DR2

PLUG SKT

REFER TO SECTION 3

OF THE

REFERENCE GUIDE

FOR

POWER RAIL OPTIONS

M800RACK-00-100 Section 2

Copyright TEL 30/8/99

T800-28-0x00

A single channel rack with 100 Watt maximum output, and provision for a
High Stability Oscillator to enable the Paging function.

Operational Characteristics

•

Single channel - Paging

•

Up to 100W output

•

Speaker / Programming panel

•

High Stability Oscillator

•

DC line fuse

•

Earth stud

•

Backplane interface

Power Supply Options

•

x = 0 AC only

•

x = 1 External DC only

•

x = 2 AC and External DC

•

x = 3 AC and Battery

•

x = 4 External DC and Battery

•

x = 5 AC and External DC and Battery

Configuration Options

•

Duplexer

•

Coaxial Relay

•

Fans - single or double

•

Interfaces to Changeover Module TA703-00-xxxx using TA703-11-0010

installation kit

•

microphone

•

DC converter

Mechanical Characteristics

•

5 Rack Units x 19” rack to house up to 7 modules

•

Size

Height - 222mm
Width - 482mm
Depth - 322mm plus 50mm clearance space

•

Weight – (rackframe with modules shown)

25W - 12.75kg
50W - 16.5kg
100W - 16.85kg

Rack “Items Supplied as Standard” does not include modules other than those listed
on the drawing.

T A I T

Radio Communications
Christchurch
New Zealand

DRAWING:

T800-28-0x00 RACKFRAME

TITLE:

RACK, SNGL<100W, (PAGING

Drawn DateChecked

AMM 2/6/99ABB

AMM 26/11/99ABB

AMM 30/6/99ABB

AMM 26/8/99ABB

Version

1

4

2

3

Original

Drg name changed

Speaker removed

Drg No changed, Ref added

FRONT VIEW

REAR VIEW

T800//

Power Supply

Power

On

Standby

Overload

Receiver

T800//

Line

level

Supply

Monitor
Volume

Monitor

Mute

Off
On

Gating

Sensitivity

Gate

Exciter

Line

Sensitivity

Supply

On

Microphone

Carrier

T800//

FAN (optional)

Excellence in Radio
Communications

T800//

HSO

T800//

Supply

12.8 MHz

Frequency

Adjust

10.0 MHz

T800//

Power

Low forward power

High reverse power

Supply

Power Amplifier

OPTIONAL

TRANSMITTER

OPTIONAL

BLANK

OPTIONAL

BLANK

OPTIONAL

BLANK

Excellence in Radio
Communications

T800//

OPTIONAL

TRANSMITTER

OPTIONAL

BLANK

1X800-90-0004 POWER RAIL (STANDARD)

SECTION 4

REFERENCE

SECTION 4
SECTION 4
SECTION 4

SECTION 5
SECTION 3

SECTION 8

ITEMS SUPPLIED AS STANDARD

PART NUMBER DESCRIPTION

1T800-24-0004 RACK, FRAME ONLY, ASSEMBLED

QTY

1T800-41-0003 GUIDE TRIPLE SERIESII KIT
1T800-44-0000 T800 PS GUIDE KIT
1T800-45-0000 GUIDE PA 50W SERIESII KIT

1T800-55-0000 BACKPLANE

2T800-40-0001 BLANKING BRACKET / FRONT PANEL

EARTH

STUD

FUSE

TB1

OUTPUT

ONLY 13.8V

MAX

2 AMPS

Power
Supply

Output

13.8V
25A
Max.

+

-

1
2
3
4
5

PA ReceiverExciter

FAN

Optional

HSO

T800-55-0000

DR1

DR2

PLUG

REFER TO SECTION 3

OF THE

REFERENCE GUIDE

FOR

POWER RAIL OPTIONS

M800RACK-00-100 Section 2

Copyright TEL 30/8/99

T800-29-0x00

A dual channel rack with 25 Watt maximum output, to interface to Fylde Trunking
Controller

Operational Characteristics

•

Dual channel

•

Up to 25W output

•

Speaker / Programming panel

•

DC line fuse

•

Earth stud

•

Backplane interface

Power Supply Options

•

x = 0 AC only

•

x = 1 External DC only

•

x = 2 AC and External DC

•

x = 3 AC and Battery

•

x = 4 External DC and Battery

•

x = 5 AC and External DC and Battery

Configuration Options

•

Fans - single or double

•

microphone

•

DC converter

Mechanical Characteristics

•

5 Rack Units x 19” rack to house up to 7 modules

•

Size

Height - 222mm
Width - 482mm
Depth - 322mm plus 50mm clearance space

•

Weight – (rackframe with modules shown)

25W - 16.05kg

Rack “Items Supplied as Standard” does not include modules other than those listed
on the drawing.

T A I T

Radio Communications
Christchurch
New Zealand

DRAWING:

T800-29-0x00 RACKFRAME

TITLE:

RACK, DUAL 2x25W, (FYLDE

Drawn DateChecked

AMM 2/8/99ABB

AMM 26/11/99ABB

Version

12Original

Drawing name changed

FRONT VIEW

REAR VIEW

Receiver

T800//

Line
level

Supply

Monitor
Volume

Monitor

Mute

Off
On

Gating

Sensitivity

Gate

Speaker Panel

T800//

RX 1 RX 2

O
F
F

O
F
F

Receiver

T800//

Line
level

Supply

Monitor
Volume

Monitor

Mute

Off

On

Gating

Sensitivity

Gate

Transmitter

Line

Sensitivity

Supply

On

Microphone

Carrier

T800//

Excellence in Radio
Communications

T800// T800//

Power Supply

Power

On

Standby

Overload

Transmitter

Line

Sensitivity

Supply

On

Microphone

Carrier

T800//

OPTIONAL

DUPLEXER

BEHIND SPK/PROG

PANEL

OPTIONAL

DUPLEXER

OPTIONAL

BLANK

ITEMS SUPPLIED AS STANDARD

PART NUMBER DESCRIPTION

1T800-22-0004 RACK, FRAME ONLY, ASSEMBLED

QTY

2T800-41-0002 DOUBLE GUIDE KIT
1T800-44-0000 T800 PS GUIDE KIT
1T800-15-0003 SPEAKER/PROGRAM PANEL WITH 3 POSITION SWITCH
1T800-40-0000 FIXING KIT ONLY
1T800-40-0001 BLANK PANEL AND FIXING KIT

1X800-90-0001

POWER RAIL (STANDARD)

2T800-57-0000 BACKPLANE (FYLDE)

EARTH

STUD

FUSE

TB1

OUTPUT

ONLY 13.8V

MAX

2 AMPS

FUSE

ReceiverTransmitter

T800-57-0000

Speaker

Panel

Power
Supply

Output

13.8V
25A
Max.

+

-

1
2
3
4
5

SK107

SK102 SK101

PL101

SK109

RV210RV211

SK201

ReceiverTransmitter

T800-57-0000

SK107

SK102 SK101

PL101

SK109

RV210RV211

SK201

REFER TO SECTION 3

OF THE

REFERENCE GUIDE

FOR

POWER RAIL OPTIONS

M800RACK-00-100 Section 2

Copyright TEL 30/8/99

T800-29-0x01

A single channel rack with 100 Watt maximum output, to interface to Fylde Trunking
Controller

Operational Characteristics

•

Single channel

•

Up to 100W output

•

Speaker / Programming panel

•

DC line fuse

•

Earth stud

•

Backplane interface

Power Supply Options

•

x = 0 AC only

•

x = 1 External DC only

•

x = 2 AC and External DC

•

x = 3 AC and Battery

•

x = 4 External DC and Battery

•

x = 5 AC and External DC and Battery

Configuration Options

•

Fans - single or double

•

microphone

•

DC converter

Mechanical Characteristics

•

5 Rack Units x 19” rack to house up to 7 modules

•

Size

Height - 222mm
Width - 482mm
Depth - 322mm plus 50mm clearance space

•

Weight – (rackframe with modules shown)

25W - 10.7kg
50W - 14.45kg
100W - 14.8kg

Rack “Items Supplied as Standard” does not include modules other than those listed
on the drawing.

T A I T

Radio Communications
Christchurch
New Zealand

DRAWING:

T800-29-0x01 RACKFRAME

TITLE:

RACK, SNGL <=100W, (FYLDE

Drawn DateChecked

AMM 2/8/99ABB

AMM 26/11/99ABB

Version

12Original

Drg name changed

FRONT VIEW

REAR VIEW

Receiver

T800//

Line
level

Supply

Monitor
Volume

Monitor

Mute

Off
On

Gating

Sensitivity

Gate

Excellence in Radio
Communications

T800// T800//

Power Supply

Power

On

Standby

Overload

OPTIONAL

BLANK

OPTIONAL

TRANSMITTER

FAN

(OPTIONAL)

Exciter

Line

Sensitivity

Supply

On

Microphone

Carrier

T800// T800//

Power

Low forward power

High reverse power

Supply

Power Amplifier

Excellence in Radio
Communications

T800//

Speaker Panel

T800//

OPTIONAL

DUPLEXER

OPTIONAL

BLANK

ITEMS SUPPLIED AS STANDARD

PART NUMBER DESCRIPTION

1T800-22-0004 RACK, FRAME ONLY, ASSEMBLED

QTY

1T800-41-0002 DOUBLE GUIDE KIT

1T800-44-0000 T800 PS GUIDE KIT
1T800-15-0000 SPEAKER/PROGRAM PANEL
1T800-40-0000 FIXING KIT ONLY
2T800-40-0001 BLANK PANEL AND FIXING KIT

1X800-90-0000 POWER RAIL (STANDARD)

1T800-57-0000 BACKPLANE (FYLDE)

1T800-45-0001 PA (100W) GUIDE KIT

EARTH

STUD

FUSE

TB1

OUTPUT

ONLY 13.8V

MAX

2 AMPS

PA ReceiverExciter

FAN

(OPTIONAL)

Speaker

Panel

Power

Supply

Output

13.8V
25A
Max.

+

-

1
2
3
4
5

T800-57-0000

SK107

SK102 SK101

PL101

SK108

RV210RV211

SK201

DR1

REFER TO SECTION 3

OF THE

REFERENCE GUIDE

FOR

POWER RAIL OPTIONS

M800RACK-00-100 Section 2

Copyright TEL 30/8/99

T800-29-0x02

A dual channel rack with 50 Watt maximum output, to interface to Fylde Trunking
Controller.

Operational Characteristics

•

Dual channel

•

Up to 50W output

•

Speaker / Programming panel

•

DC line fuse

•

Earth stud

•

Backplane interface

Power Supply Options

•

x = 0 AC only Not Available

•

x = 1 External DC only

•

x = 2 AC and External DC Not Available

•

x = 3 AC and Battery Not Available

•

x = 4 External DC and Battery

•

x = 5 AC and External DC and Battery Not Available

Configuration Options

•

Fans - single or double

•

microphone

•

DC converter

Mechanical Characteristics

•

5 Rack Units x 19” rack to house up to 7 modules

•

Size

Height - 222mm
Width - 482mm
Depth - 322mm plus 50mm clearance space

•

Weight – (rackframe with modules shown)

50W - 20.7kg

Rack “Items Supplied as Standard” does not include modules other than those listed
on the drawing.

T A I T

Radio Communications
Christchurch
New Zealand

DRAWING:

T800-29-0x02 RACKFRAME

TITLE:

RACK, DUAL 2x50W, (FYLDE

Drawn DateChecked

AMM 3/8/99AB B

AMM 31/8/99ABB

AMM 26/11/99AB B

Version

1

2

3

Original

Drg No changed, Ref added

Drg name changed

FRONT VIEW

REAR VIEW

Speaker Panel

T800//

RX 1 RX 2

O

F
F

O

F
F

Receiver

T800//

Line
level

Supply

Monitor
Volume

Monitor

Mute

Off
On

Gating

Sensitivity

Gate

FAN

(OPTIONAL)

FAN

(OPTIONAL)

T800//

Power

Low forward power

High reverse power

Supply

Power Amplifier Exciter

Line

Sensitivity

Supply

On

Microphone

Carrier

T800// T800//

Power

Low forward power

High reverse power

Supply

Power AmplifierReceiver

T800//

Line

level

Supply

Monitor
Volume

Monitor

Mute

Off
On

Gating

Sensitivity

Gate

Exciter

Line

Sensitivity

Supply

On

Microphone

Carrier

T800//

1X800-91-0002 POWER RAIL (STANDARD)

REFERENCE

SECTION 4
SECTION 4
SECTION 4
SECTION 8

SECTION 5
SECTION 3

SECTION 4

ITEMS SUPPLIED AS STANDARD

PART NUMBER DESCRIPTION

1T800-11-0004 RACK, FRAME ONLY, ASSEMBLED, 2 BATTERY BACK-UP

QTY

2T800-41-0002 DOUBLE GUIDE KIT
2T800-45-0000 PA (50W) GUIDE KIT
1T800-15-0003 SPEAKER/PROGRAM PANEL WITH 3 POSITION SWITCH
1T800-40-0000 FIXING KIT ONLY
2T800-57-0000 BACKPLANE (FYLDE)

EARTH

STUD

DC INPUT FUSE

TB1

OUTPUT

ONLY 13.8V

MAX

2 AMPS

FUSE

FAN (OPTIONAL)

FAN (OPTIONAL)

Speaker

Panel

Receiver

Exciter

T800-57-0000

SK107

SK102 SK101

PL101

SK108

RV210RV211

SK201

DR3

Receiver

PA Exciter

T800-57-0000

SK107

SK102 SK101

PL101

SK108

RV210RV211

SK201

DR2

DR1

PA

DR4

REFER TO SECTION 3

OF THE

REFERENCE GUIDE

FOR

POWER RAIL OPTIONS

T800 Series

II

Conventional Equipment

Reference Guide

Rack

Power Supply

Options

M800RACK-00-100 Section 3

Copyright TEL 30/8/99

Power Supply Options

This section details the Power Supply Options f o r T800 SeriesII Conventional
rackframes. The power rails have been standardised to allow versatility in the rack
applications.

Not all options are available on every rack. Please contact RSD if you are unsure of
the correct option.

Baan Codes

X800-90-0000RAIL<=100W,ACfor1supply
X800-91-0000RAIL<=100W,AC+X-DCfor1supply
X800-92-0000RAIL<=100W,ACfor1supply
X800-93-0000RAIL<=100W,AC+BATfor1supply
X800-94-0000RAIL<=100W,X-DC+BATfor1supply
X800-95-0000RAIL<=100W,AC+X-DC+BATfor1supply

X800-90-0001RAIL,2x25W,ACfor2supply
X800-91-0001RAIL,2x25W,AC+X-DCfor2supply
X800-92-0001RAIL,2x25W,ACfor2supply
X800-93-0001RAIL,2x25W,AC+BATfor2supply
X800-94-0001RAIL,2x25W,X-DC+BATfor2supply
X800-95-0001RAIL,2x25W,AC+X-DC+BATfor2supply

X800-90-0002RAIL,2x50W,ACfor2supply
X800-91-0002RAIL,2x50W,AC+X-DCfor2supply
X800-92-0002RAIL,2x50W,ACfor2supply
X800-93-0002RAIL,2x50W,AC+BATfor2supply
X800-94-0002RAIL,2x50W,X-DC+BATfor2supply
X800-95-0002RAIL,2x50W,AC+X-DC+BATfor2supply

X800-90-0003RAIL,COMBI,ACfor2supply
X800-91-0003RAIL,COMBI,AC+X-DCfor2supply
X800-92-0003RAIL,COMBI,ACfor2supply
X800-93-0003RAIL,COMBI,AC+BATfor2supply
X800-94-0003RAIL,COMBI,X-DC+BATfor2supply
X800-95-0003RAIL,COMBI,AC+X-DC+BATfor2supply

T A I T

Radio Communications
Christchurch
New Zealand

DRAWING:

power rails cso.vsd

TITLE:

X800 - 9x - 0000

POWER RAIL OPTIONS for T800 RACKS

Drawn DateChecked

AMM 8/9/99ABB

AMM 26/10/99ABB

Version

12Original

Diode position changed

AC POWER SUPPLY EXTERNAL DC AND BATTERY

x = 5

EXTERNAL DC AND BATTERY

x = 4

AC POWER SUPPLY AND BATTERY

x = 3

EARTH

STUD

BATTERY
BACK-UP

FUSE

TB1

OPTIONAL

POSITION

OUTPUT

ONLY 13.8V

MAX

2 AMPS

DIODE

PACK

EARTH

STUD

DC INPUT FUS E

TB1

OUTPUT

ONLY 13.8V

MAX

2 AMPS

EARTH

STUD

DC INPUT FUS E

TB1

OUTPUT

ONLY 13.8V

MAX

2 AMPS

DIODE

PACK

EARTH

STUD

BATTERY
BACK-UP

TB1

OUTPUT

ONLY 13.8V

MAX

2 AMPS

DC INPUT FUSE

OPTIONAL

POSITION

DIODE

PACK

EARTH

STUD

BATTERY
BACK-UP

TB1

OUTPUT

ONLY 13.8V

MAX

2 AMPS

DC INPUT FUSE

OPTIONAL

POSITION

DIODE

PACK

AC POWER SUPPLY ONLY

x = 0

EARTH

STUD

FUSE

TB1

OUTPUT

ONLY 13.8V

MAX

2 AMPS

EXTERNAL DC SUPPLY ONLY

x = 1

AC POWER SUPPLY AND EXTERNAL DC

x = 2