User Guide
Bedienungsanleitung
Guide de l’utilisateur
Guía del Usuario
© Copyright Tait Electronics Ltd August 2004. All rights reserved.
1
Declaration of Conformity (Europe)
Dansk Undertegnede Tait Electronics Ltd erklærer herved, at
følgende udstyr T2000 overholder de væsentlige krav
og øvrige relevante krav i direktiv 1999/5/EF.
Se endvidere: http://eudocs.taitworld.com/
Deutsch Hiermit erklärt Tait Electronics Ltd die Übereinstimmung
des Gerätes T2000 mit den grundlegenden
Anforderungen und den anderen relevanten
Festlegungen der Richtlinie 1999/5 EG.
Siehe auch: http://eudocs.taitworld.com/
Ελληνικός Με την παρουσα Tait Electronics Ltd δηλωνει οτι
T2000 συµµορφωνεται προσ τισ ουσιωδεισ
απαιτησεισ και τισ λοιπεσ σχετικεσ διαταξεισ τησ
οδηγιασ 1999/5/ΕΚ.
βλέπε και: http://eudocs.taitworld.com/
English Tait Electronics Ltd declares that this T2000 complies
with the essential requirements and other relevant
provisions of Directive 1999/5/EC.
See also: http://eudocs.taitworld.com/
Español Por medio de la presente Tait Electronics Ltd declara
que el T2000 cumple con los requisitos esenciales y
cualesquiera otras disposiciones aplicables o exigibles
de la Directiva 1999/5/CE.
Vea también: http://eudocs.taitworld.com/
2
Declaration of Conformity (Europe)
Français Par la présente, Tait Electronics Ltd déclare que
l'appareil T2000 est conforme aux exigences
essentielles et aux autres dispositions pertinentes de la
directive 1999/5/CE.
Voir aussi: http://eudocs.taitworld.com/
Italiano Con la presente Tait Electronics Ltd dichiara che questo
T2000 è conforme ai requisiti essenziali ed alle altre
disposizioni pertinenti stabilite dalla direttiva 1999/5/CE.
Vedi anche: http://eudocs.taitworld.com/
Nederlands Hierbij verklaart Tait Electronics Ltd dat het toestel
T2000 in overeenstemming is met de essentiële eisen
en de andere relevante bepalingen van richtlijn
1999/5/ EG.
Zie ook: http://eudocs.taitworld.com/
Português Tait Electronics Ltd declara que este T2000 está
conforme com os requisitos essenciais e outras
provisões da Directiva 1999/5/CE.
Veja também: http://eudocs.taitworld.com/
Suomi Tait Electronics Ltd vakuuttaa täten että T2000
tyyppinen laite on direktiivin 1999/5/EY oleellisten
vaatimusten ja sitä koskevien direktiivin muiden ehtojen
mukainen.
Katso: http://eudocs.taitworld.com/
Svensk Härmed intygar Tait Electronics Ltd att denna T2000
står I överensstämmelse med de väsentliga
egenskapskrav och övriga relevanta bestämmelser som
framgår av direktiv 1999/5/EG.
Se även: http://eudocs.taitworld.com/
3
4
User Guide ................................................................................. 7
Safety Warnings .................................................................. 8
Getting Started .................................................................... 11
Making a Call ....................................................................... 12
Receiving a Call ................................................................... 13
Call Queuing ........................................................................ 14
Status Calls .......................................................................... 15
Alphanumeric Entry Mode .................................................. 16
Removing the Radio from the Vehicle ................................ 17
Installation ............................................................................ 18
Bedienungsanleitung .............................................................. 29
Sicherheitsvorkehrungen .................................................... 30
Inbetriebnahme ................................................................... 33
Rufaussendung ................................................................... 34
Rufempfang ......................................................................... 35
Anrufspeicherung ................................................................ 36
Statusrufe ............................................................................. 37
Alphanumerischer Eingabemodus ..................................... 38
Geräteentnahme aus dem Fahrzeug ................................. 39
Montageanleitung ................................................................ 40
Guide de l’utilisateur ................................................................ 51
Précautions de sécurité ...................................................... 52
Mise en route ....................................................................... 55
Lancement d’un appel ........................................................ 56
Réception d’un appel .......................................................... 57
Mémorisation des appels .................................................... 58
Appels d’état ........................................................................ 59
Mode d’entrée alphanumérique ......................................... 60
Retirer la radio du véhicule ................................................. 61
Installation de votre radio .................................................... 62
5
Guía del Usuario ....................................................................... 73
Medidas de seguridad ........................................................ 74
Para comenzar .................................................................... 77
Cómo hacer una llamada ................................................... 78
Cómo recibir una llamada .................................................. 79
Llamadas en espera ........................................................... 80
Llamadas de estado ........................................................... 81
Modo de entrada alfanumérica .......................................... 82
Cómo sacar la radio del vehículo ....................................... 83
Instalación de la Radio ....................................................... 84
..................................................................................................... 95
.....................
.......................................................... 97
.....................
.....................
.......................................................... 98
.......................................................... 99
.......................................................... 100
.......
.......................................................... 101
.............................................................................................. 88
.....................
.......................................................... 103
............
.......................................................... 103
.........
.......................................................... 104
6
T2040
II
User Guide
English
7
Safety Warnings
• Switch the radio off at petrol filling stations.
• Switch the radio off in the vicinity of explosive devices,
such as in a quarry that uses blasting techniques.
• Use of a handheld microphone or a radio while driving
could contravene the legislation that applies in your
country or state. Please check the vehicle regulations
in your own country.
EN60950 Compliance
This radio complies with the European Union standard
EN60950, when operated up to the rated 33% duty cycle of
two minutes transmit and four minutes receive, and at an
ambient temperature of 30°C or lower. Operation outside
these limits may cause the external temperature of the radio
WARNINGWARNING
to rise higher than specified by EN60950.
To ensure compliance with EN60950, the radio should be
mounted in such a position that will prevent the user from
coming into contact with the radio’s heatsink.
FCC RF Exposure Limits
This product generates radio frequency energy during
transmissions. This device must be restricted to workrelated use in an occupational/controlled exposure
environment. The radio operator must have control of the
exposure conditions and duration of all persons exposed to
the antenna of this transmitter to satisfy FCC RF exposure
compliance.This device is not approved for general
population use.
The following conditions apply to the use of this radio:
• It must only be used with authorized accessories and
antennas.
• The operator must ensure that the minimum safe distance
of 0.9m (35 inches) between persons and the antenna is
not exceeded during transmissions.
• Do not exceed a duty cycle ratio of 50% transmit mode to
stand-by or receive modes. The radio is in transmit mode
when the PTT key on the microphone is pressed and the
TX indicator shows in the display window.
8
English
Compliance Information
Health, safety and
electromagnetic
compatibility in
Europe
In the European Community, radio and
telecommunications equipment is regulated by
Directive 1999/5/EC, also known as the Radio and
Telecommunications Terminal Equipment (R&TTE)
directive. The requirements of this directive include
protection of health and safety of users, as well as
electromagnetic compatibility.
Intended purpose of product
This product is an FM radio transceiver. Its intended
purpose is for radio communication in Private Mobile
Radio (PMR) services or Public Access Mobile Radio
(PAMR) services.
Note: This product can be programmed for
frequencies or emissions that may make its use
illegal. A licence must be obtained before this product
Electromagnetic
compatibility in
European
vehicles
is used. All licence requirements must be observed.
Limitations may apply to transmitter power, operating
frequency, channel spacing, and emission.
Declaration of conformity
Brief Declarations of Conformity appear on page 2.
The formal Declaration of Conformity can be
downloaded from http://eudocs.taitworld.com/.
A signed and dated paper copy of the Declaration of
Conformity can be obtained from Tait Europe Ltd.
In the European Community, radio equipment fitted
to automotive vehicles is regulated by Directive 72/
245/EEC, as amended by 95/54/EC. The
requirements of this directive cover the
electromagnetic compatibility of electrical or
electronic equipment fitted to automotive vehicles.
Note: To meet the requirements of Directive
72/245/EEC (as amended by 95/54/EC), installation
English
9
Compliance Information
of this product in a vehicle must be performed
according to the instructions provided, and any
guidelines of the vehicle manufacturer.
Radio frequency
emissions limits
in the USA
Additional
information
Part 15 of the FCC Rules imposes RF emission limits
on electronic equipment to prevent interference to
reception of broadcast services.
This device complies with Part 15 of the FCC Rules.
Operation is subject to the condition that this device
does not cause harmful interference.
Note: Changes or modifications to this device that are
not expressly approved by Tait Electronics Ltd may
make its use illegal.
For product details and contact details of Tait offices,
visit http://www.taitworld.com/.
For technical assistance, visit
http://support.taitworld.com/.
10
English
Getting Started
Introduction Your T2040
allows it to be configured to suit the needs of your
particular fleet.
This User’s guide provides a brief description of the
basic features of your radio. For information about the
advanced features, a comprehensive operators’ manual
is available from your Tait dealer.
Switching on Turn the On/Off-Volume control to about one-third of its
maximum turn. You may need to finally adjust the
volume when you receive your first call.
Checking
System
Availability
Check to see that the SVC (service) indicator appears in
the display within a few seconds, showing that your
radio has logged on to the network.
There are three possible indications:
II is controlled by a microprocessor which
SVC Indicator To change to the channel:
Continuous
Blinking
Absent
Transmit Timer The radio is fitted with a preprogrammed timer to limit
the maximum length of transmissions. When this time
limit is reached, a three tone warning is sounded and
transmission stops. You must release the PTT key
before proceeding.
Your radio has access to a network
and is ready to make or accept calls.
Your radio does not currently have
access to a network. It is attempting
to find a site it is authorised to use, or
it may be out of range of a network
signal.
Your radio is in Conventional mode.
English
11
Making a Call
Sending a Call There are four ways to make a call using your T2040
1 Enter the full number of the required party using the
numeric keypad and then press the Hash ()
key to send the call.
2 Enter a two-digit short dial preset number using the
numeric keypad and then press the Hash ()
key to send the call.
3 Use the Despatcher ( ) and Function ( )
Fn
keys which may each be preprogrammed to send a
call directly, when you apply a long press. The
Despatcher ( ) key is usually preprogrammed
to call your base despatcher.
4 Use an alphanumeric label to select a call identity
(see “Alphanumeric Entry mode”).
II:
Using the
Microphone
and PTT key
You may hear call setup tones followed by a ringing tone
similar to that of a telephone, and the WAIT indicator
may be displayed. When the called party answers, the
WAIT indicator is replaced by the GO indicator and you
may proceed with your conversation.
The PTT key on the side of the microphone switches the
radio between transmit and receive modes.
Each time the radio transmits, the TX indicator appears
in the display.
To speak, press the PTT key. Hold the microphone
about 5cm from your mouth and pause briefly to ensure
your first word is not cut off, then speak clearly. Release
it to listen to the reply.
12
English
Receiving a Call
When you receive a call your radio will alert you with a
ringing tone like a telephone and the identity of the caller
will be displayed as explained below.
Responding to
Calls
Caller
Identification
Display Example: Explanation:
Label
You may accept a call by lifting the microphone from its
clip, pressing the PTT key and identifying yourself (for
example “Mobile-9 Receiving”).
If you do not want to accept the call, press the Clear
( ) key and the call will be cancelled.
If the call is a group call, you will hear a single ring and
then the caller will broadcast a message to all members
of your group. It is not normally necessary to reply.
The source of an incoming call or the caller’s identity is
shown in the display as follows:
VEHICLE7 The calling party is one of your preset
numbers with a label preprogrammed
Preset
Number
Call
Number
System
Message
System
Message
System
Message
into your radio.
8 The calling party is one of your network
stored preset numbers without a label
preprogrammed into your radio.
23 The calling party is in the same fleet as
your radio but is not preprogrammed.
OFLT The calling party is not in the same fleet
as your radio and is not preprogrammed.
PHONE A call from the PSTN (Public Switched
Telephone Network).
PABX A call from the PABX (Private Automatic
Branch Exchange).
English
13
Call Queuing
Setting
Queuing On
Handling Saved
Calls
If you need to leave your T2040
have it save incoming calls as call-back messages for
you to return later.
To set call queuing on and have all calls except “group,
PABX and PSTN” calls queued:
• Press the Despatcher ( ) key until the indicator
beside it illuminates.
When you return to your radio it displays the number of
calls received and the identity of the first caller. You
may:
1 Return the displayed call by pressing the PTT key.
2 Discard the call by pressing the Clear () key.
3 Scroll to another message using the Up and Down
II unattended, you may
( / ) keys and handle it as above.
4 Make a new outgoing call as normal.
Cancelling Call
Queuing
Do Not Disturb You may set your T2040
You may restore the radio to normal operation by
pressing the Despatcher ( ) key again until the
indicator beside it extinguishes.
The radio will now alert you normally when a call is
received. If you still have calls saved in the queue, they
are preserved and you may recover them at any time by
turning call queuing back on.
whilst allowing you to make calls out normally. The
radio will display QUIET and callers will be given the
“unavailable” response.
II to reject all incoming calls
• To set ‘Do Not Disturb’, dial *49#.
• To cancel, dial #49# or press the Clear () key,
and the QUIET message is removed from the display.
14
English
Status Calls
Status calls permit the rapid exchange of simple
messages without voice conversation. Your radio can
have messages such as “En route”, “At lunch” and so on
preprogrammed.
Sending a
Status
Message
Receiving a
Status
Message
To select and send a status message:
1 Press the Status ( ) key and use the ( /
STAT
) scroll keys to select an appropriate message.
2 To send the message to your despatcher, press the
Hash () key.
3 To send the message to any other party, press the
Star ( ) key, and then:
• Dial the identity number using the keypad, or
• Select an alphanumeric label for the call.
4 Press the Hash ( ) key to make the call.
When you receive a status call, your T2040
II
automatically enters the Call Queuing mode.
The status message value shows on the left of the
display and the caller’s identity on the right.
If the status message corresponds to a label which is
preprogrammed into your radio, the indicator beside the
Alphanumeric ( ) key flashes. To view the label:
• Press the Alphanumeric () key.
English
15
Alphanumeric Entry Mode
To perform repetitive operations which require several
Selecting a
Sequence
keystrokes, your T2040
II may be preprogrammed with
alphanumeric labels. These labels, when recalled, can
perform a series of operations such as sending a call.
To use preset sequences, select them by their label as
follows:
1 Press the Alphanumeric ( ) key to enter the
Alphanumeric Entry mode.
2 Locate the desired label by using the up/down keys
( / ) to scroll through the list until the label
is displayed, or enter the label for the required party,
using the keypad.
3 Press the Hash ( ) or the PTT key to initiate the
labelled action as it is preprogrammed.
Example You want to call your base despatcher who has been
assigned the label, BASE. The keystroke sequence and
display might appear as follows:
Press key Display reads Explanation
Most recent selection displayed
ABC
ABC
2
2
ABC
2
PQRS
7
Label not yet identified
Label not yet identified
New label identified
BASE is called and the
or
PTT key
BASE number is displayed
16
English
Removing the Radio from the Vehicle
Removing the
radio from its
cradle
For security, you may remove the radio from the
vehicle.The radio can be removed from its cradle using
the special key as follows:
1 Switch the radio off.
2 Insert the key in the
slot beside the volume
control as shown.
3 Holding the radio’s
front panel by its edges, pull the radio towards you
until it is clear of the cradle.
4 Disconnect the antenna and other cables from the
rear of the radio.
5 Remove the radio.
English
17
Installation
Components of
II
the T2000
Radio Kit
The T2000
• T2000
• Microphone
• Complete Cradle
• 4 Ohm Speaker (not for internal speaker models)
Installation Kit
• Two-way Hermaphroditic
Connector (1)
• Socket Receptacle (2)
• 10A 12V Blade Fuse (2)
• In-line Crimp Fuse Holder
(2)
II Radio kit includes the following parts:
II Radio Unit
• BNC Antenna Crimp Plug
• Cradle Keys (2)
• Power Cable (5m)
• Self Tapping Screw (4)
• Shakeproof Washer
(4)
• Microphone Clip Kit (1)
• Control Head Mounting
Bracket (T2020
T2040
II only)
II and
Recommended
Installation
Tools
18
English
• Portable Drill
• Centre Punch
• Drill Bits: 4mm for self-tapping screws, 6mm for nuts
and bolts
•“Pozidriv” Screwdrivers
• BNC Crimp Tool (e.g. Transradio England Duo Crimp
894)
• In-line Power Meter capable of measuring forward and
reflected power at the operating frequency of the radio
• Hammer
Figure 1: Radio Kit Components
Installation
Installation
Planning
Occupant’s
Safety
To ensure trouble-free, efficient installation, inspect the
vehicle and determine how and where the antenna,
radio and accessories are to be mounted.
It is possible to remote-mount the T2020
models as these have alphanumeric keypads, with the
control head separate from the radio chassis.
This enables the radio to be mounted in a discrete
location, e.g. the rear luggage space, with the control
head mounted in a convenient position for the vehicle’s
occupants. See the M2000 service manual, available
from your Tait dealer, for details of this modification.
Check that the chosen locations for the radio and
accessories do not endanger the vehicle occupants.
Overhead mounting is not recommended, especially
II and T2040II
without an additional safety strap. Check that the radio
can be conveniently operated when seat belts are worn.
Caution: To prevent interference with vehicle electronic
systems (such as ignition and anti-skid devices), the
radio, its antenna and wiring should be mounted away
from these units and their associated cables.
Allow sufficient airflow around the radio to permit
adequate cooling. Once you have found a suitable
mounting position for the radio, hold it (fitted in the
cradle) in the proposed mounting position and check
there is clearance behind it for the heatsink, cables, etc.
Check that the position provides a large enough flat
surface that the cradle will not be distorted.
Important: To ensure compliance with EN60950, the
radio should be mounted in such a position that will
prevent the user from coming into contact with the
radio’s heatsink.
English
19
Installation
To Disassemble
the Cradle
1 Remove the radio from its cradle by sliding the plastic
key supplied with the radio fully into the slot on the left
front of the radio unit. The radio will now slide out
forwards from the cradle, as shown below:
Cradle
Radio Unit
Plastic Key
Figure 2: Cradle and Key
2 Disassemble the
cradle by placing it
on a firm surface
and applying
pressure down on
one of the middle
ribs of the plastic
side moulding with
a screwdriver. This
will release the
ribs along this
edge from the
Figure 3: Cradle Disassembly
slots in the metal cover with which they mate. A
similar approach will release the other edge of the
metal cover which can now be lifted clear (Figure 3).
Mounting Hold the drilled half of the metal cradle cover in the
position chosen for the radio and use the four cradle
cover mounting holes as a template to mark the
locations for drilling (see figure 4). Ensure that drilling at
the selected points will not damage existing wiring.
Indent the drilling positions with a centre punch and drill
4mm holes for self-tapping screws, or 6mm holes for
20
English
Installation
nuts and bolts. Reduce the hole size if using self-tapping
screws in metal that is less than 1mm thick.
Drill any additional holes required for cables and fit them
with suitable grommets or bushings.
Secure the metal cradle cover to the mounting points
with the M5 self-tapping screws supplied, or with M5
nuts and bolts. Ensure that tightening the screws or
bolts does not distort the cradle.
Figure 4: Mounting
English
21
To Reassemble
the Cradle
Installation
Figure 5: Cradle Reassembly
Antenna
Installation
To comply with FCC RF exposure limits,
this product must be installed using an
antenna with a gain specified below:
WARNING
Product Antenna Gain
T20xx-K27
T20xx-815
T20xx-3xx
T20xx-543
T20xx-643
4.5 dBi
2.15 dBi or 5.15 dBi
To install the antenna:
1 Terminate one end of the coaxial cable at the
antenna. Good quality 50 ohm coaxial cables such as
RG58 or UR76 are suitable. Run the free end of the
coaxial cable to the radio’s mounting position and cut
it to length allowing 200mm to 300mm excess.
22
English
Installation
a
a
a
a
aaaaaaaa
b
b
b
b
bbbbbbbb
2 Terminate the free end of the cable with the BNC
crimp plug supplied, as shown in Figure 6:
• Fit the crimp sleeve over the cable sheath.
• Trim the outer sheath from the cable to 15mm (see
Figure 6 below).
• Trim the braid to 8.5mm.
• Trim the dielectric to 11mm. (Take extreme care not to
‘nick’ the centre conductor with the trimming device.)
• Fit the male pin onto the centre conductor with the
shoulder pressed against the end of the dielectric.
• Crimp the male pin onto the centre conductor.
• Press the assembly firmly into the rear of the plug.
(Ensure that no braid gets trapped between the
dielectric and the inside of the plug.)
• Slide the crimp sleeve over the braid and press
against the shoulder of the plug.
• Crimp the crimp sleeve onto the braid and plug body.
Crimp Sleeve
aaaaaa
bbbbbb
aaaaaa
bbbbbb
Male Pin
Plug
Figure 6: Antenna Connector Assembly
English
23
Installation
Wiring External Speaker
Some T2000
However it is possible to fit an external speaker if
required, by terminating a twin wire in the power
connector. To disable the internal speaker, cut the link
on the power connector as shown in Figure 7.
T2000
external speaker fitted. The power connector comes
pre-wired with the speaker cable.
Power
Supply
II models with no internal speaker must have an
Ignition
External
+13.8V
{
Ground
II models are fitted with internal speakers.
Internal Speaker Link
(cut to disable)
Ground
Live
External Speaker
}
Figure 7: Power Connector Wiring
Mount the external speaker in a convenient location
close to the operator. Run the free end of the speaker
wire to the speaker, and connect it to the speaker plug.
Power Cable
1 Disconnect the vehicle’s battery unless specifically
prohibited from doing so by the customer, vehicle
manufacturer, agent or supplier. In this event,
exercise extreme caution throughout the installation
and fit the fuses only when the installation is
complete.
Caution: Always disconnect the radio’s power lead
before connecting a second battery or using power
from another vehicle (e.g. when “jump-starting” the
vehicle).
2 Determine where the battery leads will be routed.
24
English
Installation
3 Cut the negative and the positive wires where the in-
line crimp fuse holders will be placed (as close to the
battery as practicable).
4 Insert each end of the negative wire into one of the in-
line crimp fuse holders and crimp them to force the
metal contacts onto the wires. Terminate the wire at
the battery earth.
5 Repeat Step 4 for the positive wire and terminate it at
the positive terminal of the battery.
Caution: Prevent the power wires chafing on any
metal parts.
Note: T2000II radios are designed to operate from a
nominal 12V negative earth supply, and require
currents of up to 8A. (The radios will tolerate a supply
voltage range of 10.8V to 16.0V). In vehicles with a
24V electrical system (e.g. many trucks), it is
essential to provide a suitably rated 24/12V converter
to isolate the radio from the battery and protect it
against excessive voltages.
6 If the economiser is to be controlled by the ignition
line, terminate a wire in the power connector and
connect the ‘ignition’ wire to a +12V supply which is
live only when the vehicle’s ignition is switched ‘On’.
English
25
Installation
External Wire
(Horn/Hush/
Emergency)
Remote Control
Head Option
The T2000
horn, radio or a hidden switch:
1 Terminate a suitable length of wiring in the “external”
port of the power connector.
2 Run the free end of the external wire from the power
connector to the appropriate vehicle wiring.
The option’s interface is usually configured to switch or
be switched in the ground state. Confirm the exact
operation in the documentation supplied with the
interface unit.
The control head of some T2000
supplied ready for mounting remotely from the radio
chassis. In this case the control head should be located
away from direct sunlight, and the cable connecting it to
II can be configured to operate the vehicle’s
II models may be
the radio should be routed away from the antenna with
care taken to ensure that the cable will not be subject to
damage.
If it is necessary to run the cable through a bulkhead or
similar obstruction, you may unplug the cable from the
control head as follows (see also figure 8):
1 Unscrew the rear of the control panel and lift off the
rear cover, taking care not to lose the two nuts located
on each end.
2 Disconnect the red connector from the printed circuit
board socket to free the cable.
3 Route the cable as required, fitting grommets where
necessary to prevent chafing of the cable insulation.
4 Fit the red connector to the printed circuit board
socket – the connector is shaped so that it can be
fitted in the correct orientation only.
26
English
Installation
5 Refit the cable to the cable clamp on the rear cover
and slip the two nuts into the receptacles at each end
of the rear cover.
6 Refit the rear cover and replace the cover screws,
tightening them carefully. Do not overtighten the
screws.
The control head can now be installed as follows:
7 Mount the bracket for the control panel on a flat
surface using the self-tapping screws supplied.
8 Place the control head in the bracket, position it for a
Figure 8: Remote Control Head Option
good viewing angle, and fit the 2 screws to secure it in
place.
English
27
Installation
Microphone
Clip
Installation
Checks
The microphone clip must be earthed (to the negative
supply line) if hookswitch control of monitoring, scanning
or call termination is to operate. Refer to the radio’s
operating instructions to confirm requirements.
Ensure that the microphone clip is mounted in a position
where the microphone PTT key cannot be inadvertently
activated or jammed on.
1 Plug the microphone into the socket on the lower left-
hand corner of the radio’s front panel. Push the cable
grommet into the rectangular aperture in the panel.
2 Insert the fuses into the power lead.
3 Switch on the radio and confirm that it is operational.
4 Connect an in-line power meter between the radio
and the antenna and measure the forward and
reflected power levels. Less than 1W should be
reflected for 25W forward power. If this is not
achieved, check the installation – including antenna
length.
5 Make a call to another party on the radio (as
described in the operating instructions).
28
English
Loading...