System Sensor RA100Z, RA100ZA Installation And Maintenance Instructions Manual

INSTALLATION AND MAINTENANCE INSTRUCTIONS

CAUTION

I56-0508-008

RA100Z and RA100ZA (Canadian)
Remote Annunciator

SPECIFICATIONS

Voltage Range
Conventional System: 3.1 to 32 VDC — (Installation of jumper required) Note 1
Intelligent System: 18 to 32 VDC — (Do not install jumper)
Maximum Alarm Current: 10 mA maximum.
Temperature Range: –10° to 60°C (14° to 140°F)
Listing: UL, FM, CE

Install jumper when using an RA100Z or RA100ZA with any conventional duct detector (such as the System Sensor model D2 or D4120).

NOTE: RA100Z and RA100ZA replaces RA400Z and RA400ZA .

GENERAL INFORMATION

The National Fire Protection Association has published codes, standards, and
recommended practices for the installation and use of the above appliance. It
is recommended that the installer be familiar with these requirements, with
local codes, and any special requirements of the local authority having juris­diction.

The models RA100Z & RA100ZA remote annunciators are polarized devices
designed for both conventional and intelligent applications. They have been
designed using an active current regulator so that the maximum current re­quired from the system is 10mA when the input voltage is within the specified
voltage range.

INSTALLATION

The remote annunciator is intended to be mounted to a single gang electrical
outlet box. The wiring must be in compliance with all codes. The device must
be operated within its published specifications.

Wire the remote annunciator according to the instructions supplied with the
device being monitored. Polarity of the incoming wires must be observed and
connected to the proper terminals “+” and “–”. (See Figure 2.)

The provided jumper must be installed for use with System Sensor Conventional
systems. To install jumper: slide jumper over both pins. (see Figure 3/Note 1)

FIGURE 1:

3825 Ohio Avenue, St. Charles, Illinois 60174

1-800-SENSOR2, FAX: [phone]

www.systemsensor.com

1 I56-0508-008
06-10

H0355-01

INSTALL JUMPER —

WARNING

FIGURE 2:

FIGURE 3:

H0354-01

THE LIMITATIONS OF REMOTE ANNUNCIATORS

THE REMOTE ANNUNCIATOR WILL NOT WORK IF THE DEVICE IT IS CONNECTED
TO IS NOT POWERED. The remote annunciator gets its power from the device to which
it is connected. If for any reason, the device being monitored loses power, the remote
annunciator will not provide the intended visible signal.
THE REMOTE ANNUNCIATOR MAY NOT BE SEEN. The model RA100Z is suitable for
direct viewing and is in compliance with existing Underwriters Laboratories’ standards.
The device must be sited in a location where it can be seen by the intended parties. The

REQUIRED FOR CONVENTIONAL SYSTEM

H0356-01

device must not be installed in direct sunlight, or areas of high light intensity where the
visible signal might be disregarded or not seen.
THIS DEVICE IS DESIGNED TO WORK SPECIFICALLY WITH SYSTEM SENSOR
PRODUCTS. Interconnection with devices other than System Sensor’s may result in un
satisfactory operation. Consult device manufacturer for compatibility.
THE REMOTE ANNUNCIATOR IS NOT INTENDED TO BE A VISIBLE WARNING SIGNAL.

-

System Sensor warrants its enclosed smoke detector base to be free from defects in ma­terials and workmanship under normal use and service for a period of three years from
date of manufacture. System Sensor makes no other express warranty for this smoke
detector base. No agent, representative, dealer, or employee of the Company has the au
thority to increase or alter the obligations or limitations of this Warranty. The Company’s
obligation of this Warranty shall be limited to the repair or replacement of any part of
the smoke detector base which is found to be defective in materials or workmanship
under normal use and service during the three year period commencing with the date of
manufacture. After phoning System Sensor’s toll free number 800-SENSOR2 (736-7672)
for a Return Authorization number, send defective units postage prepaid to: Honeywell,

2 I56-0508-008
©2016 System Sensor. 06-10

THREE-YEAR LIMITED WARRANTY

12220 Rojas Drive, Suite 700, El Paso TX 79936, USA. Please include a note describing the
malfunction and suspected cause of failure. The Company shall not be obligated to repair
or replace units which are found to be defective because of damage, unreasonable use,
modifications, or alterations occurring after the date of manufacture. In no case shall the

­Company be liable for any consequential or incidental damages for breach of this or any
other Warranty, expressed or implied whatsoever, even if the loss or damage is caused by
the Company’s negligence or fault. Some states do not allow the exclusion or limitation of
incidental or consequential damages, so the above limitation or exclusion may not apply
to you. This Warranty gives you specific legal rights, and you may also have other rights
which vary from state to state.