Synology DS218j User Manual
Synology DiskStation DS218j
Hardware Installation Guide
Table of Contents
Chapter 1: Before You Start
Package Contents 3
Synology DiskStation at a Glance 4
Safety Instructions 5
Chapter 2: Hardware Setup
Tools and Parts for Drive Installation 6
Install Drives 6
Start Up Your DiskStation 8
Chapter 3: Install DSM on DiskStation
Install DSM with Web Assistant 9
Learn More 9
Appendix A: Specications
Appendix B: LED Indicator Table
Synology_HIG_DS218j_20170725
2
Chapter
Before You Start
Thank you for purchasing this Synology product! Before setting up your new DiskStation, please check the
package contents to verify that you have received the items below. Also, make sure to read the safety instructions
carefully to avoid harming yourself or damaging your DiskStation.
Note:
All images below are for illustrative purposes only, and may differ from the actual product.
Package Contents
Main unit x 1 AC power cord x 1
AC power adapter x 1
1
HDD bracket x 1 Screws for HDD bracket x 3 Screws for hard drives x 10
RJ-45 LAN cable x 1
Screws for xing the
Synology case x 3
3
Synology DiskStation at a Glance
No. Article Name Location Description
1
Status Indicator
Displays the status of the system. For more information, see "Appendix B: LED
Indicator Table".
2
3
4
5
6
7
8
9
10
LAN Indicator
Front Panel
Disk Indicator
Power Button
and Indicator
Fan
LAN Port Connect a network cable here.
USB 3.0 Port Connect external hard drives or other USB devices to the DiskStation here.
Back Panel
RESET Button
Kensington
Security Slot
Power Port Connect the AC power adapter here.
Displays the status of the network connection. For more information, see
"Appendix B: LED Indicator Table".
Displays the status of the installed drives. For more information, see "Appendix B:
LED Indicator Table".
1. Press to power on the DiskStation.
2. To power off the DiskStation, press and hold until you hear a beep sound and
the Power LED starts blinking.
Disposes of excess heat and cools the system. If the fan malfunctions, the
DiskStation will emit a beeping sound.
1. Press and hold until you hear a beep sound to restore the default IP address,
DNS server, and password for the
2. Press and hold until you hear a beep sound, then press and hold again until
you hear three beep sounds to return the DiskStation to “Not Installed” status
so that DiskStation Manager (DSM) can be reinstalled.
Attach a Kensington security lock here.
admin
account.
4 Chapter 1: Before You Start
Safety Instructions
Keep away from direct sunlight and away from chemicals. Make sure the environment does not
experience abrupt changes in temperature or humidity.
Place the product right side up at all times.
Do not place near any liquids.
Before cleaning, unplug the power cord. Wipe with damp paper towels. Do not use chemical or
aerosol cleaners.
To prevent the unit from falling over, do not place on carts or any unstable surfaces.
The power cord must plug in to the correct supply voltage. Make sure that the supplied AC voltage is
correct and stable.
To remove all electrical current from the device, ensure that all power cords are disconnected from
the power source.
Risk of explosion if battery is replaced with an incorrect type. Dispose of used batteries appropriately.
5 Chapter 1: Before You Start
Chapter
Hardware Setup
Tools and Parts for Drive Installation
• A screwdriver
• At least one 3.5” or 2.5” SATA drive (please visit www.synology.com for compatible drive models)
Warning: If you install a drive that contains data, the system will format the drive and erase all existing data. Please
back up any important data before installation.
Install Drives
1
Push the upper case in the direction as shown below. Lift the upper case and set it aside.
2
2
Install drives:
For 3.5” drives with 3 screw holes on each side (indicated below):
•
a
Slide the drive into the hard drive bay, and push it all the way until it’s rmly connected to the SATA
connector.
b
Secure the drive with the screws provided.
For 3.5” drives with 2 screw holes on each side (indicated below):
•
6
Loading...