
Instructions For Models
Instructions For Models:
SPP-3510 & SPP-3510-STN
What You Need To Have
Tools
Adjustable Wrench 
Pliers 
Pipe Wrench 
Phillips Head Screwdriver
Teflon Tape
Maintenance
Your new kitchen faucet is designed for years of trouble-free 
performance. 
Keep it looking new by cleaning it periodically with a soft cloth. 
Avoid abrasive cleaners, steel wool and harsh chemicals as 
these will dull the finish and void your warranty.
HELP LINE
Need Help? 
Symmons customer service: 
(800) 796-6667, (781) 848-2250 
customerservice@symmons.com 
Mon - Fri 7:30 am - 7:00 pm EST 
Website:www.symmons.com
Safety Tips
If you use soldering for the installation of your faucet, the seat 
cartridges and washers will have to be removed before using
flame. Otherwise, warranty will be void on these parts.
Protect your eyes with safety glasses when cutting or soldering
water supply line.
Cover your drain to avoid loosing parts.
Important Points
Prior to beginning installation, turn off the cold and hot water lines 
and open the old faucet to release built-up pressure. 
When installing your new faucet, turn the connector nuts hand 
tight, then use one wrench to anchor the fitting and a second 
wrench to tighten the nut one additional turn. Connections that 
are too tight will reduce the integrity of the system. 
Wrap all threaded connections with Teflon tape available at your 
local hardware or plumbing supply store. Always wrap in a clockÂwise direction.
Page 1
ZV-1083
Rev B

Things You May Need
All installations can vary depending on how your previous faucet
was installed. Necessary supplies to install your faucet are not all 
included: however they are available wherever plumbing supplies 
are sold. When choosing your installation supplies, make sure 
they are IAPMO and / or CSA approved products.
2
Attach Spout to Valve 
Feed hose assembly through spout and hub. Attach 
sprayer to end of hose to keep hose in place. Rotate 
spout assembly to ensure smooth operation.
Shut off water supply. Remove old faucet. Clean sink
1
surface in preparation for new faucet.
Mount Faucet to Deck
3
Place flange on bottom of hub. Insert faucet through 
mounting holes in sink. Your faucet is designed for a hole 
diameter of 1 3/8" +/- 1/4"(35mm+/- 6mm) and a deck 
thickness of up to 2 1/2" (64mm).
Page 2

Install rubber washer, metal washer and nut onto the
4
mounting shank.
Connect to water supplies (HOOK-UPS NOT PROVIDED)
6
Note: Refer to local plumbing codes for permissible types 
of water supply connectors.
(A)
(B)
Hose Installation
5
Align block (1) onto hose. Install quick connect onto spray 
hose. Push quick connect firmly onto outlet hose tab. 
Install weights onto spray hose. Locate the weights 24"
from the underside of the sink deck.
24"
Faucet Operation and Inspection
7
Turn on hot and cold water supplies. Pull the hose 
assembly out of the spout and remove aerator(1) with
wrench(2). Be sure to hold the end of the hose down into 
the sink and turn faucet handle to the mixed position. 
Flush water lines for one minute. Check for leaks. 
Re-tighten if necessary, but do not overtighten. Reinstall 
the spray head tight.
1
2
Page 3

RK-004
RK-007
RO-006 (2.2 gpm, 8.3 L/min) 
RO-007 (1.5 gpm, 5.7 L/min) 
RO-008 (1.0 gpm, 3.8 L/min)
RK-003
RK-001
RK-002
RK-005
RK-006
Page 4