
Wall Mounted Grab Bar SGB
Installation Instructions
Model Numbers
SGB-24 ........ 24 inch ADA Grab Bar
SGB-36 ........ 36 inch ADA Grab Bar
SGB-42 ........ 42 inch ADA Grab Bar
Tools and Materials
5/32" drill bit
1/4" carbide
tip drill bit for
wall tiles
Compliance
2010 ADA Standards for Accessible Design
Grab bar assembly complies with the
applicable requirements.
Visual Guide Wall Mounted Grab Bar SGB
1-1/2" (38 mm)
bar diameter
1 2 3 4
Need Help?
Symmons customer service:
(
800) 796-6667, (781) 848-2250
customerservice@symmons.com
Mon - Fri 7:30 am - 7:00 pm EST
www.symmons.com/service
• Technical help
• Product information
• Warranty policy
Six (6) #10 x 2-1/2"
(63.5 mm) wood
screws included and
two (2) spacers
drill hole
5/32 inch
press-on screwless
escutcheon
Grab Bar must be
secured with at least
two (2) of three (3)
screws at each end.
two (2) spacers
3" (77 mm)
diameter
1-1/2" (38 mm)
standard wall
stud width

Installation Notes
Grab Bar Location
For proper mounting heights and location
having jurisdiction over the installation.
Solid Support
■ Grab Bar must be mounted with both
ends positioned over a wall stud. A stud
■ Secure through wall board or tile to the
wall stud so as to hold a minimum of
250 pounds of force.
■ At least two (2) of the three (3) screws
provided must be used on each end of
the Grab Bar to properly secure.
Note: Standard size wall stud limits
using more than two (2) screws.
Mounting Grab Bar
■ Drill all holes through wall board into
wood wall studs using a power drill
and a 5/32 inch drill bit.
■ Ceramic tiles -
If installing Grab Bar
through the tile using a 1/4 inch carbide
tip drill bit to prevent damage to the tiles.
Next, drill a pilot hole into the wood wall
stud using the 5/32 inch drill bit.
Care and Cleaning
Mild soap and water or a non-abrasive
cleaner is recommended for cleaning.
Dimensions Wall Mounted Grab Bar, SGB
Grab Bar Length
Model Length
SGB-24 24" (610 mm)
SGB-36 36" (914 mm)
SGB-42 42" (1067 mm)
press-on screwless
escutcheon
1-1/2" (38 mm)
bar diameter
two (2) spacers
Six (6) #10 x 2-1/2"
(63.5 mm) wood screws
Grab Bar must be secured
with at least two (2) of three (3)
screws at each end.
Note: Dimensions subject to
change without notice.
grab bar length table
SGB-24........22-7/16" (582 mm)
SGB-36........34-7/16" (887 mm)
SGB-42........40-7/16" (1039 mm)
SGB-24........26-3/16" (666 mm)
SGB-36........38-3/16" (971 mm)
SGB-42........44-3/16" (1123 mm)
Reference
1-1/2" (38 mm)
standard wall stud width
3" (77 mm)
diameter
1-7/8" (x2)
(48 mm)
1-7/16" (x2)
(24 mm)
Symmons Industries, Inc. ■ 31 Brooks Drive ■ Braintree, MA 02184 ■ (800)796-6667, (781)848-2250 ■ Fax: (800)961-9621, (781)664-1300
©2013 Symmons Industries, Inc. ■ Printed in U.S.A. ■ www.symmons.com ■ customerservice@symmons.com ■ ZV-1088 ■ 111813