Sylvania Kingsley SRM769D-36FMC, SOM450D-36FACO User Manual

ELECTRIC FIREPLACE HEATER

KINGSLEY

Model :

SRM769D-36FMC

IMPORTANT:
PLEASE NOTE: WH EN YOU OPEN TH E CARTON, CAREFULLY CHECK

THE UNIT AND MAKE SURE THERE IS NO DAMAGE. IF YOU HAVE ANY
PROBLEMS WITH ASSEM BLING THE UNIT, WITH HOW THE VARIOUS
FUNCTIONS WORK OR WITH DAMAGE OR MISSING PARTS PLEASE CALL
1-800-459-4409 (EST) IMMEDIATELY FOR SERVICE.

NOTE: DO NOT RETURN UNIT TO THE STORE BEFORE CALLING THE TOLL
FREE NUMBER. DO NOT DISPOSE OF YOUR CARTONS UNTI L YOU ARE
COMPLETELY SATISFIED WITH YOUR NEW FIREPLACE HEATER.

NOTE: Light bulbs may become loose during shipping. If the flame effect is dim or
does not work, please check that light bulb or bulbs are finger tight in socket. See
instructions for replacing bulb or bulbs.

(CTC #64-3501)

5) Do not operate any electric fireplace heater if the cord or plug is damaged, or if
the heater malfunctions, or if it has been dropped or damaged in any manner.

6) Do not use outdoors.

7) This electric fireplace heater is not intended for use in bathrooms, laundry
areas and similar indoor locations. Never locate heater where it may fall into a
bathtub or other water container.

8) Do not run cord under carpeting. Do not cover cord with throw rugs, runners,
or similar coverings. Arrange cord away from traffic area and where it will not
be tripped over.

9) To disconnect electric fireplace heater, turn controls to off, then remove plug
from outlet.

10) Connect to properly grounded outlets only.

11) Do not insert or allow foreign objects to enter any ventilation or exhaust
opening as this may cause an electric shock or fire, or damage the heater.

12) To prevent a possible fire, do not block air intakes or exhaust in any manner. Do
not use on soft surfaces, like a bed, where openings may become blocked.

13) The heater has hot and arcing or sparking parts inside. Do not use it in areas
where gasoline, paint, or flammable liquids are used or stored.

14) Use this electric fireplace heater only as described in this manual. Any other use
not recommended by the manufacturer may cause fire, electric shock, or injury
to persons.

15) Avoid the use of an extension cord because the extension cord may overheat

SYLVANIA is a registered trademark of OSRAM SYLVANIA, used under license.

and cause a risk of fire. If you must use an extension cord, the cord must be
16 AWG and have a minimum rating of 1875 watts.

16) Caution: Do not plug this product into a receptacle controlled by a wall switch
or dimmer.

17) When storing or transporting the unit and cord, keep in a dry place, free from
excessive vibration and store so as to avoid damage.

CAUTION:
IF YOU USE THIS HEATER IN CONJUNCTION WITH A THERMAL CONTROL,

A PROGRAM CONTROLLER, A TIMER OR ANY OTHER DEVICE THAT
SWITCHES THE HEATER ON AUTOMATICALLY, REMEMBER TO OBSERVE
ALL SAFETY WARNINGS AT ALL TIMES. THE ELECTRIC FIREPLACE HEATER
HAS SAFETY OVERHEAT PROTECTION. IF THE OVERHEAT PROTECTION
TRIPS, SWITCH OFF ALL SWITCH BUTTONS AND WAIT APPROXIMATELY 5

-10 MINUTES. IT SHOULD RESET AUTOMATICALLY ONCE THE UNIT COOLS

DOWN.

INSTRUCTION MANUAL

ATTENTION:

1. Find a location for the electric fireplace heater that is protected from direct
sunlight.

2. Do not plug the unit into the power outlet before reading all instructions.

SAVE THESE INSTRUCTIONS FOR FUTURE USE.

IMPORTANT SAFETY INSTRUCTIONS

WHEN USING ELECTRICAL APPLIANCES, BASIC PRECAUTIONS SHOULD
ALWAYS BE FOLLOWED TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK,
AND INJURY TO PERSONS, INCLUDING THE FOLLOWING:

1) Read all instructions before using this electric fireplace heater.

2) This electric fireplace heater is hot when in use. To avoid burns, do not let bare

skin touch hot surfaces. The grill directly in front of the heater outlet becomes
hot during heater operation. Keep combustible materials, such as furniture,
pillows, bedding, papers, clothes, and curtains at least 3 feet (0.9 m) away from
the front of the unit and keep them away from the sides and rear.

3) Extreme caution is necessary when any heater is used by or near children

or invalids and whenever the electric fireplace heater is left operating and
unattended.

4) Always unplug electric fireplace heater when not in use.

WARNING:

Procedures and techniques if not carefully followed will result in damage to the
equipment and will expose the user to the risk of serious injury, illness or death.
This electric fireplace heater is for use on 120 volts. The cord features a three-prong
plug as shown at “A” in illustration below. An adapter, as shown at “C”, is available
for connecting a three-prong grounded type plug to a two-slotted wall receptacle.
The green grounding plug extending from the adapter must be connected to a
permanent ground, such as a properly grounded outlet box. The adapter should not
be used if a three-slot grounded receptacle is available.

A 15 AMP circuit is required to operate this heater. If the breaker trips when the
heater is used then you may need to move the heater to another location or unplug
other appliances that are on the same circuit. If you require an extension cord use
one that is rated at 1875 watts.

1

IMPORTANT:

Please note when you open the carton carefully check the unit and make sure there
are no damages. If you have any problems with the unit, with how the various
functions work or with hidden damages or missing parts, please call: 1-800-459-

4409 (EST) for customer service. NOTE: DO NOT RETURN UNIT TO THE STORE
BEFORE CALLING THE TOLL FREE NUMBER. Do not dispose of your packaging
cartons until you are completely satisfied with your new electric fireplace
heater. Read all instructions thoroughly before operating your new electric
fireplace heater.

NOTE: Light bulbs may become loose during shipping. If the flame effect is dim or

does not work, please check that light bulb or bulbs are finger tight in socket. See
instructions for replacing bulb or bulbs.

NOTE: The electric fireplace heater may emit a slight harmless odor when first turned
on. This is caused by activating the internal heater components for the first time and
should not occur again.

fig. B

After reading complete instructions, confirm all controls on fireplace are in the OFF
position. Plug the fireplace into a 15AMP/120Volt outlet. If the cord does not reach,
you may use an extension cord rated for a minimum of 1875 watts. Once the fireplace
insert has been properly connected to a grounded electrical outlet, it is ready to
operate.

ASSEMBLY INSTRUCTIONS

PARTS LIST

Z. WALL ANCHOR SAFETY CABLE

Wall Anchor ......................................................................................................................... 1

Screw for wall anchor ....................................................................................................... 1

Screw for mantel ............................................................................................................... 1

Safety cable ........................................................................................................................ 1

CAUTION: Carefully move the assembled unit to the desired location. The fireplace
mantel should not be positioned in an area exposed to direct sunlight.

WALL ANCHOR SAFETY CABLE

The use of wall anchor safety cable is highly recommended in order to reduce the
risk of the fireplace being tipped over accidentally. WARNING: This cable may reduce
possible risk of injury if the fireplace is improperly handled, but is not a substitute for
proper adult supervision. Children should not be left unattended near any heater.

1. Drill a 5/16” (8 mm) hole in the wall. Insert the plastic wall anchor into the hole and

gently tap until the flange on the anchor is against the wall surface.

2. Position the back edge of the mantel close to the wall.

3. Attach the safety cable to the mantel using the screw for mantel. See fig. A and B.

4. Use the screw for wall to attach the other end of safety cable to the wall.

5. Make sure all screws are tight.

OPERATION BY THE CONTROL PANEL

The controls are located behind the grill below the front glass and can be accessed by
pulling the grill from the top, forward and down.

fig. A

0/I: Press this button for main power and flame effect. The indicator light will be on.
See below for other control switches.

1250W: For heat function - Press this switch while the 0/I switch is in the ON position.
The indicator light will be ON.

Temperature Control: To adjust the temperature to your individual requirements,
turn the temperature control dial to the right (clockwise) to increase the desired
temperature and to the left for lower temperature. This temperature control dial can
only be used while the 0/I switch and 1250W switches are in the ON position.

Note: When the O/I switch is turned off, all other heater functions will stop even
though the switches may be in the on position.

2