EN
Time mode
Training / Speed and
Distance mode
Logbook
Shortcuts
Total of all training
Backlight
2 sec
Switches
between
the modes
Enters and exits the
Settings and other
submodes
Starts and stops
the stopwatch
Shortcuts
Resets the
stopwatch
Backlight
2 sec
Switches
between
the modes
WELCOME
Congratulations on choosing Suunto t3 as your training partner. The Suunto t3
is a high-precision heart rate monitor designed to make your training as efficient
and enjoyable as possible.
Suunto t3 goes beyond conventional heart rate monitors by showing Training
Effect (TE). Training Effect tells you in real time how much a workout improves
your condition. It ensures that every workout you do takes you closer to your
targets, and gives you the freedom to work-out without pre-set heart rate (HR)
zones. Read more about Training Effect in Section 2.3.
With Suunto t3 you can also accurately measure the calories you burn, record
your workouts for post-training analysis and keep track of your long-term progress.
Suunto t3's functionality is maximized with optional Suunto PODs, wireless
sensors that measure speed and distance in different sports activities. You also
have the benefit of interference-free digital transmission of heart rate and speed
data.
This users guide is here to help you get the most out of your training with Suunto
t3. Please read through it to make using your new Suunto t3 even more productive.
EN
1. Getting started ... . . . . ... . . . . ... . . . . ... . . . ... . . . . ... . . . . ... . . . . ... . . . ... . . . . ... . . . . ... . . . . 4
1.1. Setting up Suunto t3 .. ... . . . . ... . . . . ... . . . ... . . . . ... . . . . ... . . . . ... . . . ... . . . . ... . . . . 5
1.2. Activity class (act class) .. ... . . . ... . . . . ... . . . . ... . . . . ... . . . ... . . . . ... . . . . ... . . . . ... 5
1.3. Suunto t3 at a glance ... . . . ... . . . . ... . . . . ... . . . . ... . . . ... . . . . ... . . . . ... . . . . ... . . . .. 7
1.3.1. Time mode ... . . . ... . . . . ... . . . . ... . . . . ... . . . ... . . . . ... . . . . ... . . . . ... . . . . .. . . . . . 9
1.3.2. Training mode . . . . ... . . . ... . . . . ... . . . . ... . . . . ... . . . ... . . . . ... . . . . ... . . . . ... . . 11
1.3.3. Speed and Distance mode ... . . . . ... . . . . ... . . . . ... . . . . ... . . . ... . . . . ... . . . . . 12
1.3.4. Settings . . . ... . . . . .. . . . . ... . . . . ... . . . . ... . . . . .. . . . . ... . . . . ... . . . . ... . . . . .. . . . . . 12
2. Before training ... . . . . ... . . . . ... . . . ... . . . . ... . . . . ... . . . . ... . . . ... . . . . ... . . . . ... . . . . ... . . . 16
2.1. The heart rate transmitter belt and speed and distance PODs .. . . . . ... . . . .. 16
2.1.1. Putting on the heart rate transmitter belt .. . . . . .. . . . . ... . . . . ... . . . . ... . . . . 16
2.1.2. Wireless speed and distance PODs . ... . . . . ... . . . . ... . . . ... . . . . ... . . . . ... 18
2.2. Settings ... . . . . ... . . . . ... . . . ... . . . . ... . . . . ... . . . . ... . . . ... . . . . ... . . . . ... . . . . ... . . . .. 18
2.2.1. Time mode settings .. . . . . ... . . . . ... . . . . ... . . . ... . . . . ... . . . . ... . . . . ... . . . ... . 18
2.2.2. Training mode settings ... . . . . ... . . . . .. . . . . ... . . . . ... . . . . ... . . . . .. . . . . ... . . . 20
2.2.3. Speed and Distance mode settings . . . . ... . . . . ... . . . ... . . . . ... . . . . ... . . . . . 23
2.3. Training Effect . . ... . . . . ... . . . . ... . . . ... . . . . ... . . . . ... . . . . ... . . . ... . . . . ... . . . . ... . . . 25
3. Training . ... . . . . ... . . . . ... . . . . ... . . . ... . . . . ... . . . . ... . . . . ... . . . ... . . . . ... . . . . ... . . . . ... . . . 27
3.1. Using Training Effect targets ... . . . . ... . . . . ... . . . . ... . . . ... . . . . ... . . . . ... . . . . ... . 28
3.2. Training without set targets . ... . . . . ... . . . . ... . . . ... . . . . ... . . . . ... . . . . ... . . . ... . . . 28
3.3. Using the speed and distance displays ... . . . . .. . . . . ... . . . . ... . . . . ... . . . . .. . . . . 30
4. After training . . ... . . . . ... . . . . ... . . . ... . . . . ... . . . . ... . . . . ... . . . ... . . . . ... . . . . ... . . . . ... . . . 31
4.1. Training Logbook . . . . ... . . . . .. . . . . ... . . . . ... . . . . ... . . . . .. . . . . ... . . . . ... . . . . ... . . . . 31
4.2. Training Totals .. . . . . ... . . . . ... . . . . ... . . . . .. . . . . ... . . . . ... . . . . ... . . . . ... . . . ... . . . . .. 32
2
4.3. Suunto Training World ... . . . . ... . . . . ... . . . ... . . . . ... . . . . ... . . . . ... . . . ... . . . . ... . . 34
5. Care and maintenance . . . . ... . . . ... . . . . ... . . . . ... . . . . ... . . . ... . . . . ... . . . . ... . . . . ... . . . 34
5.1. General instructions .. . . . ... . . . . ... . . . . ... . . . . ... . . . ... . . . . ... . . . . ... . . . . ... . . . ... 34
5.2. Water resistance . . . . . ... . . . . ... . . . . .. . . . . ... . . . . ... . . . . ... . . . . .. . . . . ... . . . . ... . . . . 35
5.3. Changing the strap length . . . . ... . . . . ... . . . . ... . . . ... . . . . ... . . . . ... . . . . ... . . . ... . 35
5.4. Replacing the battery ... . . . . ... . . . . .. . . . . ... . . . . ... . . . . ... . . . . ... . . . ... . . . . ... . . . . 36
5.4.1. Replacing the battery of the Suunto t3 .... . . . ... . . . . ... . . . . ... . . . . ... . . . . 37
5.4.2. Replacing the battery of the heart rate belt ... . . . ... . . . . ... . . . . ... . . . . ... 38
6. Technical specifications .. . . . ... . . . . ... . . . . ... . . . . ... . . . ... . . . . ... . . . . ... . . . . ... . . . ... . 39
7. Intellectual property .. . . . ... . . . . ... . . . . ... . . . . ... . . . ... . . . . ... . . . . ... . . . . ... . . . ... . . . . .. 40
7.1. Copyright . . . .. . . . . ... . . . . ... . . . . ... . . . . .. . . . . ... . . . . ... . . . . ... . . . . .. . . . . ... . . . . ... . 40
7.2. Trademark . . . . . ... . . . . ... . . . . ... . . . ... . . . . ... . . . . ... . . . . ... . . . ... . . . . ... . . . . ... . . . . 41
7.3. Patent notice . . ... . . . . ... . . . . ... . . . ... . . . . ... . . . . ... . . . . ... . . . . .. . . . . ... . . . . ... . . . . 41
8. Disclaimers . . . ... . . . . ... . . . . ... . . . ... . . . . ... . . . . ... . . . . ... . . . ... . . . . ... . . . . ... . . . . ... . . . . 41
8.1. User's responsibility . . . . .. . . . . ... . . . . ... . . . . ... . . . . .. . . . . ... . . . . ... . . . . ... . . . . .. . . 41
8.2. Warnings . . . . . ... . . . . ... . . . ... . . . . ... . . . . ... . . . . ... . . . ... . . . . ... . . . . ... . . . . ... . . . ... 42
8.3. CE . ... . . . ... . . . . ... . . . . ... . . . . ... . . . ... . . . . ... . . . . ... . . . . ... . . . ... . . . . ... . . . . ... . . . . 42
8.4. ICES . . . ... . . . . ... . . . . ... . . . . ... . . . ... . . . . ... . . . . ... . . . . ... . . . ... . . . . ... . . . . ... . . . . .. 42
8.5. Limits of liability and ISO 9001 compliance . . . . . ... . . . . ... . . . ... . . . . ... . . . . ... . 42
8.6. After sales service . . . . . ... . . . ... . . . . ... . . . . ... . . . . ... . . . ... . . . . ... . . . . ... . . . . ... . . 43
8.7. FCC compliance . . . . . ... . . . . ... . . . . ... . . . . .. . . . . ... . . . . ... . . . . ... . . . . .. . . . . ... . . . . 44
9. Disposal of the device . . . . ... . . . . .. . . . . ... . . . . ... . . . . ... . . . . .. . . . . ... . . . . ... . . . . ... . . . . 45
3
1. GETTING STARTED
2 sec
The buttons are named on the back of the device according to the functions they perform. However,
in this user's guide the names are simplified as shown in the table below.
Name in User's GuideName on back of device
UP+ / lap
ENTERMode
DOWN- / Light
BACKAlt / Back
STARTStart / Stop
In Totals and Logbook, small arrows on the screen indicate the buttons that you can navigate with.
The buttons' functions depend on the length of the press. A short press is less than 1 second, and
a long press is more than 2 seconds. Throughout this user's guide, the following symbols are used
to indicate short and long presses.
Short press
Long press
4
1.1. Setting up Suunto t3
Carry on setting up the time,
date, units and personal settings.
After this Suunto t3 will go into
Time mode and will be ready for
operation.
Adjust with UP and DOWN buttons.
Accept with ENTER button.
When you press a button on your new Suunto t3 for the first time, you will be asked to define some
basic settings. Use the UP and DOWN buttons to change the values, accept and move to the next
item by pressing the ENTER button.
The figure below shows you how to set up your device for the first time.
NOTE
Your maximum heart rate is determined using the formula 210 minus 0.65
times your age, which is automatically calculated from the date of birth that
you enter. If you know your real maximum heart rate, you should use that
instead of the calculated value.
1.2. Activity class (act class)
Important: Your activity class is another one of the settings that you are asked to define when
you set up your device for the first time. Your activity class is a measure of your current activity
level. By entering your current activity class (1 - 10) into your Suunto t3, the device will be able to
give much more accurate calorie consumption information. As the amount and/or intensity of your
5
physical activity increases, the device will automatically increase your activity class based on your
recorded heart rate information. Your activity class will not be automatically decreased if, for
example, you engage in less strenuous activity, but you should manually decrease your activity
class if you think that it has decreased over time. See the table below for information on determining
your activity class.
Activity classActivity description
recreational sports or heavy physical
activity.
work requiring modest physical
activity, such as yard work, nordic
walking or moderate-intensity cycling.
physical exercise, such as running,
aerobic classes or high-intensity
cycling.
exercise sufficiently to cause heavy breathing or
perspiration.
0Always avoid exertion, whenever possible.No regular participation in
1Walk for pleasure, routinely use stairs, occasionally
210 - 60 minutes per weekRegular participation in recreation or
3Over 1 hour per week
4Less than 30 minutes per weekRegular participation in heavy
530 - 60 minutes per week
61 - 3 hours per week
7Over 3 hours per week
7.55 - 7 hours per weekEndurance athlete (Regional level)
87 - 9 hours per week
8.59 - 11 hours per weekEndurance athlete (National level)
911 - 13 hours per week
6
level)
In Time mode you can:
- view the time
- go to log
- go to Totals
- go to Time settings
- change shortcuts
- connect to pc*
In Training mode you can:
- use the stopwatch
- view your heart rate
or Training Effect
- set the Training Effect
target
- go to Training settings
- change shortcuts
In Speed and Distance mode
you can:
- view speed
- view distance
- set the Training Effect target
- go to Speed and Distance
settings
- change shortcuts
Time mode
Training mode
Speed and Distance
mode
(if paired with POD)
Logbook
Totals
1.3. Suunto t3 at a glance
Activity classActivity description
9.513 - 15 hours per weekEndurance athlete (International
10More than 15 hours per week
7
NOTE
In any of the above modes, a long press of the ENTER button will take you to that mode's Settings
menu. In Time mode, a short press of the START button will take you to Logbook and a short
press of the UP button accesses Totals. The figure below shows the functionality of each of these
submodes.
8
* In order to connect your device to a PC, an optional Suunto PC POD and
Suunto software are required.
In Totals you can view
the total values of your
sessions for:
- this week
- last week
- 6 last months
In Logbook you can view
your last 15 activities’:
- Training Effect
- duration
- calories consumed
- average heart rate
- peak heart rate
- time spent in and out of
zones or limits
Each mode has its own
settings menu where you
can define the settings
related to that mode.
Totals
Logbook
Settings menu
1.3.1. Time mode
Here you can see the functionality of the buttons used in Time mode. This will help you get started
with using the basic functions of your Suunto t3. Additionally, you will find options for the shortcut,
which is in the bottom line of the display.
9
2 sec
GO TO TOTALS
LIGHT
CHANGE SHORTCUT:
- DAY
- DATE
- DUAL TIME
- CONNECT TO PC (LONG PRESS)
GO TO TIME SETTINGS
GO TO LOGBOOK
The light
Pressing the BACK
button switches off
the alarm.
The light can be activated in any mode at any point by short pressing the DOWN button. If you
want to use the light in Settings, Logbook or Totals, the light must be activated before entering
them.
The alarm snooze
Only the BACK button deactivates the alarm; pressing any other button activates the snooze
function, which lasts for 5 minutes. The snooze function can be activated 12 times, after which the
alarm will be deactivated until the set time the following day.
10
1.3.2. Training mode
LAP/RESET (LONG PRESS)
CHANGE SHORTCUT:
- TRAINING EFFECT
AND DURATION
- TIME
- CALORIE CONSUMPTION
GO TO TRAINING SETTINGS
LIGHT
- CHANGE TRAINING
EFFECT TARGET (LONG PRESS)
START/STOP
2 sec
- AVERAGE HEART RATE
- LAP / INTERVAL TIME
- SPEED
- DISTANCE
(IF CONNECTED TO POD)
Pressing the
START/STOP
button starts
the stopwatch.
Pressing the
START/STOP
button again,
stops the
stopwatch.
Here you can see the basic functionality of the buttons used in Training mode as well as options
for the shortcut, which is in the bottom line of the display.
The stopwatch is accessed by pressing the START button in Training mode and can be seen in
the top row. The information from the training that you time with the stopwatch, such as heart rate
and calorie consumption, is stored and can later be seen in Totals and Logbook. Therefore, you
should activate the stopwatch, and ensure you have a heart rate reading, whenever you
start a training session.
While the stopwatch is running, you can take up to 99 lap times, the first 50 of which are stored
in the memory, by pressing the UP button.
11
1.3.3. Speed and Distance mode
LAP/RESET (LONG PRESS)
CHANGE SHORTCUT:
- DAYTIME
- AVG SPEED
- DISTANCE
GO TO SPEED AND
DISTANCE SETTINGS
LIGHT
- CHANGE TRAINING EFFECT
TARGET (LONG PRESS)
START/STOP
2 sec
- CHRONO
- ALSO HR RELATED
SHORTCUTS, IF
HR BELT IS ON
UP/ADJUST
RIGHT/EXIT ( L ONG PRESS)
D O WN/ADJUST
LEFT
The Speed and Distance mode is available when you have paired an optional speed and distance
POD with your Suunto t3. Here you can see the functionality of the buttons used in Speed and
Distance mode.
1.3.4. Settings
Navigating in the Settings menus is very easy. Follow the position of the blinking empty box and
you will know exactly where in the Settings menu you are.
Take a look at the following tables showing the different Settings and the items you can define in
them.
12
Time mode settings
Alarm
OptionsSettingSymbol
on/off
Alarm time: hour/minAlarm:
Time
General
hours/
minutes/
seconds
Date: year/ month/ dayDate
Tones:
on/off
Dual time: hours/ minutesTime:
HeightWeightPersonal
Heart rate:
bpm/ %
Activity
class
Height:
cm/ft
rate
Weight:
kg/lb
Time:
12h/24h
Date of birthSexMax heart
Date:
ddmm/
mmdd
Speed:
km/h,
mph,
time/km,
time/mile
13
Training mode settings
Heart
rate
zones
Heart
rate limits
Intervals
POD
General
14
OptionsSettingSymbol
Zone 1:
lower/
upper %
rate
limits: on/
off
Interval
1: on/off
Pair: heart rate belt / Foot POD / Bike POD / GPS PODPair a
Tones:
on/off
upper %
Lower limitHeart
Interval 1:
minutes/
seconds
Heart rate:
bpm/ %
Zone 3: upper %Zone 2:
limit
Interval 2:
on/off
Height:
cm/ft
Alarm: on/offUpper
Interval 2:
minutes/
seconds
Weight:
kg/lb
Warm
up: on/
off
Time:
12h/24h
Warm up: minutes/
seconds
Speed:
Date:
km/h,
ddmm/
mph,
mmdd
time/km,
time/mile
Speed and Distance mode settings
OptionsSettingSymbol
Autolap
on/off
DistanceAutolap:
Speed
POD
General
Limits:
on/off
Calibrate: Foot POD/ Bike PODCalibrate
Pair: heart rate belt / Foot POD / Bike POD / GPS PODPair a
Tones:
on/off
limit
Heart
rate:
bpm/ %
Upper limitLower
Height:
cm/ft
Weight:
kg/lb
Time:
12h/24h
Date:
ddmm/
mmdd
Speed:
km/h,
mph,
time/km,
time/mile
Please refer to Section 2.2 Settings for more information on how to define the device's settings.
15
2. BEFORE TRAINING
2.1. The heart rate transmitter belt and speed and distance PODs
2.1.1. Putting on the heart rate transmitter belt
The heart rate transmitter belt is an integral part of Suunto t3's functionality, so it's important that
you know how to wear it correctly.
We recommend that you wear the transmitter against your bare skin to ensure flawless operation.
•
The electrodes must be wet during the exercise. Raise the transmitter a little off your chest
and moisten the electrode area on the side in contact with your skin.
•
Check that the wet electrode areas are firmly against your skin and that the logo is in a central
upright position.
•
Enter Training mode. (Your heart rate will not be visible until you enter Training mode.)
Whenever you enter Training mode or start the stopwatch, your Suunto t3 automatically searches
for signals from a heart rate belt or paired speed and distance POD.
16
After switching to Training mode,
Suunto t3 displays two bars while it is
seeking the HR belt signal.
Instead of your heart rate, "00" is
shown in the center of the display if no
heart rate belt is found.
Once the device has found the signals, your heart rate or speed and distance information will be
displayed in the center of the screen.
NOTE
For detailed instructions on how to pair and calibrate your optional speed
and distance POD, please refer to the POD's own user's guide.
Heart rate signal troubleshooting
If you can't see a heart rate signal, or lose the signal, try these steps to fix the problem.
•
Exit and then re-enter Training mode.
•
Make sure that you are wearing the heart rate transmitter belt correctly. (See section 2.1.1.)
•
Ensure that the electrode area on the back of the belt is slightly wet.
•
If you have been using the belt for some time, the battery may need changing. For instructions
on how to change the transmitter belt's battery, see section 5.
17
2.1.2. Wireless speed and distance PODs
Use UP and DOWN buttons
to toggle between the
following time setting
submenus: alarm, time, date,
personal, general.
2 sec
Long press the
ENTER button to
switch between
Time mode and
settings.
Optional wireless speed and distance PODs are light, easy-to-use, and accurate. Since the devices
(Suunto Foot POD, Suunto Bike POD, and Suunto GPS POD) differ from each other, they come
with separate user's guides, which you should read for more detailed information on their use.
When you have paired and calibrated a speed and distance POD with your Suunto t3, you can
take advantage of the Speed and Distance mode, as well as speed and distance-related control
functions and information.
2.2. Settings
Before you are able to make the most of your Suunto t3, it's worth taking some time to personalize
it to suit your individual needs and preferences. If you have already defined the settings based on
the information given in section 1, you can skip to section 3.
2.2.1. Time mode settings
This figure shows how to enter the Time mode Settings menu and its different items.
NOTE
18
Remember that you can see where you are within the Settings menu by
following the flashing bar in the navigational aid.
Alarm settings
Continue setting your height,
activity class, maximum heart rate,
sex and birth date.
Adjust the weight setting with
UP and DOWN buttons. Accept
with ENTER button.
In the Alarm menu, you can set the alarm on or off and set the alarm time. Accept the settings
with a short press of the Enter button, which also moves you on to the next menu item.
Time settings
In the Time menu, you can set the time and dual time. Accept the settings with a short press of
the Enter button, which also moves you on to the next menu item.
Date settings
In the Date menu, you can set the day, month, and year. Accept the settings with a short press of
the Enter button, which also moves you on to the next menu item.
Personal settings
In the Personal menu, you can enter personal information such as your weight, height, activity
class, maximum heart rate, gender, and date of birth. Accept the settings with a short press of the
Enter button, which also moves you on to the next menu item.
19
NOTE
Use UP and DOWN buttons
to toggle between the
following Training setting
submenus: heart rate zones,
heart rate limits, intervals,
pair a POD and general.
2 sec
Long press the
ENTER button in
Training mode to
enter Training
settings menu.
See the table in Section 1.2, Activity class for information on activity class
descriptions.
General settings
In the General menu, you can set the button tones on or off and choose the units and format the
information is displayed in. Accept the settings with a short press of the Enter button.
2.2.2. Training mode settings
This figure shows how to enter the Training mode Settings menu and its different items.
Heart rate zone settings
In the Heart Rate Zone menu, you can define the 3 heart rate zones and set the tones on or off.
The 3 heart rate zones are useful in training as they record how much of your training is spent
within specific heart rate zones, or if you want to give yourself a long enough warm-up, or keep
your heart rate at an optimum level for fat burning.
20
After training, you can see how much of the session was spent in each zone. Each zone is a range
of heart rates expressed as a percentage of your maximum heart rate (which is calculated based
on the age you enter in the Personal settings menu). Accept the settings with a short press of the
ENTER button, which also moves you on to the next menu item.
The default heart rates for zones 1-3 are 60-70%, 70-80%, and 80-90% of your maximum heart
rate, but if you are following a specially designed training program, enter the zone values that have
been tailored towards your individual goals. The benefits of training in each default zone are shown
in the table below.
zone
Zone 1
(Fitness
zone)
Zone 2
(Aerobic
zone)
Zone 3
(Threshold
Zone)
NOTE
60 - 70% of maximum heart
rate
70 - 80% of maximum heart
rate
80 - 90% of maximum heart
rate
The heart rate zone defaults follow the guidelines of the American College
of Sports Medicine for exercise prescription.
Main benefitDefault settingHeart rate
Improves your basic endurance, and helps you to recover from harder
training sessions. Can also be used in weight control.
Improves your aerobic capacity. This is the preferred zone if you are
training for an endurance event.
Improves your maximum aerobic capacity and lactate tolerance ability
(anaerobic threshold) - meaning your maximum endurance will
improve and you'll be able to fight fatigue better.
21
The average heart rate is also a useful measure during training where the heart rate levels vary
Target
heart rate
Lower limit
When the Limit alarm is on, Suunto t3
gives you an alarm when your heart
rate rises above the upper limit or
drops below the lower limit. The alarm
continues until you return to your
target heart rate range.
Upper limit
a lot, such as biking in hilly terrain. In these cases, the target zone limits are less practical than
the average heart rate.
Heart rate limit settings
In the Heart Rate Limit menu, you can set the heart rate limits on or off, define the upper and lower
limits, and set the heart rate alarm on or off. You can set the heart rate limits to help you stay within
a defined heart rate range, which you can set to match the goal of your training.
While training, your real-time heart rate can be displayed in the center of the screen. If the average
heart rate shortcut is selected, your real-time average heart rate per lap is displayed in the bottom
row as either beats per minute or a percentage of your maximum heart rate. In the Settings menu,
you can set alarms to notify you when you go above your set upper heart rate or below the set
lower heart rate.
By checking your average heart rate you can adjust your training intensity to make sure the session
is as effective as possible.
22
Intervals settings
Accept with the ENTER button then turn
on the POD you want to pair.
Select the POD you want to pair using
UP and DOWN buttons.
In the Intervals menu, you can set interval 1 and 2 on or off and define their times. You can also
set the warm-up timer on or off and define its time. Accept the settings with a short press of the
Enter button, which also moves you on to the next menu item.
Pair a POD settings
In the Pair a POD menu, you can pair your Suunto t3 with your heart rate transmitter belt, Suunto
PC POD, Suunto Foot POD, Suunto Bike POD or Suunto GPS POD.
NOTE
After pairing, enter Time mode and re-enter Training mode to view the
POD's readings.
General settings
See Section 2.2.1 Time mode settings for information on General settings.
2.2.3. Speed and Distance mode settings
To recap, this figure shows how to enter the Speed and Distance mode settings menu and its
different items.
23
Use UP and DOWN buttons
to toggle between the
following Speed and
Distance setting submenus:
autolap, speed, calibrate, pair
a POD and general.
2 sec
Long press the
ENTER button in
Speed and
Distance mode to
enter Speed and
Distance settings
menu.
Autolap settings
In the Autolap menu, you can set the autolap function on or off and set the distance for each lap.
When autolap is set on, and you have a paired speed and distance POD, the device beeps and
shows total distance, average lap speed, and lap time for 5 seconds with each lap.
Speed settings
In the Speed menu, you can set the speed limit on or off and define the upper and lower speed
limits.
Calibrate settings
In the Calibrate menu, you can calibrate your Suunto Foot POD or Suunto Bike POD. An alternative
way of calibrating your POD is to run or cycle a known distance, say 10 km, using the POD. If you
do not reset the stopwatch after completing the distance, you can correct the distance shown, for
example 9.6 km, from the settings. The device will then update the calibration value accordingly.
The GPS POD is also listed in the Calibrate menu but the calibration has no effect on the GPS
POD measurements. You will need this calibration only if you have, for instance, two Bike PODs
for different bikes. You can then pair one of them as GPS POD and use the calibration in the same
way as you normally would with Bike POD.
24
Pair a POD settings
See Section 2.2.2 Training mode settings for information on Pair a POD settings.
General settings
See Section 2.2.1 Time mode settings for information on General settings.
2.3. Training Effect
A unique feature of Suunto t3 is its ability to record and display Training Effect. Training Effect
(TE) shows the effect of a workout on your aerobic fitness on a simple one-to-five scale. For the
first time, you will know in real time how much your workout is really improving your fitness level.
With Training Effect, you can ensure that your workouts always give the intended result.
Please note the difference between training zone (temporary training intensity) and Training Effect
(total load of a workout). In zone training, you try to keep your heart rate at a certain level throughout
the whole workout, whereas for Training Effect it is enough just to reach the desired TE value once
during the workout.
Result of the workoutDescriptionMeasured TE
Minor TE1.0 - 1.9
Maintaining TE2.0 - 2.9
Improving TE3.0 - 3.9
Enhances recovery (short workout) or develops base endurance
(over 1 hour session). Ideal for fat burning. Does not improve
maximal performance.
Maintains aerobic fitness. Builds base for harder training in the
future. Does little to improve maximal performance.
Improves aerobic fitness if repeated 2–4 times a week. No
special recovery requirements.
25
Highly improving TE4.0 - 4.9
Long pressing the BACK
button switches between
heart rate and real-time
Training Effect.
2 sec
TE can be shown in the center
instead of heart rate.
TE graph + scale
If you continue your workout after
reaching the target, the bottom row
automatically starts showing
remaining time to the next TE level,
in this case 3.4.
This shortcut shows how much time you still have
to the next training effect level. In this example,
you need to continue 10 minutes at the current
intensity to reach TE 3.2.
Over-reaching TE5.0
Rapidly improves aerobic fitness if repeated 1–2 times a week.
A few easier exercise sessions (TE 1–2) needed for recovery.
Dramatic increase in aerobic fitness if adequate recovery is
allowed afterwards. High demand for recovery. Increased risk
of overtraining if repeated too often.
When monitoring your Training Effect, you no longer need to stay within pre-defined heart rate
zones because the TE shows the actual result of the workout regardless of what your exact heart
rate is. This gives you freedom from the zone alarms while still reaching the desired result.
Suunto t3 shows the Training Effect in two ways. The lower right side of the display shows it as a
graph. It can also be shown as a number in the center of the screen instead of the heart rate
reading. The TE of each workout is defined by the highest number (from 1.1 to 5.0) reached during
the workout. The peak TE reached stays visible on the graph. If you want to further increase the
effect after a lower intensity period, you need to work-out harder to push the peak higher.
26
Peak level. If there has been a period of
lower intensity, your current level may be
lower. To reach higher TE than 3.8 from this
workout, you need to increase the
intensity so that this graph pushes the
peak mark higher.
Training Effect reached so far in the
workout: 3.8 (Improving)
Bottom row: Next TE level is 4.0 but you can not reach it with the current
intensity. (Time indicator -:-- means that you have to increase intensity to
reach the target.)
To find out more about Training Effect, and how to use it to improve your training, please download
Heart beat analysis technology producing Training Effect is provided and supported
by Firstbeat Technologies Ltd.
Suunto Training Guidebook from www.suunto.com/training.
3. TRAINING
Once you have your Suunto t3 set up as you like it, it's time to get out and start training. For detailed
information on training and tips on how to maximize its effectiveness, download Suunto Training
Guidebook from www.suunto.com/training.
There are three alternative ways to use your Suunto t3 in training: using Training Effect targets,
training without targets, and using the speed and distance display.
27
3.1. Using Training Effect targets
2 sec
Long press the DOWN
button to increase the
Training Effect target.
Pressing the
START/STOP
button starts
the stopwatch.
Pressing the
START/STOP
button again,
stops the
stopwatch.
You can increase the Training Effect target by long pressing the DOWN button while the Training
Effect shortcut is displayed. This automatically updates the recommended duration of the session.
3.2. Training without set targets
The stopwatch is activated by short pressing the START button in Training mode. It can be seen
in the top row in Training mode. The information from the training that you time with the stopwatch,
such as heart rate and calorie consumption, is stored and can later be seen in Totals and Logbook.
Therefore, you should activate the stopwatch, and ensure you have a heart rate reading,
whenever you start a training session.
28
Pressing the UP button, when
the stopwatch is running, stores
the split time and displays it in
the top row of the Suunto t3. It
also displays the average heart
rate and shows the lap time.
After 3 seconds, the display
jumps back to the stopwatch.
This number
indicates the
ongoing lap.
While training, the stopwatch displays either the real-time Training Effect or heart rate in the center
Pressing the BACK button
changes the sho
rtcut at the
bottom of the display. Some
sho
rtcuts are only
available when connected
to speed and distance POD.
of the screen. You can switch between the two by long pressing the BACK button.
The information that is displayed while the stopwatch is running depends on the device's settings
as well as on whether there is a speed and distance POD connected. The default shortcut, which
appears on the bottom row of the display, is the Training Effect target. However, if you have set
an interval or warm-up timer on, lap time is the default shortcut and is shown as a countdown time
of the current interval. Short pressing the BACK button switches between shortcuts.
When the stopwatch has been stopped, you can reset it by long pressing the UP button, as shown
in the figure below.
29
Long pressing
the UP button
when the
stopwatch is
stopped resets
the stopwatch.
2 sec
If your peak heart rate in the most recent session exceeded the maximum heart rate defined in
If you want to update your
maximum heart rate, press the
DOWN button. Pressing the BACK
button takes you back to
Training mode without updating
your maximum heart rate.
Personal Settings, Suunto t3 will ask if you want to update your maximum heart rate value after
resetting the stopwatch.
3.3. Using the speed and distance displays
While training, the Speed and Distance mode provides additional information to help you monitor
and adjust your training. The top row displays distance information, the center row displays speed
information, (in whichever format was chosen in General settings), and the bottom row displays
different information depending on the shortcut selected.
30
Pressing the BACK
button changes
the sho
rtcut at
the b
ottom of
the disp
lay.
NOTE
If Autolap is set off, the average speed shown is the average speed from
the start of the previous lap and the lap time is the time from the start of
the last lap.
4. AFTER TRAINING
Once you have finished your training, your Suunto t3 can provide you with detailed information on
your performance. In this section, we'll look at the Totals and Logbook functions, as well as Suunto's
online training community, www.suunto.com/training.
4.1. Training Logbook
Immediately after finishing your training, one of the first things you'll want to do is review all the
data recorded during the session. You can see your Training Effect, peak heart rate, average heart
rate, how many calories you burned, speed and distance information (if using an optional speed
or distance POD) and more in the Logbook submode. The Logbook can be accessed by short
pressing the START button in Time mode. You can use the DOWN, UP, ENTER and BACK buttons
to navigate in the menu.
31
Press the ENTER button to scroll through the
logs. Use the UP and DOWN buttons to view
the summary of a particular log: Training
Effect, average and peak heart rate etc. Move
back in the summary using the BACK button.
Depending whether you had set the heart rate limits or heart rate zones on or off during the training,
the Logbook will display information relating to either heart rate zones or heart rate limits, or neither
if both were turned off or your Training Effect was less than 1.1.
The logbook stores all the information from your last 15 training sessions. After 15 logs have been
saved, the latest one will overwrite the oldest one. You cannot delete or modify logs in the memory.
If you are interested in more detailed, long-term analysis, you might be interested in Suunto's PC
software. You can use it to view in-depth figures, statistics, and graphical representations of all
the training sessions performed with your Suunto t3. Please see www.suunto.com/training for
more details.
4.2. Training Totals
In addition to detailed information on your last 15 training sessions, Suunto t3 stores all the
accumulated data recorded this week (Monday - Sunday), last week, and for the last 6 months.
This information can be seen in the Totals submode, which is accessed by short pressing the UP
button in Time mode.
32
When in the Totals submode, use the UP and DOWN buttons to choose the period you wish the
Pressing the ENTER button takes you through your
training totals for this week: number of workouts,
training time, calories etc.
Press the UP button in Time mode to view
the totals of your training. Long press ENTER
button to exit the Totals.
In each display, you can use the UP and DOWN
buttons to change between the view for this week,
last week, and for each month for the past 6
months.
Press the BACK
button to return to the
previous display.
view. The ENTER and BACK buttons are used to view the different totals, for example Training
Effect total, calorie consumption totals, and distance totals. The figure below shows how to navigate
within the Totals menu.
NOTE
Once you have reviewed your data, you can exit Totals by long pressing either the ENTER or
BACK button.
In the Week view of the Training Effect totals, as in the above figure, each
dot represents 15 minutes of training. In the Month view, each dot
represents one hour of training.
33
4.3. Suunto Training World
Suunto Training World, Suunto's training-specific Web site, is dedicated to helping athletes and
fitness enthusiasts at all levels achieve their goals. You'll find this site the perfect training partner
for running, cycling, aerobics, spinning, walking and the whole range of endurance and team
sports.
Whether you're working toward a marathon, or aiming for weight loss and a healthy heart, Suunto
Training World is a valuable resource for tips, news and inspiration.
Take a tour of the site at www.suunto.com/training. Learn about new Suunto training products,
gather training tips, participate in discussions, keep abreast of training news, and motivate yourself
with the stories of Suunto Ambassadors.
5. CARE AND MAINTENANCE
Your Suunto t3 is a precision instrument. By following a few common sense points, you can
maximize the life of your device. If your Suunto t3 does require servicing, you should take it to
your nearest Suunto representative. This section also describes the steps to follow when replacing
the battery in both your Suunto t3 and the transmitter belt.
5.1. General instructions
•
Only perform the procedures described in this user's guide.
•
Never attempt to disassemble or service your Suunto t3.
•
Always protect your Suunto t3 from shocks, hard and sharp objects, extreme heat and prolonged
exposure to direct sunlight.
•
If not in use, store your Suunto t3 in a clean and dry environment at room temperature.
•
In order to prevent the face from becoming scratched, the device should not be stored in the
bottom of a bag or other place where it could come into contact with hard objects.
34
•
You can wipe your Suunto t3 clean with a cloth lightly moistened with warm water. If there are
stubborn stains or marks, you can apply mild soap to the area.
•
Do not expose your Suunto t3 to strong chemicals, such as gasoline, cleaning solvents, acetone,
alcohol, insect repellents, adhesives and paint, as they will damage the unit’s seals, case and
finish.
5.2. Water resistance
Your Suunto t3 is water resistant up to 30 m/100 ft and the transmitter belt to 20m/66ft according
to ISO 2281 standard (www.iso.ch). This means that you can use your Suunto t3 for swimming
and other water sports activities but you must not use it for scuba diving or freediving.
To maintain water resistance and to ensure that the warranty remains valid, we strongly recommend
that you have all service, except for battery change, performed by authorized Suunto service
personnel.
NOTE
Never push the buttons while swimming or in contact with water. Pressing
the buttons while the unit is submerged could cause the unit to malfunction.
NOTE
Even though both the Suunto t3 and the transmitter belt are water-resistant,
the radio signal does not carry in water, which makes the communication
between Suunto t3 and the transmitter belt impossible.
5.3. Changing the strap length
The strap length of some Suunto t3 models can be adjusted for a perfect fit. Follow the steps
below:
•
Remove the buckle by releasing the spring bars with a pin, paper clip or other sharp object.
•
Remove both spring bars from the pin holes.
35
•
Shorten the strap by cutting along the grooves on the inner surface. You can do this for instance
with scissors. If you are unsure of the correct length, cut the pieces one by one and test the
length after cutting each piece. Cut in turns from both sides of the strap to keep the sides
equally long. Be careful not to shorten the strap too much.
•
Replace the spring bars into the last pin holes of both sides of the strap.
•
Attach the buckle to the strap by placing the spring bars into the holes in the strap. In both
sides of the buckle are holes for two different positions. This can be used for fine tuning of the
strap length. Make sure that the spring bars are positioned straight in the buckle.
5.4. Replacing the battery
You can replace the battery in both the Suunto t3 and the heart rate transmitter belt. In this section
we see how to do this.
36
Your Suunto t3 operates on a 3-Volt lithium cell, type: CR 2032. The life expectancy is approximately
12 months of operation with an average of 4 hours of training a week. The higher your average
amount of training hours a week, the shorter the battery's life expectancy will be.
NOTE
To reduce the risk of fire or burns, do not crush, puncture or dispose of
used batteries in fire or water. Only replace them with manufacturerspecified batteries. Recycle or dispose of used batteries properly.
5.4.1. Replacing the battery of the Suunto t3
To replace the battery:
1. Use a coin to open the battery compartment on the back of your device. Ensure that the O
ring and all surfaces are clean and dry.
2. Remove the old battery.
3. Place the new battery into the battery compartment with the positive side facing up.
4. Slide the battery gently against the contact plate on the side, ensuring that it does not break
or bend out of place.
5. When replacing the cover, rotate it carefully counter-clockwise with your thumb in order to
align the threads. The cover should rotate easily at first without having to use force. If you
have to use force right at the start, the threads are misaligned and the threads may be
damaged.
6. Perform the final tightening with a suitably sized coin.
NOTE
The markings on the cover may be left unaligned once the cover has been
tightened. If the old cover is undamaged, it does not need to be replaced.
37
NOTE
If the threads of the battery compartment cover are damaged, please send
your device to an authorized Suunto representative for service.
NOTE
NOTE
Replace the battery with extreme care to ensure that your Suunto t3 remains
water resistant. Careless battery replacement may void the warranty.
Heavy use of the backlight will significantly reduce battery life.
5.4.2. Replacing the battery of the heart rate belt
The average expected battery life of the transmitter belt is 300 hours of use in ideal operating
temperatures. If your Suunto t3 does not receive a signal when the transmitter belt is active, you
might need to replace the battery.
1.
Use a coin to open the battery compartment cover on the backside of the transmitter belt.
Ensure that the O ring and all surfaces are clean and dry. Do not stretch the O ring.
2.
Remove the old battery.
3.
Place the new battery into the battery compartment with the positive side facing up.
4.
With the O ring in the correct position, replace the battery compartment cover.
38
NOTE
We recommend that you replace the battery cover and the O ring
simultaneously with the battery to ensure that the transmitter remains clean
and water-resistant. Replacement covers are available with replacement
batteries.
NOTE
Battery covers of the transmitter belt and Suunto t3 are not interchangeable.
6. TECHNICAL SPECIFICATIONS
General.
• Operating temperature: -20°C to +60°C/-5°F to +140°F
• Storage temperature: -30°C to +60°C/-22°F to +140°F
• Weight: 45 g/50 g/65 g (depending on the strap)
• Water-resistance: 30 m/100 ft (ISO 2281)
• User replaceable battery CR2032
39
Calendar clock.
• Resolution: 1 s. Programmed until 2050
Stopwatch.
• Stopwatch range: 99 hours. Lap time range: 99 hours. Lap/split times: 50/log
• Resolution: 0.1 s
Heart rate data.
• Display range: 30 - 240 bpm
• Heart rate limits: 30 - 240 bpm
• Maximum heart rate for percentage display: 240 bpm
Transmitter belt.
• Water-resistance: 20 m/66 ft (ISO 2281)
• Weight: 61 g
• Frequency: 2.465 GHz Suunto ANT compatible
• Transmission range: Up to 10 m/30 ft
• User-replaceable battery: CR2032
7. INTELLECTUAL PROPERTY
7.1. Copyright
This publication and its contents are proprietary to Suunto Oy and are intended solely for the use
of its clients to obtain knowledge and key information regarding the operation of Suunto t3 products.
Its contents shall not be used or distributed for any other purpose and/or otherwise communicated,
disclosed or reproduced without the prior written consent of Suunto Oy.
40
While we have taken great care to ensure that information contained in this documentation is both
comprehensive and accurate, no warranty of accuracy is expressed or implied. Its content is
subject to change at any time without notice. The latest version of this documentation can always
be downloaded at www.suunto.com.
7.2. Trademark
Suunto, Suunto t3, Replacing Luck, their logos, and other Suunto brand trademarks and made
names are registered or unregistered trademarks of Suunto Oy. All rights are reserved. Firstbeat
& Analyzed by Firstbeat are registered or unregistered trademarks of Firstbeat Technologies Ltd.
All rights reserved.
7.3. Patent notice
This product is protected by the following patents and patent applications and their corresponding
national rights: US 11/432,380, US 11/181,836, US 11/169712, US 11/154,444, US 10/523,156,
US 10/515,170 and EU Design 000528005-0001/000528005-0010.
8. DISCLAIMERS
8.1. User's responsibility
This instrument is intended for recreational use only. Suunto t3 must not be used as a substitute
for obtaining measurements that require professional or laboratory-quality precision.
41
8.2. Warnings
If you have a pacemaker, defibrillator, or other implanted electronic device, you use the transmitter
belt at your own risk. Before you start using a transmitter belt, we recommend an exercise test
under a doctor’s supervision. This will ensure the safety and reliability of the pacemaker and
transmitter belt when used simultaneously.
Exercise may include some risk, especially for those who have been sedentary. We strongly advise
consulting your doctor prior to beginning a regular exercise program.
8.3. CE
The CE mark is used to mark conformity with the European Union EMC directives 89/336/EEC
and 99/5/ EEC.
8.4. ICES
This Class [B] digital apparatus complies with Canadian ICES-003.
8.5. Limits of liability and ISO 9001 compliance
If this product should fail due to defects in materials or workmanship, Suunto Oy will, at its sole
option, repair or replace it with new or rebuilt parts, free of charge, for two (2) years from the date
of its purchase. This warranty is only extended to the original purchaser and only covers failures
due to defects in materials and workmanship that occur during normal use while in the period of
the warranty.
It does not cover battery, battery replacement, damage or failures resulting from accident, misuse,
neglect, mishandling, alteration or modifications of the product, or any failure caused by operation
of the product outside the scope of its published specifications, or any causes not covered by this
warranty.
42
There are no express warranties except as listed above.
Suunto Oy and its subsidiaries shall in no event be liable for any incidental or consequential
damages arising from the use of or inability to use the product. Suunto Oy and its subsidiaries do
not assume any responsibility for losses or claims by third parties that may arise through the use
of this device.
Suunto's Quality Assurance System is certified by Det Norske Veritas to be ISO 9001 compliant
in all Suunto Oy's operations (Quality Certificate No. 96-HEL-AQ-220).
8.6. After sales service
If a claim under warranty appears to be necessary, return the product, freight prepaid, to your
Suunto representative who is responsible for having your product repaired or replaced. Include
your name, address, proof of purchase and/or service registration card, as required in your country.
The claim will be honored and the product repaired or replaced at no charge and returned in what
your Suunto representative determines a reasonable amount of time, provided that all necessary
parts are in stock. All repairs that are not covered under the terms of this warranty will be made
at the owner's expense. This warranty is non-transferable from the original owner.
Suunto's heart rate monitors can be registered online at www.suunto.com. Registering your unit
makes it quicker and easier for us to help you if you ever need to send your product for servicing,
or if you need information about using your unit from our Global Help Desk.
43
8.7. FCC compliance
This device complies with Part 15 of the FCC limits for class B digital devices. This equipment
generates, uses, and can radiate radio frequency energy and, if not installed or used in accordance
with the instructions, may cause harmful interference to radio communications. There is no
guarantee that interference will not occur in a particular instance. If this equipment does cause
harmful interference to other equipment, try to correct the problem by relocating the equipment.
Consult an authorized Suunto representative or other qualified service technician if you cannot
correct the problem. Operation is subject to the following conditions:
1.
This device cannot cause harmful interference.
2.
This device must accept any interference received, including interference that may cause
undesired operation.
Repairs should be made by authorized Suunto service personnel. Unauthorized repairs will void
the warranty.
Tested to comply with FCC standards.
For home or office use.
FCC WARNING: Changes or modifications not expressly approved by Suunto Oy could void your
authority to operate this device under FCC regulations.
44
9. DISPOSAL OF THE DEVICE
Please dispose of the device in an appropriate way, treating it as electronic waste. Do not throw
it in the garbage. If you wish, you may return the device to your nearest Suunto representative.
45
TWO YEAR WARRANTY
in material and/or workmanship to
This product is warranted to be free of
defects
original owner for the above noted period
the
not include battery life). Keep a copy
the original purchase receipt and make
of
(does
sure to get this warranty card stamped at
the place of purchase. The warranty
This warranty does not cover the
restrictions given in the instruction
warranties are limited and are subject to
the
originates from the date of purchase.
All
manual.
to the product resulting from
damage
usage, improper maintenance,
improper
neglect of care, alteration, improper battery
online at www.suunto.com.
heart rate monitors can be
registered
replacement or unauthorized repair.
Suunto's
Telephone E-mail
Signatur
e
Address
Ci t
y Countr y
Nam
e
Store
Store stamp with date of purchase
Place
Date
City Store Country
of purchase
of purchase/Store name
heart rate monitor
: number:
Model of Serial
CUSTOMER SERVICE CONTACTS
COORDONNÉES DU SERVICE CLIENTS, KUNDENDIENSTE, DATOS DE CONTACTO DE ATENCION
AL CLIENTE, NUMERI UTILI PER IL SERVIZIO CLIENTI, KLANTENSERVICE, ASIAKASPALVELUN
YHTEYSTIEDOT, KUNDSERVICE, KONTAKTER
Global Help Desk +358 2 284 11 60
Suunto USA Phone +1 (800) 543-9124
Canada Phone +1 (800) 776-7770
Suunto website
COPYRIGHT
This publication and its contents are proprietary to Suunto Oy.
Suunto, Wristop Computer, Suunto t3, Replacing Luck and their logos are registered
or unregistered trademarks of Suunto Oy. All rights reserved.
While we have taken great care to ensure that information contained in this
documentation is both comprehensive and accurate, no warranty of accuracy is
expressed or implied. Its content is subject to change at any time without notice.
www.suunto.com
Suunto Oy 5/2006
Loading...