SUUNTO Advizor User Manual [de, es, fr, it, en]

EN | FR | DE | ES | IT | NL | FI | SV

USERS GUIDE

1. 2.

10.9.

8.7.6.5.

4.3.

12.11.

13. 14.

22.21.

20.19.18.17.

16.15.

24.23.

25. 26.

34.33.

32.31.30.29.

28.27.

36.35.

37. 38.

46.45.

42.41.

44.43.

40.39.

48.47.

49.

50.

58.57.

56.

55.

54.53.

52.51.

59. 60.

USER’S GUIDE

CUSTOMER SERVICE CONT ACTS

Suunto Oy Phone +358 9 875870

Fax +358 9 87587301

Suunto USA Phone 1 (800) 543-9124

Canada Phone 1 (800) 776-7770 European Call Center Phone +358 2 284 11 60 Suunto Website

www.suunto.com

TABLE OF CONTENTS

CHAPTER 1 INTRODUCTION ......................................................... 6

1.1 GENERAL INFORMATION ............................................................................................ 6

1.2 MAIN FUNCTIONS (MODES)........................................................................................ 6

1.2.1 Water Resistance ............................................................................................ 6

1.2.2 Backlight Features .......................................................................................... 7

1.3 BUTTON FUNCTIONS................................................................................................... 7

1.3.1 The [Mode] Button ........................................................................................... 7

1.3.2 The [+] Button .................................................................................................. 7

1.3.3 The [-] Button................................................................................................... 7

1.3.4.The [Select] Button .......................................................................................... 8

1.4 LCD DISPLAY ................................................................................................................ 8

1.5 MEASUREMENTS AND UNITS ..................................................................................... 9

1.5.1 Selecting the Units of Measurement ............................................................ 10

1.6 PRESSURE SENSOR CALIBRATION ......................................................................... 11

1.7 CARE AND MAINTENANCE ........................................................................................ 11

1.8 SERVICE ....................................................................................................................... 11

1.8.1 Battery Replacement of the Wristop Computer .......................................... 12

1.8.2 Battery Replacement of the transmitter belt ............................................... 13

CHAPTER 2 HEART RATE MONITOR .......................................... 13

2.1 SUUNTO WRISTOP COMPUTER AND TRANSMITTER IN A WATER

ENVIRONMENT ........................................................................................................ 13

2.2 SUUNTO WRISTOP COMPUTER AND INTERFERENCE ........................................ 14

2.3 WARNINGS ..................................................................................................................14

2.4 CARE ............................................................................................................................15

2.5 ACTIVATING THE HEART RATE MONITOR .............................................................. 15

2.6 OPERATION ................................................................................................................. 16

2.6.1 How to Set the Target Zones of the Heart Rate Monitor............................. 17

2.7 STOPWATCH SUB MODE ........................................................................................... 18

2.7.1 How to Use the Stopwatch ........................................................................... 18

2.8 INTERVAL COUNTDOWN TIMER SUB MODE .......................................................... 20

2.8.1 How to Set the Countdown Timer ................................................................. 20

2.8.2 How to Start the Countdown Timer............................................................... 21

2.9 HRM MEMORY............................................................................................................. 22

CHAPTER 3 TIME MODE .............................................................. 24

3.1 HOW TO SET THE TIME.............................................................................................. 25

3.2 DAILY ALARM SUB MODE .......................................................................................... 26

3.2.1 How to Set the Daily Alarms ........................................................................ 26

3.3 DUAL TIME SUB MODE .............................................................................................. 27

3.3.1 Setting the Dual Time Function .................................................................... 27

CHAPTER 4 ALTIMETER MODE ................................................... 28

4.1 SETTING THE ALTIMETER .......................................................................................... 30

4.2 ALTITUDE DIFFERENCE MEASUREMENT SUB MODE........................................... 32

4.2.1 How to Start the Altitude Difference Measurement ..................................... 32

4.3 24-HOUR MEMORY SUB MODE ................................................................................ 33

4.4 LOGBOOK SUB MODE ................................................................................................ 33

4.4.1 Closer examination of the logbook............................................................... 35

4.4.2 How to Start and Stop a Logbook................................................................. 36

4.5 LOGBOOK HISTORY SUB MODE .............................................................................. 36

4.5.1 Clearing the Logbook History ....................................................................... 37

CHAPTER 5 BAROMETER MODE ................................................ 37

5.1 PRESSURE DIFFERENCE MEASUREMENT SUB MODE ....................................... 38

5.1.1 How to Start the Pressure Difference Measurement .................................. 39

5.2 4-DAY MEMORY SUB MODE ...................................................................................... 39

5.3 SEA LEVEL PRESSURE SUB MODE ......................................................................... 40

5.3.1 Setting the Sea Level Pressure .................................................................... 40

5.4 BAROMETRIC TREND INDICATOR........................................................................... 41

CHAPTER 6 COMPASS MODE...................................................... 42

6.1 BEARING TRACKING SUB MODE ............................................................................. 43

6.2 DECLINATION ADJUSTMENT SUB MODE ................................................................ 43

6.2.1 Setting the Local Declination ........................................................................ 44

6.3. CALIBRATING THE COMPASS .................................................................................. 44

CHAPTER 7 FREQUENTLY ASKED QUESTIONS ........................ 45

7.1 GENERAL .....................................................................................................................45

7.1.1 Is the Wristop Computer waterproof? .......................................................... 45

7.1.2 How long will the battery last? ...................................................................... 45

7.1.3 What do the segments on the circumference mean? ................................. 46

7.1.4 Why do the segments on the circumference go to the left

(counterclockwise)? ....................................................................................... 46

7.1.5 Why are there two symbols above the mode texts and

7.2 HEART RATE MONITOR.............................................................................................. 47

7.3 TIME .............................................................................................................................. 47

7.4 ALTIMETER...................................................................................................................47

what do they mean?...................................................................................... 46

7.2.1 What should I do if there is no heart rate reading? ..................................... 47

7.2.2 What is the longest time I can set in the timer? ......................................... 47

7.3.1 Why do the segments on the circumference increase and decrease

when I am in the Watch mode? .................................................................... 47

7.4.1 How do you clear the logbook? .................................................................... 47

7.4.2 How does the logbook self-erase? ............................................................... 47

7.4.3 How many logbooks can you record? .......................................................... 48

7.4.4 What is the duration readout?....................................................................... 48

7.4.5 What is the maximum capacity of total vertical ascent or descent

feet/meters in the logbook history? ............................................................... 4 8

7.4.6 If hiking from a level of 5,000 ft down hill to 3,000 ft and then back up to 8,000 feet, how is the Wristop Computer going to read this or average

it out? .............................................................................................................48

7.4.7 Why does the vertical ascent/descent measurement show different

readings even though I am inside and staying in the same room? ............. 49

7.5 BAROMETER ............................................................................................................... 50

7.5.1 What is the little box on the top left of the display? ...................................... 50

7.5.2 Does the Wristop Computer show future trends in weather conditions? ..... 50

7.5.3 What does “absolute pressure” and “relative pressure” mean? ................... 50

7.5.4 What is temperature compensation? ............................................................ 50

7.6 COMPASS .................................................................................................................... 51

7.6.1 What is the purpose of the rotating outer bezel?.......................................... 51

7.6.2 Where do I find the correct declination for my area so I can set my

Wristop Computer? ....................................................................................... 51

7.7 EFFECT OF AIR TEMPERATURE ON ALTITUDE MEASUREMENT........................ 51

8. SPARE PARTS AVAILABLE ...................................................... 54

9. ABBREVIATIONS ...................................................................... 55

10. COPYRIGHT AND TRADEMARK NOTICE ............................. 55

11. CE COMPLIANCE .................................................................... 56

12. LIMITS OF LIABILITY AND ISO 9001 COMPLIANCE ............ 56

13. DISPOSAL OF THE DEVICE ................................................... 56

CHAPTER 1 INTRODUCTION

1.1 GENERAL INFORMATION

The Wristop Computer is a reliable high precision electronic instrument, intended for recreational use. The outdoor enthusiast who enjoys venturing out into sports like skiing, kayaking, mountain climbing, hiking and biking can rely on the Advizor’s accuracy.

The ergonomically designed Advizor Wristop Computer weighs only 2 ounces (55 g) and features a large number style LCD display intended to be clearly visible in almost any condition.

Note: The Wristop Computer is not intended to be used as a substitute for professional or industrial precision measurements and should never be used to acquire measurements when skydiving, hang gliding, paragliding, gyrocopter riding and flying small aircraft.

IMPORTANT NOTE: A PULLOUT PAGE IS LOCATED ON THE FRONT COVER. THE PAGE GRAPHICALLY ILLUSTRATES AND IDENTIFIES THE PROPERTIES OF THE WRISTOP COMPUTER AND LCD DISPLAY. IT WILL FACILITATE THE USER’S UNDERST ANDING OF THE FUNCTIONS AND PROCESSES NECESSAR Y TO SETUP THOSE FUNCTIONS.

1.2 MAIN FUNCTIONS (MODES)

The Wristop Computer features five main functions: TIME, ALTIMETER, BAROMETER, COMP ASS, and HEART RATE MONITOR. Each function provides several sub modes further enhancing the usefulness to its owner. All main functions (modes) and sub modes are discussed in detail following this section.

Note: The Heart Rate Monitor is the premier feature of the Wristop Computer. Details regarding this function are shown in Chapter 2 of this guide.

1.2.1 Water Resistance

The Wristop Computer is waterproof to a depth of 30m/100ft.

Note: The Wristop Computer is not a dive instrument, therefore buttons should not be operated (put to use) while under water.

1.2.2 Backlight Features

The Wristop Computer has an electroluminescent backlight. This is initiated by pressing and holding the [Mode] button for 2 seconds. The backlight will remain on for 5 seconds. Pressing any button during this time will restart the 5 second period, continuing the backlight feature.

1.3 BUTTON FUNCTIONS

Four buttons are used to operate the Wristop Computer: [Mode], [+] (ON/OFF), [-] (Fast Cumulative), and [Select].

1.3.1 The [Mode] Button

Is located on the top right of the Wristop Computer.

• In the main mode level, pressing the [Mode] button allows the user to select or move from one main mode or function to the next (TIME, AL TI, BARO, COMP , HRM).

• In the sub mode level, pressing the [Mode] button returns the user to the main mode level.

• In the setup process, pressing the [Mode] button accepts the changes or preferences. Pressing the button again will return the user to the main mode level.

• Pressing the button for 2 seconds activates the backlight feature.

1.3.2 The [+] Button

Is located on the bottom right of the Wristop Computer.

• In the setup process, pressing the [+] button changes or scrolls the value upward.

• In the timing and recording functions, this button acts as a start/stop (On/Off) button.

• In the memory and logbook functions, this button advances through previous recorded screens.

1.3.3 The [-] Button

Is located on the bottom left of the Wristop Computer.

• In the setup process, pressing the [-] button changes or scrolls the value downward.

• Also known as the “Fast Cumulative” button, by pressing the [-] button in any of the main modes, except the compass

mode, the Wristop Computer will quickly access information about total vertical ascent/descent, number of runs completed as well as maximum, minimum and average heart rate of the current or last completed recording. In the compass mode, the [-] button locks the current bearing for 10 seconds.

• In the timing functions, this button acts as a reset or pause button.

• In the memory and logbook functions, this button backtracks through previously recorded screens.

1.3.4 The [Select] Button

Is located on the top left of the Wristop Computer.

• In the main mode level, pressing the [Select] button allows the user to enter into the sub modes of the particular function or return to the main mode the user is in.

• In the main mode or sub mode, pressing and holding the [Select] button for more than 2 seconds allows the user to enter the setup process.

• In the setup process, the [Select] button allows the user to move between settable units or values and determine preferences.

1.4 LCD DISPLAY

The display is designed to offer maximum clarity and simplicity and is divided into six distinct viewable areas.

• The Outer Circumference encompasses the outer boundary of the LCD display.

• A Barometric Trend Indicator provides a quick reference for analyzing and collating possible conditions in the weather.

• Field 1 displays values in either numbers or text depending on the mode or sub mode the user is in.

• Field 2 displays large numbers and/or related unit of measure within the function.

• The Mode Indicator bar displays the five main modes (functions) of the Wristop Computer (a triangle arrow is just below indicating the mode). The fifth main mode, HRM is displayed on the Outer circumference on the bottom right. When the one segment under “HRM” is lit, the mode is activated for viewing and selection purposes.

• Field 3 displays either numbers and/or text.

Barometer Trend Indicator

SELECT BUTTON

Mode Indicator

Field 1

Field 2

Bubble Level

MODE BUTTON

Outer Circumference

- BUTTON

Field 3

1.5 MEASUREMENTS AND UNITS

The Wristop Computer supplies two units of measure: metric or imperial.

Metric Unit of Measure

m/min

mbar

+ BUTTON

HRM Indicator

Imperial Unit of Measure

ft/min

InHg

1.5.1 Selecting the Units of Measurement

To change the unit s of measure displayed:

1. Check the mode indicator. If the mode arrow is not on TIME, PRESS the [Mode] button until the arrow is directly below TIME.

2. PRESS the [Mode] and [Select] buttons simultaneously and hold for 3 seconds. Field 1 will display “SET” momentarily and then display “UNI” (Fig. 1).

WARNING: If the user presses the [Select] button (and does not hold in for 3 seconds) while in the “UNI” setting mode, the user will be in the Pressure Sensor Calibration. Refer to the next sub-section for details.

3. PRESS the [Select] button and hold in for 2 seconds. Located to the right in Field 2, “m” or “ft” will begin to flash.

4. PRESS the [+] button to toggle between “m” and “ft”.

5. At the unit of measure desired, PRESS the [Select] button to move to the next unit. Located below the “m” or “ft” in Field 2, “mbar” or “inHg” will begin to flash.

6. PRESS the [+] button to toggle between “mbar” and “inHg”.

7. At the unit of measure desired, PRESS the [Select] button to move to the next unit. Located at the top right in Field 1 (just above the bubble),

8. PRESS the [+] button to toggle between °C and °F.

9. At the unit of measure desired, PRESS the [Select] button to move to the next unit. Located at the top center in Field 1, “m/min” or “ft/min” will begin to flash.

10.PRESS the [+] button to toggle between “m/min” and “ft/min”.

1 1.At the unit of measure desired, PRESS the [Mode] button to accept the changes. PRESS the [Mode] button again to

return to the main time mode.

Selecting the units of measurement is complete.

Note: If the user does not press any button for 1 minute in the setup mode, the display will automatically exit setup.

C or OF will begin to flash.

1.6 PRESSURE SENSOR CALIBRATION

WARNING: This is a F ACTOR Y CALIBRA TION SETTING. Do not enter this mode. If you enter this mode in error, exit immediately by pressing the [MODE] button to return to the “UNI” setting

mode. Normally there is no need to alter the calibration. If the Pressure Setting Calibration has been altered, you can return the factory setting. Proceed as follows: In

the calibration setting mode, scroll the barometric pressure value up or down until text “dEF” appears. This is the factory setting. Then exit by pressing [MODE].

1.7 CARE AND MAINTENANCE

Perform only the detailed processes discussed in this guide. Do not perform any other service to the Wristop Computer or attempt to open the case or remove the buttons or the bezel.

Protect your Wristop Computer from shocks, extreme heat and prolonged exposure to direct sunlight. If not in use, your Wristop Computer should be stored in a clean, dry environment at room temperature.

The Wristop Computer can be wiped clean with a lightly moistened (warm water) cloth. Applying a mild soap to the area can clean stubborn stains or marks.

Avoid exposing the Wristop Computer to strong chemicals like gasoline, cleaning solvents, acetone, alcohol, adhesives, and paint, as they will damage the unit’s seals, case and finish.

Never attempt to take the Wristop Computer apart or service it yourself. Make sure the area around the sensors (backside of the instrument) is kept free of dirt and sand. Never insert any objects into the sensor openings of the Wristop Computer.

1.8 SERVICE

When your Wristop Computer needs service, follow the instructions mentioned below. SENDING INSTRUCTIONS

1. Pack the product carefully to avoid damage.

2. Include both the Wristop Computer and the transmitter belt. A full periodic check will be done on the whole product.

3. Include proof of purchase (a receipt or its photocopy) if the product is under warranty.

4. Include a detailed description of the problem.

5. Include your name, return address and daytime telephone number.

6. Ship postage prepaid to your local Suunto dealer or distributor.

1.8.1 Battery Replacement of the Wristop Computer

The Wristop Computer operates on a three-volt lithium cell Type: CR 2430. The maximum life expectancy is approximately 12-18 months.

A low battery warning indicator is activated when 5-15 percent of the battery capacity is still available. When this occurs we recommend replacement of the battery.

Extreme cold weather may activate the low battery-warning indicator. Though the indicator is activated, the battery may not need to be replaced due to this condition. In temperatures above 10OC (50OF) if the low battery warning indicator is activated, the battery will need to be replaced.

Note: Heavy use of the electroluminescent backlight, the heart rate function, altimeter, and compass will significantly reduce the life of the battery.

To replace the battery:

1. flip over the Wristop Computer to view the backside;

2. insert a coin in the coin slot located on the battery compartment cover;

3. turn the coin counterclockwise to the open position marked on the back of the case;

4. remove the battery compartment cover;

5. remove the old cell from the battery compartment and ensure the O-ring and all surfaces are clean, dry and not damaged. Do not stretch the O-ring.

6. place the new cell into the battery compartment (negative side down, positive side up);

7. ensure that the O-ring is in place to keep the Wristop Computer waterproof and place the battery compartment cover back onto the backside of the Wristop Computer;

8. insert a coin back into the coin slot; and

9. turn the coin clockwise to the close position marked on the back of the case.

Note: Battery replacement should be performed with extreme care so as to ensure the Wristop Computer continues to remain waterproof. It is the operator’s responsibility to take due care to ensure that the Wristop Computer remains waterproof.

Note: After every battery replacement, it is necessary to calibrate the magnetic sensor. Details on performing this process are found in Calibrating the Compass section of this guide.

1.8.2 Battery Replacement of the Suunto Transmitter Belt

The Suunto transmitter belt battery’s average expected life is 300 hours. When the battery life has exhausted, the user can replace the battery by following the same instructions that are given concerning the battery replacement of the Wristop Computer.

CHAPTER 2 HEART RATE MONITOR

The transmitter features:

• Battery type: CR 2032 (replaceable by the user).

• Battery life: approximately 300 hours.

• Available in different sizes. The Suunto transmitter belt has to be sent along with the Wristop Computer in case of maintenance.

2.1 SUUNTO WRISTOP COMPUTER AND TRANSMITTER IN A WATER ENVIRONMENT

Suunto Wristop Computer is water proof to a depth of 30m/100ft. To maintain the water resistance, it is strongly recommended to have all service done by authorised Suunto service personnel.

Heart rate measurement in a water environment is technically demanding for the following reasons:

• Pool water with a high chlorine content and seawater may be very conductive and the electrodes of the transmitter may get short circuited and ECG (ECG = electrocardiogram) signals cannot be detected by the transmitter unit.

• Jumping into the water or strenuous muscle movement during competitive swimming may cause water resistance that

shifts the transmitter on the body to a location where it is not possible to pick up the ECG signal.

• The ECG signal strength varies depending on the individual’s tissue composition and the percentage of people who have problems with heart rate measurement is considerably higher in a water environment than in other use.

Note: The Wristop Computer is not a dive instrument, and therefore buttons should not be operated (put to use) while under water.

2.2 SUUNTO WRISTOP COMPUTER AND INTERFERENCE

ELECTROMAGNETIC INTERFERENCE Disturbances may occur near high voltage power lines, traffic lights, overhead lines of electric railways, electric bus lines

or trams, televisions, car motors, bike computers, some motor driven exercise equipment, cellular phones or when you walk through electric security gates.

Electromagnetic interference may cause inaccuracy in receiving heart rate signals. The sum of the “above”, “below” and “in” heart rate values may be shorter than the total elapsed time. The reason for this inaccuracy is that the electromagnetic interference may prevent the Wristop Computer from receiving signals of the transmitter belt perfectly.

2.3 WARNINGS

• Persons who have a pacemaker, defibrillator or other implanted electronic device use the Heart Rate Monitor at their own risk. Before starting the initial use of the Heart Rate Monitor, we highly recommend an exercise test under a doctor’s supervision. This will ensure the safety and reliability of the pacemaker and Heart Rate Monitor when simultaneously being used.

• Exercise may include some risk, especially for those who have been sedentary. W e strongly advise consulting your doctor prior to beginning a regular exercise program.

• Disturbances may occur near high voltage power lines, televisions, cars, bike computers, motor driven exercise equipment or cell phones.

• It is best to position the Wristop Computer within 3 feet or 1 meter of the transmitter. Ensure no other transmitters are within that range; signals from another transmitter(s) can cause an incorrect readout.

2.4 CARE

Wash the transmitter regularly with mild soap and water after each use. Rinse with pure water; dry thoroughly and carefully.

Store in a cool dry place. Never store the transmitter wet. Moisture keeps the electrodes wet and transmitter activated thereby shortening the life of the battery.

Do not bend or stretch the transmitter; this may damage the electrodes.

2.5 ACTIVATING THE HEART RATE MONITOR

1. Attach the transmitter to the elastic strap.

2. Adjust the strap length to fit snugly and comfortably. Secure the strap around your chest, below the chest muscles. Lock the buckle.

3. Raise the transmitter a little off your chest and wet the grooved electrode areas on the back of it. It is important that the electrodes are wet during exercise.

4. Check that the wet electrode areas are firmly against your skin and the logo is in a central upright position.

5. Wear the wristop computer as you would wear an ordinary watch.

Note: It is recommended that you wear the transmitter against your bare skin to ensure flawless operation. However, if you wish to wear the transmitter over a shirt, moisten the shirt well under the electrodes.

When the Wristop Computer is in the Altimeter main mode, HRM main mode or any of the HRM sub modes and the transmitter is worn, the Wristop Computer will automatically “search for” a heart rate signal. This procedure also initiates the heart rate measurement.

During the first minute, measurements are taken every second, then for the next 4 minutes every 5 seconds. If no heart rate signal has been received during the first five minutes, the “search for” a heart rate signal will end. After this process, the user can manually activate the heart rate measurement by pressing the [+] button in the HRM main mode.

NOTE: Pressing the [+] button during the first 5 minutes in the heart rate mode, will stop the search for a heart rate signal. To reactivate the measurement, press the [+] button again.

2.6 OPERATION

The Heart Rate Monitor function provides the user with:

• a heart rate range from 20 - 240 beats/min;

• a stopwatch range of up to 23:59.59, stores up to 30 split times and heart rate readings;

• an interval countdown timer range of up to 23:59.59;

• upper and lower limits adjustable in one beat increments to set target heart rate zone;

• audible alarms alert the user of exceeding upper or lower limit;

• heart rate displayed in relation to current time or running time (stopwatch and countdown timer);

• auto-repeat of countdown timer for interval training (training interval, recovery interval, number of intervals); and

• HRM memory activated from the starting of the stopwatch or the countdown timer storing total training time, maximum, minimum and average heart rate during training, as well as time spent in, above and below target heart rate zone. When stopwatch is used, the memory also stores up to 30 split times and heart rates for viewing.

To view and use the Heart Rate Monitor function: Check the LCD. If the segment under “HRM” is not highlighted, PRESS the [Mode] button until the segment directly

under “HRM” is lit. In the HRM mode (Fig. 2):

• Field 1 displays the text “HR” (HR = heart rate).

• Field 2 displays the current heart rate.

• Field 3 displays the current time.

Note: In order to activate this feature, the transmitter belt must be worn around the chest area. The middle row will show zero until there is a proper reading to display.

2.6.1 How to Set the Target Zones of the Heart Rate Monitor

To set the upper and lower limit s in the HRM mode:

1. PRESS the [Select] button and hold for 2 seconds.

• Field 1 displays the text “LI” (LI = Limits).

• Field 2 displays the text “OFF”.

2. PRESS the [+] button or the [-] button to toggle between off and on. Choose “On” to activate the audible heart rate limit alarms.

3. PRESS the [Select] button to move to the next setting (setting the upper limit) (Fig. 3).

• Field 1 displays the text “LI” (LI = Limits).

• Field 2 flashes the upper limit where the default value is 240.

• Field 3 displays the lower limit.

4. PRESS the [+] button to scroll the value upward or PRESS the [-] button to scroll the value downward.

5. At the value desired, PRESS the [Select] button to accept the upper limit value and move to the next setting (setting the lower limit) (Fig. 3).

• Field 1 displays the text “LI” (LI = Limits).

• Field 2 displays the new upper limit setting.

• Field 3 flashes the lower limit where the default value is 20.

6. PRESS the [+] button to scroll the lower limit value upward or PRESS the [-] button to scroll the value downward.

7. At the value desired, PRESS the [Mode] button to accept the upper and lower limits and exit.

The HRM target heart rate zone is set. Limits “On” means that the Wristop Computer will audibly alert the user that a chosen upper or lower limit has been

exceeded. Limits “OFF” means that the Wristop Computer will not alert the user, but the limits will however be used to calculate time spent in, above and below the target heart rate zone.

The outer circumference will graphically show the heart rate level reached by the user, in relation to the heart rate limit set. The circumference will adjust to equal any limit settings starting from the 12 o’clock position going clockwise. E.g. if the upper limit is set to 140 beats/minute and the lower limit to 130 beats/minute, one full circle on the outer circumference will equal 10 beats/minute.

2.7 STOPWATCH SUB MODE

The Wristop Computer stopwatch feature can provide split time measurement up to 23 hours 59 minutes and 59 seconds up to 30 split times and heart rate readings can be stored into the HRM memory.

In the HRM mode, PRESS the [Select] button once to enter this submode. In the Stopwatch mode (Fig. 4):

• Field 1 displays the seconds and tenths of a second,

• Field 2 displays the current heart rate, and

• Field 3 displays hours and minutes and to the far right “stopwatch”.

Note: When the transmitter is not worn, Field 2 displays the current time. The HRM memory for one event is automatically activated when starting the stopwatch (or countdown timer). The memory

stores total training time, maximum, minimum and average heart rate during training, as well as time spent in, above and below the target heart rate zone for one event. The next time the stopwatch (or countdown timer) is activated, the previous event’s information will be erased.

2.7.1 How to Use the Stopwatch

There are three timing modes the user can employ:

• an elapsed time measurement;

• a split time measurement; and

• a finish time measurement for up to 30 runners. In the elapsed time mode:

1. PRESS the [+] button to start, stop, and restart the stopwatch in the stopwatch sub mode.

2. PRESS the [-] button to reset the stopwatch to zero once the stopwatch has stopped. In the split time mode:

1. PRESS the [+] button to start the stopwatch.

2. PRESS the [-] button once to stop the stopwatch and to display a split time. This split time and the momentaneous heart rate reading will be stored in the memory for later viewing. The stopwatch will automatically start running after

displaying the split time for 5 seconds. Repeat this procedure for each split time.

3. PRESS the [+] button to stop the stopwatch.

4. PRESS the [-] button to reset the stopwatch to zero once the stopwatch has been stopped. In the two finish time mode:

1. PRESS the [+] button to start the stopwatch.

2. PRESS the [-] button once to stop the stopwatch and to display the first finish time. This finnish time will be stored in the memory for later viewing. The stopwatch will automatically start running after displaying the finish time for 5 seconds. Repeat this procedure for each runner.

3. PRESS the [+] button to stop the stopwatch.

4. PRESS the [-] button to reset the stopwatch to zero once the stopwatch has been stopped.

Note: If the user is in other modes or submodes when the stopwatch function is activated, the stopwatch will continue and remain in the background. A flashing “stopwatch” text in Field 3 indicates that the stopwatch is still activated.

2.8 INTERVAL COUNTDOWN TIMER SUB MODE

In the HRM mode, PRESS the [Select] button twice to enter this sub mode. In the interval countdown timer mode (Fig. 5):

• Field 1 displays the seconds,

• Field 2 displays the current heart rate, and

• Field 3 displays the hour and minutes with the text “TIMER” located to the right.

Note: When the transmitter is not worn, Field 2 displays the current time. The HRM memory for one event is automatically activated when starting the countdown timer (or stopwatch). The memory

stores total training time, training interval duration (1dur), maximum, minimum and average heart rate during training, as well as time spent in, above and below target heart rate zone for one event. The next time the countdown timer (or stopwatch) is activated, the previous event’s information will be erased.

There are two types of intervals: training and recovery. The countdown timer can be set to repeat a specific interval a specific number of times automatically. Adjustments to “training” interval, “recovery” interval and number of intervals can be made through the setup process.

Please note that the HRM memory will only store heart rate information for the “training” intervals.

2.8.1 How to Set the Countdown Timer

In the Interval Countdown Timer mode:

1. PRESS the [Select] button and hold in for 2 seconds. The first page is the training interval (Fig. 6).

• Field 1 displays the seconds;

• Field 2 displays the number “1” indicating the training interval and the number of intervals up to 99; and

• Field 3 displays the hours and minutes up to 23:59 and the text “TIMER”.

2. PRESS the [+] button to scroll the seconds upward or PRESS the [-] button to scroll the seconds downward.

3. At the seconds desired, PRESS the [Select] button to move to the next setting. Located on right of Field 3, the minutes will begin to flash.

4. PRESS the [+] button to scroll the minutes upward or PRESS the [-] button to scroll the minutes downward.

5. At the minutes desired, PRESS the [Select] button to move to the next setting. Located in the center of Field 3, the hour will begin to flash.

6. PRESS the [+] button to scroll the hour upward or PRESS the [-] button to scroll the hour downward.

7. At the hour value desired, PRESS the [Select] button to move to the next setting. Located in Field 2, the number of intervals can be chosen.

8. PRESS the [+] button to increase the number of intervals up to 99 or PRESS the [-] button to decrease the # of intervals desired. If no repeats of the interval are desired adjust this value to read 01.

9. At the number of intervals desired, PRESS the [Select] button to move to the second page. The second page is the recovery interval (Fig. 7).

• Field 1 displays the seconds;

• Field 2 displays the number “2” indicating the Recovery Interval; and

• Field 3 displays the hours and minutes up to 23:59 and the text “TIMER”.

10.PRESS the [+] button to scroll the seconds upward or PRESS the [-] button to scroll the seconds downward.

1 1. At the seconds desired, PRESS the [Select] button to move to the next setting. Located on right of Field 3, the minutes

will begin to flash.

12.PRESS the [+] button to scroll the minutes upward or PRESS the [-] button to scroll the minutes downward.

13.At the minutes desired, PRESS the [Select] button to move to the next setting. Located in the center of Field 3, the hour will begin to flash.

14.PRESS the [+] button to scroll the hour upward or PRESS the [-] button to scroll the hour downward.

15.At the hour value desired, PRESS the [Mode] button to accept the changes and exit the setup program.

The interval countdown timer setup for Training and Recovery is complete.

2.8.2 How to Start the Countdown Timer

During the training interval, the set heart rate limits are in use and the heart rate information is calculated and stored in the HRM memory. When the time has been counted down, a beep is heard, and simultaneously a new interval will begin.

If the recovery interval has a value other than zero, this interval will now be counted down. During the recovery interval the heart rate is displayed, but not measured nor stored for later calculations and will not effect max/min/average heart

rate readings nor the time spent in/above/below the target zone readings. The limits established are not in use during this interval either.

If the recovery interval has been set to “0”, another training interval is immediately started. This interval is repeated as many times as set in the setup of the countdown timer. When the last interval is completed, a triple-beep is heard signifying to the user the end of the countdown timer process.

To st art the countdown timer:

1. PRESS the [+] button to start, stop, and restart the timer in the countdown timer sub mode.

2. During an activity, PRESS the [-] button to view the number of intervals remaining. This will be displayed in Field 2.

3. Once the timer has stopped, PRESS the [-] button to reset the timer to zero.

Note: If the user is in other modes or sub modes when the countdown time has been activated, the countdown timer will continue and remain in the background. A flashing “timer” text in Field 3 indicates that the timer is still activated.

2.9 HRM MEMORY

The HRM memory sub mode stores the maximum, minimum, and average heart rates during selected intervals (training or recovery), as well as the time spent in, above and below selected heart rates (target zones). If the heart rate goes beyond the selected zone, an alarm sounds.

To view the HRM Memory , in the HRM mode, PRESS the [Select] button three times to enter this submode. In the HRM Memory mode, there are six display screens.

1. In the first display (main display) (Fig. 8):

• Field 1 displays the year of the start date;

• Field 2 displays the start time; and

• Field 3 displays the start date.

2. In the second display (duration of the event) (Fig. 9):

• Field 1 displays the seconds of training time;

• Field 2 displays the hours and minutes of the training time; and

• Field 3 displays the text “dUr” (dUr = duration of the event).

3. In the third display (duration of the training intervals) (Fig. 10):

• Field 1 displays the seconds of training time;

• Field 2 displays the hours and minutes of the training time; and

• Field 3 displays the text “1dUr” (1dUr = duration of the training intervals).

Note: The third display will be shown only when the countdown timer is used.

4. In the fourth display (heart rate information): (Fig. 11)

• Field 1 displays the maximum heart rate recorded;

• Field 2 displays the average heart recorded; and

• Field 3 displays the minimum heart rate recorded.

5. In the fifth display (time spent above the target heart rate zone) (Fig. 12):

• Field 1 displays the seconds;

• Field 2 displays the hours and minutes; and

• Field 3 displays the text “AbO” (AbO = above target heart rate).

6. In the sixth display (time spent in the target heart rate zone) (Fig. 13):

• Field 1 displays the seconds;

• Field 2 displays the hours and minutes; and

• Field 3 displays the text “In” (In = within the target heart rate).

7. In the seventh display (time spent below the target heart rate zone) (Fig 14):

• Field 1 displays the seconds;

• Field 2 displays the hours and minutes; and

• Field 3 displays the text “bEL” (bEL = below target heart rate).

Note: The HRM memory is for one event only. This feature is automatically activated when starting the stopwatch or countdown timer and will cause the previous event’s information to be erased.

T o view the split times and heart rate readings stored in the memory when using the stopwatch, hold the [Select] button in for 2 seconds when on any of the HRM memory displays.

The display shows the following information (Fig. 15):

• Field 1 displays seconds and tenths of seconds of the stopwatch;

• Field 2 displays your momentaneous heart rate; and

• Field 3 displays hours and minutes of the stopwatch. Press the [+] button to scroll through the stored split times and heart rate readings. Y ou can exit the viewing of stored split times and heart rate readings at any time by pressing the [Mode] button.

CHAPTER 3 TIME MODE

The Suunto Wristop Computer watch function provides the user with:

• an adjustable 24/12 hour clock display;

• a calendar pre-programmed to the year 2089;

• three daily alarms; and

• a dual time operation. T o view and use the Time mode function: Check the Mode Indicator arrow. If the mode arrow is not on TIME, PRESS the [Mode] button until the arrow is directly

below TIME. In the TIME mode (Fig. 16):

• Field 1 displays the day of the week.

• Field 2 displays the current time.

• Field 3 displays the date (month/day if the 12-hour clock has been chosen; day/month if the 24-hour clock has been chosen).

• The Outer Circumference graphically displays time in seconds.

The TIME mode and all sub modes can be adjusted through the setup program of the Wristop Computer.

+ 440 hidden pages