surefire 617f User Guide

Users Manual

Model 617F

Benelli

Tactical Light

Benelli Shotgun

M1 Super 90 12 Gauge

Serial No. M104801 and later

Revision A 7_1_99

Protected by US. Patent 4,856,218

Model 617F Tactical Light

Introduction

The Model 617F Tactical Lights provide a rugged and reliable source of high intensity light that
is integrated into the fore-arm of the shotgun. The lamp is shock isolated. A two button ON/OFF
switch is on the left side of the H17F Housing and a Pressure Switch is on the right side. The
switches are wired in parallel. The ON/OFF switch will turn the light ON or OFF. Press on the
Pressure Switch and the light will come ON, release pressure and light will go OFF. A switch
blocker is provided for users that want to reduce the functional size of the pressure switch.

Kit Contents

! H17F Housing
! L60 Lamp Module
! DL223AC Battery
! Spacer Tube
! Hex Wrench
! Model Z10 Switch Blocker
! Alcohol Wipe
! Users Manual

Installation

1. Put Safety on safe. Open action and make certain no shells remain in chamber or magazine.
Close action and remove Magazine Nut and Barrel.

2. Remove fore-end from Magazine Tube and remove snap ring from front cavity of fore-end
(use eye protection to prevent injury) and remove the three Washers.

3. Install these Washers into the front cavity of the H17F Housing, one Flat Washer then the
Wave Washer and then the second Flat Washer.

4. Take the Spacer Tube from the Kit and install it into the rear of the H17F Housing. Install
it with the open groove up and the wide end of the groove to the back, as shown in the
illustration.

5. Install Housing onto Magazine Tube part way. Lay the Barrel on the Housing and slide
Barrel and Housing toward the receiver until they are seated.

6. Install Magazine Nut and tighten.

7. Adjust Set Screws in H17F Housing to limit rotation of the Housing.

8. Install Battery into Housing with the + terminal facing out.

9. Install Lamp Module into Housing.

10. Apply finger pressure to the Pressure Switch on the right side of the Housing. The
light should come on. Installation is now complete.

11. Test fire the weapon to insure that the boresight has not changed. A shift in pointing may
occur after installing the Tactical Light on the weapon.

Sure-Fire LLC

Model 617F Tactical Light

Switch Blocker Installation

If you want to disable the part of the pressure switch where you rest your hand, (and don’t want
the light to come on) you can cover it with the Model Z10 Switch Blocker. First clean the portion
of the Pressure Switch to be disabled using the Alcohol Wipe from the Kit. Then remove the
paper backing from the underside of the Switch Blocker and press the Switch Blocker in place on
the Pressure Switch.

Battery Replacement

1. Unscrew Lamp Module from Housing and shake out old battery.

2. Install new battery with the + terminal facing out.

3. Reinstall Lamp Module.

Lamp Replacement

1. Unscrew Bezel from Lamp Module. Lift Lamp assembly out of Bezel

2. Install replacement Lamp Assembly in Bezel and reassemble by screwing
onto Lamp Housing until it is fully seated.

Model 617 Tactical Light

Caution

The battery used in the light is very powerful. Be sure that the switch is not touching
anything when the light is stored. If the lamp is turned on while in a case or other container,
the lamp can overheat and damage the light or surrounding materials. Remove the battery or
unscrew the bezel far enough to prevent the lamp from turning on when stored.
If it is necessary to dispose of any batteries, do not do so by fire, mutilation or by
disassembly, as this may cause toxic chemicals to be released.

Repairs & Replacements

To obtain repair or replacement call Customer Service at 800-828-8809 (toll free) or 714-545­9444 and obtain a Return Authorization number (RA). Then pack the unit carefully and return (no
COD’s please) to:
SureFire LLC
Repairs Department, RA# ___
18300 Mt. Baldy Circle
Fountain Valley, CA 92708

Surefire will pay any reasonable shipping costs to return the unit to you.

Warranty
SureFire LLC warrants that its products will be free from defects in materials and
workmanship. SureFire LLC will repair or replace (at its option), without charge, any
product or part which is found to be defective under normal use and service. Such
repair or replacement shall be the purchaser’s sole and exclusive remedy under this
warranty. This warranty does not include normal maintenance and services and does
not apply to any products or parts which have been subject to modification, misuse,
negligence, accident, improper maintenance or repair by anyone other than SureFire.

“Fine Print” Warranty Limitation
There is no other express warranty. SureFire LLC hereby disclaims any and all
implied warranties, including, but not limited to fitness for a particular purpose.
SureFire LLC shall not be liable for incidental, consequential, or special damages
arising out of, or in connection with product use or performance.

Um_H17F_9.701

71-01-437

18300 Mt. Baldy Circle, Fountain Valley, CA 92708 [phone]