suprema XPASS User Manual

Safety Precautions

Product Com

p

onents

Contents

3
5

p

Optional Accessories
Product Description

Product Dimension

6
7
10

Cabl

es and Connectors

Power Connection

LAN Connection

11
14
16

RS485

Connection

Relay Connection
Digital Input Connection

Wiegand Input/Output

18

20
23
25

Output

Installation of Wall-mount Bracket

Installation Reference

26
27
28

S

pec

ificati

on

Electrical Specification

FCC Rules

31
32
33

-2-

Do not install the device in a

Do not place the device next

Safety Precautions

place subject to direct sun

light, humidity, dust or soot.

to heating equipments.

Do not place a magnet
near the product.

When cleaning, do not splash
water on the device but wipe it
out with a smooth cloth or towel.

It may cause a damage or
a failure to the product.

Be careful not to let liquids like
water, drinks or chemicals leak
inside the device.

Clean the device often to
remove dust on it.

The list below is to keep user’s safety and prevent any loss. Please read safety

It may cause a failure

.

-3-

precautions carefully before use

.

Do not drop the device. Do not disassemble, repair or

Safety Precautions

alter the device

.

The warranty does net apply to any
product damage cause by an
arbitrary installation or repair.

Do not let children touch the
device without supervision.

Do not use the device for
any other purpose than
specified.

Do not damage the device. Contact your nearest dealer in

case of a trouble or problem.

The list above is to keep user’s safety and prevent any loss. Please read safety

-4-

precautions carefully before use

.

Product

Components

Basic Components

X

pass

B

racke

t

Extended Ethernet Cable

Wall M

ounting Screws

(2 ea)

Knife Block

s

(2 ea)

Shrinkable Tub

es

Soft

ware

CD

The components shown above may differ depending on the installation environment.

-5-

Optional Accessories

Plastic standSecure I/O Extended Bracket Adaptor

-6-

Product Description

-7-

LED status

-8-

Initialization of network setting

When you install the Xpass or forget the network setting’s value of Xpass in use, can initial the network

’

-

’

settings value (TCP/IP address, RS

485 setting) in the switch of Xpasss back side as follows;

-9-

Product Dimension

(unit : mm)

< Extended Bracket >< Front View > < Bracket >< Side View >

-10-

Cables and Connectors

No Pin Name Full Name Color

1 485 GND 485 GND White (black string)
2 WGD GND Wiegand-GND Black
3 485 - 485 - Yellow (black string)
4 WGD D1 Wiegand-1 White
5 485 + 485 + Blue (white string)
6 WGD D0 Wiegand-0 Green
7 IN 1 Input-1 Brown

8

RLY N

O

Relay Open

G

ray (white string

)

9 IN GND Input-GND Gray
10 RLY COM Relay Com Green (white string)
11 IN 0 Input-0 Purple

12

RLY NC

Relay Close

Orange (black string)

13 TX+ TX+ (LAN) Pink
14 PWR IN+ Power IN+ Red
15 TX- TX- (LAN) Orange

-

-

16

PWR IN

Power IN

Black (white string)

17 RX+ RX+ (LAN) Blue
18 PWR OUT+ Power OUT+ Light Blue
19 RX- RX- (LAN) Yellow
20 PWR OUT- Power OUT- Black (white string)
21 VB1 VB1 Green (black string)
22 VB2 VB2 Brown (white string)
23 VB1 VB1 Green (black string)
24 VB2 VB2 Brown (white string)

-11-

Cables and Connectors

Cable Specification

Cable Pin Name Colo

r

1

Relay

RLY NC Orange (black string)
2 RLY COM Green (white string)
3 RLY NO Gray (white string)
4 WGD D0 Green

Wiegand

5WGD D1White
6 WGD GND Black
7

Switch

IN 0 Purple
8 IN 1 Brown
9IN GNDGray

10

485

485+ Blue (white string)
11 485- Yellow (black string)
12 485 GND White (black string)

Adaptor Connector Pin Name Color

POWER OUT - Black

(

white strin

g)

Power

(g)

POWER OUT + Light Blue
3 POWER IN - Black (white string)
1 POWER IN + Red

-12-

LAN Connector Pin Name Color

1 RX- Yellow

LAN cable

LAN

2 RX+ Blue
3TX-Orange
4 TX+ Pink
5 VB1 Green (black string)

6

VB1

Green (black string)

7 VB2 Brown (white string)
8 VB2 Brown (white string)

Ethernet extension cable

Modular Jack (A) Connector (B) Pin Name Color

14TX+Blue
23TX-Oran

g

e

g

32RX+Black
6 1 RX- Yellow
4 5 VB1 Red
5 6 VB1 Green
7 7 VB2 Brown
8 8 VB2 Gray

-13-

Power Connection

1

Pin Pin Name Color

14 PWR IN+ Red
16 PWR IN- Black (white string)

Recommended power supply

12V ± 10%, at least 1500mA.
Comply with standard IEC/EN 60950-1.
To share the power with other devices, use a power supply with higher current ratings.

-14-

Power Connection

2

Please read below carefully before you install this product. This is essential steps for stable operation. Please

make sure to turn on the power of PSE only after connect all cables related to PoE

① Connect 8port Ethernet connect of
Xpass body to Ethernet expansion
cable in right direction

② Connect RJ45 modular from
Ethernet expansion cable to Ethernet
cable with CAT-5

③

Connect the opposite side of

Ethernet cable to PoE HUB port
④ Connect cable from PC to port from

PoE HUB and connect the opposite
side of cable to Ethernet port of PC

⑤ Connect power of PoE HUB

Please use the distance of LAN cable within 100m in case of PoE power.

Recommended Power Supply

PoE(Power over Ethernet

)

-15-

()

: Use PSE(Power sourcing Equipment) that complies with IEEE802.3af standard only.

LAN Connection

-16-

LAN Connection (Direct connection with PC)

-17-

RS485 Connection for Host Communication

Pin Pin Name Color

1

485 GND

Whi

te

(black

string

)

3 485 - Yellow (black string)
5 485 + Blue (white string)

1

5
3

-18-

RS485 Connection for Secure I/O

Pin Pin Name Color

1

485 GND

White (black string)

3 485 - Yellow (black string)
5 485 + Blue (white string)

Max number of devices

Maximum eight(8) devices (including Master) interworks in an RS485 loop.

-19-

Relay Connection

–

Fail safe lock

PinPin N

ame

Color

10 RLY COM Green (white string)
12 RLY NC Orange (black string)

-20-

Relay Connection

–

Fail secure lock

Pin Pin Name Color

8 RLY NO Gray (white string)

10 RLY COM Green (white string)

-21-

Relay Connection

-

Automatic door

Pin Pin Name Color

8 RLY NO Gray (white string)

10 RLY COM Green (white string)

-22-

Digital Input Connection (Alarm, Emergency S/W)

Pin

Pin Name

Color

7 IN 1 Brown
9IN GND Gray

11 IN 0 Purple

-23-

Digital Input Connection (RTE, Door sensor)

Pin

Pin Name

Color

7 IN 1 Brown
9IN GND Gray

11 IN 0 Purple

Request to

q

Exit

-24-

Wiegand Input

Wiegand Input/Output

Pin Pin Name Color

2 WGD GND Black
4WGD D1 White
6 WGD D0 Green

Wiegand Output

Pin Pin Name Color

2 WGD GND Black
4WGD D1 White
6 WGD D0 Green

-25-

Output

Pin Pin Name Color

10 RLY COM Green (white string)
12 RLY NC Orange (black string)
18 PWR OUT + Light Blue
20 PWR OUT - Black (white string)

Caution : Max. 700mA is supplied using adapter for the external output.

-26-

Be careful to satisfy the power capacity in use

.

Fix wall mount bracket on a wall using
wall mounting screws

Hook Xpass on the wall mount bracket

Installation of Wall

-

mount Bracket

Fix Xpass and wall mounting bracket using

a wall mounting screw.

-27-

Installation Reference 1

-

Stand alone

-28-

Installation Reference 2

–

Standalone (

Secure

)

-29-

Installation Reference 3

–

Network

-30-

Specification

CPU 32 bit Micro-processor

Memory 8MB FLASH + 16MB SDRAM

RF Card

13.56 MHz Mif

are

(XPM)

125 KHz EM Prox (XPE)
125 KHz HID Prox (XPH)

User Capacity 40000 user

Lo

g

Capacit

y

50000 lo

g

gp y

g

Network interfaces TCP/IP, RS485

IP Rate IP 65 class

Sound Multi-tone buzzer

LED

Multi-color LED

RTC Lithium-ion rechargeable batteries

I/O

Relay x 1
Tamper x 1
Switch input x 2

Wiegand x 1

Power 12Vdc, POE

Operating Temperature

-20 ~ 50°C

Size 45 x 130 x 27mm

(

W x H x D )

()

Certificates CE, FCC, KCC, IP65

Caution for RTC Battery

-31-

It may be occurred the risk of

explosion

for improper replacement of battery

.

Please use the specified battery according to proper instruction.

Min. Typ. Max. Notes

Power

Electrical Specification

Voltage (V) 10.8 13.2 Use regulated DC power adaptor only

Current (mA) - 182

Switch Input

V

IH (V) - TBD -

VIL (V) - TBD

Pull-up resistance (Ω) - 4.7k - The input ports are pulled up with 4.7k resistors

TTL/Wie

g

and Output

gp

VOH (V) - 5 -

VOL (V) - 0.8 -

Pull-u

p

resistance (Ω

)

-4.7k -

The outputs ports are open drain type, pulled up with 4.7k

p()

resistors internally

Relay

Switching capacity (A) - -

1

0.3

30V DC
125V AC

Switching power
(resistive)

--

30W

37.5V
A

DC
AC

Switching voltage (V) - -

110
125

DC

A

C

-32-

Changes or modifications not expressly approved by the manufacturer
responsible for compliance could void the user’s authority to operate the

Caution

FCC Rules

equipment

.

This device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interface, and
(2) this device must accept any interface received, including interference that

Warning

may cause undesired operation.

This equipment has been tested and found to comply with the limit of a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed

Information to User

to provide reasonable protection against harmful interference in a residential

installation. This equipment generates, user and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation

;

if this equipment does cause harmful interference to radio or

;qp

television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more the
following measures:

1. Reorient / Relocate the receiving antenna

.

2. Increase the separation between the equipment and receiver.

3. Connect the equipment into an outlet on a circuit difference from that to
which the receiver is connected.

4. Consult the dealer or an experienced radio/TV technician for help

-33-