suprema BioEntry W2, BioEntry P2 Installation Manual
English
Version 1.24
BioEntry W2
INSTALLATION GUIDE
www.supremainc.com
EN 101.00.BEW2 V1.24A
Contents
Safety Instructions .......................................................................................... 3
Introduction ...................................................................................................... 5
Components ................................................................................................................................................... 5
Name and function of each part ............................................................................................................... 6
Cables and connectors......................................................................................................................................................... 7
How to enroll a fingerprint ........................................................................................................................ 8
Selecting a finger for fingerprint input ........................................................................................................................ 8
Fingerprint enroll method ................................................................................................................................................ 8
Installation ........................................................................................................ 9
Fixing the bracket and the product .......................................................................................................... 9
Power supply connection ........................................................................................................................... 11
Network connection .................................................................................................................................... 11
TCP/IP ..................................................................................................................................................................................11
TTL input connection ................................................................................................................................. 12
Relay connection ......................................................................................................................................... 13
Fail Safe Lock ....................................................................................................................................................................13
Fail Secure Lock ................................................................................................................................................................13
Automatic door connection ............................................................................................................................................14
Connecting as a standalone ...................................................................................................................... 15
Connecting to Secure I/O 2 ...................................................................................................................... 16
Wiegand connection ................................................................................................................................... 17
Resetting Network Settings ......................................................................................................................... 17
Restoring the Factory Defaults .................................................................................................................... 17
Product specifications .................................................................................. 18
Dimensions ................................................................................................................................................... 19
FCC Compliance Information ....................................................................... 20
Appendices ..................................................................................................... 21
Disclaimers ................................................................................................................................................... 21
Copyright notice .......................................................................................................................................... 21
Open Source License .................................................................................................................................... 21
GNU General Public License ..............................................................................................................................................21
GNU Lesser General Public License ..................................................................................................................................27
OpenSSL License ................................................................................................................................................................28
Original SSLeay License .....................................................................................................................................................29
Safety Instructions
3
Safety Instructions
Observe the following instructions to use the product safely and prevent any risk of injury or property damage.
Warning
Noncompliance of instructions could lead to serious injury or death.
Installation
Do not install the product in a place with direct sunlight, moisture, dust, or soot.
• A fire or electric shock may occur.
Do not install the product in a place with heat from an electric heater.
• A fire or electric shock may occur due to overheating.
Install the product in a dry place.
• Otherwise, a product damage or electric shock may occur due to moisture.
Install the product in a place with no electromagnetic interference.
• Otherwise, a product damage or electric shock may occur.
The user should not install or repair the product independently.
• A fire, electric shock, or personal injury may occur.
• If the product has been damaged due to independent installation or repair of the product by the user, free A/S service will not be
provided.
Operation
Do not allow liquids such as water, beverages, or chemicals get into the product.
• A fire, electric shock, or product damage may occur.
Caution
Noncompliance of instructions could lead to minor injury or product damage.
Installation
Do not install the power supply cable in a place where people pass by.
• Product damage or physical injury may occur.
Do not install the product near a highly magnetic object such as a magnet, TV, (especially CRT) monitor, or speaker.
• A product failure may occur.
If installing the product outside where the product is completely exposed, it is recommended to install the product together with
the enclosure.
Use a separate power supply for Secure I/O 2, electric lock and BioEntry W2 respectively.
• If connecting and using the power supply to these devices together, the devices may malfunction.
When installing a number of devices, allow a space between the devices for installation.
• Otherwise, one device may affect the RF performance of other devices, resulting in malfunction.
Safety Instructions
4
Operation
Do not drop the product or apply an impact to the product.
• A product failure may occur.
Be careful not to contaminate or damage the fingerprint contact unit with a dirty hand or foreign substances.
• Deterioration in fingerprint authentication performance and a product failure may occur.
When cleaning the product, wipe the product with a soft and dry cloth and no water, benzene or alcohol.
• Otherwise, a product failure may occur.
Electronic Access Control Systems, would be invalidated through the use of any add-on, expansion, memory or other module
manufactured or supplied by the manufacturer or manufacturer’s representative.
Introduction
5
Introduction
Components
Components may vary according to the installation environment.
Note
BioEntry W2
Bracket
PVC anchor
(2 EA)
Fixing screw
(2 EA)
Diode
(1 EA)
120 Ω resistor
(1 EA)
Drilling template
Quick guide
Ferrite core
(1 EA)
Heat shrink tubes
Introduction
6
Name and function of each part
Name Feature
LED lamp Indicates the operational status of the product with the color of the LED lamp.
RF card authentication
unit
Reads RF cards for entering and exiting.
Fingerprint
authentication unit
Reads fingerprints placed on it for entering and exiting.
Cable
• TTL input cable
• Wiegand input or output cable
• Power cable
• RS485 cable
• Ethernet connector
•
Relay output cable
LED lamp for Network
Shows the status of the network connection.
Reset button
•
Resets the network configuration. For details, refer to the
Resetting Network Setting
.
• Deletes all data and certificate on the device and reset the settings. For details, refer to the Restoring the
Factory Defaults.
Fingerprint
authentication unit
LED lamp
RF card
authentication unit
LED status indicator for Net
work
Network reset button
Cable
Introduction
7
Cables and connectors
• There are several conductors of size of AWG 26 and they shall be covered by a common jacket or the equivalent when field wiring; And the lead
shall not be spliced to a conductor larger than 18 AWG (0.82 mm
2
).
Note
Pin
Name
Color
1
RLY NO
Gray (White stripe)
2
RLY COM
Green (White stripe)
3
RLY NC
Orange (White stripe)
4 VB2
Blue
Brown
5 VB1
Red
Green
6
WG D0
Green
7
WG D1
White
8
WG GND
Black 9 TTL IN 1
Brown
10
TTL IN 0
Purple
11
PWR +VDC
Red
12
Not Connected
Pink
13
PWR GND
Black (White stripe)
14
485 TRXN
Yellow (Black stripe)
15
485 TRXP
Blue (White stripe)
16
485 GND
White (Black stripe)
17
ENET TXP
White
18
ENET T XN
Orange
19
ENET RXP
Black
20
ENET RXN
Yellow
Introduction
8
How to enroll a fingerprint
In order to improve the fingerprint authentication rate, register the fingerprint correctly. BioEntry W2 can recognize a fingerprint even if the
angle and position of a user's fingerprint input change. If you register the fingerprint with attention to the following matters, the
authentication rate can be improved.
Selecting a finger for fingerprint input
•
In preparation for the case that the fingerprint of a specific finger cannot be used, for example if
the user is lifting a load with one hand or a finger gets hurt, up to 10 fingerprints for each user can
be registered.
• In the case of a user whose fingerprint cannot be recognized well, the authentication rate can be
improved by enrolling the same finger twice repeatedly.
• If a finger has a cut or the fingerprint is blurry, select another finger for the fingerprint.
• It is recommended to use the index finger or the middle finger when scanning the fingerprint. The
authentication rate can be reduced if it is difficult to place another finger at the center of
fingerprint sensor accurately.
Fingerprint enroll method
1
Place the finger with the fingerprint to be registered on the fingerprint authentication unit and press the finger gently for better
authentication.
2
After a beep sounds, scan the
fingerprint of the registered finger again (scan the fingerprint of a finger to be registered twice).
Cautions for enrolling a fingerprint
When a fingerprint is recognized, it is compared with the initially registered fingerprint, so the initial fingerprint enroll is the most important. Pay
attention to the following matters when enrolling the fingerprint.
• Place the finger deep enough to contact with the sensor completely.
• Place the center of the fingerprint in the center of the sensor.
• If a finger has a cut or the fingerprint is blurry, select another finger for the fingerprint.
• Scan the fingerprint correctly without moving according to the instructio n on the screen.
• If you make the finger upright so that the contact area with the sensor has decreased or the angle of finger has warped, fingerprint authentication
may not be performed.
When the fingerprint recognition fails
BioEntry W2 can recognize a fingerprint regardless of a change of season or finger condition. However, the authentication rate may vary according to
the external environment or fingerprint input method.
If the fingerprint authentication cannot be done smoothly, it is recommended to take the following measures.
• If the finger is smeared with water or sweat, dry off the finger and then scan the finger.
• If the finger is too dry, blow your breath on the fingertips and then scan the finger.
• If the finger has a cut, register the fingerprint of another finger.
• The initially registered fingerprint often may have not been scanned correctly, so register the fingerprint again according to ‘Cautions for enrolling
a fingerprint’.
Note
Installation
9
Installation
Fixing the bracket and the product
1 Determine the correct position to install the bracket using the provided drilling template. Fix the bracket firmly using fixing screws
through the bracket to the position where BioEntry W2 will be installed.
• If installing BioEntry W2 on a concrete wall, drill holes, insert PVC anchors, and fix them with fixing screws.
• To avoid RF interference, a minimum separation distance must be maintained.
Wall thickness Distance
100 mm
270 mm
120 mm
250 mm
150 mm
170 mm
Wall
300 mm
Wall
Distance
Wall thickness
Note
Loading...