Sunrise Medical BREEZY SERIES, 600 SERIES, 500 SERIES, BREEZY 600 SERIES, BREEZY 500 SERIES User Instruction Manual & Warranty

User

Instruction

Manual &

Warranty

Breezy Series Wheelchair

500 Series
600 Series

930300 Rev.C

3

930300 Rev.C

SUNRISE LISTENS

Thank you for choosing a Breezy wheelchair. We want to hear your questions or
comments about this manual, the safety and reliability of your chair, and the ser­vice you receive from your supplier. Please feel free to write or call us at the
address and telephone number below:

SUNRISE HOME HEALTHCARE GROUP
MOBILITY PRODUCTS DIVISION

Customer Service Department
7477 East Dry Creek Parkway
Longmont, CO 80503
[phone]

Be sure to return your warranty card,and let us know if you change your address.
This will allow us to keep you up to date with information about safety, new prod­ucts and options to increase your use and enjoyment of this wheelchair. If you lose
your warranty card, call or write and we will gladly send you a new one.

FOR ANSWERS TO YOUR QUESTIONS

Your authorized supplier knows your wheelchair best, and can answer most of
your questions about chair safety, use and maintenance. For future reference,
fill in the following:

Supplier:______________________________________________________________________________

Address: ______________________________________________________________________________

______________________________________________________________________________________

Telephone: ____________________________________________________________________________

Serial #: _____________________________________ Date/Purchased: ________________________

1. INTRODUCTION

4 5

930300 Rev.C 930300 Rev.C

II. TABLE OF CONTENTS

1I. TABLE OF CONTENTS

1. INTRODUCTION .............................................................................. 3

a. Sunrise Listens ...................................................................................... 3

11. TABLE OF CONTENTS .................................................................. 4

III. YOUR CHAIR AND ITS PARTS ................................................ 6

IV. NOTICE - READ BEFORE USE .................................................. 12

V. GENERAL WARNINGS.................................................................... 13

a. Weight Limit ........................................................................................ 13

b. Weight Training .................................................................................... 13

c. Getting to Know Your Chair ............................................................ 13

d. To Reduce The Risk of an Accident ................................................ 13

e. Safety Checklist .................................................................................. 14

f. Changes & Adjustments .................................................................... 14

g. Environmental Conditions ................................................................ 14

h. Terrain .................................................................................................... 15

i. Street Use ............................................................................................ 15

j. Motor Vehicle Safety .......................................................................... 15

k. When You Need Help ........................................................................ 16

VI. WARNINGS: FALLS & TIP-OVERS .......................................... 17

a. Center of Balance .............................................................................. 17

b. Dressing or Changing Clothes ........................................................ 17

c. Wheelies .............................................................................................. 18

d. Obstacles .............................................................................................. 18

e. Reaching or Leaning .......................................................................... 19

f. Moving Backward ................................................................................ 20

g. Ramps, Slopes & Side Hills ................................................................ 20

h. Transfers ................................................................................................ 21

i. Curbs & Steps ...................................................................................... 22

j. Stairs ...................................................................................................... 22

k. Escalators .............................................................................................. 22

VII. WARNINGS: FOR SAFE USE ...................................................... 23

a. Learning to do a “Wheelie” ............................................................ 23

b. Descending a Curb or Single Step .................................................. 23

c. Climbing a Curb or Single Step ...................................................... 24

d. Climbing Stairs .................................................................................... 24

e. Descending Stairs ................................................................................ 24

f. Maintenance .......................................................................................... 25

VIII. WARNINGS: COMPONENTS & OPTIONS ........................ 26

a. Anti-Tip Tubes ...................................................................................... 26

b. Armrests .............................................................................................. 26

c. Cushion & Sling Seats ........................................................................ 26

d. Fasteners .............................................................................................. 27

e. Footrests ................................................................................................ 27

f. Pneumatic Tires .................................................................................. 27

g. Positioning Belts .................................................................................. 28

h. Power Drive ........................................................................................ 28

i. Push Handles ........................................................................................ 28

j. Quick-Release Axles .......................................................................... 29

k. Rear Axles ............................................................................................ 29

l. Rear Wheel Locks .............................................................................. 29

m.Modified Seat Systems ...................................................................... 30

n. Upholstery Fabric .............................................................................. 30

IX. CHAIR BASICS .................................................................................. 31

a. To Mount & Remove Rear Wheels ................................................ 31

a. To Fold & Unfold Chair .................................................................... 32

X. SET-UP AND ADJUSTMENTS .................................................... 33

a. Set-up .................................................................................................... 33

b. Tools ...................................................................................................... 33

c. To Find and Correct a Problem........................................................ 34

d. Anti-Tip Tubes ...................................................................................... 34

e. Standard & Low Front Seat Heights .............................................. 36

f. Caster Forks ........................................................................................ 37

g. Axle-Plate Adjustable ........................................................................ 37

h. Toe-in and Toe-out .............................................................................. 37

i. Rear Wheels - Threaded or Fixed Offset Axles .......................... 38

j. Rear Wheel Locks .............................................................................. 38

k. Flip-Back Armrests .............................................................................. 38

l. Flip-Back Height Adjustable Armrests ............................................ 39

m.Swing-Away Hangers & Footrests ................................................ 30

n. Articulating Legrest & Elevating Legrest ...................................... 41

o. Caster Plates ...................................................................................... 41

p. Caster Mounting ................................................................................ 42

q. Backrest .............................................................................................. 42

XI. TROUBLESHOOTING .................................................................... 44

X11. MAINTENANCE ................................................................................ 45

XIII. SUNRISE LIMITED WARRANTY .............................................. 47

6 7

930300 Rev.C 930300 Rev.C

III. YOUR CHAIR AND ITS PARTS

1. Flip-back armrest

2. Padded seat sling

3. Swing-away footrest

4. Crossbrace

5. Flip-up composite footplate

6. Caster housing dust cover

7. Caster housing

8. Caster fork

9. 8” (203 mm) caster wheel with
molded tire

10. Push handle and adjustable back­rest tube

11. Backrest

12. 24” (540 mm) molded tire with
6-spoke mag wheel

13. Handrim

14. Side frame

15. Threaded axle

16. Swing-away release latch

17. Anti-tip tube (optional)

III. YOUR CHAIR AND ITS PARTS

BREEZY 500

Weight

33-35 lbs. (15kg-15.9 kg)

Adjustments

1” (25 mm)Vertical Caster
Adjustment with
2 Hole Fork
Footrest Extension Adjustment

Frame Dimensions

Seat Width: 16”,18” (406 mm,457 mm)
Seat Depth: 16” (406 mm)

Colors

Silver Texture

Backrest

17”-19” (432 mm-483 mm) Adjustable

Seat Sling

Standard: Padded Seat Sling
Optional: Nonpadded

Armrests

Flip-Back w/Desk-Length Pad, Flip­Back w/Full-Length Pad, Flip-Back
Height Adjustable w/Desk-Length
Pad, Flip-Back Height-Adjustable
with Full-Length Pad

Hangers

Standard: 60

o

Swing-Away

Optional:Articulating or Elevating
Legrests

Footplates

Composite

Axle Assembly

Threaded Rear Axles

Anti-Tip Tubes

Rear Anti-Tip Tubes

Casters

8” (203 mm) Caster with Molded Tire

Wheel Locks

High-Push, High-Pull
Wheel Lock, Options: 6” (152 mm)

Extension Handles with Bungie

Rear Wheels

24" (540 mm) Molded Tire with
6-Spoke Mag Wheel

All features may not be available with
some chair setups or in conjunction
with another chair feature. Please con­sult your authorized supplier for more
information.

1

2

3

4

5

6

7

8

9

10

11

14

12

16

17

13

15

8 9

930300 Rev.C 930300 Rev.C

III. YOUR CHAIR AND ITS PARTS

1. Flip-back armrest

2. Padded seat sling

3. Swing-away footrest

4. Crossbrace

5. Flip-up composite footplate

6. Caster housing dust cover

7. Caster housing

8. Caster fork

9. 8” (203 mm) polyurethane
caster tire

10. Push handle backrest tube

11. Backrest

12. 24” (540 mm) low-profile
polyurethane tire

13. 6-spoke mag wheel

14. Handrim

15. Step tube (not shown)

16. Threaded axle

17. Swing-away release latch

18. Anti-tip tube (optional)

BREEZY 510

III. YOUR CHAIR AND ITS PARTS

Weight

30 lbs. (13.6 kg)

Adjustments

1” (25 mm) Vertical Caster
Adjustment with
2 Hole Fork
Footrest Extension Adjustment

Colors

Blue, Silver Texture, Chrome

Frame Dimensions

Seat Width: Std. - 14”, 16”,18”
(356 mm, 406 mm,457 mm)

Opt - 20” (508 mm)
Seat Depth:

Std - 16” (406 mm)
Opt - 18” (457 mm)

Backrest

17”-19” (432 mm-483 mm) adjustable

Hangers

Std - 60

o

Swing-Away

Opt - 70

o

Swing-Away Articulating

or Elevating Legrests

Footplates

Std - Composite with heel loops
Opt - Extension Tubes: Short,

Medium, Long

Casters

Std - 8” polyurethane
Opt - 5” low-profile polyurethane
with composite caster rims

Armrests

Flip-Back w/Desk-Length Pad, Flip­Back w/Full-Length Pad, Flip-Back
Height Adjustable w/Desk-Length
Pad, Flip-Back Height-Adjustable
with Full-Length Pad

Axles

Std - threaded
Opt - threaded offset, quick-release

Anti-Tip Tubes

Opt - Rear Anti-Tip Tubes

Rear Wheels

Type: Std -mag,Opt
Sizes: Std - 24”, 22”, Opt - 20”
Tires: Std - low profile polyurethane
Opt - pneumatic, full-profile

polyurethane, airless inserts

Handrims

Std - composite, aluminum
Opt - plastic-coated

Projections Handrims

Opt - 8,12 vertical or oblique

Wheel Locks

Std - High push-to-lock, High
pull-to-lock,

Opt - 6” (152 mm) extension handles
with bungee, grade aids

All features may not be available with
some chair setups or in conjunction
with another chair feature. Please
consult your authorized supplier for
more information.

1

2

3

4

5

6
7

8

9

10

11

12

13

16

17

14

18

10 11

930300 Rev.C 930300 Rev.C

III. YOUR CHAIR AND ITS PARTS

III. YOUR CHAIR AND ITS PARTS

1. Flip-back armrest

2. Padded seat sling

3. Swing-away footrest

4. Crossbrace

5. Flip-up composite footplate

6. Caster housing dust cover

7. Caster housing

8. Caster fork

9. Caster wheel

10. 8” (203 mm) polyurethane
caster tire

11. Push handle backrest tube

12. Backrest

13. 24” (540 mm) low-profile
polyurethane tire

14. 6-spoke mag wheel

15. Composite handrim

16. Step-tube
(not shown)

17. Threaded axle

18. Swing-away release latch

19. Anti-tip tube (optional)

BREEZY 600

Weight

28 lbs. (12.7 kg)

Adjustments

1” (25 mm) Vertical Axle- Adjustment,
2-Hole Fork Footrest Extension
Adjustment,Adjustable Caster
Housing, Backrest Adjustment

Colors

Blue, Silver Texture, Forest Green

Frame Dimensions

Seat Width - Std
14”, 15”,16”, 17”, 18”, 19”, 20”
(356 mm, 381 mm, 406 mm, 432 mm,

457 mm, 483 mm, 508 mm)
Seat Depth
14”, 15”,16”, 17”, 18”

(356 mm, 381 mm, 406 mm, 432 mm,
457 mm)

Backrest

16” - 19” (406 mm - 483 mm)

Hangers

60

o

,70o,90

o

ELR,ALR

Footplates

Std - composite with heel loop
Opt -

90

o

Flip up

Ext. tubes - short, med.,long

Casters

5”, 6”, 8” (127 mm, 157 mm, 203 mm)
Polyurethane & pneumatic
1 1/2” & 3/4” (38 mm & 19 mm)

caster fork stem

Axles/Axle Plate

Std - Offset Fixed
Opt - Quick-Release

Anti-Tip Tubes

Opt - Rear Anti-Tip Tubes

Rear Wheels

Type - mag
Sizes - 20”, 22”, 24”

Tires - Polyurethane

Pneumatic

Handrims

Std - composite, aluminum
Opt - plastic-coated

Projections Handrims

Opt - 8,12 vertical or oblique

Wheel Locks

Std - High push-to-lock, High pull­to-lock,

Opt - 6” (152 mm) extension
handles, grade aids

All features may not be available with
some chair setups or in conjunction
with another chair feature. Please
consult your authorized supplier for
more information.

1

2

3

4

5

6

7

8

9

11

12

13

10

14
15

17

18

19

12

13

930300 Rev.C

930300 Rev.C

IV. NOTICE—READ BEFORE USE

V. GENERAL WARNINGS

A. WEIGHT LIMIT

NEVER exceed the weight limit of 250 pounds (113.6 kilograms), for combined
weight of rider and items carried. If you do exceed the limit, damage to your
chair, a fall, tip-over or loss of control may occur and cause severe injury to the
rider or others.

B. WEIGHT TRAINING

NEVER use this chair for weight training if total weight (rider plus equip­ment) exceeds 250 pounds (113.6 kg). If you do exceed the limit, damage to
your chair, a fall, tip-over or loss of control may occur and cause severe
injury to the rider or others.

C. GETTING TO KNOW YOUR CHAIR

Every wheelchair is different.Take the time to learn the feel of this chair
before you begin riding. Start slowly, with easy, smooth strokes. If you are used
to a different chair, you may use too much force and tip over. If you use too
much force, damage to your chair, a fall, tip-over or loss of control may occur
and cause severe injury to the rider or others.

D. TO REDUCE THE RISK OF AN ACCIDENT

1. BEFORE riding, you should be trained in the safe use of this chair by your
health care advisor.

2. Practice bending, reaching and transfers until you know the limit of your
ability. Have someone help you until you know what can cause a fall or
tip-over and how to avoid doing so.

3. Be aware that you must develop your own methods for safe use best
suited to your level of function and ability.

4. NEVER tr y a new maneuver on your own until you are sure you can
do it safely.

5. Get to know the areas where you plan to use your chair.Look for
hazards and learn how to avoid them.

6. Use anti-tip tubes unless you are a skilled rider of this chair and are sure
you are not at risk to tip over.

If you fail to heed these warnings damage to your chair, a fall,tip-over or loss of
control may occur and cause severe injury to the rider or others.

▲

!

A. CHOOSE THE RIGHT CHAIR & SAFETY OPTIONS

Sunrise provides a choice of many wheelchair styles to meet the needs of the
wheelchair rider. However, final selection of the type of wheelchair, options and
adjustments rests solely with you and your health care advisor. Choosing the
best chair and set-up for your safety depends on such things as:

1. Your disability, strength,balance and coordination.

2. The types of hazards you must overcome in daily use (where you live and
work, and other places you are likely to use your chair).

3. The need for options for your safety and comfort (such as anti-tip tubes,
positioning belts, or special seating systems).

B. REVIEW THIS MANUAL OFTEN

Before using this chair you, and each person who may assist you, should
read this entire manual and make sure to follow all instructions. Review the
warnings often, until they are second nature to you.

C. WARNINGS

The word “WARNING” refers to a hazard or unsafe practice that may
cause severe injury or death to you or to other persons.The “Warnings”
are in four main sections, as follows:

1. V — GENERAL WARNINGS

Here you will find a safety checklist and a summary of risks you need to be
aware of before you ride this chair.

2. VI — WARNINGS — FALLS & TIP-OVERS

Here you will learn how to avoid a fall or tip-over while you perform daily
activities in your chair.

3. VII — WARNINGS — FOR SAFE USE

HERE YOU WILL LEARN ABOUT PRACTICES FOR THE SAFE USE OF
YOUR CHAIR

4. VIII — WARNINGS — COMPONENTS & OPTIONS

Here you will learn about the components of your chair and options you can
select for safety. Consult your authorized supplier and your health care advisor
to help you choose the best set-up and options for safe use.

Note: Where they apply, you will also find “Warnings” in other sections of this manual.

Heed all warnings in this section. If you fail to do so a fall, tip-over or loss of control may

occur and cause severe injury to the rider or others.

V. GENERAL WARNINGS

H. TERRAIN

1. Your chair is designed for use on firm, even surfaces such as concrete,
asphalt and indoor floors and carpeting.

2. Do not operate your chair in sand, loose soil or over rough terrain.
This may damage wheels or axles, or loosen fasteners of your chair.

If you fail to heed these warnings damage to your chair, a fall,tip-over or loss of
control may occur and cause severe injury to the rider or others.

I. STREET USE

In most states, wheelchairs are not legal for use on public roads. Be alert to the
danger of motor vehicles on roads or in parking lots.

1. At night, or when lighting is poor, use reflective tape on your chair
and clothing.

2. Due to your low position, it may be hard for drivers to see you. Make eye
contact with drivers before you go forward. When in doubt, yield until you are
sure it is safe.

If you fail to heed these warnings damage to your chair, a fall,tip-over or loss of
control may occur and cause severe injury to the rider or others.

J. MOTOR VEHICLE SAFETY

Breezy wheelchairs do not meet federal standards for motor vehicle seating.

1. NEVER let anyone sit in this chair while in a moving vehicle.

a. ALWAYS move the rider to an approved vehicle seat.
b. ALWAYS secure the rider with proper motor vehicle restraints.

2. In an accident or sudden stop the rider may be thrown from the chair.

Wheelchair seat belts will not prevent this, and further injury may result
from the belts or straps.

3. NEVER transport this chair in the front seat of a vehicle. It may shift and

interfere with the driver.

4. ALWAYS secure this chair so that it cannot roll or shift.

5. Do not use any chair that has been involved in a motor vehicle accident.

If you fail to heed these warnings damage to your chair, a fall,tip-over or loss of
control may occur and cause severe injury to the rider or others.

▲

!

14

15

930300 Rev.C

930300 Rev.C

E. SAFETY CHECKLIST

Before Each Use Of Your Chair:

1. Make sure the chair rolls easily and that all parts work smoothly. Check
for noise, vibration,or a change in ease of use. (They may indicate low tire
pressure, loose fasteners, or damage to your chair).

2. Repair any problem.Your authorized supplier can help you find and cor­rect the problem.

3. Check to see that both quick-release rear axles are locked.When locked,
the axle button will “pop out” fully. If not locked, the wheel may come off
and cause you to fall.

4. If your chair has anti-tip tubes, lock them in place.

Note: See “Anti-Tip Tubes” (Section VIII) for times you should not use them.

If you fail to heed these warnings damage to your chair, a fall,tip-over or loss
of control may occur and cause severe injury to the rider or others.

F. CHANGES & ADJUSTMENTS

1. If you modify or adjust this chair, it may increase the risk of a tip-over UNLESS
you make other changes as well.

2. Consult your authorized supplier BEFORE you modify or adjust your chair.

3. We recommend that you use anti-tip tubes until you adapt to the change, and
are sure you are not at risk to tip over.

4. Unauthorized modifications or use of parts not supplied or approved by Sunrise
may change the chair structure.This will void the warranty and may cause a
safety hazard.

If you fail to heed these warnings damage to your chair, a fall,tip-over or loss of
control may occur and cause severe injury to the rider or others.

G. ENVIRONMENTAL CONDITIONS

1. Use extra care if you must ride your chair on a wet or slick surface. If you are
in doubt, ask for help.

2. Contact with water or excess moisture may cause your chair to rust or
corrode.This could cause your chair to fail.

a. Do not use your chair in a shower, pool or other body of water. The chair

tubing and parts are not water-tight and may rust or corrode from the inside.

b. Avoid excess moisture (for example, do not leave your chair in a damp

bathroom while taking a shower).

c. Dry your chair as soon as you can if it gets wet, or if you use water to

clean it.
If you fail to heed these warnings damage to your chair, a fall,tip-over or loss of
control may occur and cause severe injury to the rider or others.

V. GENERAL WARNINGS

▲

!

16

17

930300 Rev.C

930300 Rev.C

V. GENERAL WARNINGS

K. WHEN YOU NEED HELP

For The Rider:

Make sure that each person who helps you reads and follows all warnings and
instructions that apply.

For Attendants:

1. Work with the rider’s doctor, nurse or therapist to learn safe methods
best suited to your abilities and those of the rider.

2. Tell the rider what you plan to do, and explain what you expect the rider
to do.This will put the rider at ease and reduce the risk of an accident.

3. Make sure the chair has push handles.They provide secure points for
you to hold the rear of the chair to prevent a fall or tip-over. Check to
make sure push handle grips will not rotate or slip off.

4. To prevent injury to your back, use good posture and proper body
mechanics.When you lift or support the rider or tilt the chair, bend your
knees slightly and keep your back as upright and straight as you can.

5. Remind the rider to lean back when you tilt the chair backward.

6. When you descend a curb or single step, slowly lower the chair in one
easy movement. Do not let the chair drop the last few inches to the
ground.This may damage the chair or injure the rider.

7. To avoid tripping, unlock and rotate anti-tip tubes up, out of the way.
ALWAYS lock the rear wheels and lock anti-tip tubes in place if you
must leave the rider alone, even for a moment.This will reduce the risk
of a tip over or loss of control of the chair.

If you fail to heed these warnings damage to your chair, a fall,tip-over or loss
of control may occur and cause severe injury to the rider or others.

▲

!

VI. WARNINGS: FALLS & TIP-OVERS

A. CENTER OF BALANCE

The point where this chair will tip forward, back, or to the side depends on its
center of balance and stability. How your chair is set up, the options you select
and the changes you make may affect the risk of a fall or tip-over.

1. The Most Important Adjustments Are:
a. The position of the rear wheels.The more you move the rear wheels

forward, the more likely your chair will tip over backward.

2. The Center Of Balance Is Also Affected By:

a. A change in the set-up of your chair, including:

• The distance between the rear wheels.

• The amount of rear wheel camber.

• The seat height and seat angle.

• Backrest angle.
b. A change in your body position, posture or weight distribution.
c. Riding your chair on a ramp or slope.
d. The use of a back pack or other options, and the amount of added weight.

3. To Reduce The Risk Of An Accident:
a. Consult your doctor, nurse or therapist to find out what axle and

caster position is best for you.

b. Consult your authorized supplier BEFORE you modify or adjust this

chair. Be aware that you may need to make other changes to correct
the center of balance.

c. Have someone help you until you know the balance points of your

chair and how to avoid a tip-over.

d. Use anti-tip tubes.

If you fail to heed these warnings damage to your chair, a fall,tip-over or loss
of control may occur and cause severe injury to the rider or others.

B. DRESSING OR CHANGING CLOTHES

Your weight may shift if you dress or change clothes while seated in this chair.
To reduce the risk of a fall or tip-over:

1. Rotate the front casters until they are as far forward as possible.

This makes the chair more stable.

2. Lock anti-tip tubes in place. (If your chair does not have anti-tip tubes,

back it up against a wall and lock both rear wheels).
If you fail to heed these warnings damage to your chair, a fall,tip-over or loss of
control may occur and cause severe injury to the rider or others.

▲

!

18

19

930300 Rev.C

930300 Rev.C

VI. WARNINGS: FALLS & TIP-OVERS

▲

!

C. WHEELIES

Doing a “wheelie” means balancing on the rear wheels of your chair while
the front casters are in the air. It is dangerous to do a "wheelie" as a fall or
tip-over may occur. However, if you do it safely,a “wheelie” can help you
overcome curbs and obstacles.

1. Consult your doctor, nurse or therapist to find out if you are a good
candidate to learn to do a “wheelie.”

2. Do not attempt a “wheelie” UNLESS you are a skilled rider of this chair,
or you have help.

Note: See p. 23 for steps to learn to do a “wheelie.”

If you fail to heed these warnings damage to your chair, a fall,tip-over or loss of
control may occur and cause severe injury to the rider or others.

D. OBSTACLES

Obstacles and road hazards (such as potholes and broken pavement) can
damage your chair and may cause a fall, tip-over or loss of control.
To avoid these risks:

1. Keep a lookout for danger – scan the area well ahead of your chair
as you ride.

2. Make sure the floor areas where you live and work are level and
free of obstacles.

3. Remove or cover threshold strips between rooms.

4. Install a ramp at entry or exit doors. Make sure there is not a drop off at
the bottom of the ramp.

5. To Help Correct Your Center Of Balance:
a. Lean your upper body FORWARD slightly as you go UP over an obstacle.
b. Press your upper body BACKWARD as you go DOWN from a higher

to a lower level.

6. If your chair has anti-tip tubes, lock them in place before you go UP
over an obstacle.

7. Keep both of your hands on the handrims as you go over an obstacle.

8. Never push or pull on an object (such as furniture or a doorjamb) to
propel your chair.

If you fail to heed these warnings damage to your chair, a fall,tip-over or loss of
control may occur and cause severe injury to the rider or others.

VI. WARNINGS: FALLS & TIP-OVERS

▲

!

E. REACHING OR LEANING

If you reach or lean it will affect the center of balance of your chair.This may
cause you to fall or tip over.When in doubt, ask for help or use a device to
extend your reach.

1. NEVER reach or lean if you must shift your weight sideways or rise up
off the seat.

2. NEVER reach or lean if you must move forward in your seat to do so.
Always keep your buttocks in contact with the backrest.

3. NEVER reach with both hands (you may not be able to catch yourself
to prevent a fall if the chair tips).

4. NEVER reach or lean to the rear unless your chair has anti-tip tubes
locked in place.

5. DO NOT reach or lean over the top of the seat back.This may damage
one or both backrest tubes and cause you to fall.

6. If You Must Reach Or Lean:
a. Do not lock the rear wheels.This creates a tip point and makes a fall

or tip-over more likely.

b. Do not put pressure on the footrests.

Note: Leaning forward puts pressure on the footrests and may cause the chair to tip if

you lean too far.

c. Move your chair as close as you can to the object you wish to reach.
d. Do not try to pick up an object from the floor by reaching down

between your knees.You are less likely to tip if you reach to the side
of your chair.

e. Rotate the front casters until they are as far forward as possible.This

makes the chair more stable.

Note: To do this: Move your chair past the object you want to reach, then back up

alongside it. Backing up will rotate the casters forward.

f. Firmly grasp a rear wheel or an armrest with one hand.This will help

to prevent a fall if the chair tips.
If you fail to heed these warnings damage to your chair, a fall,tip-over or loss of control
may occur and cause severe injury to the rider or others.

20

21

930300 Rev.C

930300 Rev.C

VI. WARNINGS: FALLS & TIP-OVERS

F. MOVING BACKWARD

Use extra care when you move your chair backward.Your chair is most stable
when you propel yourself forward.You may lose control or tip over if one of
the rear wheels hits an object and stops rolling.

1. PROPEL YOUR CHAIR SLOWLY AND SMOOTHLY.

2. IF YOUR CHAIR HAS ANTI-TIP TUBES, MAKE SURE TO LOCK
THEM IN PLACE.

3. Stop often and check to be sure your path is clear.

If you fail to heed these warnings damage to your chair, a fall,tip-over or loss of
control may occur and cause severe injury to the rider or others.

G. RAMPS, SLOPES & SIDE HILLS

Riding on a slope, which includes a ramp or side hill, will change the center of
balance of your chair.Your chair is less stable when it is at an angle.Anti-tip tubes
may not prevent a fall or tip-over.

1. Do not use your chair on a slope steeper than 10%. (A 10% slope means: one
foot in elevation for every ten feet of slope length.)

2. Always go as straight up and as straight down as you can. (Do not “cut the
corner” on a slope or ramp.)

3. Do not turn or change direction on a slope.

4. Always stay in the CENTER of the ramp. Make sure ramp is wide enough that
you are not at risk that a wheel may fall over the edge.

5. Do not stop on a steep slope. If you stop, you may lose control of your chair.

6. NEVER use rear wheel locks to try to slow or stop your chair.This is likely
to cause your chair to veer out of control.

7. Beware Of:
a. Wet or slippery surfaces.
b. A change in grade on a slope (or a lip, bump or depression).These may

cause a fall or tip-over.

c. A drop-off at the bottom of a slope. A drop-off of as small as 3/4 inch can

stop a front caster and cause the chair to tip forward.

8. To Reduce The Risk Of A Fall Or Tip-Over:
a. Lean or press your body UPHILL.This will help adjust for the change in the

center of balance caused by the slope or side hill.

b. Keep pressure on the handrims to control your speed on a down slope.

If you go too fast you may lose control.

c. Ask for help any time you are in doubt.

▲

!

VI. WARNINGS: FALLS & TIP-OVERS

9. Ramps At Home & Work - For your safety, ramps at home and work must
meet all legal requirements for your area.We recommend:
a. Width.At least four feet wide.
b. Guardrails.To reduce the risk of a fall, sides of ramp must have guardrails

(or raised borders at least three inches high).
c. Slope. Not more than a 10% grade.
d. Surface. Flat and even, with a thin carpet or other non-skid material.

(Make sure there is no lip, bump or depression.)
e. Bracing. Ramp must be STURDY.You may need bracing so ramp does not

“bow” when you ride on it.
f. Avoid A Drop Off.You may need a section at the top or bottom to smooth

out the transition.

If you fail to heed these warnings damage to your chair, a fall,tip-over or loss of
control may occur and cause severe injury to the rider or others.

H. TRANSFER

It is dangerous to transfer on your own. It requires good balance and agility.
Be aware that there is a point during every transfer when the wheelchair seat
is not below you.To Avoid A Fall:

1. Work with your health care advisor to learn safe methods.

a. Learn how to position your body and how to support yourself during

a transfer.

b. Have someone help you until you know how to do a safe transfer on

your own.

2. Lock the rear wheels before you transfer.This keeps the rear wheels

from rolling.

Note: This will NOT keep your chair from sliding away from you or tipping.

3. Make sure to keep pneumatic tires properly inflated. Low tire pressure

may allow the rear wheel locks to slip.

4. Move your chair as close as you can to the seat you are transferring to.

If possible, use a transfer board.

5. Rotate the front casters until they are as far forward as possible.

6. If you can, remove or swing footrests out of the way.

a. Make sure your feet do not catch in the space between the footrests.
b. Avoid putting weight on the footrests as this may cause the chair to tip.

7. Make sure armrests are out of the way and do not interfere.

8. Transfer as far back onto the seat surface as you can.This will reduce the

risk that the chair will tip or move away from you.
If you fail to heed these warnings damage to your chair, a fall,tip-over or loss of
control may occur and cause severe injury to the rider or others.

▲

!

22

23

930300 Rev.C

930300 Rev.C

VI. WARNINGS: FALLS & TIP-OVERS

I. CURBS & STEPS

1. Each person who helps you should read and follow the warnings
“For Safe Use” (Section VII).

2. Do not try to climb or descend a curb or step alone UNLESS you
are a skilled rider of this chair and:

a. You can safely do a “wheelie”; and
b. You are sure you have the strength and balance to do so.

3. Unlock and rotate anti-tip tubes up, out of the way, so they do
not interfere.

4. Do not try to climb a high curb or step (more than 4 inches high)
UNLESS you have help. Doing so may cause your chair to exceed its
balance point and tip over.

5. Go straight up and straight down a curb or step.If you climb or descend
at an angle, a fall or tip-over is likely.

6. Be aware that the impact of dropping down from a curb or step can
damage your chair or loosen fasteners.

If you fail to heed these warnings damage to your chair, a fall,tip-over or loss of
control may occur and cause severe injury to the rider or others.

J. STAIRS

1. NEVER use this chair on stairs UNLESS you have someone to help you.
Doing so is likely to cause a fall or tip-over.

2. Persons who help you should read and follow the warnings
“For Attendants” (p. 16),and the “For Safe Use” (Section VII).

If you fail to heed these warnings damage to your chair, a fall,tip-over or loss of
control may occur and cause severe injury to the rider or others.

K. ESCALATORS

NEVER use this chair on an escalator, even with an attendant. If you do, a fall

or tip-over is likely.
If you fail to heed these warnings damage to your chair, a fall,tip-over or loss of
control may occur and cause severe injury to the rider or others.

▲

!

Before you assist a rider, be sure to read the warnings “For Attendants” (p. 16)
and follow all instructions that apply. Be aware that you will need to learn safe
methods best suited to your abilities.

A. LEARNING TO DO A “WHEELIE”

Follow these steps to help the rider learn to do a “wheelie”:

1. Read and follow the warnings for “WHEELIES.” (See p. 18)

2. Stand at the rear of the chair.You must be able to move with the chair to
prevent a tip-over.

3. Keep your hands BENEATH the push handles, ready to catch the rider if the
chair tips back.

4. When you are ready, have the rider place his or her hands on the forward part
of the handrims.

5. Have the rider make a quick BACKWARD movement of the rear wheels,
quickly followed by a hard FORWARD thrust. (This will tilt the chair up on the
balance point of the rear wheels.)

6. Have the rider make small movements of the handrims to stay in balance.

If you fail to heed these warnings damage to your chair, a fall,tip-over or loss of
control may occur and cause severe injury to the rider or others.

B. DESCENDING A CURB OR SINGLE STEP

Follow these steps to help a rider descend a curb or single step going BACKWARD:

1. Stay at the rear of the chair.

2. Several feet before your reach the edge of the curb or step, turn the chair
around and pull it backward.

3. While looking over your shoulder, carefully step back until you are off the curb
or stair and standing on the lower level.

4. Pull the chair toward you until the rear wheels reach the edge of the curb or
step.Then allow the rear wheels to slowly roll down onto the lower level.

5. When the rear wheels are safely on the lower level, tilt the chair back to its
balance point.This will lift the front casters off the curb or step.

6. Keep the chair in balance and take small steps backward.Turn the chair around
and gently lower front casters to the ground.

If you fail to heed these warnings damage to your chair, a fall,tip-over or loss of
control may occur and cause severe injury to the rider or others.

VII. WARNINGS: FOR SAFE USE

▲

!

24

25

930300 Rev.C

930300 Rev.C

VII. WARNINGS: FOR SAFE USE

▲

!

C. CLIMBING A CURB OR SINGLE STEP

Follow these steps to help the rider climb a curb or single step going FORWARD:

1. Stay behind the chair.

2. Face the curb and tilt the chair up on the rear wheels so that the front casters
clear the curb or step.

3. Move forward, placing the front casters on the upper level as soon as you are
sure they are past the edge.

4. Continue forward until the rear wheels contact the face of the curb or step.
Lift and roll the rear wheels to the upper level.

If you fail to heed these warnings damage to your chair, a fall,tip-over or loss of
control may occur and cause severe injury to the rider or others.

D. CLIMBING STAIRS

1. Use at least two attendants to move a chair and rider up stairs.

2. Move the chair and rider BACKWARD up the stairs.

3. The person at the rear is in control. He or she tilts the chair back to its
balance point.

4. A second attendant at the front firmly grasps a non-detachable part of the
front frame and lifts the chair up and over one stair at a time.

5. The attendants move to the next stair up. Repeat for each stair, until you reach
the landing.

If you fail to heed these warnings damage to your chair, a fall,tip-over or loss of
control may occur and cause severe injury to the rider or others.

E. DESCENDING STAIRS

1. Use at least two attendants to move a chair and rider down stairs.

2. Move the chair and rider FORWARD down the stairs.

3. The person at the rear is in control. He or she tilts the chair to the balance
point of the rear wheels and rolls it to the edge of the top step.

4. A second attendant stands on the third step from the top and grasps the chair
frame. He or she lowers the chair one step at a time by letting the rear wheels
roll over the stair edge.

5. The attendants move to the next stair down. Repeat for each stair, until you
reach the landing.

If you fail to heed these warnings damage to your chair, a fall,tip-over or loss of
control may occur and cause severe injury to the rider or others.

VII. WARNINGS: FOR SAFE USE

F. MAINTENANCE

1. Inspect and maintain this chair strictly per chart.

2. If you detect a problem, make sure to service or repair the chair before use.

3. At least once a year, have a complete inspection, safety check and service of
your chair made by an authorized supplier.

If you fail to heed these warnings damage to your chair, a fall,tip-over or loss of
control may occur and cause severe injury to the rider or others. For additional
maintenance information see Section XII: Maintenance.

▲

!

26

27

930300 Rev.C

930300 Rev.C

A. ANTI-TIP TUBES (OPTIONAL)

Anti-tip tubes can help keep your chair from tipping over backward in most
normal conditions.

1. Sunrise Recommends Use Of Anti-Tip Tubes:
a. UNLESS you are a skilled rider of this chair and are sure you are not at

risk to tip over.

b. Each time you modify or adjust your chair.The change may make it easier

to tip backward. Use anti-tip tubes until you adapt to the change, and are
sure you are not at risk to tip over.

2. When locked in place (in the “down” position) anti-tip tubes should be

BETWEEN 1 1/2 to 2 inches (38 mm to 51 mm) off the ground.

a. If set too HIGH, they may not prevent a tip-over.
b. If set too LOW, they may “hang up” on obstacles you can expect in normal

use. If this occurs, you may fall or your chair may tip over.

3. Keep Anti-Tip Tubes Locked In Place UNLESS:
a. You have an attendant; or
b. You have to climb or descend a curb, or overcome an obstacle, and can

safely do so without them. At these times, make sure anti-tip tubes are up,

out of the way.
If you fail to heed these warnings damage to your chair, a fall,tip-over or loss of
control may occur and cause severe injury to the rider or others.

B. ARMRESTS

Armrests detach and will not bear the weight of this chair.

1. NEVER lift this chair by its armrests.They may come loose or break.

2. Lift this chair only by non-detachable parts of the main frame.
If you fail to heed these warnings damage to your chair, a fall,tip-over or loss of
control may occur and cause severe injury to the rider or others.

C. CUSHIONS & SLING SEATS

1. Breezy sling seats and standard foam cushions are not designed for the relief

of pressure.

2. If you suffer from pressure sores, or if you are at risk that they will occur, you

may need a special seat system or a device to control your posture. Consult
your doctor, nurse or therapist to find out if you need such a device for your

well-being.
If you fail to heed these warnings damage to your chair, a fall,tip-over or loss of
control may occur and cause severe injury to the rider or others.

VIII. WARNINGS: COMPONENTS & OPTIONS

▲

!

VIII. WARNINGS: COMPONENTS & OPTIONS

D. FASTENERS

Many of the screws, bolts and nuts on this chair are special high-strength fasteners.
Use of improper fasteners may cause your chair to fail.

1. ONLY use fasteners provided by an authorized supplier (or ones of the same
type and strength, as indicated by the markings on the heads).

2. Over- or under-tightened fasteners may fail or cause damage to chair parts.

3. If bolts or screws become loose, tighten them as soon as you can.

If you fail to heed these warnings damage to your chair, a fall,tip-over or loss of
control may occur and cause severe injury to the rider or others.

E. FOOTRESTS

1. At the lowest point, footrests should be AT LEAST 2 1/2 INCHES (64 mm) off
the ground. If set too LOW,they may “hang up” on obstacles you can expect
to find in normal use.This may cause the chair to stop suddenly and tip for­ward.

2. To Avoid A Trip Or Fall When You Transfer:

a. Make sure your feet do not “hang up” or get caught in the space between

the footrests.

b. Avoid putting weight on the footrests, as the chair may tip forward.

3. NEVER lift this chair by the footrests. Footrests detach and will not bear the weight
of this chair. Lift this chair only by non-detachable parts of the main frame.

If you fail to heed these warnings damage to your chair, a fall,tip-over or loss of
control may occur and cause severe injury to the rider or others.

F. PNEUMATIC TIRES

Proper inflation extends the life of your tires and makes your chair easier to use.

1. Do not use this chair if any of the tires is under- or over-inflated. Check week­ly for proper inflation level, as listed on the tire sidewall.

2. Low pressure in a rear tire may cause the wheel lock on that side to slip and
allow the wheel to turn when you do not expect it.

3. Low pressure in any of the tires may cause the chair to veer to one side and
result in a loss of control.

4. Over-inflated tires may burst.

If you fail to heed these warnings damage to your chair, a fall,tip-over or loss of
control may occur and cause severe injury to the rider or others.

▲

!

VIII. WARNINGS: COMPONENTS & OPTIONS

J. QUICK-RELEASE AXLES (OPTIONAL)

1. Do not use this chair UNLESS you are sure that both quick-release rear axles are
locked. An unlocked axle may come off during use and cause a fall.

2. An axle is not locked until the quick-release button pops out fully.
An unlocked axle may come off during use, resulting in a fall, tip-over or loss of
control and cause severe injury to the rider or others.

If you fail to heed these warnings damage to your chair, a fall,tip-over or loss of con­trol may occur and cause severe injury to the rider or others.

K. REAR WHEELS

A change in set-up of the rear wheels will affect the center of balance of your chair.

1. The farther you move the rear axles FORWARD, the more likely it is that your
chair will tip over backward.

2. Consult your doctor, nurse or therapist to find the best rear axle set-up for your
chair. Do not change the set-up UNLESS you are sure you are not at risk to tip
over.

3. Adjust the rear wheel locks after you make any change to the rear axles.
a. If you fail to do so, the locks may not work.
b. Make sure lock arms embed in tires at least 1/8 inch (3 mm) when locked.

If you fail to heed these warnings damage to your chair, a fall,tip-over or loss of con­trol may occur and cause severe injury to the rider or others.

L. REAR WHEEL LOCKS

Rear wheel locks are NOT designed to slow or stop a moving wheelchair. Use the only
to keep the rear wheels from rolling when your chair is at a complete stop.

1. NEVER use rear wheel locks to try to slow or stop your chair when it is
moving. Doing so may cause you to veer out of control.

2. To keep the rear wheels from rolling, always set both rear wheel locks when you
transfer to or from your chair.

3. Low pressure in a rear tire may cause the wheel lock on that side to slip and may
allow the wheel to turn when you do not expect it.

4. Make sure lock arms embed in tires at least 3/8 inch (10 mm) when locked. If you
fail to do so, the locks may not work.

If you fail to heed these warnings damage to your chair, a fall,tip-over or loss of con­trol may occur and cause severe injury to the rider or others.

▲

!

28

29

930300 Rev.C

930300 Rev.C

VIII. WARNINGS: COMPONENTS & OPTIONS

G. POSITIONING BELTS (OPTIONAL)

Use positioning belts ONLY to help support the rider’s posture. Improper use of
these belts may cause severe injury to or death of the rider.

1. Make sure the rider does not slide down in the wheelchair seat. If this occurs, the
rider may suffer chest compression or suffocate due to pressure from the belts.

2. The belts must be snug, but must not be so tight that they interfere with breath­ing.You should be able to slide your open hand, flat, between the belt and the
rider.

3. A pelvic wedge or a similar device can help keep the rider from sliding down in
the seat. Consult with the rider’s doctor, nurse or therapist to find out if the
rider needs such a device.

4. Use positioning belts only with a rider who can cooperate. Make sure the rider
can easily remove the belts in an emergency.

5. NEVER Use Positioning Belts:
a. As a patient restraint. A restraint requires a doctor’s order.
b. On a rider who is comatose or agitated.
c. As a motor vehicle restraint. In an accident or sudden stop the rider may be

thrown from the chair.Wheelchair seat belts will not prevent this, and fur-

ther injury may result from the belts or straps.
If you fail to heed these warnings damage to your chair, a fall,tip-over or loss of
control may occur and cause severe injury to the rider or others.

H. POWER DRIVE

Do not install a power drive on any Breezy wheelchair. If you do:

1. It will affect the center of balance of your chair and may cause a fall or tip-over.

2. It will alter the frame and void the warranty.
If you fail to heed these warnings damage to your chair, a fall,tip-over or loss of
control may occur and cause severe injury to the rider or others.

I. PUSH HANDLES (OPTIONAL)

When you have an attendant, make sure that this chair has push handles.

1. Push handles provide secure points for an attendant to hold the rear of this

chair, to prevent a fall or tip-over. Make sure to use push handles when you have
an attendant.

2. Check to make sure push handle grips will not rotate or slip off.
If you fail to heed these warnings damage to your chair, a fall,tip-over or loss of
control may occur and cause severe injury to the rider or others.

▲

!

A. TO MOUNT & REMOVE REAR WHEELS
(QUICK RELEASE OPTION)

IX. CHAIR BASICS

Note: Axle is not locked until:

a. The quick-release button pops out

fully. (Fig.A)

b. The ball bearings are fully visible on

the outside of the sleeve.

1. To Install Wheel:

a. Depress quick-release button (1) fully.

This will release tension on ball bear-

ings at other end.
b. Insert axle through hub of rear wheel.
c. Keep pressure on button (1) as you

slide axle (2) into axle sleeve (3).
d. Release button to lock axle in sleeve.

Adjust axle if it does not lock.
e. Repeat steps on other side.

2. To Remove Wheel:

a. Depress quick-release button (1) fully.
b. Remove wheel by sliding axle (2) out

of axle sleeve (3).
c. Repeat steps on other side.

1. Quick-release button

Figure A

2

3

30 31

930300 Rev.C 930300 Rev.C

VIII. WARNINGS: COMPONENTS & OPTIONS

▲

!

M. MODIFIED SEAT SYSTEMS

Use of a seat system not approved by Sunrise may alter the center of balance of
this chair. This may cause the chair to tip over.

1. Do not change the seat system of your chair UNLESS you consult your
authorized supplier first.

2. Use of a seat system not approved by Sunrise may affect the folding mechanism
of this chair.

3. Use of a seating system not provided by Sunrise is prohibited for transit use.

If you fail to heed these warnings damage to your chair, a fall,tip-over or loss of
control may occur and cause severe injury to the rider or others.

N. UPHOLSTERY FABRIC

1. Replace worn or torn fabric of seat and seat back as soon as you can. If you fail
to do so, the seat may fail.

2. Sling fabric will weaken with age and use. Look for fraying or thin spots, or
stretching of fabrics at rivet holes.

3. “Dropping down” into your chair will weaken fabric and result in the need to
inspect and replace the seat more often.

4. Be aware that laundering or excess moisture will reduce flame retardation of
the fabric.

If you fail to heed these warnings damage to your chair, a fall,tip-over or loss of
control may occur and cause severe injury to the rider or others.

32

33

930300 Rev.C 930300 Rev.C

A. SET-UP

1. Fasteners

Use of improper fasteners may cause the chair to fail. Over or under-tightened fasten­ers may fail or cause damage to chair parts. If bolts or screws become loose, tighten
them as soon as you can.

a. Many of the screws and bolts on this chair are special high-strength

fasteners.

b. Many nuts are the Nylock type.They have a plastic insert to help

prevent loosening.

c. ONLY use screws, bolts and nuts provided by an authorized supplier (or

fasteners of the same type and strength, as indicated by the markings on
the heads).

3. Washers & Spacers

a. Make a note of the position of washers and spacers before disassembly.
b. To avoid damage to the frame, position washers and spacers correctly

when you reassemble parts.

Note on Torque Settings: A torque setting is the optimum tightening which

should be made on a particular fastener. A torque wrench which measures in.-lbs

should be used when tightening fastener on Breezy wheelchairs. Unless otherwise

noted, use a torque setting of 50-65 in.-lbs. (5.6 -7.3 N.m) for all fasteners.

B. TOOLS

1. Basic Tool Kit

To set up, adjust and maintain your chair, you will need the following tools:

a. 7/16” box and open-end wrench
b. 1/2” box and open-end wrench
c. 3/4” box and open-end wrench
d. 1” socket wrench
e. 5/32” Allen wrench
f. 3/16” Allen wrench
g. Phillips head screwdriver #2
h. Custom axle wrench (or a 1/2” open-end wrench)

You can obtain a multi-purpose tool kit from Sunrise or buy the tools you need
from a hardware store.

X. SET UP & ADJUSTMENT

B. TO FOLD & UNFOLD CHAIR

NEVER let your fingers come between the seat rail and the frame rail when

you open or fold this chair.This may cause a pinch- or crush-type injury.

Note: You can remove quick-release wheels before you fold chair (and re-mount
them before you unfold chair).

1. To Fold Chair:

a. Make sure footrests are out of the way before you fold chair. (Swing-away,

flip up or remove footrests.)
b. Remove cushion (if any).
c. Grasp center of seat sling and lift sharply until chair folds.

2. To Unfold Chair:

a. Move to one side of chair. Check to make sure footrests do not interfere.
b. Tilt chair toward you far enough to take the weight off the opposite wheel.
c. Push down on the seat rail closest to you until chair opens fully.
d. Make sure seat rail tubes snap into frame saddles.

IX. CHAIR BASICS

34 35

930300 Rev.C 930300 Rev.C

1. To Install

a. Depress button (1) to draw second

button (not shown) inside anti-tip
tube (3).

b. Insert tube (3) into frame (4).

Release button.

c. Rotate tube (3) until button (2) locks

in place in mounting hole (not
shown).

2. To Turn Anti-Tip Tube Up

a. Depress button (1) to draw second

button (not shown) inside anti-tip
tube (3).

b. Hold button in and turn anti-tip tube

up. Release button.

c. Repeat with other side.

3. To Adjust Wheel Height

a. Depress button (6).
b. Raise or lower wheel tube (7) to

one of three predrilled holes and
lock it in place.

c. Raise or lower wheel tube (7) to

one of three predrilled holes and
lock it in place.

Note: You may need to use a longer or shorter

wheel tube section to attain correct height of

1 1/2” to 2” (38 mm to 51 mm). You can obtain

these from your authorized supplier.

BREEZY 600 SERIES

1. Inserting Anti-Tip Tubes Into
Receiver

a. Press the rear anti-tip release lever on

the anti-tip tube so that both release

pins are drawn inside.
b. Insert into the anti-tip tube receiver.
c. Turn the anti-tip tube down until

release pin is through the receiver

mounting hole.
d. Insert second anti-tip tube the same way.

X. SET UP & ADJUSTMENT

1

3

6

7

2. Torque Wrench

If you plan to adjust and maintain this chair

yourself, Sunrise recommends that you
use a torque wrench.

Note: A torque setting is the optimum tightening

which should be made on a particular fastener.

A torque wrench which measures in.-lbs. should

be used when tightening fasteners on Breezy

wheelchairs. Unless otherwise noted,use a torque

setting of 50-65 in./lbs. (5.6-7.3 N.m) when setting-

up this wheelchair.

When properly set up, your chair will roll smoothly
and easily. All components should also work
smoothly.If you detect a problem, be sure to
correct it before using this chair.

C. TO FIND & CORRECT A PROBLEM

1. Review the TROUBLESHOOTING section
to see if your chair has one of the listed
symptoms. If so, follow steps to solve the
problem.

2. Follow steps in this section to make sure
set up is correct.

3. If steps 1 and 2 do not work, consult your
authorized supplier for help.

4. If you still have a problem, contact customer
service at 800.456.8165.

D. ANTI-TIP TUBES (Optional)

Anti-tip tubes are recommended unless you are a
skilled rider of this chair and are sure you are not
at risk to tip over.

The following is recommended for all Breezy

models except the 600 (listed next):

Note: When locked in place, anti-tip tube wheels

should be between 11/2” to 2” (38 mm to 51 mm)

off the ground. If set too high, they may not prevent

a tip over. If set too low, they may “hang-up” and

cause a fall or tip over.

X. SET UP & ADJUSTMENT

4

36 37

930300 Rev.C 930300 Rev.C

F. CASTER FORKS

Note: Two-hole caster forks allow you to adjust

the seat height or seat angle.

a. For a standard 18 1/2” (470 mm) front

seat height:

1. Remove caster wheel bolt (1) and
bearing spacers (not shown).

2. Move caster into the bottom fork
position (2).

3. Replace caster wheel bolt and
bearing spacers.Tighten bolt.

4. Repeat steps on other side. Make
sure to adjust both the same.

b. For a low 17 1/2” (445 mm) front seat

height:

1. Remove caster wheel bolt and
bearing spacers (1).

2. Move caster into the top fork
position (3).

3. Replace caster wheel bolt and

bearing spacers.Tighten bolt.

4. Repeat steps on other side. Make

sure to adjust both the same.

G. REAR WHEELS - THREADED

OR FIXED OFFSET AXLES

(BREEZY 510)

Note: Use a torque setting of 150-175 in./lbs.

(16.9-19.8 N.m) when setting-up axles.

1. Installation

a. Remove threaded axles, axle bolts and

hub caps from plastic bag.

b. Remove inside bolt from axle and

insert the axle through one of two
holes in the rear frame tube.

c. The hole you choose affects the rear

seat height place the axle in the lower
hole for level seating; place the axle
in the upper hole for lower rear
seat height.

X. SET UP & ADJUSTMENTX. SET UP & ADJUSTMENT

3. Turning Anti-Tip Tubes Up

Turn anti-tip tubes up when being pushed

by attendant, overcoming obstacles or
climbing curbs.

a. Press the rear anti-tip tube release lever.
b. Hold lever in and turn anti-tip tube up.
c. Release lever.
d. Repeat with second anti-tip tube.
e. Remember to return anti-tip tubes

to down position after completing
maneuver.

E. STANDARD & LOW FRONT

SEAT HEIGHTS

Note: Adjust seat height for body and mechanical

efficiency. Be aware that a change in seat height may

require a change in the size of the front caster

stems or forks.

1. If you raise the seat too high, you may “out-adjust”
the caster forks. If this occurs, the seat will tilt
toward the front and may cause the rider to fall.

2.To avoid this, you will need to use a longer caster
fork or fork stem.

1. Adjustment

a. For a standard 18 1/2” (470 mm) front

seat height:

1. Remove the axle bolt.

2. Set axle in the bottom frame setting.
Re-attach axle bolt and tighten.

3. Repeat steps on other side. Make
sure both sides are the same height.

b. For a low 17 1/2” (445 mm) front

seat height:

1. Remove the axle bolt.

2. Set axle in the top frame setting. Re­attach axle bolt and tighten.

3. Repeat steps on other side. Make
sure both sides are the same height.

Note: Use a torque setting of 150 to 175 in./lbs.
(16.9-19.8 N.m) for axle nuts.

2. Seat Angle (not available on BREEZY 500)
If you change the seat height, make sure

you adjust the front casters to attain the
proper seat angle. (The seat should be
slightly higher at the front.)

1

3

2

38 39

930300 Rev.C 930300 Rev.C

2. Wheel Locks - Quickie Style (Option)

Quickie style high-mount wheel locks are

installed at Sunrise unless you have

requested otherwise.

Note: Use a torque setting of 70-80 in./lbs.

(7.9-9.0 N.m) to tighten when setting up wheel locks.

To install or adjust high-mount wheel lock:

a. Loosen the screws on the top of each

clamp. Do not attempt to remove one
screw at a time.

b. Slide assembly toward rear wheel, until

clamp embeds into tire, to prevent wheel
movement when in locked position.

I. FLIP-BACK ARMRESTS

Note: Non-removable; we install this armrest at

the factory.

J. FLIP-BACK HEIGHT ADJUSTABLE

ARMRESTS (Optional)

Note: Armrest is removable; you can adjust the

height of the armrest pad.

1. To Flip Armrest Back

Push latch lever (1) toward tube to “flip”

or “tilt” armrest back.

2. Installation

a. Tilt armrest back and insert rear arm

tube (2) into receiver (3).

b. Tilt armrest forward.This will engage

pin to secure rear arm tube.

c. Push armrest down until front tube

locks in place.

3. Removal

a. Push latch lever (1) toward tube.
b. Tilt armrest back toward rear of chair.
c. Pull up on armrest (pin holding arm-

rest in rear tube will release).

4. Height Adjustment

a. Pull back on upper lever (4) to release.
b. Slide armrest up or down to chosen

height.

c. Release upper lever (4). Move armrest

slightly to make sure it locks in place.

X. SET UP & ADJUSTMENTX. SET UP & ADJUSTMENT

2. Axle Positioning (Threaded or Offset)

a. When the axle is placed in the lower

axle position, the caster should also
be placed in the lower caster fork
position.

b. When the axle is placed in the top

axle position, the caster should also be
placed in the top caster fork position
(except when using pneumatic rear
tires - pneumatic rear tires are always
placed in the top axle position).

H. REAR WHEEL LOCKS

The Breezy Series wheelchairs come with
wheel locks.We install wheel locks at

the factory unless you request otherwise.

Note: Use a torque setting of 25-40 in./lbs.

(2.8-4.5 N.m) to tighten wheel lock bolts.

Make sure lock arms embed in tires at least
1/8” (3 mm) when locked. If you fail to do so, the
locks may not keep the rear wheels from rolling.

1. High-Mount Wheel Locks

(push-to-lock or pull-to-lock)

To install or adjust:

a. Use a open-end wrench to loosen

two bolts (1) on top clamp (2).

b. Turn each bolt counter-clockwise one-

quarter turn; then loosen each bolt
two turns until you can remove both
bolts. (Alternate, to keep bolts from
binding.)

c. Side clamp (2) toward rear wheel until

lock arm (3) embeds in tire at least

1/8” (3 mm) when locked.
d. Alternate as you retighten bolts (1).
e. Repeat steps on other side.

2

1

3

1

2

3

4

40 41

930300 Rev.C 930300 Rev.C

X. SET UP & ADJUSTMENT

K. SWING-AWAY HANGERS &

FOOTRESTS (60º OR 70º)

1. Installation

a. Place swing-away pivot saddle into the

receiver on front frame tube with the
footrest facing outward from the frame.

b. Rotate the footrest inward until it

locks into place on locking bolt.

2. Removal

a. To remove footrest, push release latch

toward the frame.

b. Rotate footrest outward and lift.

3. Height-Adjustment

a. Remove retaining bolt in the frame tube.
b. Slide footrest tubes up or down inside

frame tube to desired height.

c. Align predrilled holes in footrest and

reinsert bolts.

d. Tighten bolts.

4. Footplate Angle-Adjustment

a. Loosen the retaining bolt in the frame

tube.

b. Reposition footplate to desired angle

and re-tighten bolt.

X. SET UP & ADJUSTMENT

Breezy 500

Breezy 510 & 600

L. ARTICULATING LEGREST &

ELEVATING LEGREST (Optional)

1. Installation

a. Follow same steps as for swing-away

hangers and footrests. (p. 40)

2. Adjustment

a. List legrest to chosen position. Legrest

will lock in place.

b. To lower legrest, press release lever

(1) forward and lower legrest to chosen
position. Legrest will lock in place.

M. CASTER PLATES

(not available on the 500)

Note: Use a torque setting of 50-65 in./lbs.

(5.6-7.3 N.m) when adjusting caster angle.

1. Angle Adjustment

a. Loosen the two eccentric bolts that

secure the caster assembly. Do not
remove the clevis pin.

b. Place a large right triangle against the

table surface and the front surface of
the caster bearing housing.This will
align the caster stem rotational axis
perpendicular to the floor surface.

c. When alignment is satisfactory,

retighten the two eccentric bolts.

d. Repeat the process for the other.

1

42 43

930300 Rev.C 930300 Rev.C

BREEZY 500 & 510

Note: Use a torque setting of 20-30 in./lbs.

(2.3-3.4 N.m) to tighten bolts.

1. Height Adjustment

a. Remove bolt which attaches metal

upholstery tab to frame tube.

b. The backrest tube telescopes into the

frame and is secured by a bolt on the

side of the frame.
c. Remove bolt.
d. There are three holes, 1” apart, you

may choose from to set the back

height.
e. After selecting the proper height reat-

tach the metal upholstery tab to bolt.
f. Tighten nut and bolt assembly.

X. SET UP & ADJUSTMENT

N. CASTER MOUNTING

(not available on the 500)

1. Forward or Rearward Placement

a. Remove caster housing covers.
b. Remove the two eccentric bolts from

each caster.
c. Move left-side caster to right side.
d. Move right-side caster to left side.
e. Remount casters to caster bracket.

Note: Sunrise recommends mounting casters for-

ward whenever possible.

O. BACKREST

BREEZY 600

1. Height Adjustment

a. Remove backrest material.
b. There are three holes, 1” apart, in

each backrest tube (1).The tube tele-

scopes into the frame and is secured

by a bolt on the side of the frame.

Choose one of the three holes to set

the back height.
c. Remove bolt (2) from each backrest

tube.
d. Choose the proper height. Slide the

upholstery back on.

Note: Do not attach the overlap portion.

e. Attach tab (3) to bolt (2) and tighten

nut (4).
f. Insert nylon tie (5) through grommets

(6). Secure tie and cut off excess nylon.

X. SET UP & ADJUSTMENT

2

3

4

1

5, 6

44 45

930300 Rev.C 930300 Rev.C

XII. MAINTENANCE

A. INTRODUCTION

1. Proper maintenance will improve performance and extend the useful life
of your chair.

2. Clean your chair regularly. This will help you find loose or worn parts and
make your chair easier to use.

3. Repair or replace loose, worn,bent or damaged parts before using this
chair.

4. To protect your investment, have all major maintenance and repair work
done by your authorized supplier.

If you fail to heed these warnings your chair may fail and cause severe injury

to the rider or others.

1. Inspect and maintain this chair strictly per chart.

2. If you detect a problem, make sure to service or repair the chair before use.

3.At least once a year, have a complete inspection, safety check and service of
your chair made by an authorized supplier.

B. MAINTENANCE CHART

Tire inflation level

Wheel locks

All fasteners for wear and tightness

Armrests

Axle and axle sleeves

Wheels, tires and spokes

Casters

Anti-tip tubes

Frame

Upholstery

Service by Authorized Supplier

CHECK...

✓
✓

✓

✓

✓
✓
✓
✓

✓
✓

✓

Annually

6 Months

3 Months

Weekly

You will need to adjust your chair from time to time for best performance (espe­cially if you alter the original settings). This chart gives you a first solution, then a
second and a third if needed. You may need to look farther to find the best solu­tion for a specific problem.

Note: To keep track of your progress, make only ONE change at a time.

Left Turn In Chair

Right Turn In Chair

Looseness In Chair

Sluggish Turning

Squeaks And Rattles

Caster Flutter

Add a spacer washer between the plastic saddle and the caster plate
on the top of the left caster plate.

Make sure tire pressure is correct and equal in both rear tires and
front caster tires, if pneumatic.

Make sure all nuts and bolts are snug.

Make sure all spokes and nipples are tight on radial spoke wheels.

Use Tri-Flow Lubricant (Teflon®-based) between all modular frame
connections and parts.

Check for proper caster plate adjustment. See instructions for
caster plate adjustment.

SYMPTOMS

SOLUTIONS

✓✓✓✓

✓✓✓✓✓

✓

✓✓✓
✓✓

✓

✓

Add a spacer washer between the plastic saddle and the caster plate
on the top of the right caster plate.

Add a spacer washer between the plastic saddle and the caster plate
on the bottom right caster plate retaining bolts.

Add a spacer washer between the plastic saddle and the caster plate
on the bottom right caster plate retaining bolts.

✓

Make sure there is an equal number of camber washers on each axle
plate.

Make sure both front casters touch the ground simultaneously. If
they do not, add the proper spacers between the bottom bearing of
the caster plate and fork stem nut until they do. Make sure you
check for this problem on a flat surface.

✓✓

✓

✓

✓

✓

✓

XI. TROUBLESHOOTING

46 47

930300 Rev.C 930300 Rev.C

XIII. SUNRISE LIMITED WARRANTY

A. LIFETIME LIMITED WARRANTY

Sunrise warrants the frame and quick-release axles of this wheelchair against

defects in materials and workmanship for the life of the original purchaser.

B. FOR TWO (2) YEARS

We warrant all Sunrise-made parts and components of this wheelchair against

defects in materials and workmanship for two years from the date of first con­sumer purchase.

C. LIMITATIONS

1. We do not warrant:

• Tires and tubes, upholstery, armrests and push-handle grips.

• Damage from neglect, misuse, or from improper installation or repair.

• Damage from exceeding weight limit of 250 pounds (113.6 kg).

2. This warranty is VOID if the original chair serial number tag is removed
or altered.

3. This warranty applies in the USA only.Check with your supplier to find
out if international warranties apply.

D. WHAT WE WILL DO

1. Our sole liability is to repair or replace covered parts.This is the exclusive
remedy for consequential damages.

E. WHAT YOU MUST DO

1. Obtain from us through an authorized supplier, while this warranty is
in effect, prior approval for return or repair of covered parts.

2. Return the wheelchair or part(s), freight pre-paid, to Sunrise Mobility
Products Division at: 2842 Business Park Avenue, Fresno, CA 93727-1328.

3. Pay the cost of labor to repair, remove or install parts.

F. NOTICE TO CONSUMER

1. If allowed by law, this warranty is in place of any other warranty (written
or oral, express or implied, including a warranty of merchantability, or
fitness for a particular purpose).

2. This warranty gives you certain legal rights.You may also have other rights
that vary from state to state.

Record your serial number here for future reference:

________________________

C. MAINTENANCE TIPS

1. Axles & Axle Sleeves:

Check axles and axle sleeves every six months to make sure they are tight.

Loose sleeves will damage the axle plate and will affect performance.

2. Tire Air Pressure:

Check air pressure in pneumatic tires at least ONCE A WEEK. The wheel

locks will not grip properly if you fail to maintain the air pressure shown
on tire sidewall.

D. CLEANING

1. Paint Finish

a. Clean the paint finish with mild soap at least once a month.
b. Protect the paint with a coat of non-abrasive auto wax every three

months.

2. Axles and Moving Parts

a. Clean around axles and moving parts WEEKLY with a slightly damp

(not wet) cloth.

b. Wipe off or blow away any fluff,dust, or dirt on axles or moving parts.

Note: You do not need to grease or oil the chair.

3. Upholstery

a. Hand-wash (machine washing may damage fabric).
b. Drip-dry only. DO NOT machine dry as heat will damage fabric.

E. STORAGE TIPS

1. Store your chair in a clean, dry area. If you fail to do so, parts may rust
or corrode.

2. Before using your chair, make sure it is in proper working order. Inspect
and service all items on the "Maintenance Chart." (See p. 45)

3. If stored for more than three months, have your chair inspected by an
authorized supplier before use.

XII. MAINTENANCE

Sunrise Home Healthcare Group

Mobility Products Division

7477 East Dry Creek Parkway • Longmont, Colorado • 80503 USA

[phone] or [phone]

in Canada [phone]

Manufactured under one or more of the following patents:

U.S. Patent # 5,062,677;5,149,173; 5,211,446; 5,352,023;5,407,248; plus other foreign patents

© 1998, Sunrise Medical 5.98

930300 Rev.C