Sunex Tools SX6215 User Manual [en, es, fr]

Quiet has a new name

WARNING

ADVERTENCIA

AVERTISSEMENT

LOW VIBRATION AIR SAW
SIERRA NEUMÁTICA DE BAJA VIBRACIÓN
SCIE PNEUMATIQUE À BASSE VIBRATION

Product Safety Information
Información de seguridad del producto
Informations de sécurité liées au produit

SX6215

Save these instructions
Guarde estas instrucciones
Sauvegarder ces instructions

Read this manual before
operating tool.

Always wear eye protection
when operating or performing
maintenance on this tool.

Always wear hearing
protection when operating
this tool.

SX6215_manual_072811.indd 1 7/28/11 3:47 PM

Lea este manual antes de operar esta
herramienta.

Siempre lleve puesto protección de
ojos al momento de operar o realizar
mantenimiento a esta herramienta.

Siempre lleve puesto protección del oído
al momento de operar esta herramienta.

Sauvegarder ces instructions.

Veuillez lire le présent manuel avant
d’utiliser l’outil.

Toujours porter le dispositif de
protection antibruit lorsque vous
utilisez cet équipement.

To reduce the risk of injury, anyone using, repairing, maintaining, or

WARNING

changing accessories on this tool must read and understand these
instructions before performing any of these tasks.

Always inspect, operate, and maintain this tool in
accordance with American National Standards Institute
Safety Code of Portable Air Tools (ANSI B186.1) and any
other applicable safety codes and regulations.

These tools are rated at 90 psi / 6.2 bar max air
pressure for safety, top performance, and maximum
durability of parts; do not exceed this pressure while
the tool is running.

Always shut off air supply, drain hose of air pressure
and disconnect tool from air supply when not in use,
before changing accessories, or when making repairs.

Never direct air at yourself or anyone else.
Always wear impact-resistant eye and face protection

when operating or performing maintenance on this tool.
High sound levels can cause permanent hearing loss.

Always use hearing protection when using this tool as
recommended by your employer or OSHA regulation.

Do not wear jewelry or loose fitting clothes.
Do not use quick disconnect couplings at tool. See

operating instructions for proper set up.
Whipping hoses can cause serious injury. Always

carefully check for damaged or loose hoses and fittings
before operating this tool.

Avoid direct contact with accessories during and after
use. Gloves should be worn to reduce the risk of cuts
or burns.

Cutting with this tool will create sharp edges, always
wear gloves to protect your hands.

Never force tool to cut faster than rated capacity.
Slipping, tripping, and/or falling while operating air tools

can be a major cause of serious injury or death. Be
aware of your surroundings and any excess hose left on
the walking or working surface.

Pneumatic tools can cause vibration in use. Vibration,
repetitive motions or uncomfortable positions over
extended periods of time may be harmful to your hands
and arms. Discontinue use of tool if discomfort, tingling
feeling or pain occurs. Consult a physician before
resuming use if any of these symptoms occur.

Do not stretch or overreach while using this tool.
If tool appears to malfunction, remove from service

immediately and arrange for repair.
Never use tool if there is any chance of coming into

contact with line electricity.
Use only Sunex certified spare parts for any repair made

to tool. Repairs should only be performed by properly
trained persons.

Do not lock, tape or wire the tool valve in the "on/off"
position.

Do not allow the exhaust air to come in contact with hot
surfaces or flames.

Avoid inhaling dust or handling debris from the work
process, which can be harmful to your health. Use dust
extraction and wear respiratory protective equipment
when working with materials which produce airborne
particles.

Some dust created by power sanding, sawing, grinding,
drilling and other construction activities contains
chemicals known to the State of California to cause
cancer and birth defects or other reproductive harm.
Some examples of these chemicals are:

- Lead from lead based paints

- Crystalline silica bricks and cement and other
masonry products

- Arsenic and chromium from chemically-treated
lumber
Your risk from these exposures varies, depending on
how often you do this type of work. To reduce your
exposure to these chemicals: work in a well ventilated
area, and work with approved safety equipment, such
as those dust masks that are specially designed to filter
out microscopic particles.

Additional Safety Warnings

Do not modify this tool or its accessories.
This tool is not recommended for use in explosive

atmospheres or underwater use.
Operators and maintenance personnel must be

physically able to handle the bulk, weight, and power
of this tool.

This tool is for professional use only.

SAFETY INSTRUCTIONS - DO NOT DISCARD - GIVE TO USER

SX6215: Parts Breakdown & Operating Manual 2 7/28/11

SX6215_manual_072811.indd 2 7/28/11 3:47 PM

Instruction Manual

This product is designed for cutting plastics, composites and
metals. No other use is permitted.

Air Supply Requirements

Tool is designed to operate at 90 psi (6.2 bar) at free speed
measured at the tool, of clean, dry air. Operating this tool at
higher pressures will drastically reduce the tool life and could
cause injury.

The air inlet thread on this tool is a standard 1/4" NPT.
Line pressure should be increased for any unusually long
air hose run (over 25 feet). Minimum hose diameter should
be 3/8" I.D. and all fittings should have the same inside
diameter. See diagram below for proper air supply setup.

Do Not Install

Quick Coupling

Here

Hose

Nipple

Whip Hose

Nipple

Regulator Oiler Quick Coupler Leader

Filter

Air Supply

Drain Daily

EC DECLARATION OF CONFORMITY

We, Sunex International Inc., 315 Hawkins Rd, Travelers Rest,
SC 29690, declare under our sole responsibility that the
product to which this declaration relates, is in conformity with
the requirements of the Council Directive of June 1998 on the
approximation of the laws of the Member States relating to
machinery. (EN792, 98/37/EC)

Harmonized Standards Applied:

EN 792-6

National Standards Applied:

ISO 8662-7, ISO 15744-2002
Machine Name:
SX6215 Low Vibration Air Saw
Serial No.:
SB011400001 or higher
Techical Data:
Strokes Per Minute: 10,000
Air Pressure: 90 psi (6.2 bar)

Noise and Vibration Declaration

Tool produces a noise level (no load) of 84.4 dBA
sound pressure with 3 dBA uncertainty per
EN ISO15744-2002. Vibration level is 2.4 m/s²
tested per EN 28662-1 & EN28662-7:1997

Signature of Issuer:

Lubrication

Name and Position of Issuer: John Stratton, Product Manager
Lubricate the tool each day after use with quality SAE #10
air motor oil. Add the oil to the air inlet or into the hose at the

Sunex International Inc.

Date of Issue: July 13, 2011
nearest connection to the air supply, then run the tool until
all excess oil is expelled from the exhaust. Total oil quantity
needed for this procedure is approximately 1 ounce.

Specifications

Strokes Per Minute ............................................ 10,000 SPM

Stroke Length .................................................0.38" (9.7mm)

Length .............................................................6.7" (170mm)

Weight ...................................................... 0.97 Lbs. (0.44kg)

Avg. Air. Cons. ...............................................3 cfm (85 l/min)

Air Inlet ................................................................... 1/4" NPT

Min. Hose Size ............................................ 3/8" I.D. (10mm)

SX6215: Parts Breakdown & Operating Manual 3 7/28/11

SX6215_manual_072811.indd 3 7/28/11 3:47 PM

SX6215

LOW
VIBRATION
AIR SAW

408

409

410

107

309

REF. PART
NO. NO. DESCRIPTION QTY.

101 RS6215101 Collet 1
102 RS6215102 Blade Holder Guide 1
103 RS6215103 Blade Guard 1
104 RS2215104 Flat Washer 1
105 RS6215105 Half Round H.D. Hex Bolt 1
106 RS6215106 Hex Soc. H.D. Screw 1
107 * Replacement Saw Blade 1
108 RS2215108 Hex Soc. H.D. Screw 2
201 RS6215201 Housing 1
202 RS6215202 End Cap 1
203 RS6215203 O-Ring 1
204 RS6215204 O-Ring 1
205 RS6215205 Pin 2
206 RS6215206 Deflector 1
207 RS6215207 Lock Ring 1
209 RS6215209 Protective Cushion 1
301 RS76621 O-Ring 1
302 RS6215302 Magazine Unit 1
303 RS6215303 Feed Bumper 1
304 RS6215304 Piston Shaft Unit 1
305 RS6215305 Cylinder Unit 1
306 RS2215309 Discharge Sheet 1
307 RS6215307 Collar 1

411

301

101

411

302

103

303

105

104

108

102

106

304

406
405

201

209

311

319

305

306

307

310

308

203

318

316

312

401

318

202

314

404
403

402

407

204

REF. PART

NO. NO. DESCRIPTION QTY.

309 RS6215309 Hex Soc. H.D. Bolt 4

310 RS6215310 Spring 1

311 RS6215311 Shock-Reduction Spring 1

312 RS6215312 Feed Bumper 1

314 RS6215314 Muffler 1

315 RS6215315 Hex Soc. H.D. Bolt 2

316 RS6215316 Muffler Cap 1

318 RS6215318 Pin 2

319 RS6215319 Lock Ring 1

401 RS6215401 Body-Throttle Valve 1

402 RS6215402 Valve Stem Unit (Incl. #403) 1

403 O-Ring (Incl. w/ #402) 1

404 RS2215404 Valve Stem Spring 1

405 RS6215405 Valve Seal 1

406 RS6215406 Lock Ring 1

407 RS2215406 O-Ring 1

408 RS6215408 Trigger Assy (Incl. #409, 410,

& 411) 1

409 Safety (Incl. w/ #408) 1

410 Spring (Incl. w/ #408) 1

411 RS1837109 Spring Pin 2

* Available as RS18TPIBLADES (5 PK); RS24TPIBLADES (5 PK);

RS32TPIBLADES (5 PK)

315

315

207

206

205

308 RS6215308 Top Stem Valve 1

SX6215: Parts Breakdown & Operating Manual 4 7/28/11

SX6215_manual_072811.indd 4 7/28/11 3:47 PM