Sunex Tools SX6210 User Manual [en, es, fr]

REVERSIBLE CUT-OFF TOOL
HERRAMIENTA DE CORTE REVERSIBLE
OUTIL À TRONÇONNER RÉVERSIBLE

Quiet has a new name

SX6210

Read this manual before
operating tool.

Always wear eye protection
when operating or performing
maintenance on this tool.

Always wear hearing
protection when operating
this tool.

Lea este manual antes de operar esta
herramienta.

Siempre lleve puesto protección de
ojos al momento de operar o realizar
mantenimiento a esta herramienta.

Siempre lleve puesto protección del oído
al momento de operar esta herramienta.

Sauvegarder ces instructions.

Veuillez lire le présent manuel avant
d’utiliser l’outil.

Toujours porter le dispositif de
protection antibruit lorsque vous
utilisez cet équipement.

WARNING

ADVERTENCIA

AVERTISSEMENT

Product Safety Information
Información de seguridad del producto
Informations de sécurité liées au produit

Save these instructions
Guarde estas instrucciones
Sauvegarder ces instructions

SX6210_Manual_100810.indd 1 10/8/10 9:16:50 PM

To reduce the risk of injury, anyone using, repairing, maintaining, or
changing accessories on this tool must read and understand these
instructions before performing any of these tasks.

WARNING

Always inspect, operate, and maintain this tool in
accordance with American National Standards Institute
Safety Code of Portable Air Tools (ANSI B186.1) and any
other applicable safety codes and regulations.

These tools are rated at 90 psi / 6.2 bar max air
pressure for safety, top performance, and maximum
durability of parts; do not exceed this pressure while
the tool is running.

Always shut off air supply, drain hose of air pressure
and disconnect tool from air supply when not in use,
before changing accessories, or when making repairs.

Never direct air at yourself or anyone else.
Always wear impact-resistant eye and face protection

when operating or performing maintenance on this tool.
High sound levels can cause permanent hearing loss.

Always use hearing protection when using this tool as
recommended by your employer or OSHA regulation.

Do not wear jewelry or loose fitting clothes.
Do not use quick disconnect couplings at tool. See

operating instructions for proper set up.
Whipping hoses can cause serious injury. Always

carefully check for damaged or loose hoses and fittings
before operating this tool.

Never tamper with or remove cutting wheel guard.
Avoid direct contact with accessories during and after

use. Gloves should be worn to reduce the risk of cuts
or burns.

Never run the tool off of the work. The tool may run
too fast and cause the accessory to be thrown off of
the tool.

Slipping, tripping, and/or falling while operating air tools
can be a major cause of serious injury or death. Be
aware of your surroundings and any excess hose left on
the walking or working surface.

Pneumatic tools can cause vibration in use. Vibration,
repetitive motions or uncomfortable positions over
extended periods of time may be harmful to your hands
and arms. Discontinue use of tool if discomfort, tingling
feeling or pain occurs. Consult a physician before
resuming use if any of these symptoms occur.

Do not stretch or overreach while using this tool.
If tool appears to malfunction, remove from service

immediately and arrange for repair.
Never use tool if there is any chance of coming into

contact with line electricity.
Use only Sunex certified spare parts for any repair made

to tool. Repairs should only be performed by properly
trained persons.

Do not lock, tape or wire the tool valve in the "on/off"
position.

Do not allow the exhaust air to come in contact with hot
surfaces or flames.

Avoid inhaling dust or handling debris from the work
process, which can be harmful to your health. Use dust
extraction and wear respiratory protective equipment
when working with materials which produce airborne
particles.

Some dust created by power sanding, sawing, grinding,
drilling and other construction activities contains
chemicals known to the State of California to cause
cancer and birth defects or other reproductive harm.
Some examples of these chemicals are:

- Lead from lead based paints

- Crystalline silica bricks and cement and other
masonry products

- Arsenic and chromium from chemically-treated
lumber
Your risk from these exposures varies, depending on
how often you do this type of work. To reduce your
exposure to these chemicals: work in a well ventilated
area, and work with approved safety equipment, such
as those dust masks that are specially designed to filter
out microscopic particles.

Additional Safety Warnings

Do not modify this tool or its accessories.
Daily measure the air tool speed with tachometer to

make sure it is not greater than the RPM stated on the
cutting wheel accessory.

This tool is not recommended for use in explosive
atmospheres or underwater use.

Operators and maintenance personnel must be
physically able to handle the bulk, weight, and power
of this tool.

This tool is for professional use only.

SAFETY INSTRUCTIONS - DO NOT DISCARD - GIVE TO USER

SX6210: Parts Breakdown & Operating Manual 2 10/08/10

SX6210_Manual_100810.indd 2 10/8/10 9:16:51 PM

Instruction Manual

This tool is designed for cutting plastics, fiberglass, composites
and metals. No other use is permitted.

Air Supply Requirements

Tool is designed to operate at 90 psi (6.2 bar) at free speed
measured at the tool, of clean, dry air. Operating this tool at
higher pressures will drastically reduce the tool life and could
cause injury.

The air inlet thread on this tool is a standard 1/4" NPT.
Line pressure should be increased for any unusually long
air hose run (over 25 feet). Minimum hose diameter should
be 3/8" I.D. and all fittings should have the same inside
diameter. See diagram below for proper air supply setup.

Lubrication

Lubricate the tool each day after use with quality SAE #10
air motor oil. Add the oil to the air inlet or into the hose at the
nearest connection to the air supply, then run the tool until
all excess oil is expelled from the exhaust. Total oil quantity
needed for this procedure is approximately 1 ounce.

EC DECLARATION OF CONFORMITY

We, Sunex International Inc., 315 Hawkins Rd, Travelers Rest,
SC 29690, declare under our sole responsibility that the
product to which this declaration relates, is in conformity with
the requirements of the Council Directive of June 1998 on the
approximation of the laws of the Member States relating to
machinery. (EN792, 98/37/EC)

Harmonized Standards Applied:

EN 792-6

National Standards Applied:

ISO 8662-7, ISO 15744-2002
Machine Name:
SX6210 Reversible Cut-Off Tool
Serial No.:
TS010380000 or higher
Techical Data:
3" Cutting Wheel Std.
Air Pressure: 90 psi (6.2 bar)

Noise and Vibration Declaration

Tool produces a noise level (no load) of 87 dBA
sound pressure with 3 dBA uncertainty per
EN ISO15744-2002. Vibration level is 0.7 m/s2
tested per EN 28662-1 & EN28662-7:1997

Signature of Issuer:

Name and Position of Issuer: John Stratton, Product Manager
Sunex International Inc.
Date of Issue: October 15, 2010

Drain Daily

Regulator Oiler Quick Coupler Leader

Hose

Nipple

Do Not Install

Quick Coupling

Here

Nipple

Filter

Air Supply

Whip Hose

Specifications

Wheel Size .........................................................................3"

Free Speed ........................................................ 18,000 RPM

Motor Size .................................................................. 0.9 HP

Length .............................................................8.3" (211mm)

Weight .......................................................... 2 Lbs. (0.91 kg)

Avg. Air. Cons. ..........................................3.6 cfm (102 l/min)

Air Inlet ................................................................... 1/4" NPT

Min. Hose Size ............................................ 3/8" I.D. (10mm)

SX6210: Parts Breakdown & Operating Manual 3 10/08/10

SX6210_Manual_100810.indd 3 10/8/10 9:16:51 PM

REF. PART
NO. NO. DESCRIPTION QTY.

1 RS621001 Regulator 1
2 RS820R02 O-Ring (AS015) 1
3 RS246002 O-Ring (3.5 x 1.4) 1
4 RS621004 Valve Stem 1
5 RS288302 O-Ring (P10) 1
6 RS621006 Regulator 1
7 RS850XLR07 Air Inlet 1
8 RS621008 Muffler 1
10 RS621010 Protecting Rubber 1
11 RS621011 Pin (3 x 24L) 1
12 RS820R12 Lever 1
13 RS820R13 Spring 1
14 RS820R14 Valve 1
15 RS820R15 Washer (6 x 13.8 x 1.6T) 1
16 RS820R161A Pin (2.8 x 25.8L) 1
17 RS621017 Housing 1
18 RS21114 Bearing (626ZZ) 1
19 RS820R19 Washer (17 x 33.2 x 0.8T) 1
20 RS820R20 Rear Plate 1
22 RS820R22 Rotor Blade 4
23 RS820R23 Rotor 1
24 RS621024 Cylinder 1
25 RS820R25 Bearing Spacer 1
26 RS288323 Pin (2.5 x 6L) 2

REF. PART
NO. NO. DESCRIPTION QTY.

27 RS820R27 Front Plate 1
28 RS10920 Bearing (6000ZZ) 2
29 RS820R29 Washer (22 x 33.2 x 3T) 1
30 RS820R30 Disc Retainer 1
31 RS820R31 Clamp Nut 1
32 RS621032 Guard 1
33 RS621033 Nut 1
34 * 3" Disc Wheel 1
35 RS820R35 Washer (9.6 x 21 x 1.5T) 1
36 RS820R36 Nut 1
37 RS820R37 Screw 1
38 RS850XLR60 O-Ring (S16) 1
39 RS20639 Stop Spanner 19 mm 1
40 RS31539 Hex 1
41 RS103841 Stop Spanner 1
42 RS103740 Muffler Body 1
43 RS850XLR71 Washer 1
45 RS850XLR72 O-Ring (AS125) 1
46 RS850XLR73 O-Ring (S30) 1
47 RS850XLR77 Screw (M4 x 8) 1
48 RS850XLR78 Snap Ring (RTW-18) 1
49 RS850XLR79 Regulator 1

* Replacement Disc wheels available as: 87602 (Pack of 5).

REVERSIBLE
CUT-OFF TOOL

SX6210

7

3

4

5

6

11

12

13

14

15

17

20

26

22

23

24

25

26

27

28

29

30

31

32

39

18

19

36

37

35

33

28

40

41

10

42

1

2

38

49

47

48

16

8

45

46

43

34

SX6210: Parts Breakdown & Operating Manual 4 10/08/10

SX6210_Manual_100810.indd 4 10/8/10 9:16:51 PM