Sunex Tools SX246 User Manual [en, es, fr]
Operating Instructions • Warning Information • Parts Breakdown
Some dust created by power sanding, sawing, grinding, drilling, and other
construction activities contains chemicals known to cause cancer, birth
defects or other reproductive harm. Some examples of these chemicals are:
• lead from lead-based paints,
• crystalline silica from bricks and cement
and other masonry products, and
• arsenic and chromium from
chemically-treated lumber.
Your risk from these exposures varies, depending on how often you do this
type of work. To reduce your exposure to these chemicals: work in a well
ventilated area, and work with approved safety equipment, such as those
dust masks that are specially designed to filter out microscopic particles.
SPECIFICATIONS
Number of Needles ................. 19
Needle Diameter .................. 3mm
Rec. Air Pressure .............. 90 PSI
Air Consumption ............. 10 CFM
Blows Per Minute ......3,000 BPM
Air Inlet Thread ............. 1/4" NPT
Rec. Hose ID ......................... 3/8"
Sound Level ..................... 97dBA
Overall Length ........................11"
Weight ............................. 5.72 Lb.
ALWAYS READ
INSTRUCTIONS
BEFORE USING
POWER TOOLS
ALWAYS WEAR
SAFETY GOGGLES
WEAR HEARING
PROTECTION
AVOID PROLONGED
EXPOSURE TO
VIBRATION
SX246
Pistol
GriP
Needle
scaler
SX246: Parts Breakdown & Operating Manual 1 rev. 03/13/06
WARNING!
FAILURE TO OBSERVE THESE WARNINGS
COULD RESULT IN INJURY.
This Instruction Manual Contains
Important Safety Information.
READ THIS INSTRUCTION MANUAL
CAREFULLY AND UNDERSTAND ALL
INFORMATION BEFORE OPERATING
THIS TOOL.
• Always operate, inspect and maintain this
tool in accordance with American National
Standards Institute Safety Code of Portable
Air Tools (ANSI B186.1) and any other
applicable safety codes and regulations.
• For safety, top performance and maximum
durability of parts, operate this tool at 90
psig/6.2 bar max air pressure with 3/8"
diameter air supply hose.
• Always wear impact-resistant eye and face
protection when operating or performing
maintenance on this tool. Always wear
hearing protection when using this tool.
• High sound levels can cause permanent
hearing loss. Use hearing protection as
recommended by your employer or
OSHA regulation.
• Keep the tool in efficient operating
condition.
• Operators and maintenance personnel
must be physically able to handle the bulk,
weight and power of this tool.
• Air under pressure can cause severe injury.
Never direct air at yourself or others.
Always turn off the air supply, drain hose
of air pressure and detach tool from air
supply before installing, removing or
adjusting any accessory on this tool, or
before performing any maintenance on this
tool. Failure to do so could result in injury.
Whip hoses can cause serious injury.
Always check for damaged, frayed or loose
hoses and fittings, and replace
immediately. Do not use quick detach
couplings at tool. See instructions for
correct set-up.
• Place the tool on the work before starting
the tool. Do not point or indulge in any
horseplay with this tool.
• Slipping, tripping and/or falling while
operating air tools can be a major cause
of serious injury or death. Be aware of
excess hose left on the walking or
work surface.
• Keep body working stance balanced and
firm. Do not overreach when operating
the tool.
• Anticipate and be alert for sudden changes
in motion during start up and operation of
any power tool.
• Do not carry tool by the hose. Protect the
hose from sharp objects and heat.
• Tool shaft may continue to rotate briefly
after throttle is released. Avoid direct
contact with accessories during and after
use. Gloves will reduce the risk of cuts
or burns.
• Keep away from rotating end of tool.
Do not wear jewelry or loose clothing.
Secure long hair. Scalping can occur
if hair is not kept away from tool and
accessories. Choking can occur if
neckwear is not kept away from tool
and accessories.
• Do not lubricate tools with flammable or
volatile liquids such as kerosene, diesel
or jet fuel.
• Do not force tool beyond its rated capacity.
• Do not remove any labels. Replace any
damaged labels.
• Use accessories recommended by
Sunex Tools.
• Air powered tools can vibrate in use.
Vibration, repetitive motions or
uncomfortable positions over extended
periods of time may be harmful to your
hands and arms. Discontinue use of tool if
discomfort, tingling feeling or pain occurs
Seek medical advice before resuming use.
SX246: Parts Breakdown & Operating Manual 2 rev. 03/13/06
SX246
Pistol GriP
Needle scaler
Air Hammer
10
13
14
12
15
16
11
Ref. # Item # DESCRIPTION QTY
1 RS24601 Handle 1
1
2
8
18
9
7
6
5
4
2 RS24602 Trigger Pin 1
3 RS24603 Regulator Pin 1
4 RS24604 Hose Adapter 1
5 RS24605 Throttle Spring 1
6 RS24606 Valve Stem 1
3
7 RS24607 O-Ring 1
17
8 RS24608 Aluminum Trigger 1
9 RS24609 Steel Ball Seat 1
10 RS24610 Upper Valve Case 1
11 RS24611 Valve Disc 1
12 RS24612 Lower Valve Case 1
13 RS24613 Valve Pin 2
14 RS24614 Piston 1
15 RS24615 Cylinder 1
16
17 RS24617 O-Ring 1
18 RS24618 Regulator 1
* RS87301 Quick Change Retainer 1
Needle Scaler Attachment
25
24
23
19
20
21
22
26
27
19
* RS87301 Not included with tool; available
for purchase separately.
Ref. # Item # DESCRIPTION QTY
19 RS24619 Snap Ring 2
20 RS24620 Plunger 1
21 RS24621 Spring 1
22 RS24622 Needle Holder 1
23 RS24623 Needle 19
24 RS24624 Anvil 1
25 RS24625 Housing 1
26 RS24626 Hex Screw 3
27 RS24627 Adapter 1
SX246: Parts Breakdown & Operating Manual 3 rev. 03/13/06
Loading...