Sunbeam MRU2GKS-V000-12A44, BSV9GTS-R772-12A44 User Manual
P.N. 140450
IMPORTANT INSTRUCTIONS
DO NOT DESTROY
Warnings and Safeguards
As with all electrical products, misuse of product or failure to properly
follow the instructions may cause overheating, fire or personal injury.
Please read the product label and all of the instructions before using your
heated product.
1. Do not use this heated product with an infant, a child, an
incapacitated or immobile person, a paraplegic, a quadriplegic, a
diabetic, one insensitive to heat such as a person with poor blood
circulation, or anyone who cannot clearly understand the instructions
and/or operate the controls.
2. Do not route electrical cords between the mattress and box spring. Do
not allow the cords to be pinched.
3. Do not use with damaged cords. Damaged cords can lead to fire. Do
not tuck in, trap, fold, cross or pinch cords or controls between bed
slats, mattress or springs, or against walls, footboards or bed frame.
4. Do not dry clean this heated product. Cleaning liquid may damage
the insulation of the heating element. Improper laundering may cause
problems with the heating wire which can lead to fire.
5. Do not tuck in, pinch, flex or expose the heating wire to rubbing.
A damaged heating wire may result in possible overheating or fire. Do
not tuck or wrap the heated product, supply cord or control in a sofa
or other furniture. All portions of the heated product and controller
should be visible at all times.
6. Turn off or unplug the control for the heated product when not using.
7. Wrapping the cord around the controller may damage the cord.
Loop loosely when storing.
8 Controller is not waterproof. Do not immerse in water.
9. Keep the control away from drafty areas that may become damp or wet
such as an open window.
10. Do not use pins; they may damage the electric wiring.
11.
Be sure this blanket/mattress pad/throw is used only on an AC supply
current circuit of 110-120 volts. Do not use with an extension cord.
IMPORTANT INSTRUCTIONS
DO NOT DESTROY
12.
The product
product is bunched or folded while in use.
13. Keep all dogs, cats and other pets away from this heated product.
This is an electrical appliance that they can damage or be injured by.
14. Do not use blanket/mattress pad on a waterbed, sofa, bunk bed or
mechanically adjustable bed and do not use throw on a waterbed,
bunk bed or mechanically adjustable bed.
15. For throw blankets: Do not use with rocking chairs, recliners, chairs
with casters or wheels, or other furniture subject to movement. Do not
wrap product around control.
16. Do not use another electronic heating device in conjunction with your
heated product.
17. Use the proper size blanket/mattress pad for your bed. For example,
use a Twin Size warming blanket on a Twin Size bed.
18. If the following Important Instructions are not followed, the heated
product will not operate properly.
19. Not for hotel, motel or other institutional use.
20. If you see the heated product operating improperly, unplug it
immediately and call Sunbeam Consumer Care in the U.S at
800-892-7684 or in Canada at 800-667-8623.
may experience increased heat in areas where heated
Welcome
Thank you for choosing a Sunbeam® heated product. With your purchase you’ve
made a real investment in your comfort and can look forward to staying warm and
cozy for many cool days to come.
With over 50 years of experience and over 25 million households using a
Sunbeam
Sunbeam® brand for quality and performance.
So get ready for a more restful sleep.
®
heated product, rest comfortably knowing that you can trust the
Table of Contents
Control Chart .................................................................................................................. 1
Auto-Off and Preheat Features .............................................................................................. 1
Heated Blanket and Mattress Pad
Setup ................................................................................................................................. 2
Control Features ............................................................................................................. 3-4
Warming Throw
Setup ................................................................................................................................. 5
Control Features ................................................................................................................ 5
Care and Cleaning ................................................................................................................. 6
Frequently Asked Questions ................................................................................................ 7-8
Warranty................................................................................................................................. 9
How to Obtain Warranty Service ........................................................................................... 10
DO NOT RETURN THIS PRODUCT TO THE PLACE OF PURCHASE.
If you have any questions while setting up or using your product,
please visit us on the World Wide Web at: www.sunbeam.com or
contact Sunbeam Consumer Care in the U.S. at (800) 892-7684
or in Canada at (800) 667-8623.
Control Chart
SelectTouch™ SmartSense™ ComfortSet™ ChoicePlus™ StyleSmart™ SimpliTouch™ EasySet™ Pro EasySet™ EliteStyle™ PrimeStyle™ PrimeStyle
S85KQ/
S85KQA
10 hour*
(S85A,
S85KQA)*
J85PA
J85P/
J85D
J85KQAJ/
5KQP/
J85KQD
10 hour*
(J85PA,
J85KQAJ)*
N85AP
M85AP
Throw
Throw
3 hour 3 hour
M85P
Throw
Style #
(Single Control)
Style #
(Dual Control)
Backlit Display
Ambient Temperature
Compensation
Auto-Off Select 10 hour 10 hour 10 hour 10 hour 10 hour
Warming Settings 10 10 10 20 10 10 10 10 3 3 3
Graduated
Temperature Settings
Silent Operation
Preheat
Easy Operation
Ergonomic Temperature
Adjustment
Easy Grip
Interchangable Top
Auto Dimmer
P85 G85 O85 85P H85 K85P S85/S85A
P85KQ G85KQ O85KQ 85KQP H85KQ K85KQP
b b b b b
b b
b b
b b b b b b b b b b b
b b b b
b b b b b b b b b b b
b b
b b b b b b b b b
b
b b b b b
Auto-Off & Preheat Features
Auto-Off Feature (selected models only):
The “Auto-Off” feature is designed for conservation of energy by automatically turning
your blanket or mattress pad off after 10 hours of continuous use (3 hours for throws).
For Dual Controls:
Each control operates independently and will turn off 10 hours after the control is turned “On”.
Auto-Off Select* Feature (selected models only):
Some models with the “Auto-Off” feature (see control chart) offer an “Auto-Off Select” button that can disable
the “Auto-Off” feature so the heated product will not automatically turn off.
Controls with the “Auto-Off Select” feature have the “Auto-Off” active as the default so the heated product
will automatically turn off after 10 hours.
To disable the “Auto-Off”, press the “Auto-Off Select” button. The word “StayOn” will appear in the digital display
to indicate the “Auto-Off” feature is deactivated and the heated product will NOT automatically turn off after 10 hours.
The heated product will remain on until the product is manually turned off by pressing the “On/Off” button.
To activate auto-off, press the “Auto-Off Select” button. The word “AutoOff” will appear in the digital display to
indicate the “Auto-Off” feature is activated and the heated product will automatically turn off after 10 hours.
Note: After a power outage, the “Auto-Off” feature automatically resets the timer.
To restart all heated products after a power failure:
Press the power button and the heated product will begin to warm.
Preheat Feature (selected models only):
The preheat function will heat the bed for a period of 30 minutes and the control will return to its original setting.
1 To use the preheat feature, simply turn on the warming product by pressing the “On/Off” button and then press the
“Preheat” button. The display will show “PH” while the function is activated.
2 To reset the preheat feature, simply turn off the control by pressing the “On/Off button and then turn it back on by
pressing the “On/Off” button.
For questions or support, please visit: www.sunbeam.com
1
™
AO
*only
For questions or support, please visit: www.sunbeam.com
1
run cord
under the bed
Mattress Pad
Cord Connector
Secondary
Control
Primary
Control
Flag Ta g
Label
Power
Cord
Module
Left Side
Right Side
Heated Blanket and Mattress Pad Setup
run cord
under the bed
Blanket Cord Connector
Primary
Control
Flag Ta g
Label
Power
Cord
Module
Left Side
Right Side
1 Place the heated blanket/mattress pad on the bed with the label at the foot of the
bed facing upward.
2 Connect the cord into the module at the bottom of the heated blanket/
mattress pad until the plastic hinges click into place.
CAUTION: Cord must be COMPLETELY CONNECTED. A risk of fire could
result from a loose connection.
3 Run the control cord on the floor under the bed. Do not sandwich cord between the
mattress and box spring. Avoid any tangling or pinching.
4 Control Placement:
• Dual Control for heated blanket or mattress pad –
place primary control (label on back of control)
on the right side of the bed.
2
1
3
• Single Control for heated blanket or mattress pad –
the control can be placed on either side of the bed.
2
5
5
(Label on back
of control)
4
2
5 Plug power cord into a 110-120 volt wall outlet.
CAUTION: Do not use with generator power.
IMPORTANT
CAUTION: Do not plug main power cord into the wall outlet until you have completely set up
your heated product per the instructions.
• Disconnect power cord from wall before detaching control from heated product.
• Always make sure cords and controls are NOT trapped or pinched between bed slats, mattress, springs,
against wall, foot board or bed frame, or between furniture, walls or chairs.
is wider than the other). To reduce the risk of electrical shock, this plug is intended to fit only one way into
CAUTION: Do not attempt to force the plug. This appliance has a polarized plug (one blade
an outlet. If the plug does not fit in the outlet, reverse the plug. If it still does not fit, contact a qualified
electrician. Do not attempt to defeat this safety feature.
2
1
3
For questions or support, please visit: www.sunbeam.com
4
(Label on back
of control)
See Control Features on page 4
for your individual control.
If there is a flashing light or
your control displays a flashing
“FF”, “F1” or “F2” see page 8.
Control Features
™
SelectTouch
P85
(Single Control)
P85KQ
(Dual Control)
SmartSense
G85
(Single Control)
G85KQ
(Dual Control)
• DIGITAL CONTROL – with backlit LCD for nighttime viewing
• AMBIENT TEMPERATURE COMPENSATION – adapts to room temperature changes for consistent
warmth
• SELECTABLE AUTO-OFF – activate or deactivate the 10 hour independent auto-off (see page 1)
• 10 GRADUATED TEMPERATURE SETTINGS – with finer temperature adjustment at lower settings
• ERGONOMIC TEMPERATURE ADJUSTMENT – large embossed silicone push buttons to maximize operator
comfort
• SILENT OPERATION – no clicking when adjusting the temperature
• PREHEAT – for cozy warmth before bedtime (see page 1)
• SOLID STATE – for accurate and consistent heat control
• EASY OPERATION – electronic digital control for easy operation
™
• INTERCHANGEABLE COVERPLATES – two colors included
• DIGITAL CONTROL – with backlit LCD for nighttime viewing
• AMBIENT TEMPERATURE COMPENSATION – adapts to room temperature changes for consistent
warmth
• AUTO-OFF – 10 hour independent auto-off (see page 1)
• 10 TEMPERATURE SETTINGS – select your personal comfort level
• SILENT OPERATION – no clicking when adjusting the temperature
• PREHEAT – for cozy warmth before bedtime (see page 1)
• SOLID STATE – for accurate and consistent heat control
• EASY OPERATION – electronic digital control for easy operation
• EASY GRIP– ergonomic control for easy operation
ComfortSet
O85
(Single Control)
O85KQ
(Dual Control)
ChoicePlus
85P
(Single Control)
85KQP
(Dual Control)
™
• DIGITAL CONTROL – with backlit LCD for nighttime viewing
• AUTO-OFF – 10 hour independent auto-off (see page 1)
• 10 GRADUATED TEMPERATURE SETTINGS – with finer temperature adjustment at lower settings
• ERGONOMIC TEMPERATURE ADJUSTMENT – large embossed push buttons to maximize operator
comfort
• SILENT OPERATION – no clicking when adjusting the temperature
• PREHEAT – for cozy warmth before bedtime (see page 1)
• SOLID STATE – for accurate and consistent heat control
• EASY OPERATION – electronic digital control for easy operation
™
• DIGITAL CONTROL – with backlit LCD for nighttime viewing
• AUTO-OFF – 10 hour independent auto-off (see page 1)
• 20 TEMPERATURE SETTINGS – select your personal comfort level
• SILENT OPERATION – no clicking when adjusting the temperature
• PREHEAT – for cozy warmth before bedtime (see page 1)
• SOLID STATE – for accurate and consistent heat control
• EASY OPERATION – electronic digital control for easy operation
• EASY GRIP – ergonomic control for easy operation
(continued on page 4)
For questions or support, please visit: www.sunbeam.com
3
Control Features
ON
OFF
(continued from page 3)
StyleSmart
H85
(Single Control)
H85KQ
(Dual Control)
SimpliTouch
K85P
(Single Control)
K85KQP
(Dual Control)
™
• DIGITAL CONTROL – with backlit LCD for nighttime viewing
• AUTO-OFF – 10 hour independent auto-off (see page 1)
• 10 TEMPERATURE SETTINGS – select your personal comfort level
• SILENT OPERATION – no clicking when adjusting the temperature
• SOLID STATE – for accurate and consistent heat control
• EASY OPERATION – electronic digital control for easy operation
• EASY GRIP – ergonomic control for easy operation
™
• BACKLIT DIAL – for easy nighttime viewing of the warming setting
• AUTO-OFF– 10 hour independent auto-off (see page 1)
• 10 TEMPERATURE SETTINGS – select your personal comfort level
• SOLID STATE – for accurate and consistent heat control
• EASY GRIP – ergonomic control for easy operation
• AUTO DIMMER – the lighted dial will automatically dim after 60 seconds
EasySet™ Pro
• BACKLIT DIAL – for easy nighttime viewing of the warming setting
• AUTO-OFF– 10 hour independent auto-off (see page 1) (Style #s S85A & S85QA only)
• 10 TEMPERATURE SETTINGS – select your personal comfort level
• SOLID STATE – for accurate and consistent heat control
• EASY GRIP – ergonomic control for easy operation
S85/S85A
(Single Control)
S85KQ/S85KQA
(Dual Control)
EasySet
™
• AUTO DIMMER – the lighted dial will automatically dim after 60 seconds
• BACKLIT DIAL – for easy nighttime viewing of the warming setting
• AUTO-OFF – 10 hour independent auto-off (see page 1) (Style #s J85PA & J85QPA only)
• 10 TEMPERATURE SETTINGS – select your personal comfort level
• SOLID STATE– for accurate and consistent heat control
• EASY GRIP – ergonomic control for easy operation
J85P/J85D/J85PA
(Single Control)
J85KQP/J85KQD/J85KQPA
(Dual Control)
• AUTO DIMMER– the lighted dial will automatically dim after 60 seconds
Using Your Control:
1 To turn the control on, press the “On/Off” button.
Note: For SelectTouch™, SmartSense™, ComfortSet™, ChoicePlus™ and StyleSmart™ controls, the backlit display light will
reset itself by flashing “88” and then will return to the previous setting and will begin to warm.
2 Adjust the warming setting to your personal comfort by rotating the top knob left or right for SmartSense
StyleSmart™, SimpliTouch™, EasySet™ controls.
3 Note: For SelectTouch
™
and ComfortSet™ controls, press the large left button with the “-” sign to lower the heat setting and
the large right button with the “+” sign to increase your heat setting.
4 To turn the heated blanket/mattress pad OFF, press the “On/Off” button.
CAUTION: ALWAYS turn the heated blanket/mattress pad “OFF” when not in use.
™
, ChoicePlus
™
,
4
For questions or support, please visit: www.sunbeam.com
Warming Throw Setup
Module
Control
Power
Cord
Flag T a g
Throw Cord
Connector
Throw Cord
Label
Module
Control
Power
Cord
Flag T a g
Throw Cord
Connector
Throw Cord
Label
When setting up your warming throw, be sure to follow the steps below in order.
1 Locate the warming throw’s information label near the module.
2 Connect the cord into the module at the bottom of the warming throw until
the plastic hinges click into place.
CAUTION: Cord must be COMPLETELY CONNECTED. A risk of fire could result
from a loose connection.
2
3
3
If there is a flashing light on
your control, see page 8.
1
2
2
1
3 Plug the [warming throw] power cord into a 110-120 volt wall outlet.
IMPORTANT
CAUTION: Do not plug main power cord into the wall outlet until you have completely set up
your heated product per the instructions.
• Disconnect power cord from wall before detaching control from heated product.
• Always make sure cords and controls are NOT trapped or pinched between bed slats, mattress, springs,
against wall, foot board or bed frame, or between furniture, walls or chairs.
• Do not wrap control in throw when in use.
• Do not use with generator power.
CAUTION: Do not attempt to force the plug. This appliance has a polarized plug (one blade is wider than the
other). To reduce the risk of electrical shock, this plug is intended to fit only one way into an outlet.
If the plug does not fit in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician.
Do not attempt to defeat this safety feature.
Control Features
PrimeStyle
M85P
Non Auto-Off
PrimeStyle
M85AP
Auto-Off
EliteStyle™
N85AP
Auto-Off
™
™
AO
For questions or support, please visit: www.sunbeam.com
Using Your Warming Throw Control:
1 To turn on the throw press the button in the middle of the control.
The indicator light will glow, depending on which setting the warming throw
is set, and the warming throw will begin to warm.
CAUTION: ALWAYS turn the warming throw “OFF” and disconnect the
power cord from the outlet when not in use.
2 To turn the warming throw OFF press the button through the different
settings until the temperature setting lights are not glowing.
Features:
• 3 TEMPERATURE SETTINGS – select your personal comfort level
• SILENT OPERATION – no clicking when adjusting the temperature
• SOLID STATE – for accurate and consistent heat control
• EASY OPERATION – electronic control for easy operation
• EASY GRIP – ergonomic control for easy operation
• AUTO-OFF (Selected models only) – 3 hour Auto-Off operation
(see page 1)
5
Loading...