Sunbeam LC7600 User Manual

Oskar

™

Professional

Direct drive food processor

Instruction Booklet

LC7600

Please read these instructions carefully and retain for future reference.

ContentsContents

Important instructions – retain for future use.

Sunbeam’s Safety Precautions 4

Features of Your Sunbeam Oskar™ Professional 6

Attachments for your Sunbeam Oskar™ Professional 8

Using your Sunbeam Oskar™

Professional 9

Fitting/using the tools on your Oskar™ Professional 11

Storing your Sunbeam Oskar™ Professional 13

Handy hints for Processing 15

Care and cleaning 17

Recipes 18

Sunbeam are very safety conscious when

designing and manufacturing consumer products, but it is essential that the product user also exercise care when using an electrical appliance. Listed below are precautions which are essential for the safe use of an electrical appliance:

• Read carefully and save all the instructions provided with an appliance.

• Always turn the power off at the power outlet before you insert or remove a plug. Remove by grasping the plug - do not pull on the cord.

• Turn the power off and remove the plug when the appliance is not in use and before cleaning.

• Do not use your appliance with an extension cord unless this cord has been checked and tested by a qualified technician or service person.

• Always use your appliance from a power outlet of the voltage (A.C. only) marked on the appliance.

• Close supervision is necessary when your appliance is being used near children or infirm persons.

• Never leave an appliance unattended while in use.

• Young children should be supervised to ensure that they do not play with the appliance.

• Do not use an appliance for any purpose other than its intended use.

• Do not place an appliance on or near a hot gas flame, electric element or on a heated oven. Do not place on top of any other appliance.

• Do not let the power cord of an appliance hang over the edge of a table or bench top or touch any hot surface.

• For safety reasons and to avoid maintenance by unskilled persons, some appliances are ‘sealed’ using tamperproof screws. Such appliances should always be returned to the nearest Sunbeam Appointed Service Centre for adjustment or repair if required.

• Do not operate any electrical appliance with a damaged cord or after the appliance has been dropped or damaged in any manner. If damage is suspected, return the appliance to the nearest Sunbeam Appointed Service Centre for examination, repair or adjustment.

• For additional protection, Sunbeam recommend the use of a residual current device (RCD) with a tripping current not exceeding 30mA in the electrical circuit supplying power to your appliances.

• Do not immerse the appliance in water or any other liquid unless recommended.

Sunbeam’s Safety Precautions

If you have any concerns regarding the performance and use of your appliance,

please visit www.sunbeam.com.au or contact the Sunbeam Consumer Service Line.

Ensure the above safety precautions are understood.

SAFETY PRECAUTIONS FOR YOUR

SUNBEAM FOOD PROCESSOR.

• Always use extreme care when handling processing blades and cutting discs. These are extremely sharp and may cause injury if handled incorrectly. Always store processing blades and cutting discs in their respective covers or processing containers.

• Unplug from power outlet when not in use, before putting on or taking off attachments, and before cleaning.

• Do not put hot liquids into the food processor bowl or blender. Warm liquids only.

• Avoid contacting moving parts at all times.

• Place the processor bowl onto the base of the processor before fitting any attachments.

• All blades and attachments should be removed with care before cleaning.

• Do not over fill the processor.

• Do not process for longer than the time periods recommended in the operating chart.

• Always remove the blade before emptying the processor bowl of its contents.

• Do not operate for more than 4 minutes at a time when processing heavy loads. None of the recipes in this manual are considered a heavy load.

Important instructions – retain for future use.

Sunbeam’s Safety Precautions

If you have any concerns regarding the performance and use of your appliance,

please visit www.sunbeam.com.au or contact the Sunbeam Consumer Service Line.

Ensure the above safety precautions are understood.

Features of Your Sunbeam Oskar™ Professional

Processing cover

The processing cover activates the automatic safety system. The Oskar™ Professional will not operate unless the cover is correctly positioned on the processing bowl and locked into place.

900 watt induction motor

The base houses a powerful 900 watt motor, which provides great processing results every time. Ideal for high load applications during processing. It provides greater starting strength and maintains a constant speed throughout. Its reliable, long life and quiet performance is backed by a 5 year guarantee.

On / off button

For easy use the large ON / OFF button starts and stops the operation of the food processor.

Pulse

The control panel includes a Pulse feature for optimum cutting precision during processing.

Storage drawer

Unique drawer design enables attachments to be stored conveniently within the appliance when not in use.

Food pusher

Guides food evenly down the feed tube and can also be used to close the chute while processing to prevent food from escaping through the feed tube.

Feed tube

The feed tube is used to guide ingredients down into the selected blades and allows you to add ingredients during other processing tasks.

Spindle

Drives all the food processing attachments. The spindle must be in place to operate the food processor.

Processing bowl

The water proof processing bowl achieves a large 2 litre working capacity due to the water seal around the base of the drive shaft and the lip of the lid.

Cord storage facility

For added convenience the unused cord length can easily be pushed into the base of the processor for storage.

Non-slip feet

Keeps the food processor secure on the bench top during use.

1. Processing blade

Stainless steel smooth edged processing blade is designed for cutting, kneading, whisking and emulsifying.

2. Variable slicing blade

The variable stainless steel slicing blade allows foods to be sliced to a variety of thicknesses, from 0mm - 7mm.

3. Reversible shredding disc - fine and coarse

Ideal control, the reversible stainless steel shredding blades allow for the choice of fine or coarse results.

4. Reversible grating and shaving disc

Unique to processing is the shaving blade. It does lovely thin flakes, great for parmesan and sweet potato crisps. The other side will achieve finely grated results, ideal for hard cheeses and chocolate.

5. Spatula

The spatula is ideal for assisting with all food processing tasks.

Attachments for your Sunbeam Oskar

™

Professional

Before using your Oskar™ Professional

• Wash the processing bowl, cover and all attachments in warm water using a mild detergent. Dry each part thoroughly before use.

• Before you assemble the food processor, ensure that the power cord is unplugged.

1. Place the motor base facing you on a dry, level surface.

2. Place the processing bowl onto the motor base, the bowl will only sit correctly on the base when the handle is positioned to the right, see figure 1.

3. Rotate the handle clockwise to lock, as indicated by the graphics on the left side of the motorbase, see figure 2.

Position the lid onto the processing bowl

. You will notice a solid grey arrow ▼ to the left of the holding lip on the lid, when placing the lid onto the bowl this arrow needs to align with the solid grey arrow ▲ on the handle of the bowl. To lock, turn the lid clockwise, as indicated by the graphics, on the top of the handle, see figure 3.



Using your Sunbeam Oskar

™

Professional

Fig 1

Fig 2

Fig 3

Important: If the processing bowl and cover are not correctly assembled, the Oskar™ Professional will not function.

Using your Oskar™ Professional

1. Plug the power cord into a 230-240V AC power outlet and turn the power ‘ON’.

2. Using the On/Off button on the control panel, press once to start processing.

The Pulse function remains on as long as the Pulse button is pressed down.

Further ingredients can also be added whilst processing by pouring through the feed tube once the food pusher has been removed.

3. After you have completed processing, press the On/Off button to stop processing.

Note: For maximum control when using your food processor, before turning on your food processor load the feed tube. Always use the food pusher for more evenly processed foods and never use your fingers.

Important: The Oskar™ Professional is fitted with a safety thermal cut-out device and will shut off in the event of overload. If this occurs, switch the appliance off and it will automatically reset when cool.

Using your Sunbeam Oskar™ Professional continued

Note: All attachments must be firmly attached to the spindle. Always adjust the attachments until you are sure that they are correctly fitted.

Placing the spindle

1. Fit the spindle onto the drive shaft, see figure 4.

Processing Blade

1. Fit the processor bowl and spindle as detailed previously in figures 1, 2 & 4.

2. Remove the processing blade from the storage drawer.

3. Fit the processing blade over the spindle and press firmly into place, see figure 5.

Warning: Use caution, as blades are sharp. Always handle the processing blade by its central plastic section.

4. Place food into the processing bowl.

5. Fit the processing cover to the processing bowl, see figure 3 and place the food pusher in the feed tube.

6. Plug the power cord into a 230-240V AC power outlet and turn the power ‘ON’.

7. Start processing using the On/Off or Pulse buttons.

8. When processing is complete, remove the spindle and blade from the processing bowl before removing the processed food.

Fitting/using the tools on your Oskar

™

Professional

Fig 4

Fig 5

Reversible grating, shaving and shredding blades

1. Fit the processor bowl and spindle as detailed previously, in figures 1, 2 and 4.

2. Select the 'Reversible' disc of your choice

- Shredding (fine or coarse), Grating or Shaving.

3. Fit the disc over the spindle and press firmly into place, see figure 6.

Warning: Use caution as the blades are sharp.

4. Fit the processing cover to the processing bowl as previously shown in figure 3 and place the food pusher in the feed tube.

5. Plug the power cord into a 230-240V AC power outlet and turn the power ‘ON’.

6. Start processing using the On/Off button.

7. When processing is complete, remove the disc and spindle from the processing bowl before removing the processed food.

Variable slicing blades

1. Fit the processor bowl and spindle as detailed previously in figures 1, 2 and 4.

2. Fit the slicing disc over the spindle and press firmly into place, see figure 7.

Warning: Use caution as the blades are sharp.

3. Fit the processing cover to the processing bowl as previously shown in figure 3 and place the food pusher in the feed tube.

4. Plug the power cord into 230-240V AC power outlet and turn the power 'ON'.

5. Start processing using the On/Off button.

6. When processing is complete, remove the disc and spindle from the processing bowl before removing the processed food.

Fitting/using the tools on your Oskar™ Professional continued

Fig 7

Fig 6

+ 23 hidden pages