Sunbeam’s Safety Precautions 1
Features of your Aspire Kettle 2
Using your Aspire Kettle 4
Sunbeam’s 3-Way Safety System 5
Care and Cleaning 6
Important instructions –
retain for future use.
Sunbeam’s Safety Precautions
SAFETY PRECAUTIONS FOR YOUR SUNBEAM
KETTLE.
• Always operate the kettle on a flat, level
surface.
• Boiling water will scald. Do not leave a boiling
or hot kettle near or where children
may touch it.
• Do not leave the power cord near the edge of a
bench top where children may touch or pull it.
Sunbeam is very safety conscious when
designing and manufacturing consumer products,
but it is essential that the product user also exercise
care when using an electrical appliance. Listed
below are precautions which are essential for the
safe use of an electrical appliance:
• Read carefully and save all the instructions
provided with an appliance.
• Always turn the power off at the power outlet
before you insert or remove a plug. Remove by
grasping the plug - do not pull on the cord.
• Turn the power off and remove the plug when the
appliance is not in use and before cleaning.
• Do not use your appliance with an extension cord
unless this cord has been checked and tested by
a qualified technician or service person.
• Always use your appliance from a power outlet of
the voltage (A.C. only) marked on the appliance.
• This appliance is not intended for use by persons
(including children) with reduced physical,
sensory or mental capabilities, or lack of
experience and knowledge, unless they have been
given supervision or instruction concerning use
of the appliance by a person responsible for their
safety.
• Children should be supervised to ensure that they
do not play with the appliance.
• The temperature of accessible surfaces may be
high when the appliance is operating. Even after
use, the heating element surface may be subject
to residual heat.
• Never leave an appliance unattended while
in use.
• Boiling water may be ejected, if overfilled.
• Do not open lid while water is boiling.
• Do not operate the kettle without water.
• Always turn the power off and unplug the cord
while the kettle is NOT in use.
• Your Aspire Kettle must only be used with the
power base supplied.
• Do not move kettle while switched on.
• Avoid spillage on the connector.
• Do not use an appliance for any purpose other
than its intended use.
• Any misuse of this product may lead to potential
injury.
• Do not place an appliance on or near a hot gas
flame, electric element or on a heated oven.
• Do not place on top of any other appliance.
• Do not let the power cord of an appliance hang
over the edge of a table or bench top or touch
any hot surface.
• Do not operate any electrical appliance with a
damaged cord or after the appliance has been
damaged in any manner. If damage is suspected,
return the appliance to the nearest Sunbeam
Appointed Service Centre for examination, repair
or adjustment.
• For additional protection, Sunbeam recommend
the use of a residual current device (RCD)
with a tripping current not exceeding 30mA in
the electrical circuit supplying power to your
appliances.
• Do not immerse the appliance in water or any
other liquid unless recommended.
• Appliances are not intended to be operated by
means of an external timer or separate remote
control system.
• This appliance is intended to be used in
household and similar applications such as: staff
kitchen areas in shops, offices and other working
environments; farm houses; by clients in hotels,
motels and other residential type environments;
bed and breakfast type environments.
If you have any concerns regarding the performance and use of your appliance,
please visit www.sunbeam.com.au or contact the Sunbeam Consumer Service Line.
Ensure the above safety precautions are understood.
1
Features of your Aspire Kettle
1.7L brushed stainless steel design
7 cup capacity kettle constructed using long
life stainless steel.
2400 watt concealed element
The fast boil 2400 watt element is concealed
in the base of the kettle for longer element
life.
360 degree cordless power base
Designed to allow you to place the kettle
on the base in any direction.
Removable mesh filter
Keeps the water clean of any foreign matter
and is removable or easy cleaning.
2
3-Way Safety System.
1 – Automatically switches the kettle off after boiling.
2 – Cuts out for boil-dry production.
3 – Shuts down in case of overheating.
Hinged locking lid
Opens at the push of a button for one-handed
use and easy filling at the tap.
Twin water level gauges
Full length water gauge indicates the volume
of water in the kettle up to 1.7L. The two
gauges make the kettle convenient to use for
both left and right handed users.
On/Off switch with auto cut-off
Switches the kettle off automatically after
boiling.
Cord storage facility
Excess cord can be wound around the cord
storage facility underneath the power base.
3
Using your Aspire Kettle
Before using your kettle.
It is recommended that you clean your kettle
before use by filling the kettle with water, up
to the maximum level indicator, boil and
discard.
Using your kettle.
1. To fill the kettle, remove it from the power
base and lift the lid, by pressing the button
on the handle. Alternatively, the kettle may
be filled through the pouring spout.
2. Fill the kettle with the desired amount of
water. Always fill the kettle between the
minimum and maximum marks. Too little
water will result in the kettle switching off
before the water has boiled.
NOTE: Do not fill the kettle over the maximum
level, as water may spill out of the spout
when boiling.
3. Push the lid closed firmly until it locks into
position.
4. Place the kettle on the power base and
connect the plug into a 230/240 Volt AC
power outlet. Turn the power ON.
5. Press the ON/OFF button downwards at the
base of the kettle. The boiling indicators
beneath the water gauges will illuminate to
indicate the kettle is heating. The kettle
will switch off automatically once the water
has boiled.
NOTE: Ensure that the ON/OFF switch is clear
of obstructions and the lid is firmly closed.
The kettle will not turn off if the ON/OFF
switch is constrained or if the lid is left open.
Do not remove the kettle from the power base
while water is heating.
6. Lift the kettle from the power base and
pour the water.
NOTE: Use caution when pouring the water
from your kettle, as boiling water will scald.
7. The kettle may be stored on the power
base while not in use. The kettle will not
re-boil until the ON/OFF switch is pressed
downward.
NOTE: Ensure the power is turned off at the
power outlet when the kettle is not in use.
Should you accidentally allow the kettle to
operate without water, boil-dry protection will
automatically switch it off. If this occurs,
allow the kettle to cool before filling with
cold water and re-boiling.
Cord Storage Facility.
Excess cord can be stored by winding the
cord around the storage facility underneath
the power base.
360° power base
4
Sunbeam’s 3-Way
Safety System
Safety is a major consideration in the
design of a Sunbeam kettle. This is why we
have developed our 3-Way Safety System,
which ensures that your kettle will:
1. Automatically switch off after boiling.
For convenience, safety and energy
efficiency, your Sunbeam kettle will
automatically switch off after boiling.
2. Cut-out for boil-dry protection.
If the kettle is operated without water, it
will automatically cut-out, preventing any
damage to the element.
If this occurs, allow the kettle to cool
before filling with cold water and
re-boiling.
3. Shut-down in case of overheating.
In the event of overheating, the kettle will
automatically shut down to prevent further
damage. Should this occur, take your kettle
to a Sunbeam Service Centre or Appointed
Service Agent.
The Aspire Kettle features the Sunbeam Quiet
Shield which is new and exclusive quiet boil
technology designed to make boiling water a
peaceful practice.
The Sunbeam Quiet Shield
steel disk attached to the kettle floor which
acts as a diffuser plate. It is perforated with
a range of holes which help disperse, and
reduce the size of, the water bubbles thus
significantly reducing the noise of the boiling
process.
Maintaining the Quiet Boil Technology.
Mineral deposits in tap water solidify when
the water is heated; lime scale may be white,
coloured, even rusty-looking and is normally
visible but phosphate scale isn’t generally
visible although may cause the water to
appear cloudy when heated.
Regular use of the kettle can lead to the
build-up of these minerals which reduces the
effectiveness of the Sunbeam Quiet Shield
as well as the performance of the kettle.
It is important to descale your kettle regularly
to maintain the Quiet Shield
the life of the kettle.
Sunbeam recommend that the kettle is
descaled every 4-6 weeks. Go to page 6 for
more information on how to descale your
Aspire Kettle.
®
is a stainless
®
and to prolong
®
5
Care and Cleaning
Always disconnect the kettle from the power
outlet before cleaning.
Never immerse the kettle switch area, cord or
power base in water, or allow moisture to
come into contact with these parts.
Descale Your Kettle Regularly.
Mineral deposits in tap water solidify when
the water is heated; lime scale may be white,
coloured, even rusty-looking and is normally
visible but phosphate scale isn’t generally
visible although may cause the water to
appear cloudy when heated. This may cause
the interior of the water gauge to discolour,
reduce the effectiveness of the Quiet Boil
technology, cause overheating, trigger the
boil-dry cut-out mechanism or even reduce
the kettle’s life.
Even in soft water areas it is important to
descale your kettle regularly to help
maintains its lifecycle.
NOTE: Failure to descale products regularly
can be deemed as negligent handling and
any faults caused by mineral build up will
not be covered by the Sunbeam 12 Month
Guarantee.
To remove this build-up, use Sunbeam Liquid
Descaler, a simple to use, non-toxic cleaner
available from Sunbeam Appointed Service
Agents.
To clean the stainless exterior
The stainless steel surface may be wiped over
with a damp cloth and polished with a soft
dry cloth.
CAUTION: Do not use chemicals, steelwool, or
abrasive cleaners to clean the outside of the
kettle, as these will scratch the stainless
steel surface.
To clean the mesh filter.
Press the button on the handle to open the
hinged lid. Grasp the top of the mesh filter
and pull upwards to remove. Wash in warm
soapy water and dry thoroughly before
replacing in the kettle.
Cleaning the concealed heating element
This kettle features a non-corrosive stainless
steel heating element. Over time, scale may
build up on the concealed element inside the
kettle, causing discolouration that may have
the appearance of rust. Be assured this is not
rust. If this occurs clean with a green
Scotchbrite
abrasive cleaning cream. Rinse and clean
thoroughly with tap water before using your
kettle again.
®
scourer or similar and a suitable
Alternatively:
1. Fill the kettle with 3 cups of white vinegar
and the remainder with water and allow to
stand overnight. DO NOT BOIL.
2. Empty the solution from the kettle. Any
stains remaining inside the spout can be
removed by rubbing with a damp cloth. Fill
the kettle with clean water, bring to boil
and then discard the water. Repeat and the
kettle will then be ready to use.
6
Notes
Notes
12
Month
Replacement
Guarantee
This Sunbeam product is covered by a
12 month replacement or repair warranty,
which is in addition to your rights under the
Australian Consumer Law (if your product
was purchased in Australia) or New Zealand
Consumer Guarantees Act (if your product
was purchased in New Zealand).
Should you experience any
difficulties with your product
during the warranty period,
please contact our customer
service line for advice on 1300
881 861 in Australia, or 0800
786 232 in New Zealand.
Australia
www.sunbeam.com.au
1300 881 861
Units 5 & 6,
13 Lord Street,
Botany NSW 2019
Australia
New Zealand
www.sunbeam.co.nz
0800 786 232
Level 6, Building 5,
Central Park,
660-670 Great South Road,
Greenlane, Auckland
New Zealand
Upon receipt of your claim, Sunbeam will
seek to resolve your difficulties or, if the
product is defective, advise you on how to
obtain a replacement or refund.
To assist us in managing warranty claims,
we recommend you register your product
as soon as practicable after purchase by
creating a MySunbeam account on our
website and uploading a copy of your
original receipt.
In order to make a claim under our
warranty, you must have the original proof
of purchase documentation for the
product and present it when requested (if
not already uploaded to our website).
Should your product develop any defect
within 12 months of purchase because of
faulty materials or workmanship, we will
replace or repair it, at our discretion, free
of charge. A product presented for repair
may be replaced by a refurbished product
of the same type rather than being
repaired. Refurbished parts may be used
to repair the product.
Our replacement or repair warranty only
applies where a defect arises as a result
of faulty material or workmanship during
the warranty period. Your warranty does
not cover misuse or negligent handling
(including damage caused by failing to use
the product in accordance with this
instruction booklet), accidental damage,
or normal wear and tear.
Your warranty does not:
• cover freight or any other costs incurred
in making a claim, consumable items,
accessories that by their nature and
limited lifespan require periodic renewal
(such as filters and seals) or any
consequential loss or damage; or
• cover damage caused by:
- power surges, power dips, voltage
supply problems, or use of the product
on incorrect voltage;
- servicing or modification of the
product other than by Sunbeam or an
authorised Sunbeam service centre;
- use of the product with other
accessories, attachments, product
supplies, parts or devices that do not
conform to Sunbeam specifications; or
- exposure of the product to
abnormally corrosive conditions; or
• extend beyond 3 months if the product
is used in commercial, industrial,
educational or rental applications.
The benefits given to you by our
warranty are in addition to other rights
and remedies under law in relation to
the product.
In Australia our goods come with
guarantees that cannot be excluded
under the Australian Consumer Law. You
are entitled to a replacement or refund
for a major failure and for compensation
for any other foreseeable loss or
damage. You are also entitled to have the
goods repaired or replaced if the goods
fail to be of acceptable quality and the
failure does not amount to a major
failure.
Our goods also come with guarantees
that cannot be excluded under the New
Zealand Consumer Guarantees Act.
If your warranty claim is not accepted, we
will inform you and if requested to do so
by you, repair the product provided you
pay the usual charges for such repair.
You will also be responsible for all freight
and other costs.
Should your product require repair or
service after the warranty period, contact
your nearest Sunbeam service centre.
For a complete list of Sunbeam’s service
centres, visit our website or call our
customer service line for advice on 1300
881 861 in Australia, or 0800 786 232 in
New Zealand.
Need help with your appliance?
Contact our customer service team
or visit our website for information
and tips on getting the most from
your appliance.
New Zealand|visitwww.sunbeam.co.nz phone0800 786 232
mailLevel 6, Building 5, Central Park,
600-670 Great South Road,
Greenlane, Auckland, New Zealand.
Sunbeam Corporation Limited | ABN 45 000 006 771
Sunbeam Corporation is a division of GUD Holdings Limited.
Sunbeam is a registered trade mark.
Made in China to Sunbeam’s specification.
Due to minor changes in design or otherwise,
the product you buy may differ slightly from the one shown here.
Approved by the appropriate electrical regulatory authorities.