Sunbeam 3046 User Manual

Instruction Manual
Iron
Manual de Instrucciones
Plancha
www.sunbeam.com
P.N. 113951
MODEL / MODELO
IMPORTANT SAFEGUARDS
When using electrical appliances, basic safety precautions should always be followed including the following:
R
EAD
A
LLINSTRUCTIONS
B
EFORE
U
SE
• Use iron only for its intended use.
• To protect against risk of electric shock, do not immerse the iron in water or other liquids.
• The fabric select dial and steam lever should always be turned to “O/Off” before plugging or unplugging from out let. Never yank cord to disconnect from outlet; instead, grasp plug and pull to disconnect.
• Do not allow cord to touch hot surfaces. Let iron cool completely before putting away. Loop cord loosely around iron when storing.
• Always disconnect iron from electrical outlet when filling with water or emptying and when not in use.
• Do not operate iron with a damaged cord or if the iron has been dropped or damaged. To avoid the risk of electric shock, do not disassemble the iron. Take it to an authorized service center for examination and/or repair. Incorrect reassembly can cause a risk of electric shock when the iron is used.
• Close supervision is necessary for any appliance being used by or near children. Do not leave iron unattended while plugged in or turned on or on an ironing board.
• Burns can occur from touching hot metal parts, hot water or steam. Use caution when you turn a steam iron upside down – there may be hot water in the reservoir.
• If the iron is not operating normally, disconnect from the power supply and have the iron serviced by an authorized service center. Or call Customer Service at 800-458-8407.
• Your SUNBEAM
®
iron is designed to rest on the heel rest. Do not leave the iron unattended. Do not set the iron on an unprotected surface, even if it is on its heel rest.
SPECIAL INSTRUCTIONS
• This is a 1200-Watt appliance. To avoid a circuit overload, do not operate another high wattage appliance on the same circuit.
• If an extension cord is absolutely necessary, a 15-ampere cord should be used. Cords rated for less amperage may overheat. Care should be taken to arrange the extension cord so that it cannot be pulled or tripped over.
FOR PRODUCTS PURCHASED IN THE UNITED STATES AND CANADA
To reduce the risk of electrical shock, this appliance has a polarized plug (one blade is wider than the other). This plug fits a polarized outlet only one way; if the plug does not fit fully into the outlet, reverse the plug. If it still does not fit, contact a qualified electrician. Do not attempt to defeat this safety feature.
SAVE THESE INSTRUCTIONS
SUGGESTED FABRIC SELECT
FABRIC STEAM SETTING
DIAL SETTING
IRONING RECOMMENDATIONS
Acrylic
O
/Off (
Dry)
Synthetic
Iron garment inside out
Acetate
O
/Off (
Dry)
Synthetic
Iron garment inside out while still damp.
Polyester
O
/Off (
Dry)
Synthetic
Iron garment inside out while still damp.
Rayon
O
/Off (
Dry)
Synthetic
Iron garment inside out.
Silk
O
/Off (
Dry)
Silk
Iron garment inside out. Use an ironing cloth* to prevent shine marks.
Viscose
O
/Off (
Dry)
Silk
Mainly dry iron; steam may be used under garment manufacturer’s instructions.
Nylon
O
/Off (
Dry)
Silk
Iron garment inside out while still damp.
Wool Steam Wool
Iron garment inside out or use an ironing cloth.*
Wool Blends Steam Wool
Iron garment inside out or use an ironing cloth.*
Cotton Blends Steam Cotton
Follow garment manufacturer’s instructions. Use setting for the fiber requiring
t
he lowest
setting.
Corduroy Steam Cotton
Iron garment inside out or use an ironing cloth* and then brush the garment with your hand to raise the texture of the fabric.
Cotton Steam Cotton
Iron dark fabrics inside out to prevent shine marks.
Linen Steam Linen
Iron garment inside out or use an ironing cloth* to prevent shine marks (especially on dark fabrics).
Denim Steam Linen
Use the SPRAY MIST®feature and/or the SHOT OF STEAM
®
for deeper penetration
to remove wrinkles.
*An ironing cloth is a cotton, dry-cleaned cloth that you place over the garment
you are ironing to prevent the fabric from looking shiny.
Note: Some fabrics may require more steam than others. Your iron has the capability to adjust steam as needed.
IRONING GUIDE
FEATURES OF YOUR SUNBEAM®IRON
1. SPRAY MIST®Release
6
5
4
2. Covered Water Fill Hole
3. Steam Dial
4. SPRAY MIST®Button
®
5. SHOT OF STEAM
/ Vertical Steam Button
6. Power Indicator Light / MOTION SMART Auto-Off Indicator
7. Fabric Select Dial
8. See-Through Water Reservoir
9. Soleplate
3
7
2
8
1
®
9
TOF
ILL THEWATERRESERVOIR
1.Make sure the iron is unplugged. Set the Steam Lever to O/Off (Dry) and the Fabric Select Dial to OFF.
2.Lift the Water Fill Hole Cover.
3.Fill water cup with water. Pour water into iron water reservoir. Do not fill water reservoir beyond maximum fill level.
W
ARNING
:
To prevent the risk of burns, be careful when filling a hot iron with water. Hot metal parts, hot water and steam can cause injuries.
DRY IRONING
1.Make sure the Steam Lever is turned to the O/Off (Dry) setting.
2.Plug the cord into a 120-Volt AC outlet.
3.Turn the large Fabric Select Dial to the fabric setting you desire (Silk or Synthetics). Allow the iron to heat for 2 minutes. While the iron is heating, make sure it is sitting on its heel rest on a stable, protected surface.
N
OTE
:
While the Steam Lever is turned to the O/Off (Dry) setting, you may still use the SHOT OF STEAM®or SPRAY MIST®feature. Please make sure the water reservoir is 1/4 full of water.
TIP:
Refer to the Ironing Guide for the recommended setting for your fabric.
STEAM IRONING
1.Follow the instructions for “Filling the Water Reservoir”.
2.Plug the cord into a 120-Volt AC outlet.
3.Turn the large Fabric Select Dial to the fabric setting you desire (Synthetic, Silk, Linen, Cotton or Wool). Allow the iron to heat for 2 minutes. While the iron is heating, make sure it is sitting on its heel rest on a stable, protected surface.
4.Allow the iron to heat for 2 minutes, and then turn the Steam lever to the appropriate setting.
TIP:
Refer to the Ironing Guide for the recommended setting for your fabric.
I
MPORTANT
:
When not ironing, always set the Steam Lever to O/Off (Dry)
and the Fabric Select Dial to OFF.
USING THE IRONS SPECIAL FEATURES
SPRAY MIST®FEATURE
The SPRAY MIST®feature is a powerful water spray mist that dampens the fabric to aid in removing wrinkles from heavy fabrics and for setting creases.
To use the SPRAY MIST®Feature:
Press the SPRAY MIST®button firmly.
SHOT OF STEAM®FEATURE
The SHOT OF STEAM®feature provides an extra burst of steam for deep penetration of stubborn wrinkles. You can use this feature while Dry or Steam ironing, but the water reservoir must be at least 1/4 full of water.
To use the SHOT OF STEAM®Feature:
Place the iron on top of the wrinkle and press the SHOT OF STEAM®button each time you would like an extra burst of steam. The SHOT OF STEAM®feature may be used continuously with just a short pause between shots.
VERTICAL STEAM
The vertical steam feature allows your iron to function as a garment steamer.
TIP:
When using the vertical steam on clothing, hang the clothing on a clothes hanger for best results. Hanging curtains and drapes may also be steamed.
To use Vertical Steam:
1.Make sure that the iron has heated up (2 minutes).
2.Hold the iron in a vertical position, with the iron close to but not touching the fabric you want to steam.
3.With your other hand, pull the fabric tight.
4.Press the SHOT OF STEAM®button for approximately 3-second intervals as you move the iron across the wrinkled area.
WARNING:
To prevent the risk of burns, keep your hand away from the area being steamed.
WARNING:
DO NOT steam garments while wearing them; this may result in injuries.
Loading...
+ 14 hidden pages