MODEL # 30310684
ITM. / ART. 1185375
Thank you for purchasing these Sunbeam® Wireless Linkable LED Wall Lights.
Please read all instructions before using your new Wireless Linkable LED Wall Lights.
IMPORTANT: FOR INDOOR AND DRY LOCATION USE ONLY. ADHESIVE TAPE MAY DAMAGE
SURFACE IF REMOVED.
SPECIFICATIONS
Battery type: AA *3 per unit
Photo and Motion
sensor
Rating: max 1W, 4.5V / DC, 2.4 GHz
PARTS
FUNCTIONS
Timer
switch
Linking indicator light
On / Off /
Linking /
Pairing
button
SENSING RANGE
Motion sensor detection distance: 3 - 5 m / 9.84 - 16.4 ft
Detection angle: 100º
Maximum distance between 2 units: 8 m / 26.2 ft
Photo and Motion Sensor Light
Light automatically turns on when sensor detects motion
and there is a lack of ambient light; automatically turns
off when no motion is detected within the selected time or
there is sufcient ambient light.
Adjustable Timer
Light automatically turns off if no motion is detected by
motion sensor for 15 / 30 / 45 seconds based on timer
switch position.
Linking Indicator Light
The units are linked when the red linking indicator light is
blinking. Linked units will turn on when one of the units
detects motion in low ambient light.
Low Battery Indicator
When batteries are running low, the unit will ash for
10 seconds when it detects motion in low ambient light.
This signals that battery replacement is needed.
NOTE: A unit in a room with sufcient
ambient light will not illuminate.
IMPORTANT SAFETY INSTRUCTIONS
This device complies with Part 15 of the FCC Rules and Industry Canada’s licence-exempt RSSs. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
WARNING: Changes or modications to this unit not expressly approved by the party responsible for compliance could void the
user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can
be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of
the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio / TV technician for help.
BATTERY INSTRUCTIONS & CAUTIONS: Always purchase the correct size and grade of battery most suitable for the intended
use. Always replace the whole set of batteries at one time, taking care not to mix old and new ones, or batteries of different types.
Clean the battery contacts and also those of the device prior to battery installation. Ensure the batteries are installed correctly
with regard to polarity (+ and -). Remove batteries from equipment which is not to be used for an extended period of time.
Remove used batteries promptly. For recycling and disposal of batteries to protect the environment, please check the internet or
your local phone directory for local recycling centers and / or follow local government regulations.
For information about ordering parts or
how to expand your kit, please call us at
1-877-383-6399 (8:30 am – 5:30 pm E.S.T.)
Monday - Friday or contact us at
www.limagehomeproducts.com
If you have any problems, please do not contact the store.
Our customer service will be happy to assist you.
LIMITED WARRANTY
This product is guaranteed to operate a minimum of 1 year from
the original date of purchase. If, under normal use and for the
full time period, your product fails to operate, please return it to:
Quality Control Dept., L’Image Home Products, Inc., 1175 Place
du Frère-André, Montreal, Quebec, Canada H3B 3X9 (with your
original proof of purchase receipt) and we will refund it. This
warranty is considered void if the product fails from misuse.
Distributed by:
Costco Wholesale Corporation
P.O. Box 34535
Seattle, WA 98124-1535
USA
1-800-774-2678
www.costco.com
© 2017 Sunbeam Products, Inc. doing business as Jarden Consumer Solutions.
All rights reserved. SUNBEAM® logo is a registered trademark of
Sunbeam Products, Inc. used under license. Distributed by
L’Image Home Products Inc., Montreal, Canada H3B 3X9. LHP1115-090117
MADE IN CHINA
SAVE THESE INSTRUCTIONS
SETUP AND INSTALLATION
Before installation, make sure the surface you intend to mount the product on is free of moisture, oil, grease, dust
and dirt to ensure proper adhesion. Test painted surfaces. Adhesive tape may damage surface when removing.
SETUP
There are 2 ways to operate the units.
A. Stand-alone unit: Set the timer switch to the desired
light duration (FIG. 1). Insert 3 batteries in each unit (FIG. 2).
Press the On / Off button once, the light will turn on (FIG. 3).
If there is sufcient ambient light or no motion is detected,
the light will turn off when the preset time has elapsed.
B. Linked with other unit(s): Set the timer switch to the
desired light duration (FIG. 1). Press the On / Off button
twice (FIG. 4). The linking indicator light will turn on and
ash, indicating the unit(s) are linked (FIG. 5). Repeat for all
other units. Linked units will turn on when one of the units
detects motion in low ambient light.
To unlink a unit, press the On / Off button once. The linking
indicator light will turn off.
NOTE: A unit in a room with sufcient
ambient light will not illuminate.
NOTE: Linkable up to 10 units,
maximum 8 m / 26.2 ft between 2 units.
INSTALLATION
There are 3 ways to mount the unit.
A. Double-sided foam adhesive tape:
Mark the desired area where you want to install. Remove
one side of the tape and secure to the back of the LED light.
Then remove the other side of the tape and secure to where
you want to install (FIG. 6).
B. Drywall surface mounting anchor screw:
Place the mounting plate over the desired mounting location
and mark the center of the holes to be drilled. Drill two
pilot holes 0.45 - 0.50 cm / 0.18 - 0.20 in diameter into the
surface. Insert the anchors. Place the mounting plate over
the holes and screw in the mounting screws 2 cm / 0.79 in
to secure (FIG. 7).
C. Wood surface mounting screw:
Place the mounting plate over the desired mounting location
and mark the center of the holes to be drilled. Then place
the mounting plate over the marks and screw in the
mounting screws 1.2 cm / 0.47 in to secure (FIG. 8).
FIG. 1
FIG. 2
FIG. 3
FIG. 4 FIG. 5
FIG. 6
FIG. 7
NOTE: To prevent damage to the wall,
use adhesive glue remover.
Follow the manufacturer’s instructions.
If you have purchased more than one pack and
want to link more than 3 units, please follow pairing
instructions below.
PAIRING ADDITIONAL UNITS
All units within the package are already paired at the time
of purchase.
STEP 1
Designate one of the units as your master unit:
First, insert 2 batteries (FIG. 9). When inserting the 3rd
battery, press and hold the On / Off button (FIG. 10). The red
linking indicator light will ash, indicating the unit is ready
to be paired (FIG. 12).
STEP 2
Pairing new units with the master unit:
Insert all 3 batteries into the unit to be paired. Press and
hold the On / Off button (FIG. 11). The unit light will ash 2
times within 3 seconds. Pairing is now complete (FIG. 12).
Release the On / Off button.
Repeat (STEP 2) for the next units to be paired.
NOTE: Pairing time limit (3 minutes):
the linking indicator light of the
master unit will turn off after 3 minutes.
After 3 minutes, you will need to re-start
the entire pairing procedure.
FIG. 8
FIG. 9
FIG. 11
FIG. 10
FIG. 12
For troubleshooting tips or to
download this instruction manual,
please visit the product page on our website:
www.limagehomeproducts.com
MODEL # 30310684
ITM. / ART. 1185375
TROUBLESHOOTING GUIDE
The light unit does not turn on (stand alone):
• Check that switch is in On or Auto mode.
• Batteries are running out. Replace the batteries.
• The unit will not illuminate if there is sufcient ambient light.
The light unit does not turn on when linked:
• Check linking indicator light at the bottom. When it is red it is linked. To link, press the
on/off button until you see the red light.
• The unit will not illuminate if there is sufcient ambient light.
• When two units are placed too close to each other, the light of one unit may affect the
unit next to it.
• Two units may be placed too far from one another, beyond the linking distance.
Maximum distance between 2 units is 8m / 26.2 ft.
• Maximum of 10 units can be linked.
Do I need to do pairing when I purchase the kit?
• No, all units within the same package (3-pack) are already paired.
If I bought 2 kits, could I pair 4 units in one group and the other 2 units
in another group?
• Yes, re-do pairing procedure. Finish pairing one group and then pair the second group.
Which unit is the master unit?
• Any unit can be the master unit. Follow the pairing procedure.
• You can pair up to 10 units, maximum 8m / 26.2ft. between units.
Is there a time limit when pairing?
• Yes, pairing needs to be done within 3 minutes. The linking indicator light of the
mas-ter unit will turn off after 3 minutes. After the 3 minutes, you will need to
re-start the entire pairing procedure.
When is it time to change the batteries or how do you know
the batteries are running low?
• When the batteries are running low, the unit will ash for 10 seconds when it detects
motion in low ambient light. This signals that battery replacement is needed.
When replacing the batteries do you have to re-do the pairing of that
unit with the others?
• No
Loading...