Sub-Zero IC36RIDLH, IC24RLH, ID30CI, IT30CIIDLH, IT30CILH Use & Care Guide

...
Integrated Refrigeration Use & Care Guide
INTEGRATED REFRIGERATION
Contents
4 Integrated Features
5 Interactive Controls
6 Storage
10 Operation
13 Care Recommendations
14 Technical Data
16 Troubleshooting
19 Sub-Zero Warranty
CALIFORNIA PROPOSITION 65
WARNING
This product may contain chemicals known to the state of California to cause cancer or reproductive harm.
Customer Care
The model and serial number are printed on the enclosed product registration card. Both numbers are also listed on the product rating plate. Refer to page 4 for rating plate location. For warranty purposes, you will also need the date of installation and name of your authorized Sub-Zero dealer. Record this information below for future reference.
If your product ever needs attention, be sure to use a Sub-Zero factory certied service provider recommended by our customer care center, or select one from our list of providers available at subzero.com/locator. All factory certi­ed service providers are carefully selected and thoroughly trained by us.
SERVICE INFORMATION
Model Number
Serial Number
Date of Installation
Certied Service Name
Certied Service Number
Authorized Dealer
Dealer Number
Important Note
To ensure this product is installed and operated as safely and efciently as possible, take note of the following types of highlighted information throughout this guide:
IMPORTANT NOTE highlights information that is especially
important.
CAUTION indicates a situation where minor injury or product
damage may occur if instructions are not followed.
WARNING states a hazard that may cause serious injury or
death if precautions are not followed.
IMPORTANT NOTE: Throughout this guide, dimensions in
parentheses are millimeters unless otherwise specied.
2 | Sub-Zero Customer Care 800.222.7820
Thank You
Thank you for your purchase. We look forward to being part of your home for decades to come. As a third-generation family-owned company, we take a very personal stake in the preservation of your family’s food. We built our business and our reputation on helping families serve the freshest food possible.
With your purchase, you receive one of the strongest warranties in the appliance industry. Take a moment to read the full warranty statement on page 19. It’s also important to register your Sub-Zero to ensure that you don’t miss out on exclusive owner benets, such as; assurance that you will be taken care of in the unlikely event that service becomes necessary during the warranty period, and a proof-of-purchase record in case of a home insurance claim. You may register by one of the following options:
Mail in the completed Sub-Zero product registration card.
Register online at subzero.com/register and create a personalized My Sub-Zero/Wolf
account using the serial number on your product.
Register by phone by calling Sub-Zero Customer Care at 800-222-7820.
As a Sub-Zero owner, you can count on ongoing support, day in and day out. Our cus­tomer care center is available 24 hours a day, seven days a week and staffed by knowl­edgeable product experts at our factory in Madison, Wisconsin. Should the need arise, simply call 800-222-7820 and speak with one of our product experts. They will help troubleshoot any issues you might have.
We are condent this guide will answer your questions about the features, operation, and maintenance of your Sub-Zero, but if you have additional questions, please contact us at 800-222-7820 or visit us online at subzero.com.
subzero.com | 3
INTEGRATED FEATURES
Integrated Features
FEATURE
1
Product Rating Plate
2
Interactive Control Panel
3
Freshness Cards
4
Door Shelves
5
Dairy Compartment
6
Glass Shelves
7
Refrigerator Drawers
8
Ice Container
9
Storage Drawers
10
Air Purication System
11
Water Filtration System
12
Automatic Ice Maker
13
Water Dispenser (dispenser models)
14
Condenser (behind grille)
11
2
10
13
7
1
14
Column all refrigerator.
11
2
5
4
6
3
5
1 10
14
Drawer all refrigerator.
4 | Sub-Zero Customer Care 800.222.7820
10
13
7
2
1
9
9
14
4 6
3
12
8
Tall combination.
INTERACTIVE CONTROLS
Interactive Control Panel
For initial start up, touch and hold ‘power’ on the control panel for 2 seconds.
Temperature can be adjusted in one-degree increments on the home screen. Combination units have separate temper­ature controls for refrigerator and freezer. Temperatures are preset at 38°F
(3°C) and 0°F (-18°C). To change temperature,
touch the temperature being adjusted, then press ‘+’ or ‘–’ until the desired temperature is displayed. Refer to the illus­tration below.
Once the temperature has been adjusted, additional features can be activated or deactivated from the options screen. Touch
to view the options screen. Refer to the
illustration below.
Home screen.
OPTIONS SCREEN
Touch to activate or deactivate ice maker system and max ice feature.
Touch to activate or deactivate door/drawer alarm.
Touch to activate or deactivate water dispenser.
Touch to activate or deactivate air purication system.
Touch to view settings screen.
SETTINGS SCREEN
Touch to view model information.
Touch to select temperature unit, Fahrenheit or Celsius.
Touch to adjust control panel brightness and contrast.
Touch to adjust door/drawer alarm volume and pitch.
Touch to adjust door/drawer alarm duration.
Options screen.
Touch to enter Sabbath mode.
Touch to view troubleshooting and service information.
Touch to set clock.
Touch to select smart home options.
Touch to select language options.
Touch to adjust soft on lighting.
subzero.com | 5
STORAGE
Keeping Food At Its Best
This Sub-Zero features a unique dual refrigeration system to keep food fresher longer.
With the Sub-Zero dual refrigeration system, individual refrigerator and freezer systems have been designed to maintain accurate, consistent temperatures and proper humidity levels for longer food life expectancy. Dual refrig­eration eliminates transfer of fresh food odors to frozen food and ice and does not freeze the moisture out of the air in the fresh food section.
For handy tips and information on how to maximize food freshness, refer to the freshness cards stored in the refrigerator.
Refrigerator Storage
DOOR SHELVES
To remove a door shelf or the dairy compartment, lift from the bottom and slide out. To reinstall, place in the desired position and slide the shelf down onto the guides. Refer to the illustration below.
IMPORTANT NOTE: If door opening is limited to 90°, door
shelves may need to be removed before removing a storage drawer or glass shelf.
Door shelf removal.
6 | Sub-Zero Customer Care 800.222.7820
STORAGE
Refrigerator Storage
GLASS SHELVES
To remove or adjust a glass shelf, tilt up, then lift up and out. To reposition, insert shelf in the tracks along the back wall, then lower the front until it locks into position. Refer to the illustration below.
The stationary glass shelf at the bottom of the compartment should be placed with beveled edge facing front. Rear sup­port legs space the shelf away from the back wall to ensure proper air ow through the unit.
IMPORTANT NOTE: Use care when handling glass shelves to
prevent breakage or scratching the interior.
CAUTION
Glass shelves should warm to room temperature before immersing in warm water.
REFRIGERATOR DRAWERS
To remove a refrigerator drawer, pull open until the drawer stops. Lift the front of the drawer slightly and pull straight out. To reinstall, pull drawer carrier out and align the bottom of the drawer with the carrier. Refer to the illustration below.
Dividers in refrigerator drawers can be removed by pulling straight up. To replace, align tabs on the divider with notches in the drawer and push down.
Refrigerator drawer removal.
Glass shelf removal.
subzero.com | 7
STORAGE
Freezer Storage
FREEZER BASKETS
To remove, pull forward until basket stops. Pull the two plastic tabs located behind the bottom two corners of the basket forward, then lift up and out. To reinstall, push drawer slides in. Align the basket with slides and push back until it stops. Press down on the front of the basket to engage slides. Refer to the illustration below.
If door opening is limited to 90°, the top basket must be removed before removing the middle or lower basket.
ICE CONTAINER
Column | To remove ice container, pull freezer drawer open
until it stops and lift container out. Refer to the illustration below.
Column model IC-24CI | To remove ice container, pull freezer drawer open until it stops and slightly angle the con­tainer to lift out. Refer to the illustration below.
Tall and drawer | To remove ice container, pull freezer drawer open until it stops and lift container out. Refer to the illustration below.
The ice maker must be turned off by touching
when the ice storage container is removed. The unit is equipped with a 3-minute delay after the ice container is removed, to ensure cubes are not ejected before ice maker can be deac­tivated or ice container is reinstalled.
Freezer basket removal.
Model IC-24CI ice container. Tall and drawer ice container.
Column ice container.
8 | Sub-Zero Customer Care 800.222.7820
STORAGE
Storage Drawers
CRISPER COVER
The crisper cover in the upper storage drawer can be slid closed or left open.
To remove, pull the upper drawer all the way out, raise the front edge of the crisper cover and pull it forward out of the drawer. Refer to the illustration below.
DRAWER DIVIDERS
To remove or adjust a short divider, ex the long divider slightly, then pull upward. Refer to the illustration below.
To remove a long divider, the short dividers must be removed. Pull divider up until it stops, rotate counterclock­wise, then pull upward. To reinstall, align grooves with drawer tabs, rotate clockwise, then slide down.
DRAWER REMOVAL
To remove, pull open until drawer stops. Raise the drawer front and pull out drawer. To reinstall, raise the front of drawer and place onto the slides. Align the back of the drawer with hooks on the slide, then align the white pegs at the front of the slide with holes at the front of the drawer. Refer to the illustration below.
IMPORTANT NOTE: For drawer models, the upper drawer
has a control cable that must be disconnected before removing the drawer. Refer to the illustration below.
Crisper cover.
Drawer dividers.
Drawer removal.
Control cable (drawers).
subzero.com | 9
OPERATION
Air Purication System
The advanced air purication system of Sub-Zero integrated models reduces bacteria, odors and ethylene gas, which causes premature ripening in fruits and vegetables. If your unit is equipped with an air purication system, the cartridge has been factory installed and is located on the back wall of the refrigerator (back of upper drawer for drawer models).
To initiate air purication, touch
on the options screen.
The cartridge will last approximately one year. ‘Change Air Purier’ will appear on the control panel when the cartridge needs to be replaced. Touch ‘Snooze’ to delay reminder for 24 hours or until cartridge can be replaced.
Replacement Sub-Zero air purication cartridges can be ordered online at subzerowolfstore.com. For questions, contact Sub-Zero customer care at 800-222-7820.
CAUTION
The air purication system complies with applicable Federal requirements regarding incidental exposure to ultraviolet light. Lamp contains mercury. Manage in accordance with disposal laws. Visit earth911.com or call 800-222-7820.
AIR PURIFICATION CARTRIDGE REPLACEMENT
1 To access the air purication cartridge, grasp the outside
cover from the bottom and rotate upward (top and rotate downward for drawers). Refer to the illustrations below.
2 Grasp the black cover from the top and rotate down-
ward. The cartridge will pop out and can be removed.
3 Remove the new cartridge from packaging and insert
with connector pointing downward.
4 Once in position, close the black cover. Then rotate the
outside cover downward (upward for drawers).
5 Once the cartridge has been replaced, follow instructions
on the control panel. The cartridge life cycle will reset for approximately one year.
10 | Sub-Zero Customer Care 800.222.7820
Air purication cartridge (column and tall).
Air purication cartridge (drawers).
OPERATION
Water Filtration System
The water ltration system of Sub-Zero integrated models supplies ltered water to the ice maker and water dispenser (dispenser models) to produce great-tasting water and ice.
IMPORTANT NOTE: When using the water ltration system
for the rst time and after lter replacement, it is neces­sary to clear any air from the system and allow the lter to assist in cleaning the water lines. For non-dispenser models, discard the rst two full containers of ice. For dispenser models, dispense several glasses of water for a period of two minutes.
If the water ltration system will not be utilized, it can be placed in water lter bypass mode by removing the lter.
The lter is rated for 750 gallons
(2839 L) or one year,
whichever comes rst. ‘Change Water Filter’ will appear on the control panel when the cartridge needs to be replaced. Touch ‘Snooze’ to delay reminder for 24 hours or until lter can be replaced.
Replacement Sub-Zero water lters can be ordered online at subzerowolfstore.com. For questions, contact Sub-Zero customer care at 800-222-7820.
WATER FILTER REPLACEMENT
1 To access the water lter, pull out on the bottom edge
of the access door and rotate upward. Refer to the illus­tration below.
2 To remove the old lter, rotate counterclockwise one-
quarter turn, then pull out. It is normal for a small amount of water to drip when the lter is removed. It should be wiped up with a paper towel or cloth.
3 Remove the new lter from packaging and remove
plastic cap.
4 Insert the new lter into the manifold and turn clockwise.
5 Once the new lter has been installed, follow instructions
on the control panel. The lter life cycle will reset for approximately one year.
ACCESS DOOR
WATER FILTER
Water lter removal.
subzero.com | 11
OPERATION
Ice Maker Operation
To initiate ice production, touch the indicator on the options screen. A single highlighted cube indicates the ice maker is active. Three highlighted cubes indicate the max ice feature is active. Max ice increases ice production up to 30% for a 24-hour period. During that period, some com­ponents may run at a higher speed resulting in a unique audible tone. This is typical and will revert back after 24 hours or when the ice container is full. To deactivate the ice maker, touch
until no cubes are highlighted. After initial start-up, discard the rst few batches of ice. The ice may contain impurities from new plumbing connections.
If ice is not used regularly it may fuse together. To avoid, discard ice and allow ice maker to replenish.
The ice maker must be turned off by touching
when the ice storage container is removed. The unit is equipped with a 3-minute delay after the ice container has been removed, to ensure cubes are not ejected before the ice maker can be deactivated or ice container is reinstalled.
Sabbath
Water Dispenser
The water dispenser is located inside the refrigerator on the left wall. Press a glass against the dispenser to activate water ow. Water ow will stop when the glass is pulled away. Refer to the illustration below.
The chilled water reservoir tank holds approximately 40 oz
(1.2 L) of ltered water. It may take several hours to chill the
water to refrigerator temperature during the original ll and after a large amount of water is dispensed.
To ll the tank, press a glass against the dispenser until water begins to ow. A safety feature was incorporated into the dispenser to limit continuous water ow to 60 seconds. If water does not dispense within 60 seconds, remove the glass, then reapply to the dispenser until water begins to ow. Once the tank is full, discard the rst few glasses of water. It may contain impurities from new plumbing connections.
This appliance is certied by Star-K to meet strict religious regulations in conjunction with specic instructions found on www.star-k.org.
For Sabbath mode, from the settings screen, touch
and
follow instructions on the control panel.
WATER DISPENSER
Water dispenser.
12 | Sub-Zero Customer Care 800.222.7820
CARE RECOMMENDATIONS
Cleaning
INTERIOR CLEANING
To clean interior surfaces and all removable parts, wash with a mild solution of soap, water and baking soda. Rinse and dry thoroughly. Avoid getting water on lights and control panel.
CAUTION
Do not use vinegar, rubbing alcohol or other alcohol­based cleaners on any interior surface.
STAINLESS STEEL EXTERIOR
Use a nonabrasive stainless steel cleaner and apply with a soft lint-free cloth. To bring out the natural luster, lightly wipe surface with a water-dampened microber cloth followed by a dry polishing chamois. Always follow the grain of stainless steel.
CONDENSER CLEANING
CAUTION
Before cleaning the condenser, turn power off at the control panel. Wear gloves to avoid injury from sharp condenser ns.
The condenser is located behind the grille. Remove the kickplate by extracting the two mounting screws. Refer to the illustration below. Use a soft bristle brush and vacuum to remove dust and lint from the condenser. Clean the con­denser every three to six months.
IMPORTANT NOTE: To avoid damaging condenser ns,
vacuum in the direction of the ns.
CAUTION
Failure to clean the condenser could result in tempera­ture loss, mechanical failure or damage.
VACATIONS
For extended vacations, turn power off at the control panel. Empty the unit and block doors open slightly to let fresh air in and keep interior dry. Water lter should be replaced before start up.
CONDENSER
SCREW
Condenser location.
subzero.com | 13
TECHNICAL DATA
Sub-Zero Water Filtration System Data
REPLACEMENT CARTRIDGE (4204490)
Tested and certied by NSF International against NSF/ANSI Standard 42 for the reduction of Chlorine Taste & Odor, Particulate Class I; and against NSF/ANSI Standard 53 for the reduction of Lead, Mercury, Atrazine, Benzene, Carbofuran, 1,4-dichlorobenzene, Lindane, Toxaphene, Turbidity, Cysts and Asbestos.
This system has been tested according to NSF/ANSI 42/53 for reduc­tion of the substances listed below. The concentration of the indicated substances in water entering the system was reduced to a concentra­tion less than or equal to the permissible limit for water leaving the system, as specied in NSF/ANSI 42/53.
OPERATING SPECIFICATIONS
Capacity: certied for up to 750 gallons (2,838 L); up to twelve months Pressure Requirement: 35 – 120 psi (2.8 – 8.2 bar) Temperature: 33 – 100°F (0.6 – 38°C) Flow Rate: 0.78 gpm (2.9 Lpm)
Standard
Chlorine, Taste & Odor 42 2.0 mg/L ± 10% 1.88 mg/L 0.05 mg/L 0.06 mg/L 97.34% 96.80% ≥ 50%
Particulate 42
Lead at pH 6.5 53 0.15 mg/L ± 10% 0.153 mg/L <0.001 mg/L <0.001 mg/L 99.34% 99.34% 0.010 mg/L
Lead at pH 8.5 53 0.15 mg/L ± 10% 0.150 mg/L <0.001 mg/L <0.001 mg/L 99.33% 99.33% 0.010 mg/L
Mercury at pH 6.5 53 0.006 mg/L ± 10% 0.006 mg/L 0.0003 mg/L 0.0005 mg/L 95.00% 91.66% 0.002 mg/L
Mercury at pH 8.5 53 0.006 mg/L ± 10% 0.006 mg/L 0.0008 mg/L 0.0015 mg/L 86.66% 75.00% 0.002 mg/L
Atrazine 53 0.009 mg/L ± 10% 0.009 mg/L <0.002 mg/L <0.002 mg/L 77.77% 77.77% 0.003 mg/L
Benzene 53 0.015 mg/L ± 10% 0.014 mg/L 0.0006 mg/L 0.0011 mg/L 95.71% 92.14% 0.005 mg/L
Carbofuran 53 0.08 mg/L ± 10% 0.081 mg/L <0.001 mg/L <0.001 mg/L 98.76% 98.76% 0.04 mg/L
1,4-dichlorobenzene 53 0.225 mg/L ± 10% 0.208 mg/L <0.0005 mg/L <0.0005 mg/L 99.75% 99.75% 0.075 mg/L
Lindane 53 0.002 mg/L ± 10% 0.002 mg/L 0.00003 mg/L 0.00007 mg/L 98.50% 96.50% 0.0002 mg/L
Toxaphene 53 0.015 mg/L ± 10% 0.015 mg/L <0.001 mg/L <0.001 mg/L 93.33% 93.33% 0.003 mg/L
Turbidity 53 11 ± 1 NTU 10.7 NTU 0.31 NTU 0.49 NTU 97.10% 95.42% 0.5 NTU
Cysts** 53 Minimum 50,000/L 166,500/L <1/L <1/L >99.99% >99.99% >99.95%
Asbestos 53 10
**Based on the use of Cryptosporidium Parvum oocysts † Fibers greater than 10 μm in length
Concentration
At least 10,000
particles/ml
7
to 108 bers/L
Inuent Challenge
NSF
Average Inuent
Concentration
5,700,000/ml 30,583/ml 69,000/ml 99.46% 98.78% ≥ 85%
155 MF/L <1 MF/L <1 MF/L >99.99% >99.99% >99%
Product Water Concentration % Reduction
Max Permissable
Product Water ConcentrationSubstance Average Max Efuent Average Minimum
SPECIAL NOTES
Replacement Sub-Zero water lter cartridges can be ordered online
at subzerowolfstore.com. For questions, contact Sub-Zero customer care at 800-222-7820.
Change lter cartridge at least every twelve months. High sediment
areas may require more frequent lter cartridge replacement.
Installation and operation instructions, parts and service availability,
and standard warranty are included with the product when shipped.
Replace water lter cartridge when the lter indicator is lit or when
water ow becomes too low. Use replacement water lter cartridge part number 4204490. Replacement lter pricing information can be found at subzero.com.
Do not use with water that is microbiologically unsafe or of unknown
water quality without adequate disinfection before or after the system.
Systems certied for cyst reduction may be used on disinfected
waters that may contain lterable cysts.
This system must be installed, operated, maintained and lters
replaced as required in order for the product to perform as adver­tised.
Note that while the testing was performed under standard labora-
tory conditions, actual performance may vary. The contaminants or other substances removed or reduced by this water treatment system are not necessarily in your water.
Manufactured for: Sub-Zero, Inc., P.O. Box 44848, Madison, WI 53744, 800-222-7820
14 | Sub-Zero Customer Care 800.222.7820
TECHNICAL DATA
subzero.com | 15
TROUBLESHOOTING
Troubleshooting
UNIT OPERATION
No lights or cooling.
Verify power is on.
Verify electrical power to unit and home circuit breaker
is on.
No lights in refrigerator or freezer.
Door/drawer may have been left ajar which has disabled
lights to eliminate excess heat. If lights are out, close door/drawer for one hour. If lights are still out, contact Sub-Zero factory certied service.
LED interior lighting must be replaced by Sub-Zero
factory certied service.
Frost, condensation or ice build up inside unit.
Verify condenser is clean.
Verify door/drawer is closing properly.
Verify door/drawer has not been left ajar.
Verify door/drawer gasket does not have rips or tears. If
it does, contact Sub-Zero factory certied service.
High temperatures, unit runs excessively or unit giving off too much heat.
Verify condenser is clean.
Verify door/drawer is closing properly.
Verify door/drawer has not been left ajar.
Increased ambient temperatures may cause compres-
sors to run longer.
If temperature display shows 38° and 0°, but is not
cooling, unit may be in showroom mode. Contact Sub-Zero Customer Care at 800-222-7820.
No water from dispenser.
Wait one hour, then try dispenser again. Contact
Sub-Zero Customer Care at 800-222-7820 if unresolved.
If icing is heavy, turn unit off and use a hair dryer to melt
ice. Hair dryer should be set on low and kept moving at all times. Once ice has melted, wipe up water with a cloth or paper towel.
16 | Sub-Zero Customer Care 800.222.7820
TROUBLESHOOTING
Troubleshooting
ICE PRODUCTION
No ice.
Verify ice cube indicator appears in control panel display.
Verify ice maker has been on for at least 24 hours.
Verify freezer temperature near 0°F.
Verify ice container is properly installed.
Verify ice maker arm in down position.
Verify water is being supplied to unit.
Verify water lter has been replaced within the last 12
months and installed properly.
Verify water lter has been removed if a reverse osmosis
ltration system is being utilized.
Blue or green ice.
Possible copper supply line corrosion. Contact plumber
to clean or replace.
Black ecks in cubes.
ODOR
Unit should be cleaned before using for the rst time.
This will clear any odors that may have been trapped during shipping.
Replace air purication cartridge.
Clean unit and shelving thoroughly.
Uncovered food could create odor which may require
cleaning.
Stop use and contact Sub-Zero factory certied service.
Bad taste.
Defrost freezer and clean with soap and water.
Place coffee grounds or charcoal briquettes in freezer to
absorb odor.
Hollow cubes.
Clean condenser. Contact Sub-Zero factory certied
service if unresolved.
subzero.com | 17
Loading...
+ 39 hidden pages