SUBARU CX-CF7160 Service Manual

ORDER No. 6076
CUSTOM MADE FOR SUBARU CX-CF7160F
6-Disc CD Changer
SUBARU PART No. : H625SSA000 VEHICLE : FORESTER
DESTINATION : North America PRODUCED AFTER : Mar., 2002
I0
Specification*
General Power Supply DC 12V (11V - 16V),
Test Voltage 13.2V
Negative Ground Current Consumption Less than 1.5A Output Voltage 0.6V (10k)
CD Changer Signal to Noise Ratio More than 85dB (IHF-A) Total Harmonic Distortion Less than 0.05% Channel Separation More than 55dB (IHF-A)
Dimensions** (W×H×D) 178×165×50mm
Weight** 1.6kg
* Specifications and the design are subject to possible modification without notice due to improvements.
** Dimensions and Weight shown are approximate.
CUSTOM MADE FOR SUBARU / CX-CF7160F
CONTENTS
Page Page
1 FEATUERS 2 2 LASER PRODUCTS 3 REAR VIEW AND CONNECTORS 4 FRONT VIEW AND FUNCTIONS 5 WIRING CONNECTION 6 BLOCK DIAGRAM 7 TERMINALS DESCRIPTION 8 IC BLOCK DIAGRAM
9 REPLACEMENT PARTS LIST 9
2
10 EXPLODED VIEW (Unit)
3
11 CD CHANGER PARTS LIST 12 EXPLODE D VIEW (CD Deck-1)
3 4
13 EXPLODE D VIEW (CD Deck-2)
5
14 EXPLODE D VIEW (CD Deck-3) 15 WIRING DIAGRAM
7 8
16 SCHEMAT IC DIAGRAM
1 FEATUERS
6-disc CD changer (in dash board).
Hologram optical pick-up.
Shock proof memory.
High-speed disc change.
11 12 15 16 17 18 21
2 LASER PRODUCTS
2
3 REAR VIEW AND CONNECTORS
CUSTOM MADE FOR SUBARU / CX-CF7160F
4 FRONT VIEW AND FUNCTIONS
3
CUSTOM MADE FOR SUBARU / CX-CF7160F
5 WIRING CONNECTION
4
6 BLOCK DIAGRAM
6.1. Main Block
CUSTOM MADE FOR SUBARU / CX-CF7160F
5
CUSTOM MADE FOR SUBARU / CX-CF7160F
6.2. CD Servo Block
6
7 TERMINALS DESCRIPTION
CUSTOM MADE FOR SUBARU / CX-CF7160F
7.1. Main Block
IC600 : C2BBFE000062
Pin No.
1 LED2 OUT Panel LED on/off O 0 2 LED1 OUT Panel LED on/off O 0
3-6 - (Connecting to ground) - 0
7 AVref1 +5V power supply - 5.0 8 RXD (Connecting to ground) - 0
9 TXD (Connecting to ground) - 0 10 P.ON System power control O 5.0 11 SOM CD changer serial data I 4.2 12 SIM CD changer serial data O 0 13 SCKM Clock for serial data O 5.0 14 - Not used - -
15-18 - (Connecting to ground) - 0
19 /MDON CD Changrer start/stop O 5.0 20 /RESET CD changer reset O 5.1
21-24 - (Connecting to ground) - 0
25 KS1 Key strobe O 0 26 KS0 Key strobe O 0 27 KI2 Key data input I 0 28 KI1 Key data input I 0 29 KI0 Key data input I 0
30-32 - (Connecting to ground) - 0
33 Vss Ground - 0
34,35 - (Connecting to ground) - 0
36 AUDIO SW Audio signal selection O 9.6
37-43 - (Connecting to ground) - 0
44 - Not used - ­45 MITE-2 Mute control O 0 46 - (Connecting to ground) - 0 47 - Not used - -
48-59 - (Connecting to ground) - 0
60 RESET Reset input I 4.6 61 - (Connecting to ground) - 0 62 BATT-SENS Battery level detection I 4.4 63 ACC-SENS ACC level detection I 4.4 64 EJECT Eject switch I 4.3 65 BUS IN BUS-Line I 4.9 66 BUS OUT BUS-Line O 0 67 - (Connecting to ground) - 0 68 VDD +5V power supply - 5.0 69 X2 Crystal osillator - 2.4 70 X1 Crystal osillator - 1.2 71 IC (Connecting to ground) - 0 72 XT2 Not used - ­73 XT1 (Connecting to ground) - 0 74 AVDD +5V power supply - 5.0 75 GND Ground - 0 76 - (Connecting to ground) - 0 77 LED6 OUT Panel LED on/off O 0 78 LED5 OUT Panel LED on/off O 0 79 LED4 OUT Panel LED on/off O 0 80 LED3 OUT Panel LED on/off O 0
Note :
Voltage measuerments are with respect to ground, with a voltmeter (Internal resistance : 10M ohms.)
Port Descriptions I/O Vol
(V)
7.2. CD Servo Block
IC201 : MN662783RPW
Pin No.
1 VDD +5V power supply - 5.0 2 D0 D-RAM data I/O 2.3 3 D1 D-RAM data I/O 1.8 4 /WE D-RAM data write O 4.9 5 /RAS D-RAM row address strobe O 3.4 6 D2 D-RAM data I/O 0.8 7 D3 D-RAM data I/O 0 8 /CAS0 D-RAM columun address strobe O 3.9
9 /CAS1 D-RAM columun address strobe O 0 10 A8 D-RAM address O 0.6 11 A7 D-RAM address O 1.1 12 A6 D-RAM address O 0.7 13 A5 D-RAM address O 0 14 A4 D-RAM address O 1.1 15 A9 D-RAM address O 0.4
16-18 A0 D-RAM address O 1.0
19 A3 D-RAM address O 0 20 VSS2 Ground - 0 21 VDD2 +5V power supply - 5.0
22,23 - Not used - -
24 TVD Traverse motor control O 2.5 25 PC Not used - ­26 ECS Spindle motor control O 2.4 27 TRD Tracking coil drive O 2.5 28 FOD Focus coil drive O 2.4 29 FBAL Focus balance O 1.9 30 TBAL Tracking balance O 3.0 31 VREF Refence voltage I 2.5 32 FE Focus error I 2.5 33 TE Tracking error I 2.5 34 RFENV RF envelope I 2.5 35 OFT Off track signal I 0 36 /RFDET RF detecting signal I 0 37 BDO Drop-out signal I 0 38 LDON Laser on signal O 4.5 39 ARF RF signal I 2.5 40 IREF Reference current input I 1.2 41 DRF Bias for DSL I 2.4 42 DSLF Loop filter for DSL I/O 2.5 43 DSLF2 Loop filter for DSL I/O 2.2 44 PLLF Loop filter for PLL I/O 1.4 45 VCOF Not used - ­46 AVDD2 +5V power supply - 5.0 47 AVSS2 Ground - 0 48 OUTL L channel output O 2.3 49 AVSS1 Ground - 0 50 OUTR R channel output O 2.3 51 AVDD1 +5V power supply - 4.7
52-54 - (Connecting to ground) - 0
55 FLAG Flag output O 0 56 FCLK Frame clock O 0
57-59 - Not used - -
60 TX Not used - ­61 MCLK Clock for I/F command I 1.0 62 MDATA Date for I/F command I 3.1 63 MLD I/F command load I 5.0 64 BLKCK Subcode block clock O 0 65 SQCK Ext.clock for sub code-Q I 5.0 66 SUBQ Code for sub. code-Q O 3.8 67 DMUTE Mute input I 0
Port Description I/O (V)
7
Loading...
+ 15 hidden pages