How it Works
Stryker
Loading...
Trauma Stretcher 1037
Table of contents
Loading...

Stryker Trauma Stretcher 1037 Service manual [gb]

Download
Page 1
Trauma Stretcher
Model 1037
Maintenance Manual
For parts or technical assistance: USA: 1-800-327-0770
2010/07 1037-009-002 REV A www.stryker.com
Page 2
Page 3

Table of Contents

Symbols ............................................................................6
Warning/Caution/Note Definition ...........................................................6
Product Description ....................................................................7
Intended Use of Product.................................................................7
Specifications ........................................................................7
Contact Information ....................................................................8
Serial Number Location .................................................................8
Cleaning...............................................................................12
Stretcher Cleaning....................................................................12
Mattress Cleaning ....................................................................13
Preventative Maintenance ..................................................................15
Quick Reference Replacement Parts List ......................................................16
Service Information.......................................................................17
Caster Assembly Replacement...........................................................17
Brake Swivel Lock Ring Replacement ......................................................18
Brake Timing Link Replacement, Head End or Foot End ........................................19
Brake Cam Assembly Replacement .......................................................20
Brake Rod Replacement - Fifth Wheel Only .................................................21
Brake Rod Replacement - Big Wheel Only ..................................................22
Fifth Wheel Assembly Replacement .......................................................23
Jack Replacement, Head End - Fifth Wheel Only .............................................24
Jack Replacement, Head End - Big Wheel Only ..............................................25
Jack Replacement, Foot End - Fifth Wheel Only ..............................................26
Jack Removal, Foot End - Big Wheel Base with Three-Sided Controls ..............................27
Release Pedal (Side) Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Litter Top Removal....................................................................29
Transfer Board Counterbalance Adjustment .................................................30
Fold Down Siderail Latch Adjustment ......................................................30
Release Pedal Replacement, Foot End .....................................................31
Release Pedal Rod Removal, Foot End.....................................................31
Big Wheel Removal (Non Four-Sided Brakes) ................................................32
Big Wheel Removal (Four-Sided Brakes)....................................................32
Big Wheel Dampener Replacement .......................................................33
Pneumatic Fowler Adjustment ...........................................................34
Removal of Excess Air from the Hydraulic System ............................................35
Fifth Wheel Side Control Brake Assembly ......................................................41
www.stryker.com 1037- 009-002 REV A 3
Page 4
Table of Contents
Lowering Pedal Assembly - 1115-004-201 ......................................................70
Big Wheel Four-Sided Control Base Assembly...................................................71
Base Labeling Assembly, Standard Brakes .....................................................77
Base Labeling Assembly, Four-Sided Brakes ....................................................78
Base Labeling Assembly - Big Wheel Base .....................................................79
Siderail, Left - 1010-026-017................................................................87
X-Ray Tray Assembly, Left Side Load - 1037-021-000 .............................................97
Optional X-Ray Centering Guide - 1020-020-000 ................................................10 0
Optional Push Handles, Head End - 1037-151-000 ...............................................101
Push Handle Assembly - 1211-351-010 .......................................................102
Optional Push Handles, Foot End - 1037-051-000 ...............................................103
Push Handle Assembly With I.V., Head End - 1037-151-004 ........................................104
Push Handle Assembly Without I.V., Head End - 1020-151-001 ......................................105
Cover Assembly with Pop Up Push Handles, Head End - 1037-151-005................................10 6
4 1037- 009-002 REV A www.stryker.com
Page 5
Table of Contents
Optional Accessories ....................................................................108
C-Spine Cassette Holder Assembly - 1020-070-000 .............................................109
C-Spine Storage Bracket Assembly - 1020-070-019..............................................1 10
Defibrillator Tray Assembly - 1105-045-200 ................................................... 1 12
Defibrillator Tray/Foot Extender/Foot Board - 1105-045-400 .......................................1 13
Footboard/Chartholder Assembly - 1105-045-500 ...............................................1 14
Fowler X-Ray Cassette Assembly - 1020-023-000 ...............................................1 15
Heel Stirrups - 1020-055-000 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 116
I.V. Caddy - 0785-155-000.................................................................1 17
Removable I.V. Pole - 0390-025-000 .........................................................118
Tethered I.V. Pole Assembly - 1001-087-018 ...................................................119
Two-Stage I.V. Pole Assembly, Head End 1010-081-000 ...........................................12 0
Three-Stage I.V. Pole Assembly, Head End 1020-061-000/ ........................................ 121
Three-Stage I.V. Pole Assembly, Foot End 1020-062-000 .......................................... 121
Two-Stage I.V. Pole Assembly, Foot End 1010-080-000 ...........................................12 2
Upright Oxygen Bottle Holder - 1115-130-000 ..................................................12 3
Serving Tray - 1105-045-700............................................................... 12 4
Foot Board/Serving Tray Holder - 1105-045-800 ................................................12 5
Mattresses and Siderail Pads . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 6
Warranty .............................................................................12 7
Limited Warranty ....................................................................127
To Obtain Parts and Service ........................................................... 12 7
Service Contract Coverage ............................................................12 7
Service Contract Programs ............................................................12 8
Return Authorization.................................................................. 12 8
Damaged Merchandise ...............................................................12 8
International Warranty Clause...........................................................12 8
www.stryker.com 1037- 009-002 REV A 5
Page 6

SYMBOLS

Symbols and Definitions

Warning/Caution: Consult accompanying documentation
Safe Working Load indicates the sum of the patient, mattress, and accessory weight
Do not store oxygen bottle
Do not push/pull
Manufacturer

WARNING/CAUTION/NOTE DEFINITION

The words WARNING, CAUTION and NOTE carry special meanings and should be carefully reviewed.
WARNING
Alerts the reader about a situation which, if not avoided, could result in death or serious injury. It may also describe potential serious adverse reactions and safety hazards.
CAUTION
Alerts the reader of a potentially hazardous situation which, if not avoided, may result in minor or moderate injury to the user or patient or damage to the equipment or other property. This includes special care necessary for the safe and effective use of the device and the care necessary to avoid damage to a device that may occur as a result of use or misuse.
NOTE
Provides special information to make maintenance easier or important instructions clearer.
Return To Table of Contents
6 1037- 009-002 REV A www.stryker.com
Page 7

Introduction

This manual is designed to assist you with the operation of Stryker Model 1037 Trauma Stretcher. Read this manual thoroughly before using the equipment or beginning maintenance on it. To ensure safe operation of this equipment, it is recommended that methods and procedures be established for educating and training staff on the safe operation of this stretcher.

PRODUCT DESCRIPTION

The Stryker Model 1037 Trauma Stretcher is a general purpose patient transport and treatment stretcher.

INTENDED USE OF PRODUCT

The Stryker Medical Trauma Stretcher is a non-powered, wheeled device which consists of a platform mounted on a wheeled frame that is designed to support patients in a horizontal position. The device has siderails and has the option available to support the temporary or permanent placement of I.V. poles. A stretcher provides the operator a method of transporting patients within a healthcare facility. Some stretchers may also be used for minor procedures and short-term stay (treatment and recovery).

SPECIFICATIONS

Safe Working Load Note: Safe Working Load indicates the sum of the patient, mattress, and accessory weight.
Overall Stretcher Length 83” 210.8 cm
Minimum / Maximum Stretcher Height 24.5” / 37.5” 62.2 cm / 95.3 cm
Fowler Angle 0° to 90°
Trendelenburg / Reverse Trendelenburg +18°/-18°
6” nominal 15 c m
Minimum Under-Stretcher Clearance
1.75” under the hydraulic cylinders and fifth wheel
500 lb. 226.8 kg.
4.5 cm
Stryker reserves the right to change specifications without notice.
Return To Table of Contents
www.stryker.com 1037- 009-002 REV A 7
Page 8
Introduction

CONTACT INFORMATION

Contact Stryker Customer Service or Technical Support at: (800) 327-0770 or (269) 324-6500.
Stryker Medical 3800 E. Centre Avenue Portage, MI 49002 USA
Please have the serial number (A) of your Stryker product available when calling Stryker Customer Service or Technical Support. Include the serial number in all written communication.

SERIAL NUMBER LOCATION

A
Return To Table of Contents
8 1037- 009-002 REV A www.stryker.com
Page 9

Summary of Safety Precautions

Carefully read and strictly follow the warnings and cautions listed on this page.
Service only by qualified personnel. See the maintenance manual for additional information.
WARNING
• Always apply the brakes when a patient is getting on or off the stretcher. Push on the stretcher to ensure that the
brakes are securely locked. Always engage the brakes unless the stretcher is being moved. Injury could result if
the stretcher moves while a patient is getting on or off the stretcher.
• Patients should be discouraged from sitting directly on the ends of the stretcher. Excessive weight could cause
the litter surface to tip up, possibly causing patient injury.
• Leave the stretcher height in the lowest position when the patient is left unattended. Leaving the stretcher height
in a raised position could increase the chance of patient falls and injury.
• Make sure that the brakes are completely released before attempting to move the unit. Attempting to move the unit
with the brakes engaged could result in injury to the user and/or patient.
• After raising the siderails, pull firmly on the siderail to ensure that it is securely locked into the fully raised position.
Siderails are not intended to serve as a patient restraint device to keep patients from exiting the unit. Siderails are
intended to keep a patient from inadvertently rolling off the unit. It is the responsibility of the attending medical
personnel to determine the degree of restraint necessary to ensure that a patient will remain in place. Failure to
utilize the siderails properly could result in patient injury.
• When lowering the siderail to the collapsed position, keep extremities of patients and staff away from the siderail
spindles or injury could occur.
• During patient transfer, keep patient and operator extremities away from collapsed siderails or injury could occur.
• When using the transfer board to transfer a patient from one patient support platform (for example, bed, stretcher,
gurney, operating table) to another, always lock the brakes on both patient support platforms. Make sure that the
transfer board is placed securely on the surface of the patient support platforms. The patient support platforms
and surfaces must be at the same height before the patient is transferred.
• Operation of the pneumatic fowler is a manual procedure. Use caution when raising the fowler while a patient is
on the stretcher. Use proper lifting techniques and get additional assistance, if necessary. Failure to use proper
lifting techniques could cause injury to the operator.
• Keep hands/fingers clear of the area around the fowler release handle and the fowler frame when lowering the
fowler. Injury could result if care is not taken when lowering the fowler.
• If the stretcher is equipped with the optional foot end push handles, use caution while the foot extension/defibrillator
tray is installed to avoid pinching your fingers.
• To avoid the risk of injury to the patient or user or damage to the I.V. pole while transporting the stretcher, make sure
that the I.V. caddy is securely tightened on the I.V. pole.
CAUTION
• Do not modify this stretcher. Modifying the unit can cause unpredictable operation resulting in injury to the patient
or operator. Modifying the unit will also void its warranty.
• To avoid damage, remove any equipment that may be in the way before raising or lowering the litter height.
• Do not raise the unit (hydraulics on base) with a patient lift under the stretcher.
• Do not engage the steer pedal when the Big Wheel is resting on a threshold or other raised area. The force
required to engage the Big Wheel will be higher than normal, possibly causing damage.
• To avoid injury or damage to the equipment, do not allow the siderail to lower on its own.
Return To Table of Contents
www.stryker.com 1037- 009-002 REV A 9
Page 10
Summary of Safety Precautions
CAUTION (CONTINUED)
• The push handles were designed for use while transporting the stretcher. Avoid using other parts of the stretcher
as push/pull devices because damage could occur.
• When the transfer board is being used to transfer a patient, the support post must be in the stored (down) position.
Damage to the support post will occur if it is pushed up against a stretcher, table, etc.
• The weight capacity of the base hood is 60 lb. Do not sit or stand on the base hood. Injury or damage to the
equipment could occur.
• Do not step on the base hood.
• Do not use the cutout for the oxygen bottle holder on the base hood for the storage of oxygen bottles or patient
belongings.
• To avoid damage, do not put items weighing more than 30 lb. on the defibrillator tray.
• Do not use the defibrillator tray as a push/pull device because equipment damage could occur.
• If the stretcher is equipped with the optional foot end I.V. pole, the I.V. pole must be in the raised position when the
foot extension/defibrillator tray is installed. If the I.V. pole is not raised, the foot extension will not function properly
and injury could occur.
• To avoid damage, do not put items weighing more than 30 lb. on the defibrillator tray/foot extender.
• Do not use the defibrillator tray/foot extender as a push/pull device because equipment damage could occur.
• Do not use the footboard/chartholder as a push/pull device because equipment damage could occur.
• Always store the I.V. caddy when not in use to avoid damaging it when the unit is moved.
• To avoid damage, do not put items weighing more than 30 lb. on the serving tray.
• Do not use the serving tray as a push/pull device because equipment damage could occur.
• To avoid damage, the weight of the I.V. bags should not exceed 40 lb.
• To avoid damage while transporting the stretcher, verify that the I.V. pole is at a low enough height to allow it to
safely pass through door openings and under light fixtures.
• Do not use the I.V. pole as a push/pull device because equipment damage could occur.
• To avoid damage, the weight of the I.V. bags should not exceed 12 lb. while the weight of any one item attached to
each stage of the three-stage permanently attached I.V. pole should not exceed 9.3 lb.
• To avoid damage, do not put items weighing more than 40 lb. in the upright oxygen bottle holder.
• Do not use the upright oxygen bottle holder as a push/pull device because equipment damage could occur.
• Before returning the unit to service after cleaning, ensure that the unit is functioning properly by verifying that all
labels are intact, raise/lower the stretcher height, brake/steer pedal locks properly in both positions, latch/unlatch
the siderails, raise/lower the fowler and gatch, and check all components for proper lubrication.
• Some cleaning products are corrosive in nature and may cause damage to the product if used improperly. If the
products suggested above are used to clean Stryker patient handling equipment, measures must be taken to
ensure that the stretcher is wiped with a damp cloth soaked in clean water and thoroughly dried following cleaning.
Failure to properly rinse and dry the stretcher will leave a corrosive residue on the surface of the stretcher, possibly
causing premature corrosion of critical components. Failure to follow the above directions when using these types
of cleaners may void this product’s warranty.
NOTE
• Clean the base hood storage area regularly.
• The bottom of the brake pads should be cleaned regularly to prevent wax or floor remnant buildup.
Return To Table of Contents
10 1037- 009-002 REV A www.stryker.com
Page 11

Setup Procedures

Make sure that the unit is working properly before it is put into service. The following list will ensure that each part of the unit is checked.
1. Fully depress the brake pedal of the stretcher to set the four wheel brakes and verify that all four casters are locked.
2. Raise and lower the hydraulic lift system.
3. Raise the unit completely and activate the Trendelenburg function. Ensure that the head end lowers to the lowest position.
4. Raise the unit completely and activate the reverse Trendelenburg function. Ensure that the foot end lowers to the lowest position.
5. Activate the fifth wheel to ensure that it is operating properly or activate the Big Wheel to ensure that it is operating properly.
6. Ensure that the siderails raise and lower smoothly and lock securely when fully raised.
7. Raise and lower the fowler (head end).
CAUTION
Do not modify this stretcher. Modifying the unit can cause unpredictable operation resulting in injury to the patient or operator. Modifying the unit will also void its warranty.
Return To Table of Contents
www.stryker.com 1037- 009-002 REV A 11
Page 12

Cleaning

STRETCHER CLEANING

These instructions are intended to provide recommended cleaning methods for the Stryker Model 1037 Trauma Stretcher.
RECOMMENDED CLEANING METHOD
Note: Follow the cleaning solution manufacturer’s dilution recommendations exactly.
• Remove the mattress prior to washing the unit; do not wash the mattress with the stretcher.
• Wipe the unit with cleaning solution and water per manufacturer’s recommended dilution.
• Dry thoroughly. Do not replace the mattress on the stretcher until the unit is completely dry.
CAUTION
Before returning the unit to service after cleaning, ensure that the unit is functioning properly by verifying that all labels are intact, raise/lower the stretcher height, brake/steer pedal locks properly in both positions, latch/unlatch the siderails, raise/lower the fowler and gatch, and check all components for proper lubrication.
DO NOT STEAM CLEAN, PRESSURE WASH, HOSE OFF OR ULTRASONICALLY CLEAN THE STRETCHER. Using these methods of cleaning are not recommended and may void this product’s warranty.
RECOMMENDED CLEANERS
Suggested cleaners for stretcher surfaces: Quaternary Cleaners (active ingredient - ammonium chloride). Phenolic Cleaners (active ingredient - o-phenylphenol). Chlorinated Bleach Solution (5.25% - less than 1 part bleach to 100 parts water).
Avoid over saturation and ensure the product does not stay wet longer than the chemical manufacturer’s guidelines for proper disinfecting.
CAUTION
Some cleaning products are corrosive in nature and may cause damage to the product if used improperly. If the products suggested above are used to clean Stryker patient handling equipment, measures must be taken to ensure that the stretcher is wiped with a damp cloth soaked in clean water and thoroughly dried following cleaning. Failure to properly rinse and dry the stretcher will leave a corrosive residue on the surface of the stretcher, possibly causing premature corrosion of critical components. Failure to follow the above directions when using these types of cleaners may void this product’s warranty.
Return To Table of Contents
12 103 7-0 09-002 REV A www.stryker.com
Page 13
Cleaning

MATTRESS CLEANING

These instructions are intended to provide recommended cleaning methods for stretcher mattresses.
RECOMMENDED CLEANING METHOD
• Hand-wash all surfaces of the mattress with warm water and mild detergent cleaner.
• Dry thoroughly.
• Apply disinfectant solution either by spray, solution or pre-impregnated wipes (do not soak mattress).
• Clean per hospital protocol for mattresses.
• Wipe up excess disinfectant.
• Rinse with clean water.
• Allow surface to dry.
RECOMMENDED DISINFECTANTS
IMPORTANT: DILUTE ALL DISINFECTANTS IN ACCORDANCE WITH MANUFACTURER’S DIRECTIONS
When used in concentrations recommended by the manufacturer, diluted bleach, diluted phenolic, or diluted quaternary germicidal disinfectants are recommended. Chlorine Bleach, typically 5.25% Sodium Hypochlorite, should be used at a dilution ratio of 1 part bleach to 10 parts water.
RINSE OFF CORROSIVE CLEANERS
These products are NOT considered mild detergents. They are corrosive in nature and may cause damage to your stretcher mattress if used improperly. Mattresses must be rinsed with clean water and dried thoroughly after using corrosives such as quaternary, phenolic, or chlorine bleach. Failure to properly rinse and dry the mattress leaves a corrosive residue on the surface, likely causing premature corrosion.
Iodophor type disinfectants are not recommended for use because staining may result.
The following table lists the recommended cleaner types for each mattress cover material (see definitions below):
Vinyl Mattress Cover Polyurethane Mattress Cover
Recommended Phenolics Quaternary, Quat/Isopropyl
Acceptable Quaternary, Chlorine Bleach (1:10) Chlorine Bleach (1:10)
Not Recommended Quat/Isopropyl Phenolics
Quaternary Cleaners: identified by ingredients containing the phrase “…yl ammonium chloride” Quat/Isopropyl Cleaners: identified by a quaternary ingredient above plus isopropyl alcohol Phenolic Cleaners: identified by ingredients containing the suffix “-phenol” Chlorine Bleach: known generically as “Sodium Hypochlorite”
Return To Table of Contents
www.stryker.com 1037- 009-002 REV A 13
Page 14
Cleaning
MATTRESS CLEANING (CONTINUED)
SPECIAL INSTRUCTIONS
Velcro To clean and disinfect, saturate with disinfectant, rinse with water, and allow it to evaporate.
Soils or Stains Use neutral soaps and warm water. Do not use harsh cleansers, solvents or abrasive cleaners.
Hard-To-Clean Spots Use standard household/vinyl cleansers and a soft bristle brush on troublesome spots or
stains. Pre-soak heavy, dried-on soil.
Laundering Laundering is NOT RECOMMENDED. Laundering may substantially decrease the useful
life of the mattress.
DO NOT STEAM CLEAN, PRESSURE WASH, HOSE OFF OR ULTRASONICALLY CLEAN MATTRESSES. Using these methods of cleaning are not recommended and may void this product’s warranty.
REMOVAL OF IODINE STAINS
1. Make a solution of 1−2 tablespoons Sodium Thiosulfate in a pint of warm water and use it to wipe the stained area. Clean the stain as soon as possible after it occurs. If stains are not immediately removed, allow solution to soak or stand on the surface before wiping.
2. Rinse surfaces which have been exposed to the solution with clear water before returning mattress to service.
Note: Failure to follow the above directions when using these types of cleaners may void this product’s warranty.
Return To Table of Contents
14 10 37- 009-002 REV A www.stryker.com
Page 15

Preventative Maintenance

At a minimum, preventative maintenance should be performed annually. A preventative maintenance program should be established for all Stryker Medical equipment. Preventative maintenance may need to be performed more frequently based on the usage level of the product.
All fasteners secure
Siderails move and latch properly
Engage brake pedal and push on the stretcher to ensure all casters lock securely
Steer function working properly
All casters secure and swivel properly
Inspect each caster and remove any wax or debris which may have collected on the caster or braking
mechanism
Body restraints working properly
I.V. pole intact and operating properly
Oxygen bottle holder intact and operating properly
Fowler operating and latching properly
Trendelenburg/reverse Trendelenburg operating properly
No rips or cracks in mattress cover
Transfer boards intact and operating properly
Ground chain intact
No leaks at hydraulic connections
Hydraulic jacks hold properly
Hydraulic drop rate set properly
Hydraulic oil level sufficient
Lubricate where required
X-ray tray slide tracks cleaned of dust and debris
Accessories and mounting hardware in good condition and working properly
Product Serial Number:
Completed by: ____________________________________________ Date: _____________________
Return To Table of Contents
www.stryker.com 1037- 009-002 REV A 15
Page 16

Quick Reference Replacement Parts List

The parts and accessories listed on this page are all currently available for purchase. Some of the parts identified on the assembly drawing parts in this manual may not be individually available for purchase. Please call Stryker Customer Service USA at 1-800-327-0770 for availability and pricing.
Part Name Part Number
Big Wheel Assembly 1115 - 0 15 - 073
Big Wheel Timing Cam and Link Assembly 1040-003-035
Brake Cam and Link Assembly (Fifth Wheel) 0853-003-035
Caster Assembly 0853-503-020
Fifth Wheel Assembly 1105-006-130
Fowler Gas Cylinder 1010-031-078
Hydraulic Jack, Constant 0753-002-101
I.V. Pole, Standard, Removable 0390-025-000
Paint, Touch-Up, Gloss Black, Bottle with Brush 7000-001-322
Paint, Touch-Up, Gloss Black, Spray Can 7000-001-319
Paint, Touch-Up, White, Bottle with Brush 7000-001-147
Paint, Touch-Up, White, Spray Can 7000-001-148
Restraint Strap Package 0785-045-010
Restraint Strap, Ankle 0785-045-020
Restraint Strap, Body 0785-045-015
Restraint Strap, Wrist 0946-044-000
Siderail Pads 1010-052-000
Return To Table of Contents
16 1037-0 09-002 REV A www.stryker.com
Page 17

Service Information

CASTER ASSEMBLY REPLACEMENT

Tools Required:
• 1/2” Socket
• 3/8” Drive Ratchet
• Needle Nose Pliers
• Bungee Cords
• Small Bottle Jack
• 3/8” Drive Torque Wrench (ft-lb)
Procedure:
1. Pump the stretcher all the way up.
2. Raise both siderails to the up and latched position.
3. Using bungee cords, support the raised base hood.
4. Put the base brake/steer pedal in the neutral position.
5. Using a 1/2” socket, remove the two flange nuts (one on each side) that secure the timing link to the casters.
6. Using needle nose pliers, remove the rue clip and then the clevis pin from the brake rod activator.
7. Apply the brakes by moving the brake/steer pedal to the brake position.
8. Remove the brake timing link assembly by equally pulling outward on the timing link assembly. Save the brake timing link for reinstallation.
9. Using a small bottle jack, raise the stretcher up until the caster falls out of the frame socket. Discard the caster.
10. Install the new caster assembly by carefully and slowly lowering the jack down until the caster is secured in the base frame, and then remove the jack.
Note: Make sure that the arrow located at the top of the caster assembly fork stem points toward the foot end of the unit. If the arrow does not point toward the foot end, damage could occur to the caster assembly.
11. Reverse steps to reinstall. Torque the two flange nuts that secure the timing link assembly to the casters to 80 ± 20 ft-lb.
Note: When installing the new brake timing link assembly be sure to reinstall the bushing which may have fallen off during the removal of the old brake timing link assembly.
12. Verify proper operation of the unit before returning it to service.
Return To Table of Contents
www.stryker.com 1037- 009-002 REV A 17
Page 18
Service Information

BRAKE SWIVEL LOCK RING REPLACEMENT

Tools Required:
• 1/2” Socket
• 5/16” Socket
• 3/8” Drive Ratchet
• 1/4 ” R at c het
• Needle Nose Pliers
• Bungee Cords
• Small Bottle Jack
• 3/8” Drive Torque Wrench (ft-lb)
Procedure:
1. Pump the stretcher all the way up.
2. Raise both siderails to the up and latched position.
3. Using bungee cords, support the raised base hood.
4. Put the base brake/steer pedal in the neutral position.
5. Using a 1/2” socket, remove the two flange nuts (one on each side) that secure the timing link to the casters.
6. Using needle nose pliers, remove the rue clip, and then the clevis pin from the brake rod activator.
7. Apply the brakes by moving the brake/steer pedal to the brake position.
8. Remove the brake timing link assembly by equally pulling outward on the timing link assembly. Save the brake timing link for reinstallation.
9. Using a small bottle jack, raise the stretcher up until the caster falls out of the frame socket. Discard the caster.
10. Using a 5/16” socket, remove the two bolts that secure the brake swivel lock ring to the base frame and remove. Discard the brake swivel lock ring.
11. Using a 5/16” socket, install the new brake swivel lock ring.
Note: The brake swivel lock ring has two dowels that mate to the base frame when installing.
12. Install the new caster assembly by carefully and slowly lowering the jack down until the caster is secured in the base frame, and then remove the jack.
Note: Make sure that the arrow located at the top of the caster assembly fork stem points toward the foot end of the unit. If the arrow does not point toward the foot end, damage could occur to the caster assembly.
13. Reverse steps to reinstall. Torque the two flange nuts that secure the timing link assembly to the casters to 80 ± 20 ft-lb. Torque the two bolts that secure the brake swivel lock ring to the base frame to 50 ± 4 ft-lb.
Note: When installing the new brake timing link assembly be sure to reinstall the bushing which may have fallen off during the removal of the old brake timing link assembly.
14. Verify proper operation of the unit before returning it to service.
Return To Table of Contents
18 1037-0 09-002 REV A www.stryker.com
Page 19
Service Information

BRAKE TIMING LINK REPLACEMENT, HEAD END OR FOOT END

Tools Required:
• 1/2” Socket
• 3/8” Drive Ratchet
• Needle Nose Pliers
• Bungee Cords
• 3/8” Drive Torque Wrench (ft-lb)
Procedure:
1. Pump the stretcher all the way up.
2. Raise both siderails to the up and latched position.
3. Using bungee cords, support the raised base hood.
4. Put the base brake/steer pedal in the neutral position.
5. Using a 1/2” socket, remove the two flange nuts (one on each side) that secure the timing link assembly to the casters.
6. Using needle nose pliers, remove the rue clip and then clevis pin from the brake rod activator.
7. Apply the brakes by moving the brake/steer pedal to the brake position.
8. Remove the brake timing link assembly by equally pulling outward on the timing link assembly. Discard the brake timing link.
9. Reverse steps to reinstall. Torque the two flange nuts that secure the timing link assembly to the casters to 80 ± 20 ft-lb.
Note: When installing the new brake timing link assembly be sure to reinstall the bushing which may have fallen off during the removal of the old brake timing link assembly.
10. Verify proper operation of the unit before returning it to service.
Return To Table of Contents
www.stryker.com 1037- 009-002 REV A 19
Page 20
Service Information

BRAKE CAM ASSEMBLY REPLACEMENT

Tools Required:
• Needle Nose Pliers
• Bungee Cords
Procedure:
1. Pump the stretcher all the way up.
2. Raise both siderails to the up and latched position.
3. Using bungee cords, support the raised base hood.
4. Put the base brake/steer pedal in the neutral position.
5. Using needle nose pliers, remove the rue clip and clevis pin that secure the brake cam assembly to the brake rod. Save all parts for reinstallation.
6. Using needle nose pliers, remove the rue clip and washer from the top bearing pivot support. Save all parts for reinstallation.
7. Using needle nose pliers, remove the rue clip and plastic washer from the bottom support. Save the rue clip for reinstallation.
8. Raise the brake cam link off of the brake rod actuator and slowly pull outward on the brake cam assembly. Discard the brake cam assembly.
9. Reverse steps to reinstall.
Note: When installing the new brake cam assembly, install the bottom slightly first and then push downward and inward to install under the top bearing.
10. Verify proper operation of the unit before returning it to service.
Return To Table of Contents
20 1037- 009-002 REV A www.stryker.com
Page 21
Service Information

BRAKE ROD REPLACEMENT - FIFTH WHEEL ONLY

Tools Required:
• Hammer
• 7/32” #7 Roll Pin Punch
• Needle Nose Pliers
• Bungee Cords
Procedure:
1. Pump the stretcher all the way up.
2. Raise both siderails to the up and latched position.
3. Using bungee cords, support the raised base hood.
4. Put the brake/steer pedal into the steer position.
5. Using a hammer and a 7/32” roll pin punch, remove the eight roll pins from pedal to pedal on the brake rod.
6. Using needle nose pliers, remove the rue clip and clevis pin that secure the brake link to the brake rod.
7. Using your hands, grasp the brake rod and remove each brake/steer pedal. Save the pedals for reinstallation.
8. Remove the brake rod from the base.
9. Install the new brake rod and then install the roll pin into the head end timing link arm first.
10. Reverse steps to reinstall.
11. Verify proper operation of the unit before returning it to service.
Return To Table of Contents
www.stryker.com 1037- 009-002 REV A 21
Page 22
Service Information

BRAKE ROD REPLACEMENT - BIG WHEEL ONLY

Tools Required:
• Hammer
• 7/32” #7 Roll Pin Punch
• Needle Nose Pliers
• Bungee Cords
Procedure:
1. Pump the stretcher all the way up.
2. Raise both siderails to the up and latched position.
3. Using bungee cords, support the raised base hood.
4. Put the brake/steer pedal into the steer position.
5. Using a hammer and a 7/32” roll pin punch, remove the two roll pins from pedal to pedal on the brake rod.
6. Using needle nose pliers, remove the five rue clips and clevis pins from the brake rod. Save all parts for reinstallation.
Note: If the unit has four-sided brakes, there will be a sixth rue clip and clevis pin to remove.
7. Using a 5/32” Allen wrench, loosen the set screw on the head end brake rod stop collar.
8. Remove the brake rod from the base.
9. Reverse steps to install the new brake/steer pedal assembly.
10. Verify proper operation of the unit before returning it to service.
Return To Table of Contents
22 1037- 009-002 REV A www.stryker.com
Page 23
Service Information

FIFTH WHEEL ASSEMBLY REPLACEMENT

Tools Required:
• 1/2” Socket
• 3/8” Drive Ratchet
• Needle Nose Pliers
• Bungee Cords
• 3/8” Drive Torque Wrench (ft-lb)
Procedure:
1. Pump the stretcher all the way up.
2. Raise both siderails to the up and latched position.
3. Using bungee cords, support the raised base hood.
4. Using a 1/2” socket, remove the bolt that holds the fifth wheel cam drive link to the cam.
5. Using a 1/2” socket, remove the two bolts that secure the fifth wheel assembly to the base frame.
6. Using needle nose pliers, remove the pump pedal return spring from the fifth wheel bracket.
7. Using needle nose pliers, remove the foot end jack release rod from the release pedal.
8. Remove the release rod.
9. Working from the patients left side, rotate the fifth wheel assembly counter clockwise while lifting the fifth wheel assembly up and out.
10. Reverse steps to reinstall. Torque all bolts to 13 ± 2 ft-lb.
11. Verify proper operation of the unit before returning it to service.
Return To Table of Contents
www.stryker.com 1037- 009-002 REV A 23
Page 24
Service Information

JACK REPLACEMENT, HEAD END - FIFTH WHEEL ONLY

Tools Required:
• 1/2” Socket with Extension
• 3/8” Drive Ratchet
• 3/8” Drive Torque Wrench (ft-lb)
Procedure:
1. Remove the litter from the stretcher. See “Litter Top Removal” on page 29.
2. Using a 1/2” socket with extension and a 3/8” drive ratchet, remove the two hex head screws that hold the jack base to the stretcher base frame. When reinstalling, torque the screws to 11 ± 5 ft-lb.
3. Remove the two hex head screws that hold the jack reservoir clamp to the base frame and remove the clamps.
4. Lift straight up on the pump connecting rod and disconnect the pump piston from the connecting rod. When reinstalling, torque the screws to 13 ± 2 ft-lb.
5. Disconnect the pump pedal swivel from the release pedal mounting plate.
6. Remove the head end release rod from the release valve assembly.
7. Using a 1/2” socket with extension, remove the two hex head screws that hold the jack base to the stretcher base frame. When reinstalling, torque the screws to 13 ± 2 ft-lb.
8. Remove the jack assembly.
9. To reinstall the jack, install the bolts on the jack and reservoir clamp but do not tighten them fully.
10. Reinstall the pump connecting rod and release rod.
11. Depress the pump pedal fully (to the floor). This will properly locate the jack onto the base frame.
12. Tighten the bolts on the jack and reservoir clamp. Torque all bolts to 13 ± 2 ft-lb.
13. With the assistance of another person, reinstall the litter top onto the jack shafts.
14. Torque the hex head screws on the support tube weldments to 11 ± 5 ft-lb.
15. Pump up the litter and apply weight to verify the jacks hold and do not drift.
16. Verify proper operation of the unit before returning it to service.
Note: The jack descent rate is set at the factory and adjustment is not recommended.
Return To Table of Contents
24 1037- 009-002 RE V A www.stryker.com
Page 25
Service Information

JACK REPLACEMENT, HEAD END - BIG WHEEL ONLY

Tools Required:
• 1/2” Socket with Extension
• 3/8” Drive Ratchet
• 3/8” Drive Torque Wrench (ft-lb)
Procedure:
1. Remove the litter from the stretcher. See “Litter Top Removal” on page 29.
2. Using a 1/2” socket with extension and a 3/8” drive ratchet, remove the two hex head screws that hold the jack base to the stretcher base frame.
3. Remove the two hex head screws that hold the jack reservoir clamp to the base frame and remove the clamps.
4. Lift straight up on the pump connecting rod and disconnect the pump piston from the connecting rod.
5. Disconnect the release pedal swivel from the release pedal weldment.
6. Remove the head end release rod from the release valve assembly.
7. Using a 1/2” socket with extension, remove the two hex head screws that hold the jack base to the stretcher base frame.
8. Lift out the jack assembly.
9. To reinstall the jack, install the bolts on the jack and reservoir clamp but do not tighten them fully.
10. Reinstall the pump connecting rod and release rod.
11. Depress the pump pedal fully (to the floor). This will properly locate the jack onto the base frame.
12. Tighten the bolts on the jack and reservoir clamp. Torque all bolts to 13 ± 2 ft-lb.
13. Pump up the litter and apply weight to verify the jacks hold and do not drift.
Note: The jack descent rate is set at the factory and adjustment is not recommended.
Return To Table of Contents
www.stryker.com 1037- 009-002 REV A 25
Page 26
Service Information

JACK REPLACEMENT, FOOT END - FIFTH WHEEL ONLY

Tools Required:
• 1/2” Socket with Extension
• 3/8” Drive Ratchet
• Pliers
• 3/8” Drive Torque Wrench (ft-lb)
Procedure:
1. Remove the litter from the stretcher. See “Litter Top Removal” on page 29.
2. Lift the base hood off of the base frame.
3. Using a 1/2” socket with extension, remove the two hex washer head screws and washers that connect the pump pedal link to the foot end pump pedal assembly and pump connecting rod.
4. Remove the foot end release rod from the release valve on the jack assembly by disconnecting the release pedal swivel from the pins on the release pedal weldment.
5. Disconnect the jack pump piston from the pump connecting rod.
6. Using a 1/2” socket with extension, remove the two hex washer head screws that hold the reservoir clamp.
7. Remove the jack assembly.
8. To reinstall the jack, install the bolts on the jack and reservoir clamp but do not tighten them fully.
9. Reinstall the pump connecting rod and release rod.
10. Depress the pump pedal fully (to the floor). This will properly locate the jack onto the base frame.
11. Tighten the bolts on the jack and reservoir clamp. Torque all bolts to 13 ± 2 ft-lb.
12. With the assistance of another person, reinstall the litter top onto the jack shafts.
13. Torque the hex head screws on the support tube weldments to 11 ± 5 ft-lb.
14. Pump up the litter and apply weight to verify the jacks hold and do not drift.
15. Verify proper operation of the unit before returning it to service.
Note: The jack descent rate is set at the factory and adjustment is not recommended.
Return To Table of Contents
26 1037-0 09-002 REV A www.stryker.com
Page 27
Service Information

JACK REMOVAL, FOOT END - BIG WHEEL BASE WITH THREE-SIDED CONTROLS

Tools Required:
• 1/2” Socket with Extension
• 3/8” Drive Ratchet
• 3/8” Drive Torque Wrench (ft-lb)
Procedure:
1. Remove the litter from the stretcher. See “Litter Top Removal” on page 29.
1. Lift the base hood off of the base frame.
2. Remove the hair pin cotter and washer that connect the Big Wheel side control linkage toggle pivot plates to the Big Wheel side control carriage weldment.
3. Remove the rue ring cotter and clevis pin that connect the Big Wheel side control rod end link to the yolk weldment on the end control brake rod.
4. Remove the Big Wheel carriage assembly.
5. Remove the two hex washer head screws and washers that connect the pump pedal link to the foot end pump pedal assembly and pump connecting rod.
6. Remove the foot end pump pedal return spring.
7. Remove the cotter pin from the center of the foot end pump pedal assembly and slide out the pivot pin.
8. Slide the foot end pump pedal assembly up and over the foot end mounting bracket.
9. Remove the four hex washer head screws that fasten the foot end mounting bracket to the base frame and set the bracket aside.
10. Remove the foot end release rod from the release valve on the jack assembly by dislodging the release pedal swivel from the pins on the release pedal weldment.
11. Dislodge the jack pump piston from the pump connecting rod.
12. Remove the two hex washer head screws that hold the reservoir clamp in place.
13. Remove the jack assembly.
14. Reverse steps to reinstall. Torque all bolts to 13 ± 2 ft-lb.
15. Verify proper operation of the unit before returning it to service.
Note: The jack descent rate is set at the factory and adjustment is not recommended.
Return To Table of Contents
www.stryker.com 1037- 009-002 REV A 27
Page 28
Service Information

RELEASE PEDAL (SIDE) ADJUSTMENT

Tools Required:
• None
Procedure:
1. Manually disengage the release pedal swivel from the release pedal assembly.
2. To increase the release rod engagement with the release valve, turn the release pedal swivel clockwise on the threaded release rod.
3. To decrease the release rod engagement with the release valve, turn the release pedal swivel counterclockwise on the threaded release rod.
Note: If the pedal swivel assembly is threaded too far onto the release rod, the release valve will be partially activated and the jack will drift.
Return To Table of Contents
28 1037-0 09-002 REV A ww w.stryker.com
Page 29
Service Information

LITTER TOP REMOVAL

Tools Required:
• 1/2” Socket with Extension
• 3/8” Drive Ratchet
• Standard Screwdriver
• 3/8” Drive Torque Wrench (ft-lb)
• 7/16”-20 Bolt
Procedure:
1. Using the foot pedal, pump the litter top all the way up.
2. Remove the stretcher mattress.
3. Using a 1/2” socket and a 3/8” drive ratchet, remove the truss head screws that hold the jack support tubes to the jack shafts. When reinstalling, torque the truss head screws to 23 ± 3 ft-lb.
4. Insert a fine-thread 7/16”-20 bolt far enough into the top of the jack supports to separate the litter top from the jack shaft.
5. With the assistance of another person, lift the litter straight up to remove it from the jack shafts and set it aside.
6. Reverse steps to reinstall the litter.
7. Verify proper operation of the unit before returning it to service.
Return To Table of Contents
www.stryker.com 1037- 009-002 REV A 29
Page 30
Service Information

TRANSFER BOARD COUNTERBALANCE ADJUSTMENT

Tools Required:
• 7/16” Combination Wrench
Procedure:
1. Raise the transfer board to the full up position.
2. Unhook the extension spring at the eye bolt.
3. Using a 7/16” combination wrench, loosen the jam nut at the eye bolt.
4. Adjust the eye bolt to the desired position.
5. Tighten the jam nut.
6. Hook the extension spring to eye bolt.
7. Allow the transfer board to lower on its own.
8. Repeat steps until the desired counterbalance is achieved.

FOLD DOWN SIDERAIL LATCH ADJUSTMENT

Tools Required:
• 1/8” Hex Allen Wrench
WARNING
The siderail latches are preset at the factory, and do not normally need adjustment. If adjustment must be done, it is important to follow the procedure below. If adjustment is not done properly, injury to the patient or user could result.
Procedure:
1. Using a 1/8” hex Allen wrench, adjust the hex Allen screw located on the latch assembly opposite the latch. Turning the screw clockwise will decrease the amount of “play” in the latching mechanism. Turning counterclockwise will
increase the amount.
Note: The amount of “play” in the siderail, when in full up engaged position, should be approximately 1/8” to 3/16”
inches.
CAUTION
Too much “play” when the siderail is in the full up engaged position will give the siderail the appearance of being unstable and could also cause premature wearing of the latch system.
Too little “play” will obstruct the latch and keep it from engaging completely in the full up position, which may result in damage to the latch and/or injury to the patient or user.
Return To Table of Contents
30 1037- 009 -002 RE V A www.stryker.com
Page 31
Service Information

RELEASE PEDAL REPLACEMENT, FOOT END

Tools Required:
• Needle-Nose Pliers
Procedure:
1. Apply the stretcher brakes.
2. Disconnect the release pedal return springs from the foot end release pedals.
3. Remove the rue ring cotters and the clevis pins that connect the foot end release pedals to the mounting bracket.
4. Rotate the pedals upward.
5. Remove the rue ring cotters that connect the head end and foot end release rods to the foot end release pedals and remove the pedals.
6. Reverse steps to install the new pedals.
7. Verify proper operation of the unit before returning it to service.

RELEASE PEDAL ROD REMOVAL, FOOT END

Tools Required:
• Needle-Nose Pliers
Procedure:
1. Remove the foot end release pedal. See “Release Pedal Replacement, Foot End” on page 31.
2. Remove the snap in nyliners that hold the foot end pedal release rods into the pedal mounting bracket.
3. Unsnap the foot end pedal release rods from the white plastic release rod brackets.
4. Dislodge the side control release pedal swivels from the studs on the side control release pedal weldment.
5. Remove the foot end pedal release rods.
6. Reverse steps to reinstall the pedal rods.
7. Verify proper operation of the unit before returning it to service.
Return To Table of Contents
www.stryker.com 1037- 009-002 REV A 31
Page 32
Service Information

BIG WHEEL REMOVAL (NON FOUR-SIDED BRAKES)

Tools Required:
• Large Standard Screwdriver
• Small Standard Screwdriver
• Bungee Cords
Procedure:
1. Lift the base hood and separate the Velcro that holds the base hood to the base frame. Support the hood from the litter using bungee cords so it is out of the way.
2. Using a large standard screwdriver, remove the hub cap in the center of the wheel.
3. Using a small standard screwdriver, remove the spiral retaining ring from the groove on the wheel axle.
4. Remove the Big Wheel.
5. Reverse steps to reinstall the Big Wheel.
6. Verify proper operation of the unit before returning it to service.

BIG WHEEL REMOVAL (FOUR-SIDED BRAKES)

Tools Required:
• Large Standard Screwdriver
• 7/32” Roll Pin Punch
• Bungee Cords
Procedure:
1. Lift the base hood and separate the Velcro that holds the base hood to the base frame. Support the hood from the litter using bungee cords so it is out of the way.
2. Using a large standard screwdriver, remove the hub cap in the center of the wheel.
3. Using a 7/32” roll pin punch, remove the tapered groove pin from the pedal.
Note: The pin is tapered, so it must be driven from the bottom up.
4. Remove the Big Wheel.
5. Reverse steps to reinstall the Big Wheel.
6. Verify proper operation of the unit before returning it to service.
Return To Table of Contents
32 1037-0 09-002 REV A www.stryker.com
Page 33
Service Information

BIG WHEEL DAMPENER REPLACEMENT

Tools Required:
• Bungee Cords
• Needle Nose Pliers
• Standard Screwdriver
• 3/8” Drive Torque Wrench (ft-lb)
• 7/16”-20 Bolt
Procedure:
1. Pump the stretcher all the way up.
2. Raise the left and right siderails to the up and latched position.
3. Using bungee cords, raise the base hood and support.
4. Put the unit into neutral.
5. Using needle nose pliers, remove the big wheel drive link rue clip and clevis pin from the lift cam and flip the lift cam out of the way.
6. Using needle nose pliers, remove the rue clip and clevis pin from the gas cylinder.
7. Using your hand, grab the lift cam and pull it upward with the gas cylinder.
8. Using needle nose pliers, remove the rue clip and clevis pin from the dampener arm.
9. Using needle nose pliers, remove the rue clip and washer and discard the gas cylinder.
10. Reverse the above steps for installation of the new brake timing link.
11. Verify proper operation of the unit before returning it to service.
Return To Table of Contents
www.stryker.com 1037- 009-002 REV A 33
Page 34
Service Information

PNEUMATIC FOWLER ADJUSTMENT

Tools Required:
• 5/32” Allen Wrench
• 1/2” Combination Wrench
Procedure:
1. Raise the fowler to 75 degrees or higher.
2. Using a 1/2” combination wrench, loosen the hex nuts in the actuator arms on the end of the trip bar.
3. To adjust the fowler, use a 5/32” hex Allen wrench to turn the Allen screws counter-clockwise or clockwise. If the fowler will not move, turn the screws 1 to 2 turns counter−clockwise. If the fowler will not holds its position, turn the screws 1 to 2 turns clockwise.
4. Retighten the hex nuts. Make sure that the fowler travels from flat up to 90 degrees and down again and that it holds its position when weight is applied before returning the stretcher to service.
5. Verify proper operation of the unit before returning it to service.
Return To Table of Contents
34 1037-0 09-002 REV A www.stryker.com
Page 35
Service Information

REMOVAL OF EXCESS AIR FROM THE HYDRAULIC SYSTEM

Tools Required:
• None
Procedure:
1. Verify that all hydraulic linkages are secure and operating properly.
2. Raise the litter to its highest height.
3. Continue to pump the pedal several times to force the air through the system.
4. Verify proper operation before returning the unit to service.
Return To Table of Contents
www.stryker.com 1037- 009-002 REV A 35
Page 36

Fifth Wheel Standard Brake Assembly

1105-003-205 Rev A (Reference Only)
Torque item H
to 19 ± 4 ft-lb
Torque item A
to 50 ± 4 in-lb.
Torque item J to 19 ± 4 ft-lb
Torque item F
to 80 ± 20 in-lb.
Torque item F
to 80 ± 20 in-lb.
Torque item F
to 80 ± 20 in-lb.
Torque item F
to 80 ± 20 in-lb.
Return To Table of Contents
36 1037- 009-002 RE V A www.stryker.com
Page 37
Fifth Wheel Standard Brake Assembly
Torque item E to 40 ± 6 ft-lb
Torque item G
to 13 ± 2 ft-lb
Torque item G
to 13 ± 2 ft-lb
Return To Table of Contents
www.stryker.com 1037- 009-002 REV A 37
Page 38
Fifth Wheel Standard Brake Assembly
Fifth Wheel Standard Brake Assembly - 1105-003-205 Rev A (Reference Only)
Item Part No. Part Name Qty.
A 0003-147-000 Hex Washer Head Screw 8 B 0003-364-000 Hex Washer Head Truss Screw 1 C 0011-263-000 Washer 2 D 0013-018-000 External Tooth Lock Washer 1 E 0016-049-000 Nylock Hex Nut 2 F 0016-135-000 Nylock Flange Hex Nut 4 G 0023-288-000 Hex Washer Head Screw 4 H 0023-330-000 Hex Washer Head Screw 4 J 0023-331-000 Hex Washer Head Screw 4 K 0026-295-000 Clevis Pin 1 L 0026-393-000 Clevis Pin 2 M 0027-019-000 Rue Ring Cotter 2 N 0027-020-000 Rue Ring Cotter 3 P 0853-003-035 Brake Cam and Link Assembly 1 R 0853-003-064 Brake Rod Crank Cap 2 T 0853-003-075 Timing Cam Bearing Assembly 1 U 0853-003-103 Timing Cam Spring Retainer 1 V 0853-003-104 Fifth Wheel Timing Cam Spring 1 W 0853-003-131 Timing Cam Spacer 2 Y 1105-005-087 Return Spring Hook 1 AA 0853-102-003 Caster Steer Lock Gear 4 AB 0853-102-004 Stepped Flange Bearing 8 AC 0853-203-201 Brake Rod Assembly (page 39) 1 AD 0853-203-230 Bearing Pivot Support 2 AE 0853-303-010 Brake Link Assembly, Head End 1 AF 0853-303-020 Brake Link Assembly, Foot End 1 AG 0853-401-001 Base Weldment 1 AH 3001-200-052 Grounding Chain 1 AJ 0014-003-000 Washer 1
Return To Table of Contents
38 1037- 009 -002 RE V A www.stryker.com
Page 39

Fifth Wheel Brake Rod Assembly

0853-203-201 Rev B (Reference Only)
Item Part No. Part Name Qty.
A 0026-014-000 Slotted Spring Pin 7 B 0026-251-000 Clevis Pin 1 C 0027-020-000 Rue Ring Cotter 1 D 0753-003-015 Brake Rod Nyliner 4 E 0853-003-004 Brake Rod Support 4 F 0853-003-055 Fifth Wheel Timing Cam Crank Assy 1 G 0853-203-011 Brake Activation Crank 2 H 0853-206-135 Fifth Wheel Drive Link Assy (page 40) 1 J 0853-303-014 Brake Rod 1 K 1105-001-335 Label, Brake (Red) 2 L 1105-001-336 Label, Steer (Green) 2
Return To Table of Contents
www.stryker.com 1037- 009-002 REV A 39
Page 40

Fifth Wheel Drive Link Assembly - 0853-206-135

Rev E
Item Part No. Part Name Qty.
A 0753-003-098 Rivet 1 B 0853-206-011 Brake Rod Drive Link 1 C 0853-206-022 Fifth Wheel Cam Drive Link 1 D 0853-206-047 Fifth Wheel Cam Drive Link 1
Return To Table of Contents
40 1037- 009-002 REV A www.stryker.com
Page 41

Fifth Wheel Side Control Brake Assembly

1105-003-220 Rev A (Reference Only)
Torque item H
to 19 ± 4 ft-lb
Torque item A
to 50 ± 4 in-lb.
Torque item F
to 80 ± 20 in-lb.
Torque item J to 19 ± 4 ft-lb
Torque item F
to 80 ± 20 in-lb.
Torque item F
to 80 ± 20 in-lb.
Torque item F
to 80 ± 20 in-lb.
Return To Table of Contents
www.stryker.com 1037- 009-002 REV A 41
Page 42
Fifth Wheel Side Control Brake Assembly
Torque item E
to 40 ± 6 ft-lb
Torque item G
to 13 ± 2 ft-lb
Torque item G
to 13 ± 2 ft-lb
Return To Table of Contents
42 1037- 009-002 REV A www.stryker.com
Page 43
Fifth Wheel Side Control Brake Assembly
Torque item G
to 13 ± 2 ft-lb
Return To Table of Contents
www.stryker.com 1037- 009-002 REV A 43
Page 44
Fifth Wheel Side Control Brake Assembly
Fifth Wheel Side Control Brake Assembly - 1105-003-220 Rev A (Reference Only)
Item Part No. Part Name Qty.
A 0003-147-000 Hex Washer Head Screw 8 B 0003-364-000 Hex Washer Head Truss Screw 1 C 0011-263-000 Washer 2 D 0013-018-000 External Tooth Lock Washer 1 E 0016-049-000 Nylock Hex Nut 2 F 0016-135-000 Nylock Flange Hex Nut 4 G 0023-288-000 Hex Washer Head Screw 8 H 0023-330-000 Hex Washer Head Screw 4 J 0023-331-000 Hex Washer Head Screw 4 K 0026-295-000 Clevis Pin 1 L 0026-340-000 Clevis Pin 1 M 0026-393-000 Clevis Pin 2 N 0027-019-000 Rue Ring Cotter 2 P 0027-020-000 Rue Ring Cotter 4 R 0853-003-035 Brake Cam and Link Assembly 1 T 0853-003-064 Brake Rod Crank Cap 2 U 0853-003-075 Timing Cam Bearing Assembly 1 V 0853-003-103 Timing Cam Spring Retainer 1 W 0853-003-104 Fifth Wheel Timing Cam Spring 1 Y 0853-003-131 Timing Cam Spacer 2 AA 1105-005-087 Return Spring Hook 1 AB 0853-102-003 Caster Steer Lock Gear 4 AC 0853-102-004 Stepped Flange Bearing 8 AD 0853-203-225 Brake Rod/Side Control Assembly (page 45) 1 AE 0853-203-230 Bearing Pivot Support 2 AF 0853-303-010 Brake Link Assembly, Head End 1 AG 0853-303-020 Brake Link Assembly, Foot End 1 AH 0853-401-001 Base Weldment 1 AJ 1105-003-210 Side Control Brake Assembly (page 46) 1 AK 3001-200-052 Grounding Chain 1 AL 0014-003-000 Washer 1
Return To Table of Contents
44 1037- 009 -002 REV A www.stryker.com
Page 45

Fifth Wheel Brake Rod/Side Control Assembly

0853-203-225 Rev B (Reference Only)
Item Part No. Part Name Qty.
A 0026-014-000 Slotted Spring Pin 8 B 0026-251-000 Clevis Pin 1 C 0027-020-000 Rue Ring Cotter 1 D 0753-003-015 Brake Rod Nyliner 4 E 0753-003-112 Side Control Link 1 F 0853-003-004 Brake Rod Support 4 G 0853-003-055 Fifth Wheel Timing Cam Crank Assy 1 H 0853-203-011 Brake Activation Crank 2 J 0853-206-135 Fifth Wheel Drive Link Assy (page 40) 1 K 0853-303-014 Brake Rod 1 L 1105-001-335 Label, Brake (Red) 2 M 1105-001-336 Label, Steer (Green) 2
Return To Table of Contents
www.stryker.com 1037- 009-002 REV A 45
Page 46

Fifth Wheel Side Control Brake Assembly

1105-003-210 Rev A (Reference Only)
Item Part No. Part Name Qty.
A 0026-014-000 Slotted Spring Pin 3 B 0026-138-000 Grooved Pin 1 C 0026-340-000 Clevis Pin 1 D 0027-020-000 Rue Ring Cotter 1 E 0753-003-112 Side Control Link 1 F 0753-003-117 Rod End Link 1 G 0853-003-214 Side Control Shaft Support 1 H 1105-001-335 Label, Brake (Red) 2 J 1105-001-336 Label, Steer (Green) 2 K 1105-003-319 Side Control Brake Rod 1 L 1105-005-154 Butterfly “V” Pedal 2
Return To Table of Contents
46 1037- 009-002 REV A www.stryker.com
Page 47

Bumper Color Options - Individual or Set of Four

0853-003-085 Rev E (Reference Only)
Item Part No. Part Name Qty.
A 0853-003-082 Bumper 1
Bumper Color Individual Part Number Qty
Yellow 0853-003-551 1
Cool Grey 0853-003-552 1
Powder Blue 0853-003-553 1
Red 0853-003-554 1
Navy 0853-003-555 1
Dark Lilac 0853-003-556 1
Bumper Color Set of Four Part Number Qty
Yellow 1105-003-551 4
Cool Grey 1105-003-552 4
Powder Blue 1105-003-553 4
Red 1105-003-554 4
Navy 1105-003-555 4
Dark Lilac 1105-003-556 4
Return To Table of Contents
www.stryker.com 1037- 009-002 REV A 47
Page 48

8” Caster with Full Cover Assembly - 0853-503-020

Torque item B
to 9 ± 2 ft-lb
Rev B
Item Part No. Part Name Qty.
A 0003-099-000* Hex Head Cap Screw 1 B 0016-060-000* Toplock Hex Jam Nut 1 C 0023-330-000 Head Washer Head Screw 2 D 0026-377-000* Clevis Pin 1 E 0027-020-000* Rue Ring Cotter 1 F 0038-596-000* Compression Wire 1 G 0753-103-215* Molded Wheel Assembly 1 H 0853-003-032* Label, Caster Brake Pad 1 J 0853-003-040* Cam Housing Assembly 1 K 0853-003-046 Caster Cover - Right 1 L 0853-003-047 Caster Cover - Left 1 M 0853-003-048 Caster Cover Plug 2 N 0853-203-030* Brake Pad Assembly 1 P 0853-303-021* Caster Horn Assembly 1
* Shown for reference only. Individual part components are not available for sale.
Return To Table of Contents
48 1037- 009-002 REV A w ww.stryker.com
Page 49

Retractable Fifth Wheel Assembly

1105-006-110 Rev A (Reference Only)
Torque item A
to 13 ± 2 ft-lb
Torque item A
to 13 ± 2 ft-lb
Torque item B
to 13 ± 2 ft-lb
Item Part No. Part Name Qty.
A 0023-288-000 Hex Washer Head Screw 2 B 0023-305-000 Hex Washer Head Screw 1 C 0753-006-148 Cam Bearing 1 D 1105-006-130 Fifth Wheel Assembly (page 50) 1
Return To Table of Contents
www.stryker.com 1037- 009-002 REV A 49
Page 50
Torque item D
to 13 ± 2 ft-lb

Fifth Wheel Assembly - 1105-006-130

Rev A
Torque item D
to 13 ± 2 ft-lb
Torque item D
to 13 ± 2 ft-lb
Torque item AJ
to 13 ± 2 ft-lb
Torque item Y
to 80 ± 15 in-lb
Torque item D
to 13 ± 2 ft-lb
Return To Table of Contents
50 1037- 009-002 RE V A www.stryker.com
Page 51
Fifth Wheel Assembly - 1105-006-130
Item Part No. Part Name Qty.
A 0003-083-000 Hex Head Cap Screw 1 B 0011-360-000 Washer 2 C 0016-035-000 Nylock Hex Nut 1 D 0023-288-000 Hex Washer Head Screw 4 E 0025-050-000 Dome Head Rivet 2 F 0029-007-000 Dual Lock 1 G 0029-009-000 Dual Lock 1 H 0753-006-074 Torsion Spring 1 J 0753-006-075 Torsion Spring 1 K 0753-006-097 Drive Shaft Bearing 2 L 0753-006-106 Dampener 1 M 0753-006-108 Thrust Washer 1 N 0753-006-115 Bearing Race 2 P 0753-006-120 Bumper Mounting Pin 1 R 0753-006-133 Cam Pivot Block 1 T 0753-006-142 Fifth Wheel Cam 1 U 0753-006-143 Cam Bearing 1 V 0753-006-149 Fifth Wheel Ramp 1 W 0753-006-152 Spring Spacer 1 Y 0753-006-153 Roller Stem 1 AA 0753-006-198 Drive Pin 1 AB 0753-006-223 Drive Shaft 1 AC 0753-006-277 Roller 1 AD 1105-006-126 Fifth Wheel Bracket 1 AE 1105-006-131 Fifth Wheel Weldment 1 AF 0853-006-227 Return Spring Hook 1 AG 0853-010-045 Hood Standoff 1 AH 1210-001-147 Wheel 1 AJ 0023-160-000 Hex Washer Head Screw 1 AK 0853-006-011 Link Stop Plate 1
Return To Table of Contents
www.stryker.com 1037- 009-002 REV A 51
Page 52

Fifth Wheel Dual Sided Hydraulics Assembly

1105-005-500 Rev C (Reference Only)
Torque item C
to 13 ± 2 ft-lb
Return To Table of Contents
52 103 7-0 09-002 REV A ww w.stryker.com
Page 53
Fifth Wheel Dual Sided Hydraulics Assembly
Torque item C
to 13 ± 2 ft-lb
Torque item C
to 13 ± 2 ft-lb
Torque item C
to 13 ± 2 ft-lb
Fifth Wheel Dual Sided Hydraulics Assembly - 1105-005-500 Rev C (Reference Only)
Item Part No. Part Name Qty.
A 0011-023-000 Washer 2 B 0014-071-000 Washer 2 C 0023-288-000 Hex Washer Head Screw 8 D 0027-020-000 Rue Ring Cotter 2 E 0027-031-000 Hair Pin Cotter 1 F 0052-909-000 Clevis Joint 2 G 0753-005-044 Pump Pedal Bushing 2 H 0753-005-089 Pump Ram Plug 2 J 0853-005-009 Return Spring 3 K 0853-005-074 Pivot Pin 1 L 0853-010-215 Release Rod Bracket 2 M 1105-004-015 Release Rod, Foot End 1 N 1105-004-201 Lowering Pedal Assembly (page 54) 1 P 1105-005-035 Pump Connecting Tube Weldment 1 R 1105-005-075 Pump Pedal Link 1 T 1105-005-285 Pump Pedal Assy, Head End (page 55) 1 U 0853-204-014 Release Rod, Head End 1
www.stryker.com 1037- 009-002 REV A 53
Return To Table of Contents
Page 54

Lowering Pedal Assembly - 1105-004-201

Rev A
Item Part No. Part Name Qty.
A 0025-133-000 Dome Head Rivet 6 B 0753-004-029 Release Pedal Standoff 6 C 0853-004-320 Release Pedal Support 2 D 1105-004-004 Release Pedal Weldment 2 E 1105-201-127 Short Uni-Pedal 2
Return To Table of Contents
54 1037-0 09-002 REV A www.stryker.com
Page 55

Pump Pedal Assembly, Head End - 1105-005-285

Rev B
Item Part No. Part Name Qty.
A 0026-343-000 Groove Pin 2 B 0715-001-140 Vinyl Tube 1 C 1105-105-180 Pump Pedal Weldment, Head End 1 D 1105-201-126 Pump Pedal 2
Return To Table of Contents
www.stryker.com 1037- 009-002 REV A 55
Page 56
0853-102-025 Rev A (Reference Only)

Constant Descent Jack

Torque item A to 13 ± 2 ft-lb
Torque item A to 13 ± 2 ft-lb
Torque item A to 13 ± 2 ft-lb
Item Part No. Part Name Qty.
A 0023-288-000 Hex Washer Head Screw 8 B 0753-002-101 Constant Descent Jack Assembly 2 C 0853-010-007 Reservoir Clamp 2
Return To Table of Contents
56 1037- 009-002 REV A www.stryker.com
Page 57
Big Wheel Standard Base Assembly
1115-015-305 Rev B (Reference Only)
Torque item A
to 18 ± 3 ft-lb
Torque item A
to 18 ± 3 ft-lb
Return To Table of Contents
www.stryker.com 1037- 009-002 REV A 57
Page 58
Big Wheel Standard Base Assembly
Return To Table of Contents
58 1037- 009-002 RE V A www.stryker.com
Page 59
Big Wheel Standard Base Assembly
Big Wheel Standard Base Assembly - 1115-015-305 Rev B (Reference Only)
Item Part No. Part Name Qty.
A 0003-381-000 Head Washer Head Truss Screw 2 B 0021-166-000 Set Screw 1 C 0026-067-000 Slotted Spring Pin 2 D 0026-251-000 Clevis Pin 6 E 0026-295-000 Clevis Pin 1 F 0026-393-000 Clevis Pin 2 G 0027-020-000 Rue Ring Cotter 9 K 0042-020-000 Collar 1 L 0853-003-064 Brake Rod Crank Cap 2 M 0853-203-011 Brake Activation Crank 2 N 1040-203-113 Brake Rod 1 P 1040-003-013 Timing Cam Hard Stop 1 R 1040-003-015 Big Wheel Timing Cam Crank Assembly 1 T 1040-115-007 Carriage Pivot Bushing 2 U 1040-215-201 Big Wheel Carriage Assembly (page 65) 1 V 1105-001-335 Label, Brake (Red) 2 W 1105-001-336 Label, Steer (Green) 2 Y 1105-005-154 Butterfly “V” Pedal 2 AA 1115-003-405 Standard Brake Assembly (page 60) 1 AB 1115-005-500 Big Wheel Dual Sided Hydraulics (page 66) 1 AC 1210-201-251 Celcon Insert 1
Return To Table of Contents
www.stryker.com 1037- 009-002 REV A 59
Page 60

Big Wheel Standard Brake Assembly

1115-003-405 Rev B (Reference Only)
Torque item H
to 19 ± 4 ft-lb
Torque item A to 50 ± 4 ft-lb
Torque item J to 19 ± 4 ft-lb
Torque item F to
80 ± 20 in-lb.
Torque item F to
80 ± 20 in-lb.
Torque item F to
80 ± 20 in-lb.
Torque item F to
80 ± 20 in-lb.
Return To Table of Contents
60 1037- 009 -002 REV A www.stryker.com
Page 61
Big Wheel Standard Brake Assembly
Torque item E to 40 ± 6 ft-lb
Torque item G
to 13 ± 2 ft-lb
Return To Table of Contents
www.stryker.com 1037- 009-002 REV A 61
Page 62
Big Wheel Standard Brake Assembly
Big Wheel Standard Brake Assembly - 1115-003-405 Rev B (Reference Only)
Item Part No. Part Name Qty.
A 0003-147-000 Hex Washer Head Screw 8 B 0003-364-000 Hex Washer Head Truss Screw 1 C 0011-263-000 Washer 2 D 0013-018-000 External Tooth Lock Washer 1 E 0016-049-000 Nylock Hex Nut 2 F 0016-135-000 Nylock Flange Hex Nut 4 G 0023-288-000 Hex Washer Head Screw 4 H 0023-330-000 Hex Washer Head Screw 4 J 0023-331-000 Hex Washer Head Screw 4 K 0026-330-000 Clevis Pin 1 L 0027-019-000 Rue Ring Cotter 2 M 0027-020-000 Rue Ring Cotter 1 R 0052-015-000 Spacer 1 T 0081-330-000 Radial Bearing 1 U 0853-003-075 Timing Cam Bearing Assembly 1 V 0853-003-103 Timing Cam Spring Retainer 1 W 0853-003-104 Fifth Wheel Timing Cam Spring 1 Y 0853-003-031 Timing Cam Spacer 2 AA 0853-102-003 Caster Steer Lock Gear 4 AB 0853-102-004 Stepped Flange Bearing 8 AC 0853-203-230 Bearing Pivot Support 2 AD 1040-003-035 Big Wheel Timing Cam and Link Assy 1 AE 1115-006-201 Big Wheel Cam Bracket Assy (page 63) 1 AF 1040-006-231 Drive Arm 1 AG 1040-101-501 Base Weldment 1 AH 1040-103-010 Brake Link Assembly, Head End 1 AJ 1040-103-020 Brake Link Assembly, Foot End 1 AK 1210-201-251 Celcon Insert 3 AL 3001-200-052 Grounding Chain 1 AM 0014-003-000 Washer 1
Return To Table of Contents
62 1037-0 09-002 REV A www.stryker.com
Page 63

Big Wheel Cam Bracket Assembly - 1115-006-201

Rev D
Return To Table of Contents
www.stryker.com 1037- 009-002 REV A 63
Page 64
Big Wheel Cam Bracket Assembly - 1115-006-201
Item Part No. Part Name Qty.
A 0014-004-000 Washer 1 B 0014-063-000 Washer 2 C 0026-262-000 Clevis Pin 2 D 0026-330-000 Clevis Pin 1 E 0026-349-000 Clevis Pin 1 F 0026-341-000 Clevis Pin 2 G 0027-020-000 Rue Ring Cotter 5 H 0027-025-000 Rue Ring Cotter 2 J 0081-400-000 Needle Bearing 1 L 1040-006-141 Cam Pivot 1 M 1040-006-144 Drive Link 1 N 1040-006-146 Torsion Spring 1 P 0081-305-000 Track Roller 1 R 1040-006-209 Dampener 1 T 1040-006-313 Lift Cam 1 U 1040-106-185 Dampener Arm Weldment 1 V 1115-006-221 Cam Bracket Weldment 1 W 0081-294-000 Flange Bearing 2 Y 1040-025-027 Link Spacer 1 AA 0081-345-000 Flange Bearing 1
Return To Table of Contents
64 1037-0 09-002 REV A www.stryker.com
Page 65

Big Wheel Carriage Assembly

1040-215-201 Rev A (Reference Only)
Item Part No. Part Name Qty.
A 0014-004-000 Washer 1 B 0026-341-000 Clevis Pin 1 C 0027-020-000 Rue Ring Cotter 1 D 0028-330-000 Spiral Retaining Ring 3 E 0081-011-000 Needle Bearing 1 F 1040-015-038 Washer 1 G 1040-015-053 Carriage Spring Retainer 1 H 1040-015-078 Label, Big Wheel 2 J 1040-015-106 Carriage Return Spring 1 K 1040-020-122 Cam Follower Pivot Pin 1 L 1040-020-128 Lift Cam Roller 1 M 1040-020-129 Carriage Guide Roller 1 N 1040-215-110 Dual Sided Control Carriage Weldment 1 P 1115-015-070 Big Wheel Assembly 2 R 1115-015-073 Big Wheel Cap 2
Return To Table of Contents
www.stryker.com 1037- 009-002 REV A 65
Page 66

Big Wheel Dual Sided Hydraulics Assembly

1115-005-500 Rev B (Reference Only)
Return To Table of Contents
66 1037- 009 -002 RE V A www.stryker.com
Page 67
Big Wheel Dual Sided Hydraulics Assembly
Return To Table of Contents
www.stryker.com 1037- 009-002 REV A 67
Page 68
Big Wheel Dual Sided Hydraulics Assembly
Big Wheel Dual Sided Hydraulics Assembly - 1115-005-500 Rev B (Reference Only)
Item Part No. Part Name Qty.
A 0011-023-000 Washer 2 B 0014-071-000 Washer 2 C 0023-288-000 Hex Washer Head Screw 7 D 0027-031-000 Hair Pin Cotter 1 E 0038-497-000 Extension Wire 3 F 0753-004-014 Release Rod, Head End 1 G 0753-004-132 Release Pedal Swivel 2 H 0753-005-044 Pump Pedal Bushing 2 J 0753-005-074 Pivot Pin 1 K 0753-005-088 Wear Strip 2 L 0753-005-089 Pump Ram Plug 2 M 1040-004-015 Release Rod, Foot End 1 N 1040-010-215 Release Rod Bracket 1 P 1115-004-201 Lowering Pedal Assembly (page 70) 1 R 1115-005-037 Pump Connecting Rod Weldment 1 T 1115-005-075 Pump Pedal Link 1 U 1115-005-285 Pump Pedal Assy, Head End (page 69) 1
Return To Table of Contents
68 1037- 009 -002 REV A www.stryker.com
Page 69

Pump Pedal Assembly, Head End - 1115-005-285

Rev A
Item Part No. Part Name Qty.
A 0026-343-000 Groove Pin 2 B 0715-001-140 Vinyl Tube 1 C 0753-005-044 Pump Pedal Bushing 2 D 1105-201-126 Pump Pedal Plastic 2 E 1115-005-180 Pump Pedal Weldment, Head End 1
Return To Table of Contents
www.stryker.com 1037- 009-002 REV A 69
Page 70

Lowering Pedal Assembly - 1115-004-201

Rev A
Item Part No. Part Name Qty.
A 0025-079-000 Dome Head Rivet 4 B 0753-004-029 Release Pedal Standoff 4 C 0853-004-320 Release Pedal Support 2 D 1105-201-127 Short Uni-Pedal 2 E 1115-004-004 Release Pedal Weldment 2
Return To Table of Contents
70 1037-009- 002 REV A w ww.stryker.com
Page 71

Big Wheel Four-Sided Control Base Assembly

1115-025-205 Rev B (Reference Only)
Torque item A to 18 ± 3 ft-lb
Torque item A
to 18 ± 3 ft-lb
Return To Table of Contents
www.stryker.com 1037- 009-002 REV A 71
Page 72
Big Wheel Four-Sided Control Base Assembly
Return To Table of Contents
72 1037-009- 002 REV A w ww.stryker.com
Page 73
Big Wheel Four-Sided Control Base Assembly
Big Wheel Four-Sided Control Base Assembly - 1115-025-205 Rev B (Reference Only)
Item Part No. Part Name Qty.
A 0003-381-000 Hex Washer Head Truss Screw 2 B 0021-166-000 Set Screw 1 C 0026-067-000 Slotted Spring Pin 2 D 0026-251-000 Clevis Pin 7 E 0026-295-000 Clevis Pin 1 F 0026-393-000 Clevis Pin 2 G 0027-020-000 Rue Ring Cotter 10 K 0042-020-000 Collar 1 L 0853-003-064 Brake Rod Crank Cap 2 M 0853-203-011 Brake Activation Crank 2 N 1040-203-113 Brake Rod 1 P 1040-003-013 Timing Cam Hard Stop 1 R 1040-003-015 Big Wheel Timing Cam Crank Assembly 1 T 1040-025-026 Brake Rod Bushing 1 U 1040-115-007 Carriage Pivot Bushing 2 V 1040-225-201 Side Control Carriage Assembly (page 74) 1 W 1105-001-335 Label, Brake (Red) 2 Y 1105-001-336 Label, Steer (Green) 2 AA 1105-005-154 Butterfly “V” Pedal 2 AB 1115-003-405 Standard Brake Assembly (page 60) 1 AC 1115-005-500 Big Wheel Dual Sided Hydraulics (page 66) 1
Return To Table of Contents
www.stryker.com 1037- 009-002 REV A 73
Page 74

Big Wheel Side Control Carriage Assembly

1040-225-201 Rev B (Reference Only)
Return To Table of Contents
74 1037- 009-002 REV A www.stryker.com
Page 75
Big Wheel Side Control Carriage Assembly
Big Wheel Side Control Carriage Assembly - 1040-225-201 Rev B (Reference Only)
Item Part No. Part Name Qty.
A 0011-148-000 Washer 2 B 0011-525-000 Washer 4 C 0014-004-000 Washer 1 D 0026-341-000 Clevis Pin 1 E 0026-342-000 Grooved Pin 3 F 0027-020-000 Rue Ring Cotter 1 G 0028-166-000 External Retaining Ring 1 H 0028-330-000 Spiral Retaining Ring 1 J 0081-011-000 Needle Bearing 4 K 0081-175-000 Washer 2 L 0753-003-219 Side Control Brake Rod 1 M 1040-015-038 Washer 1 N 1040-015-053 Carriage Spring Retainer 1 P 1040-015-078 Label, Big Wheel 2 R 1040-015-106 Carriage Return Spring 1 T 1040-020-122 Cam Follower Pivot Pin 1 U 1040-020-128 Lift Cam Roller 1 V 1040-020-129 Carriage Guide Roller 1 W 1040-125-010 Side Control Linkage Assy (page 76) 1 Y 1040-025-014 Side Control Wheel Spacer 2 AA 1040-025-017 Side Control Pedal Spacer 2 AB 1040-225-110 Four-Sided Control Carriage Weldment 1 AC 1115-005-155 Butterfly “V” Pedal 2 AD 1115-015-070 Big Wheel Assembly 2 AE 1115-015-074 Big Wheel Side Control Cap 2 AF 1105-001-335 Label, Brake (Red) 2 AG 1105-001-336 Label, Steer (Green) 2
www.stryker.com 1037- 009-002 REV A 75
Return To Table of Contents
Page 76

Big Wheel Side Control Linkage Assembly - 1040-125-010

Rev B
Item Part No. Part Name Qty.
A 0753-003-098* Flat Head Semi-Tubular Rivet 4 B 0753-003-117* Rod End Link 1 C 1040-025-011* Main Link 1 D 1040-025-013* Toggle Pivot Plate 2 E 1040-025-016* Main Link Cover 2 F 1040-025-020* Yoke Weldment 2 G 1040-125-018* Toggle Pivot Spacer 1 H 1040-025-027* Link Spacer 2
* Shown for reference only. Individual part components are not available for sale.
Return To Table of Contents
76 10 37- 009-002 REV A www.stryker.com
Page 77

Base Labeling Assembly, Standard Brakes

0747-010-100 Rev A (Reference Only)
Item Part No. Part Name Qty.
A 0747-001-035 Standard Hood 1 B 0747-010-134 Dipped Bellows 2 C 0946-201-060 Label, Stryker Logo 4 D 0753-010-351 Label, Brake/Steer, Foot End 1 E 0853-010-355 Label, Lift/Lower, Left 1 F 0753-010-370 Label, Brake/Steer, Head End 1 G 0853-010-354 Label, Lift/Lower, Right 1
Return To Table of Contents
www.stryker.com 1037- 009-002 REV A 77
Page 78

Base Labeling Assembly, Four-Sided Brakes

0747-010-200 Rev A (Reference Only)
Item Part No. Part Name Qty.
A 0747-010-034 Hood, Four-Sided Brakes 1 B 0747-010-134 Dipped Bellows 2 C 0946-201-060 Label, Stryker Logo 4 D 0853-010-018 Label, Brake/Steer, Right 1 E 0853-010-019 Label, Brake/Steer, Left 1 F 0753-010-351 Label, Brake/Steer, Foot End 1 G 0853-010-355 Label, Lift/Lower, Left 1 H 0753-010-370 Label, Brake/Steer, Head End 1
Return To Table of Contents
78 1037-009- 002 REV A www.stryker.com
J 0853-010-354 Label, Lift/Lower, Right 1
Page 79

Base Labeling Assembly - Big Wheel Base

1037-010-100 Rev A (Reference Only)
Item Part No. Part Name Qty.
A 0747-010-134 Dipped Bellows 2 B 1037-001-035 Big Wheel Hood 1 C 0946-201-060 Label, Stryker Logo 4 D 0753-010-351 Label, Brake/Steer, Foot End 1 E 0853-010-355 Label, Lift/Lower, Left 1 F 0753-010-370 Label, Brake/Steer, Head End 1 G 0853-010-354 Label, Lift/Lower, Right 1
Return To Table of Contents
www.stryker.com 1037- 009-002 REV A 79
Page 80
1037-030-010 Rev A (Reference Only)

Litter Assembly

Return To Table of Contents
80 1037- 009 -002 RE V A www.stryker.com
Page 81
Litter Assembly
Torque item T
to 23 ± 3 ft-lb
Torque item T to 23 ± 3 ft-lb
Return To Table of Contents
www.stryker.com 1037- 009-002 REV A 81
Page 82
Litter Assembly
Return To Table of Contents
82 1037-0 09-002 REV A www.stryker.com
Page 83
Litter Assembly
Litter Assembly - 1037-030-010 Rev A (Reference Only)
Item Part No. Part Name Qty.
A 0003-035-000 Hex Head Cap Screw 2 B 0003-047-000 Hex Head Cap Screw 28 C 0003-050-000 Hex Head Cap Screw 2 D 0003-054-000 Hex Head Cap Screw 4 E 0003-074-000 Hex Head Cap Screw 2 F 0003-078-000 Hex Head Cap Screw 8 G 0004-021-000 Socket Head Cap Screw 4 H 0004-515-000 Button Head Cap Screw 14 J 0004-161-000 Button Head Cap Screw 4 K 0008-024-000 Socket Head Set Screw 4 M 0014-003-000 Washer 4 N 0014-021-000 Washer 4 P 0016-028-000 Hex Nut 44 R 0016-035-000 Nylock Hex Nut 2 S 0021-104-000 Set Screw 2 T 0023-288-000 Hex Washer Head Screw 2 W 0025-038-000 Rivet 20 Y 0025-099-000 Rivet 32 Z 0028-023-000 External Retaining Ring 2 AA 0037-049-000 Rectangular Hole Plug 8 AB 0037-059-000 Heyco Hole Plug 1 AC 0037-063-000 Hole Plug 2 AG 0721-026-066 Pivot Screw 14 AH 0721-026-069 Upright Sleeve 10 AJ 0721-026-074 Plated Lock Handle 2 AK 0721-032-049 Bumper Roller 4 AM 0721-040-026 Footboard Receptacle 2 AT 1010-001-017 Roller Plate 4 AW 1010-026-017 Siderail Assembly, Right (page 88) 1 AX 1010-026-019 Siderail Assembly, Left (page 87) 1 AY 1010-026-069 Lock Support 2 AZ 0742-026-086 Lock Housing, Right 1 BA 0742-026-087 Lock Housing, Left 1 BC 1010-032-092 Foley Bag Rack 1 BD 1037-001-040 Footboard Support Assembly 1 BE 1037-001-042 Roller Support Assembly, Left 2 BF 1037-001-043 Roller Support Assembly, Right 2 BG 1020-001-053 Label, Euro Centering 1 BH 1020-001-059 Trend Roller Bar 2 BJ 1037-001-061 Litter Frame Assembly 1 BK 1037-022-023 Guide Tube Assembly 2 BM 1037-022-026 Adjustment Bracket 2 BN 1020-022-028 Squeeze Label 1 BP 1037-024-002 Litter Support Assembly, Foot End (page 86) 1
Return To Table of Contents
www.stryker.com 1037- 009-002 REV A 83
Page 84
Litter Assembly
Litter Assembly - 1037-030-010 Rev A (Reference Only) (Continued)
BR 1037-024-003 Litter Support Assembly, Head End (page 85) 1 BS 1020-026-021 Bumper Channel 2 BZ 1020-032-019 Pivot Bolt 2 CA 1037-032-025 Footsection Weldment 1 CB 1037-032-031 Litter Riser, Right 1 CC 1037-032-032 Litter Riser, Left 1 CD 1020-091-052 Centering Euro-Label 2 CE 1020-032-026 Foot Section Skin 1 CF 1210-800-008 Patent Label 1 CG 0038-220-000 Compression Spring 2 CH 0001-096-000 Flat Countersunk Head Machine Screw 4 CJ 1010-001-013 Foot End Cover, Right 1 CK 1010-001-014 Foot End Cover, Left 1 CL 0747-026-103 Retainer Spring 2
Return To Table of Contents
84 1037-0 09-002 REV A www.stryker.com
Page 85

Litter Support Assembly, Head End - 1037-024-003

Rev A
Item Part No. Part Name Qty.
A 0938-001-401 Collar 2 B 1020-024-004 Jack Support Weldment, Left 1 C 1020-024-005 Jack Support Weldment, Right 1 D 1037-010-030 Support Tube 1
Return To Table of Contents
www.stryker.com 1037- 009-002 REV A 85
Page 86

Litter Support Assembly, Foot End - 1037-024-002

Rev A
Item Part No. Part Name Qty.
A 0003-040-000 Hex Head Cap Screw 2 B 0016-036-000 Nylock Hex Nut 2 C 0017-003-000 Cap Nut 4 D 0025-053-000 Rivet 4 E 1037-010-029 Support Tube 1 F 0938-001-292 Support Tube Roller 4 G 0938-001-401 Collar 2 H 1010-032-064 Carrier Tube 2 J 1037-001-048 Support Tube Assembly, Foot End 2 K 0081-063-000 Bearing 4
Return To Table of Contents
86 1037- 009-002 RE V A www.stryker.com
Page 87

Siderail, Left - 1010-026-017

Rev D
Item Part No. Part Name Qty.
A 1010-026-015 Top Rail 1 B 1010-026-083 Upright 4 C 1010-026-084 Upright, Bent 1 D 1010-026-082 Sleeve Bearing 6 E 0025-106-000 Semi-Tubular Rivet 6 F 1010-026-010 Round Hole Plug 4 H 1010-026-085 Latch Upright 1 J 1010-026-012 Bent Spindle Rest 1
Return To Table of Contents
www.stryker.com 1037- 009-002 REV A 87
Page 88

Siderail, Right - 1010-026-019

Rev D
Item Part No. Part Name Qty.
A 1010-026-015 Top Rail 1 B 1010-026-083 Upright 4 C 1010-026-084 Upright, Bent 1 D 1010-026-082 Sleeve Bearing 6 E 0025-106-000 Semi-Tubular Rivet 6 F 1010-026-010 Round Hole Plug 4 H 1010-026-085 Latch Upright 1 J 1010-026-012 Bent Spindle Rest 1
Return To Table of Contents
88 1037- 009 -002 RE V A www.stryker.com
Page 89

Pneumatic Fowler to Litter Assembly

1037-031-011 Rev A (Reference Only)
Item Part No. Part Name Qty.
A 1010-031-078 Gas Cylinder 2 B 1037-031-025 Cylinder Mount 2 C 0016-035-000 Nylon Hex Nut 2 D 0014-021-000 Flat Washer 4 E 0003-047-000 Hex Head Cap Screw 10 F 0016-028-000 Nylon Hex Nut 10 G 1020-031-038 Fowler Rest Bumper 2 H 1037-031-017 Fowler Rest, Right 1 J 1037-031-019 Fowler Rest, Left 1
Return To Table of Contents
www.stryker.com 1037- 009-002 REV A 89
Page 90

Pneumatic Fowler Assembly

1037-031-010 Rev A (Reference Only)
Item Part No. Part Name Qty.
A 0037-065-000 Heyco Hole Plug 2 B 1020-031-020 Handle Assembly 1 C 1037-031-015 Fowler Weldment 1 D 1020-031-039 Fowler Skin 1 E 1510-031-028 Yoke 2 F 1510-031-037 Pivot 2 H 0015-050-000 Hex Hut 2 J 0021-126-000 Set Screw 2 K 0946-035-025 Liner 4 L 0028-076-000 External Retaining Ring 4 M 0025-099-000 Pop Rivet 17 N 0028-008-000 External Retaining Ring 4 O 0015-037-000 Hex Jam Nut 2 P 0021-104-000 Set Screw 2 R 0021-119-000 Set Screw 2 S 1010-032-066 Rectangle Hole Plug 2 T 0004-149-000 Button Head Cap Screw 4 W 0016-003-000 Nylock Hex Nut 4 Y 0025-069-000 Pop Rivet 4 Z 1020-023-012 Tray Handle, Left Hand 1 AA 1020-023-013 Tray Latch 1 AB 1020-023-014 Tray Latch 2
Return To Table of Contents
90 1037- 009-002 REV A www.stryker.com
Page 91

Transfer Board Assembly

1037-024-020 Rev A (Reference Only)
Item Part No. Part Name Qty.
A 0002-100-000 Pan Head Machine Screw 4 B 0025-079-000 Pop Rivet 4 C 0014-021-000 Washer 4 D 0016-003-000 Fiberlock Hex Nut 4 E 0028-093-000 Retaining Ring 8 F 0038-252-000 Extension Spring 2 G 1010-024-030 Board Support Assembly (page 94) 2 H 1020-001-029 Bearing 4 J 1037-024-010 Transfer Board System, Left (page 92) 1 K 1037-024-011 Transfer Board System, Right (page 93) 1 L 1020-024-121 Board Retainer 2 M 0004-032-000 Socket Head Cap Screw 2 N 0004-142-000 Socket Head Cap Screw 2 P 0011-179-000 Nylon Washer 2 R 0016-028-000 Nylock Nut 2 S 1020-024-034 Support Plate, Left 1 T 1020-024-035 Support Plate, right 1
Return To Table of Contents
www.stryker.com 1037- 009-002 REV A 91
Page 92

Transfer Board Assembly, Left - 1037-024-010

Rev A
Item Part No. Part Name Qty.
A 1037-032-100 Transfer Board Assembly 1 B 0721-024-046 Label 1 C 1037-024-038 Connecting Link Assembly 1 D 1020-024-012 Pivot Arm Assembly, Left 2 E 0001-025-000 Flat Head Machine Screw 2 F 0011-224-000 Nylon Flat Washer 4 H 0016-028-000 Nylock Hex Nut 2 K 0025-157-000 Rivet 2 L 1211-132-025 Pivot Sleeve 2
Return To Table of Contents
92 1037-0 09-002 REV A www.stryker.com
Page 93

Transfer Board Assembly, Right - 1037-024-011

Rev A
Item Part No. Part Name Qty.
A 1037-032-100 Transfer Board Assembly 1 B 0721-024-046 Label 1 C 1037-024-037 Connecting Link Assembly 1 D 1020-024-013 Pivot Arm Assembly 1 E 0001-025-000 Flat Head Machine Screw 2 F 0011-224-000 Nylon Flat Washer 4 H 0025-157-000 Rivet 2 K 0016-028-000 Nylock Hex Nut 2 L 1020-024-033 Pivot Arm Assembly, Right 1 M 1211-132-025 Pivot Sleeve 2
Return To Table of Contents
www.stryker.com 1037- 009-002 REV A 93
Page 94

Arm Board Support Assembly - 1010-024-030

Rev C
Item Part No. Part Name Qty.
A 1010-024-015 Support Block 1 B 1010-024-016 Support Arm 1 C 1010-024-014 Label, Warning 1 D 0038-263-000 Compression Spring 1 E 0008-017-000 Shoulder Bolt 1 F 1010-026-046 Ball Knob 1
Return To Table of Contents
94 1037-0 09-002 REV A ww w.stryker.com
Page 95

X-Ray Tray Assembly, Right Side Load - 1037-022-000

1037-022-010 Rev A (Reference Only)
Return To Table of Contents
www.stryker.com 1037- 009-002 REV A 95
Page 96
X-Ray Tray Assembly, Right Side Load - 1037-022-000
Item Part No. Part Name Qty.
A 0004-026-000 Socket Head Cap Screw 3 B 0004-171-000 Button Head Cap Screw 3 C 0004-175-000 Button Head Cap Screw 4 D 0004-265-000 Button Head Cap Screw 8 E 0011-146-000 Washer 1 F 0014-004-000 Washer 6 G 0016-003-000 Nylock Hex Nut 5 H 0016-014-000 Nylock Hex Nut 4 J 0025-079-000 Rivet 6 K 0028-098-000 E-Ring 6 L 0037-064-000 Bumper, Grommet 4 M 0045-952-000 O-Ring 12 N 1010-022-035 Retention Spacer, Right 1 P 1010-022-036 Retention Spacer, Left 1 R 1010-032-066 Hole Plug 2 T 1020-022-007 Brake Handle 1 U 1037-021-014 Tray Pan 1 V 1020-022-015 Pivot Tube Assembly 1 W 1020-022-036 Brake Adjustment Bracket 1 Y 1037-022-044 Frame Assembly 1 AA 1020-022-025 Wheel Axle 6 AB 1020-022-059 Wheel 6 AC 1020-022-060 Label, Yellow 1 AD 1020-022-061 X-Ray Tray Spacer 4 AE 1020-022-062 Drawer Slides 1 AF 0038-253-000 Extension Spring 1 AG 0004-032-000 Socket Head Cap Screw 2 AH 1020-021-012 Tray Indicator Weldment, Right 1
Return To Table of Contents
96 1037- 009 -002 REV A www.stryker.com
Page 97

X-Ray Tray Assembly, Left Side Load - 1037-021-000

1037-021-010 Rev A (Reference Only)
Return To Table of Contents
www.stryker.com 1037- 009-002 REV A 97
Page 98
X-Ray Tray Assembly, Left Side Load - 1037-021-000
Item Part No. Part Name Qty.
A 0004-026-000 Socket Head Cap Screw 3 B 0004-171-000 Button Head Cap Screw 3 C 0004-175-000 Button Head Cap Screw 4 D 0004-265-000 Button Head Cap Screw 8 E 0011-146-000 Washer 1 F 0014-004-000 Washer 6 G 0016-003-000 Nylock Hex Nut 5 H 0016-014-000 Nylock Hex Nut 4 J 0025-079-000 Rivet 6 K 0028-098-000 E-Ring 6 L 0037-064-000 Bumper, Grommet 4 M 0045-952-000 O-Ring 12 N 1010-022-035 Retention Spacer, Right 1 P 1010-022-036 Retention Spacer, Left 1 R 1010-032-066 Hole Plug 2 T 1020-021-007 Brake Handle 1 U 1037-021-014 Tray Pan 1 V 1020-021-015 Pivot Tube Assembly 1 W 1020-021-036 Brake Adjustment Bracket 1 Y 1037-021-044 Frame Assembly 1 AA 1020-022-025 Wheel Axle 6 AB 1020-022-059 Wheel 6 AC 1020-022-060 Label, Yellow 1 AD 1020-022-061 X-Ray Tray Spacer 4 AE 1020-022-062 Drawer Slides 1 AF 0038-253-000 Extension Spring 1 AG 0004-032-000 Socket Head Cap Screw 2 AH 1020-021-017 Tray Indicator Weldment, Right 1
Return To Table of Contents
98 1037- 009 -002 RE V A www.stryker.com
Page 99

X-Ray Grid Holder Assembly - 1020-027-000

1020-027-010 Rev A (Reference Only)
Item Part No. Part Name Qty.
A 1020-027-021 Guide Weldment, Right 1 B 1020-027-022 Guide Weldment, Left 1 C 1020-027-011 Slider Weldment 2 D 0011-271-000 Fender Washer 4 E 0004-131-000 Button Head Cap Screw 10 F 1020-027-024 L Bracket 2
Return To Table of Contents
www.stryker.com 1037- 009-002 REV A 99
Page 100

Optional X-Ray Centering Guide - 1020-020-000

Rev C
Item Part No. Part Name Qty.
A 0001-026-000 Flat Head Countersunk Machine Screw 2 B 0001-085-000 Countersunk Flat Head 4 C 0004-127-000 Socket Head Cap Screw 4 D 0004-169-000 Button Head Cap Screw 1 E 0004-170-000 Button Head Cap Screw 1 H 0011-132-000 Flat Washer 1 J 0024-051-000 Medium Utility Clamping Knobs 1 K 0037-064-000 Grommet Bumpers 8 L 0052-250-000 Special Nylon Spacers 2 M 1020-022-021 Slide Block 4 N 1020-022-041 Spur Gear Modified 1 O 1020-022-043 Rack Gear Modified 2 P 1020-022-052 Guide Plate Assembly 1 R 1020-022-055 Slide Pad 2 S 1020-022-056 Centering Plate 2 T 1020-022-057 Rack Connector, Left 1 W 1020-022-058 Rack Connector Assembly 1
Return To Table of Contents
100 1037- 009 -002 REV A www.stryker.com
Loading...
Buy Points How it Works FAQ Contact Us Questions and Suggestions Privacy Policy Cookie Policy Terms of Use