Structural Concepts Impulse CSC3223 Installation & Operating Manual

READ AND SAVE THESE INSTRUCTIONS

INSTALLATION &

OPERATING MANUAL

SELF-SERVICE COUNTERTOP UNIT - MODEL CSC3223

I:\Oper Manuals\Impulse\CSC3223_99425.pub

SCC P/N

99425

888 E. Porter Road · Muskegon, MI 49441 Phone: [phone] Fax: [phone] www.structuralconcepts.com

Rev F Date: 6.19.2012

TABLE OF CONTENTS

OVERVIEW AND WARNINGS ……………….……………..…………………..…….………….....…..………

INSTALLATION ………….…………………………………………………………………………………
START-UP AND OPERATION ……….. …..….…………………...………...…..………………………

MAINTENANCE FUNDAMENTALS: SHELF ASSEMBLY REMOVAL / DECKING REMOVAL ... .

MAINTENANCE FUNDAMENTALS: STD. DOOR MECHANISM / RYOBI DOOR ME CHANISM ..
LIGHT FIXTURES - FLUORESCENT …………………………………………………………………..
LIGHT FIXTURES - LED ………………………………………………………………………………….
SERIAL LABEL LOCATION & INFORMATION LISTED / TECH INFO & SERVICE………………..
TROUBLESHOOTING ……………….……………………………………………….………….… … …..
ILLUSTRATED PARTS BREAKDOWN …………………………………………………….…...………
PARTS LIST ……………..…………………………………………………………………………………
CLEANING SCHEDULE..…………………………………………………...…………… …….…… ……

TECHNICAL SERVICE CONTACT INFORMATION & WARRANTY INFORMATION ….....………

3
4
5
6
7
8

9
10
12
13
14
15
16

2

OVERVIEW AND WARNINGS

OVERVIEW

 The Structural Concepts non-refrigerated service cases are designed to merchandise unpackaged bakery

products at ambient temperatures.

 These cases should be installed and operated according to the following instructions to insure proper

performance.

 This unit is designed for the display of products in ambient store conditions where temperatures and

humidity are maintained at a maximum of 75° F and 55% relative humidity.

CAUTION

WARNING

ELECTRICAL

HAZARD

CAUTION! LAMP REPLACEMENT GUIDELINES

LED lamps reflect specific size, shape and overall design.

Any replacements must meet factory specifications.

Fluorescent lamps have been treated to resist breakage and

must be replaced with similarly treated lamps.

WARNING

Risk of electric shock.

Disconnect ALL ELECTRICAL SOURCES before servicing.

CAUTION! GFCI BREAKER USE RECOMMENDATION

If N.E.C. (National Electric Code) or your local code

requires GFCI (Ground Fault Circuit Interrupter) protection,

the use of a GFCI breaker

is strongly recommended.

 Each case has its own wiring diagram folded & in its own packet.
 Wiring diagram placement may vary; it may be placed near ballast

box, field wiring box, raceway cover, or other related location.

CAUTION! POWER CORD AND PLUG MAINTENANCE

Risk of electric shock. If cord or plug becomes damaged,

replace only with cord and plug of same type.

WIRING DIAGRAM FORMAT & LOCATION

3

INSTALLATION

Remove Unit From Skid

 Position the unit near a suitable electrical outlet.
 Caution: Case must always remain supported or center of gravity will allow case to fall.
 Slide unit to rear of skid and tip backward off skid.

Position and Level Units

For your safety, equipment is furnished with a properly grounded cord connector. Do not attempt to
defeat the grounded connector.

Lift unit with suitable prying bar and blocking. Use care to lift in manner to minimize damage to case.
Rotate leveler to obtain proper height to stabilize and level the unit.

Carefully Slide Unit
Out From Skid

4

START-UP AND OPERATION

For your safety, equipment is furnished with a properly
grounded cord connector. Do not attempt to defeat
the grounded connector.

Set-up Counter Top Unit

 Remove case from skid and place on counter in the

position at which the case will reside.

 Note: The following steps must be completed before

this display case may be put in service.

 1. After case is in position, apply a steady bead of

silicone around the base and counter top.

 2. Allow 24 hours for the silicone to dry before using

the case.

 Electrical 120V stub up connections are provided in

the light switch box.

Merchandiser Start-Up

 Do not use an extension cord with this appliance.
 Do not operate this equipment with a damaged cord,

plug or outlet.

 Insure the power switch is off.
 Plug cord into a certified 120V electrical outlet with

ground.

Fluorescent Lights Only

 Turn lights on.

 On the counter top unit, the light switch is located

behind the tissue box.

 On floor models without a storage door the switch

is located at the front base of the unit under the
front panel on the left hand side.

 On floor models with a storage door, the light

switch is located inside the base storage area
on the left hand side.

 Lights should come on at the same time. First time

lighting may require short warm-up period for bulbs.
Slightly dim or a flickering of new bulbs is normal.

LED Lights Only

 Lights will come on when case is plugged in.

Tissue Dispenser

 Remove tissue dispenser.
 Place a tissue box into the dispenser as shown.

Adjustable Front Storage Area Dividers (Optional)

 Dividers are held in place with magnetic tape strips.
 Dividers may be adjusted to reflect varying widths.
 Dividers may be entirely removed from case.

Light Switch

—— Tissue Dispensers ——

Adjustable Front Storage Dividers

(Retained With Magnetic Tape)

5