21
There are a number of wiring options dependant on the
location and personal preference:
Option 1 – Connection to License Plate Light Wiring
A. Using a test light, determine the polarity of the two wires
that run to the License Plate light.
B. Connect the BLACK STRIPED (+) wire from the Scrolling
LED Panel to the 12V (+) wire running to the vehicle
license plate frame.
C. Connect the [COLOR} wire from the Scrolling LED Panel to
a chassis ground.
Option 2 – Connection to a Fused Switch
A. Install a fused switch (sold separately) from [WHAT] to
bring power to the Scrolling LED Panel
B. Connect the BLACK STRIPED (+) wire from the Scrolling
LED Panel to the 12V (+) wire in the fused switch.
C. Connect the [COLOR} wire from the Scrolling LED Panel to
a chassis ground.
Option 3 – Connection Brake Light Wiring
A. Using a test light, determine the polarity of the wires that
run to the vehicle’s brake lights. This step requires two
people.
B. While stepping on the brake pedal, test each wire in the
wire harness to determine which is the 12V (+) wire.
Connect the BLACK STRIPED (+) wire from the Scrolling
LED Panel to the 12V (+) wire.
C. Connect the [COLOR] wire from the Scrolling LED Panel to
a chassis ground.
3. Basic Operation:
3.1
Turning the scrolling LED panel on and o.
When you plug in the scrolling LED panel's power, the
scrolling LED panel starts up automatically. Unplugging the
power turns the scrolling LED panel o.
In additional, you can use the supplied remote control to
turn the scrolling LED panel o.
1. Installation instructions:
1.1
All mounting surface must be clean and free of all dirt, wax,
and oil prior to the installation. Wipe all areas with the
alcohol prep pad provided and let dry thoroughly.
1.2
Select a location to mount the Scrolling LED Panel. There are
a number of mounting options:
Option 1 – License Plate Bracket Mounting
A. Remove the two machine bolts that hold the license
plate in place.
B. Place the Scrolling LED Panel above the license plate
and reattach using the Locking Bolts provided.
Locking Bolts prevent theft of the unit.
C. Tighten locking bolts using the Locking Key provided.
Do not over tighten.
D. Install two rubber plugs provided over the top of the
Locking Bolts. Store the Locking Key in a secure location.
Option 2 – Interior Glass Mounting
A. Attach two (2) suction cups to the Scrolling LED Panel
using screws. Suction cups and screws are provided.
B. Mount the Scrolling LED Panel to the interior surface
of the glass.
Option 3 – Alternate Interior Mounting
A. The Scrolling LED Panel may be mounted to most any
interior surface including dashboards, door panels,
center consoles, etc. using double faced tape
(provided)kit.
2. Connecting power to the Scrolling LED
panel:
Caution: Connecting power to this product requires knowledge of 12V automotive wiring applications. Incorrect
installation or wiring will likely damage or destroy this
product. If unsure regarding the process, refer to an
automotive shop experienced in the installation of such
products.
3
3.2 Introduction To The Remote Control
4
4. Creating a Text message:
4.1 Edit mode/creating or editing message
Step 1:
Press the EDIT button. This puts the scrolling LED panel into
edit mode. The screen will display:
Note : the number after "P" indicates the memory location
(in this case, location 1).
There are 5 memory locations (P:1...P:5) in the scrolling LED
panel. Each memory location can hold a separate message
that you can select later. If the selected location already
contains a message, you will need to scroll to an empty
location to input a new message or the current message will
be edited. To change the memory location, press either PREV
button or NEXT button until the screen shows the desired
memory location. Press ENTER to make your conrmation.
Step 2:
After you have selected a memory location for your
message, your scrolling LED panel will display the scrolling
speed for the message you are going to input:
Note : SP indicates the speed at which your message will
scroll.
SP1 : fast
SP2 : moderate
SP3 : slow
There are 3 preset scrolling speeds (SP:1...SP:3) in the
scrolling LED panel. To change the speed, press either PREV
button or NEXT button until the screen shows the desired
scrolling speed. Press ENTER to make your conrmation.
Step 3:
After selecting the scrolling speed, your scrolling LED panel
will go into edit mode, indicated as follow:
The blinking rectangle indicates that you are ready to input
text and/or characters (the blinking rectangle also
represents a blank space when inputted)
Press the SHIFT button to toggle among the dierent
character sets (lower case letters, capital letters, numbers,
and symbols). See appendix B for a complete listing of the
available characters. The character sets will be indicated as
follows:
Capital letters : Blinking "A"
Lower case letters : Blinking "a"
Numbers : Blinking "0"
Symbols : Blinking "!"
Blank Space : Blanking "n" (The blank space is accessible by
pressing PREV button while display the capital "A")
Once you have selected the desired character set, use the
PREV/NEXT buttons to scroll through the available characters in that set until you reach the desired character. The
PREV/NEXT buttons will scroll through the alphabet (in the
capital and lower case modes), numbers 0 through 9 (in
number mode), or through a variety of symbols (in symbol
mode).
In addition, pressing the PREV/NEXT buttons at the end or
beginning of a character set will advance to the next character set. Remember that you can use the SHIFT button at any
time to toggle among the character sets.
Once the character you want to input is displayed, press the
RIGHT button to advance and input the next character or
letter.
Pressing the LEFT button at anytime will return to the
previous character for editing.
5
This Manual is for The SCROLLING LED PANEL Only
Design and specications are subject to change without notice.
SCROLLING LED PANEL
USER’S MANUAL
6
Step 4:
After you have nished building your message, press ENTER
to conrm and save the message. The entered message is
shown for an instant and begins scrolling at the selected
speed.
4.2 Example : Editing A Simple message
Steps
Key
to
Press
1 EDIT Enter edit mode P:1
2 Default memory P:1NEXT/PREV
4 Default speed SP1NEXT/PREV
3
SP:1Conrm the memory
ENTER
5 Conrm the speedENTER
7
Message
starts to
display
Conrm the messageENTER
6 Smart Planet
Enter the character by pressing
LEFT/RIGHT/NEXT/PREV
“Smart Planet”
Explanation Display
You have just created your rst message! Here are some
important things to keep in mind:
If you made a mistake while entering a letter, you can correct
it by pressing the LEFT button until you reach the character
you want to change and then use the PREV/NEXT buttons to
correct it. After making the correction you can use the right
button to get back to where you were.
After entering your message, press ENTER to save it.
Follow the above procedures to enter additional messages
(in any of the available memory locations)
Just remember that no single message can exceed 120
characters in length.
4.3 Running A Saved message
When connecting the power supply, you will have the
option of choosing any of your saved messages to be
displayed by selecting the PREV/NEXT button at any time.
-
-
Steps
Key
to
Press
1 PREV
Preview the message
in P5 memory location
message in P:5 is shown
1
message in P:2 is shown
Preview the message
in P2 memory location
NEXT
Explanation
OR
Display
4.4 Erasing or editing a Saved Message
To erase shorter message simply select the memory location
of the message you want to delete. After entering the Edit
Mode use the ENTER button to get to the character input
screen and replace the message characters with spaces. For
erasing longer messages use the method below.
In this mode you can also edit the saved message by
entering a letter or symbol instead of the blank space.
Another way to delete a single letter while in the edit mode
is to use the CLR(SLEEP) button. enter edit mode and
highlight the letter you wish to delete using the RIGHT or
LEFT buttons:
Press CLR (SLEEP) button to delete the letter "c"
4.5 Deleting A Saved message
Press the EDIT button. It will display a memory location:
Press the CLR (Sleep) button to clear the message stored in
the selected memory location.
4.6 Sleep mode
The SLEEP button acts as the power button allowing you
turn the scrolling LED panel on or o.
Appendix A : Additional Programming Tips
The following functions require that you move through the
list of possibilities and make a selection. use NEXT / PREV /
LEFT / RIGHT buttons to move through the list of choices
SCROLLING LED PANEL USER’S MANUAL
SCROLLING LED PANEL USER’S MANUALSCROLLING LED PANEL USER’S MANUALSCROLLING LED PANEL USER’S MANUAL
SCROLLING LED PANEL USER’S MANUALSCROLLING LED PANEL USER’S MANUALSCROLLING LED PANEL USER’S MANUAL
7
Function buttons
P
SP
PossibilitiesDenition
memory P:1, P:2, P:3, P:4, P:5
SP:1, SP:2, SP:3
speed
Appendix B : Listing Characters
Trouble Shooting
A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
a b c d e f g h i j k l m n o p q r s t u v w x y z
0 1 2 3 4 5 6 7 8 9 ! @ # $ % & ( )
+ " ' ? , / - < >>: . ; : \ { } ~ [ ] € n
No Display
Not Response
to
remote Control
If the above procedures do not work, please contact
StreetGlow’s warranty Dept.
Ensure that the power wires located at
the back of the scrolling LED panel are
properly connected.
Ensure that the main power coming
from your car's electrical system is
normal.
-
-
The remote control battery may be
dead. Replace the battery with a fresh
one (CR2025)
Make certain that there is no obstruction between the remote control's IR
emitter and the receiving window
on the scrolling LED panel. The receiving window is at the lower left corner
of the scrolling LED panel's display
and can be easily located using a
bright ashlight.
-
-
Caution:
The installation of this produc t requires
knowledge of 12V automotive wiring
applications. Incorrect installation or wiring
will likely damage or destroy this product. If
unsure regarding the process, refer to an
automotive shop experienced in the
installation of such products.
WARNING!
StreetGlow products are recommended for show and o-road use
only. Laws concerning the use of aftermarket lighting products may
vary from state to state. For more information, check with your local
authority.
2 Year Limited Warranty
StreetGlow products are warranted against defects in the material
and /or workmanship according to the following conditions and
limitations:
1. Broken Glass, Labor and transportation are not covered
regardless.
2. Warranty is valid for 2 years from date of purchase.
3. Proof of purchase is required to validate warranty.
4. All warranty claims are to be handled by selling agents.
5. Accident, abuse, neglect, improper installation, not used for
its intended purpose are not covered. This warranty is limited
to replacing the defective part without charge. The company
in no event shall be held responsible for any consequential or
special damages. This warranty gives you specic legal
rights and you may also have rights which vary from state to
state.
INSERT
Inserts a letter
Puts the scrolling LED Panel
into Edit mode
EDIT
Conrms entry
ENTER
Scrolls to the previous
character in the menu
PREV
Moves backward to the previous
character inputted in message
LEFT
Moves forward to the next character
to be inputted in message
RIGHT
Scrolls to the next character
in the menu
NEXT
Toggles among character sets
(lower case, capitals, numbers
symbols)
SHIFT
Deletes a letter or Clears all text
messages in selected memory
location
CLR
Toggles ON/OFF Mode
SLEEP
Note: The Diagram Is For Reference Only. The Actual Appearance May dier From
The Diagram.
CONTENTS:
1 - Scrolling LED panel
1 - Wireless Remote Control
All necessary mounting hardware
and Installation instructions
Loading...