CUHD4K-DUAL
1
2
3
Content
WORKING MODE FLOW CHART ....................................................................... 6
USE YOUR CAMERA ........................................................................................ 8
APPLICATION (SUPPORT ANDROID AND IOS) ..................................................... 17
WATERPROOF CASE ..................................................................................... 22
SECURITY INFORMATION ............................................................................... 23
GENERAL ................................................................................................... 23
SAFETY ...................................................................................................... 24
PRODUCT’S POWER SUPPLY ........................................................................... 24
PLACING OF THE PRODUCT ............................................................................ 25
4
CLEANING .................................................................................................. 25
TROUBLESHOOTING ..................................................................................... 26
IMPORTANT NOTE ........................................................................................ 26
SAFETY-ENVIRONMENT ................................................................................ 27
GUARANTEE CONDITIONS ............................................................................. 28
STOREX WEBSITE ...................................................................................... 31
WARRANTY REGISTRATION ............................................................................ 31
5
6
WORKING MODE FLOW CHART
After turn on the camera, you can press the Power/Mode button to switch the
following modes in turn:
Video Photo Burst photo T ime laps Settings
7
Video
Record Video
Photo
Capture a single photo.
Burst Photo
Capture photo bursts
Time Lapse
Shoot a series of photos at set time intervals
Settings
Adjust camera settings, resolution and more.
8
USE YOUR CAMERA
When you use the camera for the first time, please:
1. Insert a micro SD or micro SDHC card, as shown in the following picture.
High speed card at least Class 4 is recommended; when using time delay
function or recording video in professional mode, the card of Class 10 is required.
Turn off the camera before inserting or removing the card.
9
Charging the battery
The camera uses removable rechargeable lithium battery. When the camera is
off, connect it to the PC via USB cable to charge the battery. During charging, the
status indicator (blue) will light on, and the indicator off when charging
completes.
Note: When the camera is on, connecting it to the PC will not charge.
10
Turn on/off
Turn on: press and hold the button for about 3 seconds, LCD displays “ON”
and a beep can be heard from buzzer.
Turn off: press and hold the button for about 3 seconds, LCD displays “OFF”
and a beep can be heard from buzzer.
Note: The camera will turn off automatically if it is idle for 5 minutes.
11
Start to Use
Video
To record Video, verify the camera is in Video mode. If the Video icon on your
camera’s LCD screen is not showing, press the Power/Mode Button repeatedly
until it appears.
To start recording:
Press the Shutter/Select Button. The camera will emit one beep and the Camera
Status Lights will flash while recording.
12
To stop recording:
Press the Shutter/Select Button. The Camera Status Lights stop flashing and the
camera emits one beep to indicate recording
has stopped.
This camera automatically stops recording when the battery is out of power.
Your Video will be saved before the camera powers OFF.
13
PHOTO MODE
Photo
To capture a Photo, verify the camera is in Photo mode. If the Photo icon on your
camera’s LCD screen is not showing, press the Power/ Mode Button repeatedly
until it appears.
To take a photo:
Press the Shutter/Select Button. The camera
will emit the camera shutter sound.
14
BURST PHOTO MODE
Burst Photo
To capture a Burst Photo series, verify the camera is in Burst Photo mode. If the
Burst Photo icon on your camera’s LCD screen is not showing, press the
Power/Mode Button repeatedly until it appears. In Burst Photo mode, your
camera takes 3 photos in 1.5 seconds.
15
TIME LAPSE
To capture a Time Lapse series, verify the Continuous Lapse is ON and camera is
in T ime Lapse mode. If the Time Lapse icon on your camera’s LCD screen is not
showing, press the Power/Mode Button repeatedly until it appears. In Time
Lapse mode, your camera captures a series of photos at 2, 3, 5, 10, 20, 30 or 60
second intervals.
To take Time Lapse:
Press the Shutter/Select Button. The camera initiates countdown and emits the
camera shutter sound each time a Photo is taken.
16
Enable/disable Wi-Fi
Press and hold the Down/Wi-Fi Button for three seconds to turn OFF Wi-Fi.
17
APPLICATION (SUPPORT ANDROID AND IOS)
1. How to install an APP
1.1 Search for ”Ez iCam” in Google Play or scan the QR code printed on
the gift box to find the APP and install it according to the instruction.
1.2 Search for ”Ez iCam” in APP Store or scan the QR code below.
iOS Android
18
2. Android APP
2.1 Install Ez iCam APP (provided by dealer or via internet) on smartphone or the
product.
2.2 Insert the Micro SD card and turn on the camera, then press the Wi-Fi
button to enable it. Now you can see the Wi-Fi icon on the LCD.
2.3 Enable Wi-Fi on smartphone or the product and search for wireless AP signal
SY5003_WIFI, then connect it to camera, until the system displays “Connected
successfully”.
Note: The first time connecting to CHDW5003, you need to enter password
“1234567890”.
19
2.4 Click the icon in the App list of the Android phone or the product to
open it. Now you can preview the image sent by the camera on the phone or the
product and start some operating.
20
3. iOS APP
3.1 Install Ez iCam APP on iOS phone or the product.
3.2 Insert the Micro SD card and turn on the camera, then press the Wi-Fi
button to enable it. Now you can see the Wi-Fi icon on the LCD.
3.3 Enable Wi-Fi on iOS phone or the product and search for wireless AP signal
SY5003_WIFI, then connect it to camera, until the system displays “Connected
successfully”.
Note: The first time connecting to CHDW5003, you need to enter password
“1234567890”.
21
3.4 Click the icon in the App list of the iOS phone or the product to open it.
Now you can preview the image sent by the camera on the phone or the
product and start some operating. The operation interface on terminal is shown
in the following figure.
22
WATERPROOF CASE
Before sealing the waterproof case, keep the camera housing’s rubber seal
clean, a single hair or grain of sand can cause a leak. You can test by closing
the case without inserting the camera. Submerse the case completely in
water for about a minute. Remove the case from the water, dry off its
exterior with a towel, and then open the case. If the interior is dry, the case
is safe for use under water.
After use in salt water you will need to rinse the outside of the housing
with fresh water and then dry. This will prevent corrosion of the hinge pin
and salt buildup in the seal, which can cause failure.
To clean the seal, rinse in fresh water and shake dry (drying with a cloth
may cause lint to compromise the seal). Re-install the seal into the grooves
in the backdoor of the housing.
23
SECURITY INFORMATION
This device was designed and built in order to guarantee your safety. The safety
mechanisms implemented in the product will protect you if you observe the
following installation, operation and troubleshooting procedures:
Please carefully read and follow the following instructions before handling and
installing your device,
Keep these instructions for further reference.
GENERAL
Don't shake, or it may lead to damage to the product.
Only use components and accessories (power supply...) recommended by the
manufacturer,
The illustrations of the product may vary from actual product.
24
SAFETY
To prevent fire or electric shock, do not put the appliance near objects filled
with liquids;
If a heavy object or liquid is dropped on the device, unplug it immediately and
send it to check by qualified personnel before re-use;
When in operation, the housing surface generates heat; do place the product on
a flat and rigid surface and avoid covering it or placing any object on it.
PRODUCT’S POWER SUPPLY
In case you don’t use the product for a long time or during a lightning storm,
unplug the unit from the outlet by grabbing the plug itself, without pulling the
cable.
The included power adapter is specific to the product. Using a different adapter
may cause damage or accidents.
25
PLACING OF THE PRODUCT
Install the appliance away from any equipment with strong attraction such as
microwave ovens, big speakers...
Place your product in a well-ventilated area and on a hard and flat surface to
disperse heat from the device.
CLEANING
Never open the product to clean, otherwise the warranty will be canceled ;
Unplug the product from the wall outlet before cleaning the product ;
Clean the outside of the product using a soft, dry cloth. Never use an abrasive
pad, scouring powder or solvent such as alcohol or gasoline.
26
TROUBLESHOOTING
Refer all troubleshooting to qualified personnel. Troubleshooting is required
when the appliance has been damaged in any way: plug or cord is damaged,
liquid spilled into the product, introduction of small objects in the product,
exposure to rain or moisture, malfunction, drop of the product...
IMPORTANT NOTE
At full volume, for an extended period of time can damage your hearing.
It is illegal to download music from the Internet without having bought
the rights. STOREX is not responsible for the use of the STOREX product
with illegal music downloading.
27
SAFETY-ENVIRONMENT
Your STOREX product has been laboratory tested; it complies with European
guidelines corresponding to the CE labelling in force at the time of its launch.
Your STOREX product's components are traceable; this demonstrates the
product's compliance to environmental guidelines (RoHS) in force at the time of
its launch.
Once the product has reached the end of its lifespan, don't throw it in a dustbin.
Return it to the retailer or bring it to a rubbish heap, to ensure the product is
properly disposed of via a waste electrical and electronic equipment (DEEE)
channel.
28
GUARANTEE CONDITIONS
STOREX’s available guarantee is valid for 1 year for the product and 3 months for
its accessories (remote control, AV cables, power supply ...).
STOREX guarantees your products against any manufacturing or assembling
faults. This guarantee only applies to the first purchase of the product by the end
user and is not transferable if the device is resold. This warranty does not cover
any incompatibilities found by end user apart from recommendations specified
on the packaging, or any other incompatibility generated by other hardware or
software on the computer that is connected to the product.
Proof of purchase must be presented to our services to apply STOREX guarantee.
29
The guarantee doesn’t cover failures or defects induced by non-compliance to
this manual’s instructions, neglect, alteration, improper installation or
maintenance, reparation or alteration not authorized by STOREX, improper tests,
accident or external factor such as (not exhaustive) excessive heat or dampness,
power failures or bad installation / uninstalling of the product.
The only contractual obligation endorsed by STOREX pertains to the reparation
or replacement of a defective product. In no case, STOREX cannot be held
responsible for any loss of data, or its consequences induced by operational fault
or a product failure.
30
In any case, STOREX won't be bound to any financial responsibility for any
amount exceeding the value of the product purchased by the end user.
This guarantee is well defined and cannot be modified, decreased or increased
without written consent from STOREX. In addition, STOREX cannot be held
responsible for any technical advice or service provided in relation to the
product.
For any request not covered by this guarantee, please contact STOREX support
31
STOREX WEBSITE
Go to http://www.storex.eu.
WARRANTY REGISTRATION
In order to facilitate the management of your issue, should you contact our
support team, we invite you to register your product guarantee on our website
at the following address:
http://garantie.storex.eu
32
For repairing, contact your dealer to repair your product under guarantee, or
send your request via email to the following address:
support@storex.eu
or by phone at:
France: 01 55 85 82 00 (local call charge to Paris)
Spain: 902 110 572 (soporte.es@storex.eu)
Portugal: 308 800 836 (apoio.pt@support.eu)
England: (support.uk@storex.eu)
Monday to Thursday from 9:30 to 19:30.
Friday from 9:30 to 18:30.
33
34
35
Loading...