Stihl FH Instruction Manual

{

STIHL FH

Instruction Manual

Contents

English

Interchangeable Attachments 2
Guide to Using this Manual 2
Safety Precautions and Working

Techniques 3
Using the Unit 6
Approved Basic Power Tools 7
Mounting the Attachment 7
Adjusting the Cutter Bar 10

Original Instruction ManualPrinted on chlorine-free paper

Fitting the Harness 12
Starting / Stopping the Engine 13
Lubricating the Gearbox 14
Storing the Machine 15
Maintenance and Care 15
Sharpening Instructions 15
Minimize Wear and Avoid Damage 16
Main Parts 17
Specifications 18
Maintenance and Repairs 18
Disposal 19
EC Declaration of Conformity 19

Printing inks contain vegetable oils, paper can be recycled.

Dear Customer,

Thank you for choosing a quality
engineered STIHL product.

It has been built using modern
production techniques and
comprehensive quality assurance.
Every effort has been made to ensure
your satisfaction and troublefree use of
the product.

Please contact your dealer or our sales
company if you have any queries
concerning this product.

Your

Dr. Nikolas Stihl

{

© ANDREAS STIHL AG & Co. KG, 2017

0458-226-0121-B. VA1.B17.

0000007458_002_GB

FH

This instruction manual is protected by copyright. All rights reserved, especially the rights to reproduce, translate and process
with electronic systems.

1

English

.
.
.
.

002BA531 KN

+

+

Interchangeable
Attachments

The STIHL interchangeable attachment
may be mounted to different STIHL
power tools.

This includes KombiAttachmentEngines
in some markets. In these markets the
KombiAttachmentEngines and
interchangeable attachments are part of
the KombiAttachmentSystem.

The approved power tool models are
listed in the chapter on "Approved Basic
Power Tools".

In this instruction manual the functional
unit formed by the basic power tool and
interchangeable attachment is referred
to as the power tool.

Therefore, the separate instruction
manuals for the basic power tool and
attachment should be used together for
the power tool.

Always read and and make sure you
understand both instruction manuals
before using your power tool for the first
time and keep them in a safe place for
future reference.

Guide to Using this Manual

Pictograms

All the pictograms attached to the
machine are shown and explained in this
manual.

Symbols in text

WARNING

Warning where there is a risk of an
accident or personal injury or serious
damage to property.

NOTICE

Caution where there is a risk of
damaging the machine or its individual
components.

Engineering improvements

STIHL's philosophy is to continually
improve all of its products. For this
reason we may modify the design,
engineering and appearance of our
products periodically.

Therefore, some changes, modifications
and improvements may not be covered
in this manual.

2

FH

English

Safety Precautions and
Working Techniques

Because a power scythe
is a high-speed, fast-cut
ting power tool with very
sharp cutting blades and
a long reach, special
safety precautions must
be observed during
operation.

Always read and and
make sure you under
stand both instruction
manuals (basic power
tool and attachment)
before using your power
tool for the first time and
keep them in a safe place
for future reference. Non­observance of the safety
precautions may result in
serious or even fatal
injury.

Lend or rent your power tool only to
persons who are familiar with this model
and its operation – and only with the
instruction manuals of the basic power
tool and attachment.

Use your power scythe only for cutting
grass, scrub, shrubs, thicket, bushes
and similar materials.

Do not use your power tool for any other
purpose because of the increased risk of
accidents.

Only use cutting blades and accessories
that are explicitly approved for this
power tool by STIHL or are technically
identical. If you have any questions in
this respect, consult a servicing dealer.

-

Use only high quality tools and
accessories in order to avoid the risk of
accidents and damage to the machine.

STIHL recommends the use of genuine

-

STIHL tools and accessories. They are
specifically designed to match the
product and meet your performance
requirements.

Never attempt to modify your machine in
any way since this may increase the risk
of personal injury. STIHL excludes all
liability for personal injury and damage
to property caused while using
unauthorized attachments.

Do not use a pressure washer to clean
your power tool. The solid jet of water
may damage parts of the power tool.

Clothing and Equipment

Wear proper protective clothing and
equipment.

Clothing must be sturdy
but allow complete free
dom of movement. Wear
snug-fitting clothing, an
overall and jacket combi
nation, do not wear a
work coat.

Avoid clothing that could get caught on
branches or brush or moving parts of the
machine. Do not wear a scarf, necktie or
jewelry. Tie up and confine long hair
(e.g. with a hair net, cap, hard hat, etc.).

Wear steel-toed safety
boots with non-slip soles.

WARNING

To reduce the risk of eye
injuries, wear close-fit
ting safety glasses in
accordance with Euro
pean Standard EN 166.
Make sure the safety
glasses are a comforta
ble and snug fit.

Wear hearing protection, e.g. earplugs
or ear muffs.

Wear a safety hard hat for thinning
operations, when working in high scrub
and where there is a danger of head
injuries from falling objects.

Wear heavy-duty work
gloves made of durable
material (e.g. leather).

STIHL offers a comprehensive range of
personal protective clothing and
equipment.

-

Transporting the Power Tool

-

Always shut off the engine.

Always fit the blade guard (scabbard) –
even when you carry the unit for short
distances.

Move the cutter bar to the transport
position and make sure it is properly
engaged.

Carry the power tool properly balanced
by the drive tube – cutting blades behind
you.

-

-

-

FH

3

English

002BA055 KN

0000-GXX-1677-A0

5m (17ft)

To reduce the risk of serious burn
injuries, avoid touching hot parts of the
machine, including the gearbox housing.

Transporting by vehicle: Properly secure
your power tool to prevent turnover, fuel
spillage and damage.

Before Starting

Check that your power tool is properly
assembled and in good condition – refer
to appropriate chapters in the instruction
manuals of the basic power tool and
attachment.

– Cutting blades: Correctly

assembled, securely mounted and
in good condition (clean, move
freely, not warped), properly
sharpened and sprayed thoroughly
with STIHL resin solvent (lubricant).

– Never attempt to start the machine

in the transport position (cutter bar
folded against drive tube).

– Never attempt to modify the controls

or safety devices in any way.

– Keep the handles dry and clean –

free from oil and dirt – for safe
control of the power tool.

– Adjust shoulder strap and handles

to suit your height and reach. See
chapter on "Fitting the Harness".

To reduce the risk of accidents, do not
operate your power tool if it is damaged
or not properly assembled.

If you use a shoulder strap or full
harness: Practice removing and putting
down the machine as you would in an
emergency. To avoid damage, do not
throw the machine to the ground when
practicing.

Holding and Controlling the Power Tool

Always hold the power tool firmly with
both hands on the handles.

Make sure you have firm and secure
footing and hold the power tool so that
the cutting blades are always away from
your body.

Some versions of the machine can be
carried on a harness to relieve the
weight on the operator's arms.

Models with bike handle

Right handle on control handle, left hand
on left handle.

Models with loop handle

Right hand on control handle, left hand
on loop handle on drive tube, even if you
are left-handed. Wrap fingers and
thumbs firmly around the handles.

During Operation

In the event of impending danger or in
an emergency, switch off the engine
immediately by moving the slide control
/ stop switch/button to 0 or STOP.

This power tool is not
insulated against electric
shock. To reduce the risk
of electrocution, keep
well clear of electric
power lines.

To reduce the risk
of injury from mov
ing blades or falling
cuttings, do not
allow bystanders
within 5 meters of
your own position.

To reduce the risk of damage to
property, also maintain this distance
from other objects (vehicles, windows).

Make sure the idle speed setting is
correct. The cutting blades must not run
when the engine is idling with the throttle
trigger released. Check and correct the
idle speed setting regularly. If the cutting
blades still run when the engine is idling,
have your dealer check your machine
and make proper adjustments or repairs
– see instruction manual of basic power
tool.

Watch the cutting blades at all times – do
not cut areas of the bush or scrub that
you cannot see.

Be extremely careful when cutting high
scrub or bushes, check the other side
frequently for bystanders.

-

4

FH

English

The gearbox becomes
hot during operation. To
reduce the risk of burn
injury, do not touch the
gearbox housing.

Take special care in slippery conditions
(ice, wet ground, snow) – on slopes or
uneven ground.

Clear away fallen branches, scrub and
cuttings from the work area.

Watch out for obstacles: Roots and tree
stumps which could cause you to trip or
stumble.

Make sure you always have good
balance and secure footing.

When working at heights:

– Always use a lift bucket

– Never work on a ladder or in a tree

– Never work on an insecure support

– Never operate your power tool with

one hand

Be particularly alert and cautious when
wearing hearing protection because
your ability to hear warnings (shouts,
alarms, etc.) is restricted.

To reduce the risk of accidents, take a
break in good time to avoid tiredness or
exhaustion.

Work calmly and carefully – in daylight
conditions and only when visibility is
good. Stay alert so as not to endanger
others.

Inspect scrub and work area to avoid
damaging the cutting blades:

– Remove stones, rocks, pieces of

metal and other solid objects.

– When working close to the ground,

make sure that no sand, grit or
stones get between the blades.

– Take particular care when cutting

scrub or bushes next to or against
wire fences.

To avoid the risk of electrocution, do not
touch electric power lines – never cut
through electric power lines.

Do not touch the cutting
blades while the engine is
running. If the cutting
blades become jammed
by an object, switch off
the engine immediately
before attempting to
remove the object – there
is otherwise a risk of
injury.

Opening the throttle while the blades are
blocked increases the load and reduces
engine speed. The clutch then slips
continuously and this causes
overheating and damage to important
components (e.g. clutch, polymer
housing components) – and this can
increase the risk of injury from the
cutting blades moving while the engine
is idling.

If your power tool is subjected to
unusually high loads for which it was not
designed (e.g. heavy impact or a fall),
always check that it is in good condition
before continuing work – see also
"Before Starting". Make sure the safety
devices are working properly. Do not

continue operating your power tool if it is
damaged. In case of doubt, consult your
servicing dealer.

If the scrub is very dusty or dirty, spray
the blades with STIHL resin solvent from
time to time during cutting. This helps
greatly reduce blade friction as well as
the aggressive effects of sap and the
build-up of dirt particles.

Check the cutting attachment at regular
short intervals during operation or
immediately if there is a noticeable
change in cutting behavior:

– Shut off the engine.

– Wait until the cutting blades have

come to a complete standstill.

– Check condition and tightness, look

for cracks.

– Check sharpness.

After finishing work

After finishing work or before leaving the
unit unattended: Shut off the engine.

Always clean dust and dirt off the
machine – do not use any grease
solvents for this purpose.

Spray the blades with STIHL resin
solvent. Run the engine briefly so that
the solvent is evenly distributed.

Maintenance and Repairs

Service the machine regularly. Do not
attempt any maintenance or repair work
not described in the instruction manuals
of the basic power tool and attachment.
Have all other work performed by a
servicing dealer.

FH

5

English

225BA007 KN

STIHL recommends that you have
servicing and repair work carried out
exclusively by an authorized STIHL
servicing dealer. STIHL dealers are
regularly given the opportunity to attend
training courses and are supplied with
the necessary technical information.

Only use high-quality replacement parts
in order to avoid the risk of accidents
and damage to the power tool. If you
have any questions in this respect,
consult a servicing dealer.

STIHL recommends the use of genuine
STIHL replacement parts. They are
specifically designed to match your
model and meet your performance
requirements.

To reduce the risk of injury,always shut
off the engine before carrying out any
maintenance or repairs or cleaning the
machine.

Using the Unit

Do not use your power scythe during
other people's rest periods.

The power scythe is used at ground
level. As its blades operate like a mower
bar, the unit is ideal for cutting scrub,
thicket, reed, wild growth and hard
grasses. The power scythe is
particularly suitable for applications in
busy areas, such as traffic islands or
parks, because cuttings are not caught
and thrown by the blades.

Disposal

Do not throw cuttings into the garbage
can – they can be composted.

Preparations

N Set cutter bar to required angle.
N Remove the blade scabbard.
N Start the engine.
N Put on the shoulder strap.
N Attaching Machine to Shoulder

Strap

Working Technique

Working position and method are the
same as for a brushcutter: Sweep the
cutter bar to and fro in an arc just above
the ground.

6

FH

English

002BA658 KN

413BA014 KN

Approved Basic Power Tools

WARNING

This interchangeable attachment is only
approved for use on a basic power tool
equipped with one of the following
handle systems:

– Bike handle

– Loop handle

Operation of this interchangeable
attachment is permitted only with the
following basic power tools:

Bike-handled or loop-handled machines

To retrofit the carrying ring – see "Fitting
the Carrying Ring".

The FH attachment is not approved for
use on machines with a short drive tube.

Mounting the Attachment

Preparations for Mounting the
Attachment

WARNING

To reduce the risk of injury, always shut
off the engine before converting the
basic power tool.

NOTICE

Make sure the work area is clean before
mounting or removing the attachment.

N Rest the power tool on the machine

support.

Removing the Protective Cap

If a cap is fitted on the end of the power
tool's drive tube:

– STIHLKA85R

– STIHL FS 91, FS 91 R, FS 111,

FS 111 R, FS 131, FS 131 R

WARNING

Combinations with basic power tools
other than those listed above are not
permitted since they may result in
accidents or serious personal injury.

To retrofit the loop handle see chapter
on "Mounting the Loop Handle".

FH

N Pull the protective cap off the end of

the drive tube and keep it in a safe
place.

7

English

002BA248 KN

228BA092 KN

BF

228BA090 KN

FCS

If the plug comes out of the drive tube
when you pull off the cap:

N Push the plug into the drive tube as

far as stop.

Removing the gearbox or attachment

Remove any existing gearbox or
interchangeable attachment from the
basic power tool.

FH/HL

FH/HL

FCS

228BA091 KN

228BA081 KN

FS

228BA086 KN

HT

228BA082 KN

SP

0000-GXX-1866-A0

228BA084 KN

FS

228BA083 KN

8

FH

SP 10

381BA015 KN

L

N Loosen the clamp screws (arrows)

on the gearbox housing – do not
remove them.

N Pull the gearbox off the drive tube.

If the drive shaft slips out of the tube
when you pull off the gearbox:

N Push the drive shaft into the tube.

Mounting the Gearbox

228BA085 KN

10

English

11

12

11

10

0000-GXX-1682-A0

The drive shaft must not project from the
tube more than L = 22 mm (7/8 in).

If dimension (L) is not correct:
N Apply slight pressure to the drive

shaft and rotate it slowly at the same
time until it can be pushed in to the
specified length.

FH

5

N Loosen the clamp screws (10).
N Push the gearbox (11) onto the

drive tube (5), turn the gearbox (11)
back and forth as necessary.

Once the end of the drive tube is

0000-GXX-1681-A0

inserted beyond the slot in the
clamp (12):

N Push the gearbox (11) fully home as

far as stop.

N Tighten down the clamp screws

moderately.

N Line up the gearbox (11) with the

powerhead.

N Tighten down the clamp screws

firmly.

9

English

2

A

0000-GXX-1680-A0

0000-GXX-1683-A0

145°

Models with Loop Handle

N Loosen the screws on the loop

handle.

N Align the loop handle (2) and move

it to the most comfortable position.

Distance A must not be more than A =
20 cm.

N Tighten down the screws on the

loop handle.

Fitting the Carrying Ring

A carrying ring is necessary if the power
tool is to be used with a shoulder
strap/harness. Not all versions of basic
power tools are equipped with a carrying
ring.

The carrying ring is available as a
special accessory and is mounted as
described below.

A

2

1

4

3

N Mount the carrying ring (1) about

5 cm (A) forward of the control
handle (2).

N Push the carrying ring (1) over the

drive tube.

N Insert the M5 nut (3) in the hex

recess in the carrying ring.

N Fit the M5x14 screw (4).
N Line up the carrying ring.
N Tighten down the screw firmly.

Adjusting the Cutter Bar

Angle Adjuster - 145°

0000-GXX-1850-A0

The angle of th cutter bar can be
adjusted upwards in 4 stages from 0°
(straight) to 55°, and downwards in 7
stages from 0° to 90° (right angle facing
down). There are therefore 12 possible
working positions.

WARNING

To reduce the risk of injury, carry out the
adjustment only when the cutting blades
are at a standstill – engine at idle speed.

WARNING

The gearbox gets hot during operation.
To reduce the risk of burn injury, do not
touch the gearbox.

10

FH

English

0000-GXX-1686-A0

1

2

3

WARNING

To reduce the risk of injury, never touch
the blades while making adjustments.

2

3

1

N Pull back the sliding sleeve (1) and

use the lever (2) to adjust the joint
by one or several holes.

N Release the sliding sleeve (1) and

make sure the lock pin engages the
quadrant (3).

Transport Position

moving the cutter bar to the transport
position or from the transport position to
the normal working position.

WARNING

The gearbox gets hot during operation.
To reduce the risk of burn injury, do not
touch the gearbox.

0000-GXX-1684-A0

N Shut off the engine.
N Fit the blade scabbard.
N Pull back the sliding sleeve (1) and

use the lever (2) to swing the joint
upwards – in direction of drive tube
– until the cutter bar is flat against
the drive tube.

N Release the sliding sleeve (1) and

make sure the lock pin engages the
quadrant (3).

The cutter bar can be folded flat against
the drive tube and locked in position to
save space during transportation.

WARNING

To reduce the risk of injury, always shut
off the engine – depress stop switch –
and fit the blade scabbard before

FH

0000-GXX-1685-A0

11

English

1

002BA374 KN

2

1

002BA307 KN

2

3

1

002BA660 KN

2

1

1

2

2

Fitting the Harness

The type and style of the harness and
carabiner (spring hook) depend on the
market.

Shoulder Strap

Full Harness

N Put on the full harness (1).
N Adjus t the l engt h of th e stra p so th at

the carabiner (2) is about a hand’s
width below your right hip.

N Close the locking plate (3).

Attaching Machine to Harness

The type and style of the harness and
carabiner (spring hook) depend on the
market.

N Attach the carabiner (1) to the

carrying ring (2) on the drive tube.

N Put on the shoulder strap (1).
N Adjust the length of the strap so that

the carabiner (2) is about a hand’s
width below your right hip.

12

FH

English

002BA661 KN

2

1

1

1

2

2

002BA038 KN

002BA072 KN

Disconnecting Machine from Harness

N Press down the bar on the

carabiner (1) and pull the carrying
ring (2) out of the carabiner.

Throwing Off the Machine

If you are using a shoulder strap:
Practice slipping the strap off your
shoulder.

If you are using a full harness: Practice
quickly opening the locking plate and
slipping the harness straps off your
shoulders.

Starting / Stopping the
Engine

Starting the Engine

Always follow the starting procedure
described in the basic power tool
instruction manual.

WARNING

The machine must be quickly thrown off
in the event of imminent danger.
Practice removing and putting down the
machine as you would in an emergency.
To avoid damage, do not throw the unit
to the ground when practicing.

Practice quickly detaching the power
tool from the carabiner as described
under "Disconnecting Machine from
Harness".

FH

N Position the unit securely for

starting: It must rest on the machine
support and the blade gearbox.

N On units with adjustable cutter bar:

Set the cutter bar to the straight (0°)
position.

N Remove the blade scabbard. Check

that the cutting blades are not
touching the ground or any other
obstacles. If necessary, rest the
gearbox on a raised support (e.g.
mound, brick or something similar).

13

English

N Make sure you have a safe and

secure footing.

N Hold the unit firmly on the ground

with your left hand and press down
– do not touch the throttle trigger or
trigger interlock.

NOTICE

Do not stand or kneel on the drive tube.

WARNING

The cutting attachment may begin to
move as soon as the engine starts. For
this reason, blip the throttle after starting
– the engine returns to idling speed.

Now follow the starting procedure
described in the basic power tool
instruction manual.

Stopping the Engine

N See basic power tool instruction

manual.

Lubricating the Gearbox

Blade Drive Gear

Lubricate the blade drive gear with
STIHL gear lubricant for hedge trimmers
– see "Special Accessories".

1

N Check the lubricant level at regular

intervals of about every 25 hours of
operation. Unscrew the filler
plug (1) – if no grease can be seen
on the inside of the filler plug, screw
the tube of grease into the filler hole.

N Squeeze up to 10 g (2/5 oz) grease

into the gearbox.

NOTICE

Do not completely fill the gearbox with
grease.

N Unscrew the tube of grease from the

filler hole.

N Refit the filler plug and tighten it

down firmly.

Angle Drive Gear

Lubricate the angle drive gear with
STIHL gear lubricant for brushcutters
(special accessory).

2

N Check the lubricant level at regular

intervals of about every 25 hours of
operation. Unscrew the filler
plug (2) – if no grease can be seen
on the inside of the filler plug, screw
the tube of grease into the filler hole.

0000-GXX-1688-A0

N Squeeze up to 5 g (1/5 oz) grease

into the gearbox.

NOTICE

Do not completely fill the gearbox with
grease.

N Unscrew the tube of grease from the

filler hole.

N Refit the filler plug and tighten it

down firmly.

0000-GXX-1689-A0

14

FH

Storing the Machine Maintenance and Care Sharpening Instructions

English

For periods of 3 months or longer
N Clean the cutting blades, check

condition and spray them with
STIHL resin solvent.

N Fit the blade scabbard.
N Store the machine in a dry, high or

locked location – out of the reach of
children and other unauthorized
persons.

The following intervals apply to normal
operating conditions only. If your daily
working time is longer or operating
conditions are difficult (very dusty work
area, etc.), shorten the specified
intervals accordingly.

All accessible screws and nuts
N Check and retighten if necessary

(not screws and nuts on cutting
blades)

Cutting blades
N Visual inspection before starting

work

N Resharpen as necessary
N Replace if damaged

Gearbox lubrication

N Check before starting work
N Replenish as necessary

Safety labels
N Replace illegible safety labels

When cutting performance and behavior
begin to deteriorate, i.e. blades
frequently snag on branches:
Resharpen the cutting blades.

It is best to have the cutting blades
resharpened by a dealer on a workshop
sharpener. STIHL recommends a STIHL
servicing dealer.

NOTICE

Do not operate your machine with dull or
damaged cutting blades. This may
cause overload and will give
unsatisfactory cutting results.

FH

15

English

Minimize Wear and Avoid
Damage

Observing the instructions in this manual
and the basic power tool manual helps
reduce the risk of unnecessary wear and
damage to the power tool.

The power tool must be operated,
maintained and stored with the due care
and attention described in these
instruction manuals.

The user is responsible for all damage
caused by non-observance of the safety
precautions, operating and maintenance
instructions. This includes in particular:

– Alterations or modifications to the

product not approved by STIHL.

– Using tools or accessories which

are neither approved or suitable for
the product or are of a poor quality.

– Using the product for purposes for

which it was not designed.

– Using the product for sports or

competitive events.

– Consequential damage caused by

continuing to use the product with
defective components.

servicing dealer. STIHL dealers are
regularly given the opportunity to attend
training courses and are supplied with
the necessary technical information.

If these maintenance operations are not
carried out as specified, the user
assumes responsibility for any damage
that may occur. Among other parts, this
includes:

– Corrosion and other consequential

damage resulting from improper
storage.

– Damage to the product resulting

from the use of poor quality
replacement parts.

Parts Subject to Wear and Tear

Some parts of the power tool (e.g.
cutting blades) are subject to normal
wear and tear even during regular
operation in accordance with
instructions and, depending on the type
and duration of use, have to be replaced
in good time.

Maintenance Work

All the operations described in the
chapter on "Maintenance and Care"
must be performed on a regular basis. If
these maintenance operations cannot
be performed by the owner, they should
be performed by a servicing dealer.

STIHL recommends that you have
servicing and repair work carried out
exclusively by an authorized STIHL

16

FH

Main Parts

English

1 Cutting blades

1

2

6

5

3

4

2 Blade drive gear
3 Angle drive
4 Sliding sleeve
5 Quadrant
6 Adjusting lever
7 Blade guard (scabbard)

7

2

6

5

3

4

0000-GXX-1864-A0

FH

17

English

Specifications

Cutting blades

Type: Double-

edged for
bidirectional

cutting
Cutting length: 250 mm
Tooth spacing: 34 mm
Tooth height: 22 mm
Sharpening angle: 45° to

horizontal

Weight

Attachment: 1.5 kg

Noise and Vibration Data

Noise and vibration data measurements
on power tools with the HL attachment
include idling and rated maximum speed
in a ratio of 1:1.

For further details on compliance with
Vibration Directive 2002/44/EC see
www.stihl.com/vib.

Sound pressure level L

KA 85 R: 96 dB(A)
FS 91: 94 dB(A)
FS 91 R 93 dB(A)
FS 111: 94 dB(A)
FS 111 R: 93 dB(A)
FS 131: 98 dB(A)
FS 131 R: 98 dB(A)

to ISO 28868

p

Sound power level L

to ISO 22868

w

KA 85 R: 110 dB(A)
FS 91: 106 dB(A)
FS 91 R 106 dB(A)
FS 111: 106 dB(A)
FS 111 R: 106 dB(A)
FS 131: 110 dB(A)
FS 131 R: 110 dB(A)

Vibration measurement a

hv,eq

to

ISO 22867

2

-

Control
handle

4.9 m/s

2

2

2

2

2

2

2

Loop han
dle / bike

handle
KA 85 R: 5.5 m/s
FS 91: 4.8 m/s24.5 m/s
FS 91 R 4.4 m/s23.3 m/s
FS 111: 4.8 m/s24.5 m/s
FS 111 R: 4.4 m/s23.3 m/s
FS 131: 3.8 m/s24.2 m/s
FS 131 R: 6.1 m/s24.8 m/s

The K-factor in accordance with
Directive 2006/42/EC is 2.5 dB(A) for
the sound pressure level and sound
power level; the K-factor in accordance
with Directive 2006/42/EC is 2.0 m/s

2

for the vibration measurement.

REACH

REACH is an EC regulation and stands
for the Registration, Evaluation,
Authorisation and Restriction of
Chemical substances.

For information on compliance with the
REACH regulation (EC) No. 1907/2006
see www.stihl.com/reach.

Maintenance and Repairs

Users of this machine may only carry out
the maintenance and service work
described in this user manual. All other
repairs must be carried out by a
servicing dealer.

STIHL recommends that you have
servicing and repair work carried out
exclusively by an authorized STIHL
servicing dealer. STIHL dealers are
regularly given the opportunity to attend
training courses and are supplied with
the necessary technical information.

When repairing the machine, only use
replacement parts which have been
approved by STIHL for this power tool or
are technically identical. Only use high­quality replacement parts in order to
avoid the risk of accidents and damage
to the machine.

STIHL recommends the use of original
STIHL replacement parts.

Original STIHL parts can be identified by
the STIHL part number, the {
logo and the STIHL parts symbol K
(the symbol may appear alone on small
parts).

18

FH

English

000BA073 KN

Disposal

Observe all country-specific waste
disposal rules and regulations.

STIHL products must not be thrown in
the garbage can. Take the product,
accessories and packaging to an
approved disposal site for environment­friendly recycling.

Contact your STIHL servicing dealer for
the latest information on waste disposal.

EC Declaration of Conformity

ANDREAS STIHL AG & Co. KG
Badstr. 115
D-71336 Waiblingen

Germany

declare in exclusive responsibility that
the product

Category: Power scythe

attachment
Make: STIHL
Model: FH
Serial identification: 4243

conforms to the relevant provisions of
Directives 2006/42/EC and 2000/14/EC
and has been developed and
manufactured in compliance with the
following standards in the versions valid
on the date of production:

EN ISO 12100, EN ISO 11806-1 (in
conjunction with the specified FS and HL
models).

Technical documents deposited at:

ANDREAS STIHL AG & Co. KG
Produktzulassung (Product Licensing)

The year of manufacture is applied to
the power tool.

Done at Waiblingen, 28.10.2016

ANDREAS STIHL AG & Co. KG

Thomas Elsner

Director Product Management and
Services

FH

19

English

20

FH

0458-226-0121-B

englisch

G

www.stihl.com

*04582260121B*

0458-226-0121-B