State GS6 40 YBDS L User Manual

RESIDENTIAL

SELECT

DIRECT VENT RESIDENTIAL GAS WATER HEATERS

Diffuser Dip Tube

• Reduces lime and sediment buildup, maximizes hot water output

• Made of PEXAN™, a cross-linked PEX

Side-Mounted Taps Designed for Recirculating Systems

• Suitable for water heating and space heating

Direct Vent Design

• One-pipe, dual channel closed-combustion system draws all make-up air from outside the home, eliminating issues caused by insufficient indoor ventilation. Horizontal air intake and venting on all models up to 80 inches from outisde wall

Intelligent Control Logic

• The internal microprocessor provides enhanced operating parameters and tighter differentials for precise sensing and faster heating response to optimize performance

Self-Powered Electronic Gas Valve

• Uses a thermopile to generate the power needed to operate the electronic gas control without requiring an external power source

polymer that can withstand long-term exposure to water temperatures up to 400°F

Green Choice® “Eco-Friendly” GasBurner

• Patented design reduces NOx emissions by up to 33% compared to standard burners

Durable, Brass TamperResistant Drain Valve

Glasslined Tank

• For long-lasting protection against corrosion

Push Button Piezo Ignitor

• Simplifies lighting pilots with one-hand spark ignition

Anode Rods

•For added protection against corrosion

Factory-Installed CSA Certified and ASME Rated T&P Relief Valve

Diagnostics

• The electronic gas control incorporates an LED status indicator that monitors system operation and service diagnostics

Series 200/201

FVIR Compliant Design

For more information on Select®SL contact:

State Water Heaters 500 Tennessee Waltz Parkway Ashland City, TN 37015

1-800-365-0024 Toll-free USA www.statewaterheaters.com

Thick, “Environmentally-Friendly” Non-CFC Foam Insulation

• Reduces standby heat loss and improves efficiency

6-Year Limited Tank and Parts Warranty

Code Compliance - All models meet the Federal Energy Efficiency Standards effective January 20, 2004, according to the National Appliance Energy Conservation Act (NAECA) of 1992 and meets the thermal efficiency and standby loss requirements of the U.S. Department of Energy and current edition of ASHRAE/IESNA 90.1. Also complies with the current editions of the B.O.C.A. National Codes, C.E.C., U.B.C., S.B.C.C., C.A.B.O. and the H.U.D. standards.

SRGSS04712

RESIDENTIAL

SELECT®SL – DIRECT VENT RESIDENTIAL GAS WATER HEATERS

NUMBER

GS6 50 YBDS L

GS6 75 YBDS L

SERIESMODEL

200

GALLON

CAPACITY

40 0.60GS6 40 YBDS L

50 0.58

75 0.57

ENERGY FAC TOR

(EF)

BTU INPUT PER HOUR

NATURAL

RECOVERY

90°F RISE

BTU OUTPUT

PER HOUR

NATURAL

50,000 55 40,500 88 76 64-3/4 22-1/4 16-1/4 12-1/2 55-1/2 16-1/2 53-3/4 187

55,000 60 44,550 131 76 65-3/4 26-1/4 16-1/4 12-1/2 55-1/2 17-1/4 54 310

FIRST HOUR

RATING

*A B C D E F G H

68 54-3/4 22-1/4 16 12-1/4 45-1/4 16-1/2 41-3/4 167

Recoveries are rounded to nearest gallon Water Connections - 3/4” on all models Dual-channel system has 3” vent pipe inside 6” air intake pipe for the 40 & 50-gallon models. The 75-gallon model uses a 4”x7” Co-Axial Pipe. *A Dimension is to center line of flue (recommended vent height) When ordering propane, change “Y” to “H” in the model number (Example: GS6 40 HBDS L) Propane units are Series 201 All models have 2” foam cavity All 75-gallon water connections are 12” on center All models are certified from sea level to 7,700 ft. elevation

Optional Circulating Loop Fittings Package, Part No. 9002604005

25-1/4 FOR

40 & 50-GALLON

29-1/2 FOR 75-GALLON

Circulating Loop Fittings Package includes assembled di-electric unions and full port shut-off valves. A standard hose-connect drain valve is included for field installation. Specially designed for use on side tap recirculating water heaters. Kit must be ordered through Service Parts Department by calling 1-800-821-2017.

Important! Vent Installation and Termination Requirements

• Maximum horizontal vent distance is 80” to outside of exterior wall

• Minimum horizontal vent distance is 17” to outside of exterior wall

• Vent pipes may be trimmed (cut) for short vent installations

• For vent installation less than 30” the vent restrictor is required. Place restrictor over the flue outlet on heater before installing the outlet vent pipe to the heater

• Recommended installation height for the heater and vent pipe should be 68” for 40-gallon models and 76” for the 50 and 75gallon models (vent height)

• Offset Vent Arrangement

1. When replacing an existing direct vent model, the new vent pipe

may drop from the minimum vent height as much as 7-1/4” to exit through the existing vent opening in the exterior wall

2. Vent may have one horizontal 90° degree turn before exiting

through exterior wall (Do not combine both offset vent arrangements in one installation) (See examples in the installation manual)

• High Rise Vent Arrangement

3. When vent termination is more than 80” above the base of the heater. The horizontal vent runs must be a minimum of 22” from the center of the heater to the outside exterior wall surface. (See example in the installation manual)

• Vent termination clearance hole through the exterior wall should be approximately 7” diameter

• Snow accululation and drifting should be considered when locating the termination

• An optional wire grill vent cap protector is available through the parts department. Request part number 9006627005.

• See the installation manual for complete installation and venting requirements.

6“ DIA. ON THE 40 & 50-GALLON MODELS

7” DIA. ON THE 75-GALLON MODELS

FRONT

DIMENSIONS IN INCHES

TOP

MIN VENT

MAX VENT

SIDE TAPS

APPROX.

SHIPPING

WEIGHT

(LBS)

42°

47°

55°

69°

75-GALLON VENT

TERMINATION

CAP IS NOT

INTERCHANGEABLE

WITH THE VENT

CAP ON THE

40 & 50-GALLON

MODELS

EXTERIOR

WALL

For complete information on limited warranties, consult written warranty or contact technical support at 1-800-365-0024.

State Industries, Inc., reserves the right to make product changes or improvements without prior notice.

For more information on Select®SL contact:

State Water Heaters 500 Tennessee Waltz Parkway Ashland City, TN 37015

1-800-365-0024 Toll-free USA www.statewaterheaters.com