Star Manufacturing SST-12 Parts List

DRAWER ROLL/

BUN WARMER

MODEL

SST-12
SST-25

SST-45 & SST-45HC

Installation and

Operation

Instructions

2M-Y5049 Rev. H 8/01/05

SST-25

1

SAFETY SYMBOL

Using any part other than genuine Star factory supplied parts relieves the
manufacturer of all liability.

Star reserves the right to change specifi cations and product design without
notice. Such revisions do not entitle the buyer to corresponding changes,
improvements, additions or replacements for previously purchased
equipment.

Due to periodic changes in designs, methods, procedures, policies and
regulations, the specifi cations contained in this sheet are subject to change
without notice. While Star Manufacturing exercises good faith efforts to provide
information that is accurate, we are not responsible for errors or omissions
in information provided or conclusions reached as a result of using the
specifi cations. By using the information provided, the user assumes all risks in
connection with such use.

These symbols are intended to alert the user to the presence of
important operating and maintenance instructions in the manual
accompanying the appliance.

RETAIN THIS MANUAL FOR FUTURE REFERENCE

NOTICE

MAINTENANCE AND REPAIRS

Contact your local authorized service agent for service or required maintenance. Please record the model
number, serial number, voltage and purchase date in the area below and have it ready when you call to

ensure a faster service.

Model No.

Serial No.

Voltage

Purchase Date

Authorized Service Agent

Reference the listing provided with the unit

or

for an updated listing go to:

Website: www.star-mfg.com
E-mail [e-mail]
Telephone: [phone] Local [phone]

The Star Service Help Desk

Business 8:00 am to 4:30 p.m. Central Standard Time
Hours:

Telephone: [phone] Local [phone]

Fax: [phone] Local [phone]

E-mail [e-mail]

[e-mail]
[e-mail]

Website: www.star-mfg.com

Mailing Address: Star Manufacturing International Inc.

10 Sunnen Drive
St. Louis, MO 63143
U.S.A

2

2

This equipment is designed and sold for commercial use only by personnel trained and
experienced in its operation and is not sold for consumer use in and around the home nor
for use directly by the general public in food service locations. For equipment to be used by
the general public, please contact the factory.

CAUTION

INSTALLATION

This bun warmer is equipped for the voltage shown on the nameplate. It will operate on
alternating current only, however, the correct voltage must be applied.

CAUTION

DO NOT CONNECT TO DIRECT CURRENT (DC).

GENERAL OPERATING PROCEDURES

When you turn knob to temperature required, pilot light will go on until temperature in
warmer is reached, then pilot light will go off. The thermostat will automatically maintain
proper temperature, using current as needed. To shut off current, turn knob to left.

To keep rolls soft and fresh, turn knob to a low position. Higher settings should be used only
for short periods. The thermostat holds the temperature to which it is set. Keep the drawers
as full as possible. When adding new rolls to drawer, pull the rolls and buns that are left in
drawer toward the front and use them fi rst, giving time for new rolls to become heated. Do
not heat the rolls more than once, as they will not be palatable if reheated. If they dry out,
reduce temperature.

CORD, PLUG AND GROUND INSTRUCTIONS

For your protection, this appliance is equipped with a 3-conductor cord, with a grounding
type plug. Connect only to a grounding receptacle.

NOTE: This unit may smoke and have a slight odor when fi rst used because the insulation
is new. We suggest before using, you turn the thermostat to a high heat position and let unit

heat for approximately two (2) hours.

CLEANING

To remove the drawer for cleaning, fi rst pull the drawer out until it stops. Second,
remove the interior pan. Third, grasp the drawer assembly with both hands. Fourth,
lift the drawer in an upward direction, while slowly pulling out. This will disengage
the drawer from the drawer stops. To re-install the drawer, reverse the procedure.
For retaining the high lustre on the stainless steel, use a non-abrasive standard
stainless steel cleaner.

MAINTENANCE AND REPAIRS

Contact the factory, a service representative or a local service company for service or
required maintenance.

3