Sta-Rite CCHH User Manual

Straight Centrifugal Pumps

Optional

Flange and

Trap Packages

Available

The CC Series Pumps are com pact
and lightweight, but rugged.
Choose from 3 or 5 HP high
head and medium head models.
For lower pressures and maxi­mum capacity, medium head
models offer heads to 75 feet
and capac ities to 220 GPM.
Where higher pressures are
desired, the high head model
offers heads to 102 feet and
capacities to 260 GPM.

ORDERING INFORMATION

HIGH HEAD

Number HP Suct. Disch. Voltage* Phase Wt. Lbs.

CCHH 3 2-1/2" 2" 230 1 80
CCHH3 3 2-1/2" 2" 230/460 3 66
CCHJ 5 2-1/2" 2" 230 1 94
CCHJ3 5 2-1/2" 2" 230/460 3 80

MEDIUM HEAD

CCMH 3 2-1/2" 2" 230 1 80
CCMH3 3 2-1/2" 2" 230/460 3 66

Maximum load amps may vary with motor suppliers.
*200 Volt and 575 Volt models are available. Consult factory.

PRO-Source™ is a trademark of Pentair Water.
In order to provide the best products possible, specifications are subject to change.

Catalog

Pipe Tapping Sizes

APPLICATIONS

■

Water Systems

■

Sprinkling for homes, farms
and industry

Motor Approx.

CC series

SPECIFICATIONS

Body – Close-grained cast iron
Base – Heavy gauge steel
Impeller – Silicon brass (non-leaded)
Rugged Motors – 3 to 5 HP, 3450

RPM, open drip-proof, continuous
duty rated. 40°C ambient maximum,
NEMA series, JM construction.

Shaft – Carbon steel inside a
300 Series stainless steel sealed
remov able shaft sleeve.

Bearings – Permanently sealed ball
type, pre-lubricated.

Thermal Overload Protection –
Single-phase motors: automatic
reset; Three-phase motors: external
thermal protection required.

Max. Liquid Temperature – 125°F
Ambient Air Temperature – 104°F
Max. Pressure – 75 PSI

FEATURES

Compact and Lightweight – Can

be installed where most other 3 and
5 HP pumps will not fit… requires
just 11-3/8" x 18-1/2". Complete
pumps weigh only 66 to 94 lbs.

4-Position Discharge – Permits
installation with discharge hor i zon tal
or vertical, to right or left. Volute
features drain port which is func­tional when discharge is vertical.

Silicon Brass Impeller and
Wear Ring – Silicon brass impeller

is precision cast and machined.
Dynamically balanced for long seal life
and quiet operation. Non-overloading.
Contains no lead. Sil icon brass wear
ring is replaceable.

Easy Service – Back pull-out design:
entire motor may be re moved for
servicing impeller, seal or motor with ­out disturbing plumb ing. Centerline
discharge for ease of installation.

Shaft Seal – Mechan ical, ceramic
and carbon seal faces. Stainless steel
spring and Buna-N bellows.

Customer Service: [phone]

Fax Orders: [phone] www.sta-rite.com

•

1

Pentair Water

•

Delavan, WI 53115 USA

•

S4516WS (5/11)

•

Straight Centrifugal Pumps

04080 120 160 200 240 280

120

100

80

60

40

20

MIN 15'

MIN 15'

20'

22'

22'

22'

20'

20'

15'

10'

MIN 5'

CCHJ - 5 HP

CCMH - 3 HP

CCHH - 3 HP

CAPACITY GALLONS PER MINUTE

CAPACITY LITERS PER MINUTE

TOTAL HEAD IN METERS

TOTAL HEAD IN FEET

600 10004000 800200

35

30

25

20

15

10

5

0

J

3-13/16

F

B

(4) H

DIA. HOLES

K

P

1/4 NPT

C

1-13/16

2 NPT

6-3/8

10-9/16

4-3/16

3-11/16

D

6

N

8-3/8

3 -13/16

4-9/16

5/16-18 TAP

2-1/2 NPT

L

G

E

1/4 NPT

E

A

O

M

OUTLINE DIMENSIONS PUMP PERFORMANCE

CC series

Dimensions (in inches) are for estimating purposes only.

DIMENSIONAL DATA

Cat. No. A B C* D E F G* H* J K L M* N* O* P*

CCHH

CCMH

CCHH3

CCMH3

CCHJ

CCHJ3

*Dimensions may vary with motor supplier.

PUMP PERFORMANCE

HIGH HEAD

Cat.

No. HP PSI Head

20 46.2 148 142 134 125 120
CCHH 3 30 69.3 110 98 85 60 57
40 92.4 – – – – –
20 46.2 222 214 205 196 190
CCHJ 5 30 69.3 180 166 152 125 120
40 92.4 90 – – – –

Customer Service: [phone]

9 6-1/2 21-1/2 4-1/2 3-3/4 4-1/2 7/16 7/16 10-5/16 9-23/32 10-7/8 3/4 8-1/8 6-1/2 14-1/8

7 6 18-13/32 3-1/2 2-3/4 5 9/32 11/32 9-9/32 7-7/32 9-7/8 3/4 6-29/32 5-13/32 11

9 7-1/2 22-1/2 4-1/2 3-3/4 5-1/2 7/16 7/16 10-5/16 9-23/32 10-7/8 3/4 9 6-15/16 15-1/8

Disch. Pressure

Feet

(Capacity in Gallons Per Minute)

5' 10' 15' 20' 22'

Dynamic Suction Lift

•

Fax Orders: [phone] www.sta-rite.com

NOTE: Dotted lines indicate performance reduction at high

suction lift.

MEDIUM HEAD

Cat.

Disch. Pressure

No. HP PSI Head

Feet

Dynamic Suction Lift

5' 10' 15' 20' 22'

20 46.2 165 148 133 112 100
CCMH 3 30 69.3 – – – – –
40 92.4 – – – – –

Tested and rated in accordance with Water Systems Council
Standards.

NOTE: Pumps installed with a PRO-Source™ tank require a

100 PSI relief valve. Pumps installed with a conventional
tank require a 75 PSI relief valve. Relief valve must be
capable of relieving entire flow of pump at relief pressure.

2

Pentair Water

•

Delavan, WI 53115 USA

•

S4516WS (5/11)

•