Star TSP700 SERIES User Manual
THERMAL PRINTER
TSP700 SERIES
USER’S MANUAL
MODE D’EMPLOI
BEDIENUNGSANLEITUNG
MANUALE DI ISTRUZIONI
www.simple-shop.si
www.pos-systems.in
Federal Communications Commission
Radio Frequency Interference
Statement
This equipment has been tested and found to comply with the limits for a Class A digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the equipment is operated in a
commercial environment. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instruction manual, may cause
harmful interference to radio communications. Operation of this equipment in a residential
area is likely to cause harmful interference in which case the user will be required to correct
the interference at his own expense.
For compliance with the Federal Noise Interference Standard, this equipment requires a
shielded cable.
This statement will be applied only for the printers marketed in U.S.A.
Statement of
The Canadian Department of Communications
Radio Interference Regulations
This digital apparatus does not exceed the Class A limits for radio noise emissions from
digital apparatus set out in the Radio Interference Regulations of the Canadian Department
of Communications.
Le présent appareil numérique n’émet pas de bruits radioélectriques dépassant les limites
applicables aux appareils numériques de la classe A prescrites dans le Règlement sur le
brouillage radioélectrique édicté par le ministère des Communications du Canada.
The above statement applies only to printers marketed in Canada.
CE
Manufacturer’s Declaration of Conformity
EC Council Directive 89/336/EEC of 3 May 1989
This product, has been designed and manufactured in accordance with the International
Standards EN 50081-1/01.92 and EN 50082-1/01.92, following the provisions of the
Electro Magnetic Compatibility Directive of the European Communities as of May 1989.
EC Council Directive 73/23/EEC and 93/68/EEC of 22 July 1993
This product, has been designed and manufactured in accordance with the International
Standards EN 60950, following the provisions of the Low Voltage Directive of the
European Communities as of July 1993.
The above statement applies only to printers marketed in EU.
Trademark acknowledgments
TSP700: Star Micronics Co., Ltd.
ESC/POS: Seiko Epson Corporation
Notice
• All rights reserved. Reproduction of any part of this manual in any form whatsoever,
without STAR’s express permission is forbidden.
• The contents of this manual are subject to change without notice.
• All efforts have been made to ensure the accuracy of the contents of this manual at the
time of going to press. However, should any errors be detected, STAR would greatly
appreciate being informed of them.
• The above notwithstanding, STAR can assume no responsibility for any errors in this
manual.
©
Copyright 2001 Star Micronics Co., LTD.
TABLE OF CONTENTS
1. Parts Identification and Nomenclature .........................................................1
2. Consumable Parts and AC Adapter ..............................................................3
3. Connecting Cables and AC Adapter..............................................................5
3-1. Interface Cable .......................................................................................5
3-2. Connecting to a Peripheral Unit.............................................................7
3-3. Connecting the Optional AC Adapter ....................................................8
3-4. Turning Power On .................................................................................9
4. Control Panel and Other Functions.............................................................10
4-1. Control Panel .......................................................................................10
4-2. Errors ...................................................................................................10
4-3. Self Printing .........................................................................................12
5. Loading the Roll Paper .................................................................................13
6. Adjusting the Near-end Sensor ....................................................................16
7. Preventing and Clearing Paper Jams ..........................................................18
7-1. Preventing Paper Jams .........................................................................18
7-2. Removing Paper Jam ...........................................................................18
8. Periodical Cleaning .......................................................................................19
8-1. Cleaning the Thermal Head .................................................................19
8-2. Cleaning the Paper Holder ...................................................................19
Appendix A: Specifications...............................................................................80
A-1. General Specifications .........................................................................80
A-2. Auto Cutter Specifications ...................................................................81
A-3. Interface ...............................................................................................81
A-4. Electrical Characteristics .....................................................................81
A-5. Option...................................................................................................81
A-6. Environmental Requirements...............................................................82
A-7. Reliability.............................................................................................82
A-8. Black mark specifications ....................................................................83
Appendix B: Dip Switch Setting.......................................................................84
B-1. Parallel Interface Type.........................................................................85
B-2. Serial Interface Type............................................................................87
Appendix C: Parallel Interface ........................................................................90
Appendix D: Serial Interface............................................................................91
D-1. RS-232C Connector .............................................................................91
D-2. Cable Connections ...............................................................................93
D-3. Electrical Characteristics .....................................................................93
Appendix E: Periheral Unit Drive Circuit ......................................................94
Appendix F: Memory Switch Settings .............................................................95
Please access the following URL
http://www.star-micronics.co.jp/service/frame_sp_spr_e.htm
for the lastest revision of the manual.
ENGLISH
– 1 –
ENGLISH
1. Parts Identification and Nomenclature
Roll paper
User’s manual
Cover open lever
Pull this lever in the
direction of the
arrow to open the
printer cover.
Control panel
Features LED indicators to indicate printer
status and switches to
operate the printer.
Ferrite core Fastener
(Parallel interface
model only)
(Parallel interface
model only)
Printer cover
Open this cover to load or
replace paper.
Power connector
For connection of
the AC adapter.
Never unplug the
AC adapter while
the printer is on.
Peripheral drive connector
Connects to peripheral
units such as cash
drawers, etc.
Do not connect this to a
telephone.
Interface connector
For connection to a
host computer.
Power switch
Used to turn on/off
power to the printer.
– 2 –
ENGLISH
Choosing a place for the printer
Before actually unpacking the printer, you should take a few minutes to
think about where you plan to use it. Remember the following points
when doing this.
✓ Choose a firm, level surface where the printer will not be exposed to
vibration.
✓ The power outlet you plan to connect to for power should be nearby
and unobstructed.
✓ Make sure that the printer is close enough to your host computer for
you to connect the two.
✓ Make sure that the printer is not exposed to direct sunlight.
✓ Make sure that the printer is well away from heaters and other sources
of extreme heat.
✓ Make sure that the surrounding area is clean, dry, and free of dust.
✓ Make sure that the printer is connected to a reliable power outlet. It
should not be on the same electric circuit as copiers, refrigerators, or
other appliances that cause power spikes.
✓ Make sure that the room where you are using the printer is not too
humid.
– 3 –
ENGLISH
2. Consumable Parts and AC Adapter
When consumable parts have run out, use those specified in the table below.
Make sure that the AC adapter specified in the table is used.
Use of consumable parts or AC adapter which are not specified in the table may
result in damage to the printer, fire or electric shock.
(1) Roll paper specification
Thermal paper
Thickness: 65~150
µ
m
Width: 79.5±0.5 mm or 82.5±0.5 mm
Outer roll diameter: ø100 mm or less
Take up paper roll width: 80 mm or 83 mm
Core outer/inner diameter
Paper thickness Core outer Core inner
65~75
µ
m ø18±1 mm ø12±1 mm
65~75
µ
m ø32±1 mm ø25.4 mm
75~150
µ
m ø32±1 mm ø25.4 mm
Printed surface: Outer edge of roll
Tail end handling: Do not use paste or glue to secure the roll paper or
its core.
Do not fold the tail end of the paper.
(2) Recommended paper
Mitsubishi Paper Mills Limited
P220AG (normal type paper), 65 µm (thickness)
HP220A (high image stability paper), 65 µm (thickness)
HP220AB-1 (high image stability paper), 75 µm (thickness)
P220AB (normal type paper, card ticket), 85 µm (thickness)
P220AC-1 (normal type paper, card ticket), 95 µm (thickness)
P220AC (normal type paper, card ticket), 105 µm (thickness)
P220AD (normal type paper, card ticket), 130 µm (thickness)
P220AE-1 (normal type paper, card ticket), 150 µm (thickness)
Oji Paper Co., Ltd.
PD150R (normal type paper), 75 µm (thickness)
PD160R (high image stability paper), 65/75 µm (thickness)
Nippon Paper Industries
TF50KS-E2C (normal type paper), 65 µm (thickness)
Depending on the type and thickness of the paper, it may be necessary to change
the settings for printing darkness. To change the darkness settings, use the
printing darkness settings command <ESC><RS> ‘d’ n. Refer to the separate
programmer’s manual for details.
+0.5
-1
+0.5
-1
– 4 –
ENGLISH
(3) AC adapter (option)
Model name: PS60-24 A
Input: 100 to 240 V AC, 50/60 Hz
Output: DC24±5%, 2.0 A (5.0 A Load 10 sec. Max)
Important!
Access the following URL for the information of the recommended paper.
http://www.star-micronics.co.jp/
– 5 –
ENGLISH
3. Connecting Cables and AC Adapter
3-1. Interface Cable
3-1-1. Fer r ite Core Installation (Parallel interface model only)
(1)For only the parallel interface model,
affix the ferrite core onto the cable
as shown in the illustration below.
(2)Pass the fastener through the ferrite
core.
(3)Loop the fastener around the cable
and lock it. Use scissors to cut off
any excess.
Ferrite core
Interface cable
5 cm
maximum
Fastener
Pull and cut
– 6 –
ENGLISH
3-1-2. Connecting the Interface Cable
Note: Before connecting/disconnecting the interface cable, make sure that
power to the printer and all the devices connected to the printer is
turned off. Also make sure the power cable plug is disconnected from
the AC outlet.
(1)Connect the interface cable to the connector on the rear panel of the printer.
(2)In the case of a serial interface, tighten the connector screws. In the case of a
parallel interface, fasten the connector clasps.
Serial interface cable
Parallel interface cable
– 7 –
ENGLISH
3-2. Connecting to a Peripheral Unit
You can connect a peripheral unit to the printer using a modular plug. The
following describes how to install the ferrite core and make the actual connection.
See “Modular plug” on page 80 for details about the type of modular plug that is
required. Note that this printer does not come with a modular plug or wire, so it
is up to you to obtain one that suits your needs.
Important!
Make sure that the printer is turned off and unplugged from the AC outlet
and that the computer is turned off before making connections.
(1)Connect the peripheral drive cable to the connector on the rear panel of the
printer.
Important!
Do not connect a telephone line into the peripheral drive connector.
Failure to observe this may result in damage to the printer.
Also, for safety purposes, do not connect wiring to the external drive
connector if there is a chance it may carry peripheral voltage.
(2) Connect the ground wire. (Europe only)
Take out the screw shown in the figure below, then fasten the ground wire
terminal to the place where the screw was removed and tighten the screw.
Europe only
– 8 –
ENGLISH
3-3. Connecting the Optional AC Adapter
Note: Before connecting/disconnecting the AC adapter, make sure that
power to the printer and all the devices connected to the printer is
turned off. Also make sure the power cable plug is disconnected from
the AC outlet.
(1)Connect the AC adapter to the power cable.
Note: Use only the standard AC adapter and power cable.
(2)Connect AC adapter to the connector on the printer.
(3)Insert the power cable plug into an AC outlet.
Important!
When disconnecting the cable, take hold of the
cable connector to pull it out. Releasing the lock
makes it easy to disconnect the connector.
Pulling the cable excessively could cause damage to
the connector.
– 9 –
ENGLISH
Power switch
3-4. Turning Power On
Make sure that the AC adapter has been connected as described in 3-3.
(1)Set the power switch located on the front of the printer to on.
The POWER lamp on the control panel will light up.
Important!
We recommend that you unplug the printer from the power outlet
whenever you do not plan to use it for long periods. Because of this, you
should locate the printer so that the power outlet it is plugged into is
nearby and easy to access.
– 10 –
ENGLISH
4. Control Panel and Other Functions
4-1. Control Panel
1 POWER lamp (Green LED)
Lights when the power is ON
2 ERROR lamp (Red LED)
Indicates various errors in combination with POWER lamp
3 FEED button
Press the FEED button to feed roll
paper.
4-2. Errors
1) Automatically recoverable error
2) Recoverable error
Note
1) If the cutter doesn’t return to the home position, or doesn’t perform the
initial movement, it cannot be recovered.
2) If the paper is jammed, turn the power off, clear the jammed paper, then
turn the power ON.
POWER lamp
Flashes at 0.5 sec-
ond intervals
On
Recovery Conditions
Automatically recovered after the
print head has cooled.
Automatically recovered by closing
the printer cover.
Error Description
Head high tem-
perature detection
Cover open error
ERROR lamp
Off
On
POWER lamp
Off
Recovery Conditions
Recovered If the cutter returns to the
home position after turning the power
OFF and ON.
Error Description
Paper cut error
ERROR lamp
Flashes at 0.125
second intervals
1 POWER lamp (Green LED)
3 FEED button
2 ERROR lamp
(Red LED)
– 11 –
ENGLISH
3) Non recoverable error
Note
1) If a non recoverable error occurs, turn the power OFF immediately.
2) When Power supply error occurs, there is a possibility that the power
supply unit has a trouble.
For other non recoverable errors, please consult the dealer for repairs.
4) Paper detection error
POWER lamp
Off
Flashes at 0.25
second intervals
Flashes at 0.5 second intervals
Flashes at 1 second intervals
Recovery Conditions
This is not a recoverable error.
Consult dealer for repairs.
This is not a recoverable error.
Consult dealer for repairs.
This is not a recoverable error.
Consult dealer for repairs.
Error Description
RAM error
Memory SW error
Thermistor error
Power supply error
ERROR lamp
On
Flashes at 0.25
second intervals
Flashes at 0.5 second intervals
Flashes at 1 second intervals
POWER lamp
On
On
Recovery Conditions
Automatically recovered by loading
a new paper roll, then closing the
printer cover.
Indicators show that the paper end is
approaching, but the printer continues to print.
Error Description
Paper out error
Paper near end
ERROR lamp
Flashes at 0.5 sec-
ond intervals
Flashes at 2 second intervals
– 12 –
ENGLISH
4-3. Self Printing
(1)Test Printing
Turn the power on while holding the FEED button depressed.
Test printing will be performed according to the Ver. No., DIP switch settings
and character order. When the FEED button is depressed at the time of the end
of test printing, only the characters will be printed out repeatedly.
(2) Hexadecimal Dump Mode
Open the printer cover, then turn the power on while holding the FEED button.
When the cover is closed, “*** HEX DUMP PRINTING ***” is printed, and
the printer enters the Hexadecimal Dump Mode.
Each of the signals sent from the computer to the printer will be printed out
in hexadecimal code.
This function allows you to check if a control code sent to the printer by the
program being used is correct or not. The final line is not printed if its data is
less than one full line. However, if the FEED button is pushed, the final line
is printed. To turn off the mode, it is necessary to turn off the printer
completely.
– 13 –
ENGLISH
5. Loading the Roll Paper
Be sure to use roll paper that matches the printer’s specification.
When using a paper roll with an 82.5 mm width, remove the paper roll holder as
described on the following page.
Push the Cover open lever, and open
the printer cover.
While observing the direction of the
roll, set the paper roll into the hollow,
and pull on the leading edge of the
paper toward you.
Note 1: When using paper with a thickness which requires the use of the tension bar (65
µ
m paper thickness<100
µ
m), be sure not to pass the paper under
the tension bar.
Cover open lever
Roll paper
Tension bar
– 14 –
ENGLISH
Note 2: When using paper with a thickness which does not require the use of
the tension bar (100
µ
m paper thick-
ness
150 µm), remove the tension bar
unit by removing the clips at both ends
of the bar with a flat head screwdriver.
Then, lower the right and left adjustment levers by unhooking them with a
flat head screwdriver first, then lowering them to the proper position.
Ordinarily, your dealer should have
already done these procedures.
Note: When using a paper roll with an
82.5 mm width, be sure to remove the
paper roll holder.
Paper roll holder
– 15 –
ENGLISH
Important!
1. Do not touch the cutter blade.
· There is a cutter inside the paper outlet slot. Not only should you not
put your hand in the paper outlet slot while printing is in progress,
never put your hand into the outlet even when printing is not in
progress.
· The printer cover can be opened when replacing the paper. However, since the cutter blade is on the inside of the printer cover, be
careful not to place your face or hands too close to the cutter blade.
2. Do not operate the cover open lever while pressing on the printer
cover with your hand.
3. Do not pull out paper while the printer cover is closed.
4. The heating element and the driver IC of the thermal head are easily
damaged. Do not touch them with metal objects, sandpaper, etc.
5. During and immediately after printing, the area around the thermal
head is very hot. Do not touch it, as you could be burned.
6. Printing quality may suffer if the thermal head heating element
becomes soiled by being touched with your hands. Do not touch the
thermal head heating element.
7. There is a risk of damage to the driver IC of the thermal head from
static electricity. Never directly touch the IC.
8. The printing quality and working life of the thermal head cannot be
guaranteed if any paper other than that recommended is used. In
particular, paper containing [Na+, K+, C1-] may drastically reduce
the working life of the thermal head. Please exercise caution.
9. Do not operate the printer if there is moisture on the front surface of
the head from condensation, etc.
Push down both sides of the printer
cover to close.
Note: Make sure that the printer cover
is securely closed.
– 16 –
ENGLISH
6. Adjusting the Near-end Sensor
Use the following procedure to adjust the near-end sensor so it is compatible with
the size of roll paper you are using.
1 Open the printer cover.
2 Determine the diameter of the roll paper you are using and find the required
setting in the table below.
3 Insert the tip of a ballpoint pen or similar object into the hole of the adjuster,
and then push and side the adjuster to the desired setting.
When changing the setting, make sure that the position of the hole is aligned
with the alignment mark indicated by the arrow.
(Level 1) (Level 2) (Level 3)
– 17 –
ENGLISH
Adjustment value according to the paper you are using
Note
1) The standard model is set to level 1
prior to being shipped from the factory.
2) The C dimension and the remained
paper length are the calculated values. There may be some variations
in actual mechanism.
3) If thick paper is used (100 µm
paper
thickness
150 µm there will be
looseness in the roll paper itself
which makes it easier for detection
variations to occur. Set to Level 3.
When using the paper roll with a core whose inside diameter (A):ø12, outside diameter
(B):ø18
Level 1 Level 2 Level 3 Level 1 Level 2 Level 3
ø23 ø27 ø31 2.5 4.9 7.7
2.1 4.2 6.7
Paper thick-
ness (
µ
m)
65
75
Remained paper length
(Approx. m)
Detected diameter (C)
(Approx. mm)
When using the paper roll with a core whose inside diameter (A): ø25.4, outside
diameter (B):ø32
Level 1 Level 2 Level 3 Level 1 Level 2 Level 3
ø36 ø40 ø44 2.8 6.4 10.4
2.4 5.5 9.0
2.1 4.9 7.9
1.9 4.4 7.1
1.7 4.0 6.4
1.4 3.2 5.2
1.2 2.8 4.5
Paper thick-
ness (
µ
m)
65
75
85
95
105
130
150
Remained paper length
(Approx. m)
Detected diameter (C)
(Approx. mm)
C
C
B
A
Roll paper core
– 18 –
ENGLISH
7. Preventing and Clearing Paper Jams
7-1. Prev enting Paper Jams
The paper should not be touched during ejection and before it is cut.
Pressing or pulling the paper during ejection may cause a paper jam, paper cutting
failure or line feed failure.
7-2. Removing Paper Jam
If a paper jam occurs, clear it as described below.
(1)Set the power switch to off to turn off power to the printer.
(2)Pull the lever toward you to open the printer cover.
(3)Remove the jammed paper.
Note: Take care not to damage the printer when removing the jammed paper.
Since it is easy to damage the thermal head in particular, take care not
to touch it.
(4)Position the roll paper straight and close the printer cover gently.
Note 1: Make sure that the paper is positioned straight. If the printer cover
is closed with the paper skewed, a paper jam may result.
Note 2: Lock the printer cover by pressing down on the sides. Do not try to
close it by pressing down on the center. The cover may not lock
properly.
(5)Set the power switch to on to turn on power to the printer. Make sure that the
ERROR LED is not lit.
Note: While the ERROR LED is lit, the printer will not accept any commands
such as the print command, so make sure that the printer cover is locked
properly.
– 19 –
ENGLISH
8. Periodical Cleaning
Printed characters may become partially unclear due to accumulated paper dust
and dirt. To prevent such a problem, paper dust collected in the paper holder and
paper transport section and on the surface of the thermal head must be removed
periodically. Such cleaning is recommended to be carried out once six month or
one million lines.
8-1. Cleaning the Thermal Head
To remove blackish dust collected on the surface of the thermal head, wipe it with
Isopropyl alcohol (IPA).
Note: The thermal head is easy to damage, so clean it gently with a soft cloth.
Take sufficient care not to scratch it when cleaning it.
8-2. Cleaning the Paper Holder
Use a soft cloth to remove paper dust from the paper holder and paper transport
section.
– 20 –
FRANÇAIS
TABLE DES MATIERES
1. Identification des pièces et nomenclature....................................................21
2. Consommables et adaptateur secteur ..........................................................23
3. Câbles de connexion et adaptateur secteur .................................................25
3-1. Câble d’interface ..................................................................................25
3-2. Raccordement d’un appareil périphérique ...........................................27
3-3. Connexion de l’adaptateur secteur optionnel.......................................28
3-4. Mise sous tension de l’imprimante ......................................................29
4. Panneau de commande et autres fonctions .................................................30
4-1. Panneau de commande.........................................................................30
4-2. Erreurs ..................................................................................................30
4-3. Auto-impression...................................................................................32
5. Chargement du rouleau de papier ...............................................................33
6. Réglage du capteur de fin de rouleau ..........................................................36
7. Prévention et correction de bourrages de papier .......................................38
7-1. Prévention des bourrages de papier .....................................................38
7-2. Correction de bourrages de papier .......................................................38
8. Nettoyage ........................................................................................................39
8-1. Nettoyage de la tête d’impression ........................................................39
8-2. Nettoyage du support de papier ...........................................................39
APPENDICE......................................................................................................80
L’appendice n’est pas traduit.
Pour obtenir la dernière version de ce manuel, consultez l’adresse URL suivante:
http:/www.star-micronics.co.jp/service/frame_sp_spr_e.htm.
– 21 –
FRANÇAIS
1. Identification des pièces et nomenclature
Rouleau de papier Mode d’emploi
Levier d’ouverture du capot
Tirez ce levier dans le sens de
la flèche pour ouvrir le capot
de l’imprimante.
Panneau des commandes
Le panneau est équipé de
commutateurs permettant la
commande de l’imprimante et
de DELs indiquant les statuts.
Tore de ferrite Attache
(Modèle avec interface
parallèle seulement)
(Modèle avec interface
parallèle seulement)
Capot de l’imprimante
Ouvrez ce capot pour charger
ou remplacer le papier.
Interrupteur d’alimentation
Permet la mise sous et
hors tension de l’appareil.
Connecteur
d’interface
Ce connecteur
vous permet de
connecter
l’imprimante à
l’ordinateur-hôte.
Connecteur d’appareil
périphérique
Ce connecteur vous
permet de raccorder
l’imprimante à des
appareils périphériques
tels que des tiroirscaisses, etc.
Ne pas raccorder à un
téléphone.
Connecteur
d’alimentation
Ce connecteur
vous permet de
connecter le câble
de l’adaptateur
secteur. Ne
déconnectez pas
le câble lorsque
l’imprimante est
sous tension.
– 22 –
FRANÇAIS
Emplacement de l’imprimante
Avant de déballer l’imprimante, déterminez l’emplacement où vous
souhaitez l’installer. Veuillez observer les points ci-dessous lors de votre
choix.
✓ Choisissez une surface stable et de niveau sur laquelle l’imprimante
ne sera exposée à aucune vibration.
✓ Assurez-vous que l’emplacement dispose d’une prise secteur proche
et d’accès aisé.
✓ Assurez-vous que la distance entre l’imprimante et l’ordinateur-hôte
vous permet de les raccorder aisément.
✓ Assurez-vous que l’imprimante n’est pas exposée directement aux
rayons du soleil.
✓ Tenez l’imprimante à l’écart des sources de chaleur importante, telles
que les appareils de chauffage, etc.
✓ Assurez-vous que le lieu où vous souhaitez installer l'imprimante est
propre, sec et n'est pas poussiéreux.
✓ Assurez-vous que la prise secteur à laquelle vous raccordez l’impri-
mante délivre une tension stable. Evitez de raccorder l’imprimante à
la prise secteur d’un circuit alimentant de gros consommateurs de
courant, tels qu’un photocopieur, réfrigérateur, etc.
✓ Assurez-vous que le lieu où vous installez l’imprimante n’est pas
excessivement humide.
– 23 –
FRANÇAIS
2. Consommables et adaptateur secteur
Il convient d’utiliser exclusivement les types de papier figurant dans le tableau cidessous. Veillez également à utiliser l’adaptateur secteur qui figure dans le tableau.
L’utilisation d’un type de papier et d’adaptateur ne figurant pas dans le tableau risque
d’endommager l’imprimante, de causer un incendie ou une décharge électrique.
(1) Rouleau de papier, caractéristiques
Papier thermique
Épaisseur: 65~150 µm
Largeur: 79,5±0,5 mm or 82,5±0,5 mm
Diamètre extérieur du rouleau: ø100 mm or less
Largeur du rouleau de papier: 80 mm 83 mm
Diamètre extérieur/intérieur du support de rouleau
Épaisseur du papier Extérieur du support de rouleau Intérieur du support de rouleau
65~75 µm ø18±1 mm ø12±1 mm
65~75 µm ø32±1 mm ø25,4 mm
75~150 µm ø32±1 mm ø25,4 mm
Surface imprimée: Bord extérieur du rouleau
Extrémité arrière: Ne pas utiliser de colle pour immobiliser le rouleau
de papier ou son noyau.
Ne pas plier l’extrémité arrière du papier.
(2) Papier conseillé
Mitsubishi paper mills limited
P220AG (papier de type normal), 65 µm (épaisseur)
HP220A (papier à stabilité d’image élevée), 65 µm (épaisseur)
HP220AB-1 (papier à stabilité d’image élevée), 75 µm (épaisseur)
P220AB (papier de type normal, ticket), 85 µm (épaisseur)
P220AC-1 (papier de type normal, ticket), 95 µm (épaisseur)
P220AC (papier de type normal, ticket), 105 µm (épaisseur)
P220AD (papier de type normal, ticket), 130 µm (épaisseur)
P220AE-1 (papier de type normal, ticket), 150 µm (épaisseur)
Oji paper Co., Ltd.
PD150R (papier de type normal), 75 µm (épaisseur)
PD160R (papier à stabilité d’image élevée), 65/75 µm (épaisseur)
Nippon paper industries
TF50KS-E2C (papier de type normal), 65 µm (épaisseur)
Suivant le type et l’épaisseur du papier, il peut être nécessaire de changer le
réglage de clarté d’impression. Pour changer le réglage de la clarté d’impression,
utilisez la commande de réglage de clarté d’impression <ESC><RS>‘d’n.
Reportez-vous au manuel de programmation séparé pour les détails.
+0,5
-1
+0,5
-1
– 24 –
FRANÇAIS
(3) Adaptateur secteur (option)
Nom du modèle: PS60-24 A
Entrée: CA100 à 240 V, 50/60 Hz
Sortie: CC24±5%, 2,0 A (charge de 10 sec à 5,0 A max.)
Attention!
Pour obtenir des informations concernant le papier recommandé, consultez l’adresse URL suivante : http://www.star-micronics.co.jp/.
– 25 –
FRANÇAIS
3. Câbles de connexion et adaptateur secteur
3-1. Câble d’interface
3-1-1. Installation du tore de ferrite (modèle avec interface
parallèle seulement)
(1)Modèle avec interface parallèle seu-
lement: fixez la grande gaine en
ferrite sur le câble comme illustré.
(2)Passez l’attache dans le tore de fer-
rite.
(3) Passez l’attache autour du tore de
ferrite et serrez-la. Coupez l’extrémité de l’attache à l’aide de ciseaux.
Tore de ferrite
Interface câble
5 cm
maximum
Attache
Tirez et coupez
– 26 –
FRANÇAIS
3-1-2. Connexion du câble d’interface
Remarque:Avant de connecter ou déconnecter le câble d’interface, veillez à
ce que l’imprimante et tous les appareils qui y sont connectés
soient hors tension. Veillez également à débrancher le câble
d’alimentation de la prise secteur.
(1)Connectez le câble d’interface à la borne figurant sur le panneau arrière de
l’imprimante.
(2)Dans le cas d’une interface série, resserrez les vis du connecteur. Dans le cas
d’une interface parallèle, fixez le connecteur avec les fermoirs.
Câble d’interface série
Câble d’interface parallèle
– 27 –
FRANÇAIS
3-2. Raccordement d’un appareil périphérique
Vous pouvez raccorder un appareil périphérique à l’imprimante à l’aide d’une
fiche modulaire. Nous expliquons ci-dessous comment installer le tore de ferrite
et faire le raccordement proprement dit. Pour les détails sur le type de fiche
modulaire à utiliser, reportez-vous à la page 94. Notez que le fil ou la fiche
modulaires ne sont pas fournis avec l’imprimante. Vous devrez donc vous les
procurer.
Attention!
Assurez-vous que l’imprimante est hors tension, qu’elle est débranchée
de la prise secteur et que l’ordinateur est hors tension avant d’effectuer
les connexions.
(1)Connectez le câble de pilote de périphérique à la borne figurant sur le panneau
arrière de l’imprimante.
Attention!
Ne connectez pas une ligne de téléphone à la borne du pilote de
périphérique, sous peine de risquer d’endommager l’imprimante.
Pour des raisons de sécurité, il convient également de ne pas brancher
d’appareil périphérique en cas de risque de survoltage.
(2) Attachez le fil de mise à la terre. (Europe seulement)
Déposez la vis indiquée dans le schéma ci-dessous, puis attachez la borne du
fil de mise à la terre à l’endroit occupé précédemment par la vis et resserrez
la vis.
Europe seulement
Loading...