Stamina 55-1530, 55-1530A User Manual

READ AND FOLLOW THE WARNINGS AND INSTRUCTIONS IN THIS OWNER’S MANUAL.

ANY PREVIOUSLY PROVIDED OWNER’S MANUALS OR INSTRUCTIONAL DVD THAT
ACCOMPANIED THIS PRODUCT OR CONTAINED HEREIN SHOULD BE DISCARDED AND
REPLACED WITH THIS UPDATED VERSION. REFER TO PAGE 5 FOR INSTRUCTIONS ON

WHERE TO AFFIX THE NEW INVERSION WARNING DECAL.

Owner's

Manual

!

WARNING

Exerci s e can presen t a
h e a l t h r i s k . C o n s u l t a
physician before beginning
any exercise program with
this equipment. If you feel
faint or dizzy, immediately
discontinue use o f th i s
equipment. Serious bodily
in j u r y c a n occur if thi s
equipment is not assembled
and used correctly. Serious
bodily injury can also occur
if all instructions are no t
followed. Keep others and
pets away from equipment
when in use. Always make
sure all bolts and nuts are
securely tightened prior to
each use. Follow all safety
instructions in this manual.

Product May Vary Slightly From Pictured.

WARNING: The Buckle Strap and the Nylon Strap must be

attached and properly adjusted at all times during
use of this product.

CAUTION: Weight on this product should not exceed 250 lbs.

This Product is Distributed Exclusively by

2040 N. Alliance, Springeld, MO 65803

Customer Service

1 [phone]

www.staminaproducts.com

When calling for parts or

service, please specify

the following number

:

Model#: 55-1530,

55-1530A

STAMINA PRODUCTS

MADE IN CHINA

2011 Stamina Products, Inc.

©

2011, 03

TABLE OF CONTENTS

Safety Instructions ...................................... 2

Before You Begin ........................................ 4

Equipment Warning, Caution & Notice Labels ... 5

Hardware Identication Chart .................... 6

Assembly Instructions ................................ 7

Operational Instructions ........................... 11

Storage ....................................................... 14

Maintenance ............................................... 14

Warranty ..................................................... 15

Product Parts Drawing .............................. 16

Parts List .................................................... 17

Fax/Mail Ordering Form ............................ 18

SAFETY INSTRUCTIONS

!

WARNING

!

WARNING

Read all warnings and cautions posted on the Inversion Stretch System.

1.
The Inversion Stretch System should only be used after a thorough review of the Owner’s Manual.

2.
Make sure that the Inversion Stretch System is properly assembled before use. We recommend that two people be available

3.
for assembly of this product.
Do not use the Inversion Stretch System alone. Always have a helper available in case assistance is needed in recovering

4.
from the inverted position.

Verify that adequate head clearance is available between the user’s head and the oor before using this inversion table. This

5.
is especially important for tall users.
Make sure that the Pivot Arms are assembled to the Main Frame using the same position hole in each Pivot Arm. Pay close

6.
attention to Steps 3 and 4 on page 8.
Make sure that the Pivot Arms are always secured to the pegs on the Main Frame with the Bolts and Washers.

7.
Adjust the Nylon Straps to limit the Main Frame rotation to an angle of 15 to 20 degrees from the top position and use this setting

8.
until you have veried your height setting and become familiar with the Inversion Stretch System.
Use the lowest holes in the Pivot Arms until you become familiar with the Inversion Stretch System.

9.
DO NOT ALLOW table to invert past vertical. Table inverting past vertical may result in table contacting frame, damage to table

10.
and serious injury to user due to fall hazard. Prior to each use, make sure nylon and buckle straps are securely attached, as
instructed in Steps 9 and 10 on page 10. Adjust straps to desired angle of inversion, making sure that Main Frame does not
strike Front Frame at any time during use, as shown in illustrations on page 12.
Do not allow children to use or play on the Inversion Stretch System.

11.
Keep small children and pets away from the Inversion Stretch System at all times.

12.
The Inversion Stretch System should not be used by persons weighing more than 250 lbs.

13.
The Inversion Stretch System should not be used by persons over 6 feet 6 inches tall.

14.
It is recommended that you place this exercise equipment on an equipment mat.

15.
Use the Inversion Stretch System only on a level surface.

16.
Wear appropriate clothing when exercising; do not wear loose clothing that could become caught in the Inversion Stretch System.

17.
Be sure that there is enough room for the bed to rotate completely.

18.
Use the Inversion Stretch System only as described in the manual.

19.
The safety level of the Inversion Stretch System can be maintained only if it is examined regularly for damage and wear.

20.
This equipment is for home use only. It is not for commercial use.

21.

This product contains a chemical known to the State of California to cause cancer and
birth defects or other reproductive harm.
To reduce the risk of serious injury, read the following Safety Instructions before using
the Inversion Stretch System.

!

WARNING

especially important if you are over the age of 35, have never exercised before, are pregnant, or suffer
from any health problem. This product is for home use only. Do not use in institutional or commercial
applications. Failure to follow all warnings and instructions could result in serious injury or death. Do
not use this equipment if you have any of the following conditions or ailments:

Extreme obesity
Glaucoma, retinal detachment or conjunctivitis
Pregnancy
Spinal injury, Cerebral Sclerosis, or acutely swollen joints
Middle ear infection
High blood pressure, hypertension, recent stroke or transient ischemic attack
Heart or circulatory disorders for which you are being treated
Hiatus hernia or ventral hernia
Bone weaknesses including osteoporosis, unhealed fractures, medullary pins, or surgically
implanted orthopedic supports.

Use of anti-coagulants including aspirin in high doses.

Consult your physician before starting this or any exercise program. This i s

2

Call Us First

www.staminaproducts.com

Customer Service

1 [phone]

THANK YOU FOR PURCHASING THE

Inversion Stretch System

To enact your warranty, please register your product

by going to register.staminaproducts.com

To help you get started, we have pre-assembled most of your

Inversion Stretch System at the factory with the exception

of those few parts left unassembled for shipping purposes.

Simply follow the few assembly instructions set forth in this manual.

With regular workouts, you will be getting your body into shape

and be on your way to achieving a happier and healthier lifestyle.

Should you have any questions,

please call our Customer Service Department toll-free number,

1 [phone]

Monday - Thursday, 7:30 A.M. - 5:00 P.M., Central Time.

Friday, 8:00 A.M. - 3:00 P.M., Central Time.

ONLINE

CUSTOMER SERVICE

[e-mail]

www.staminaproducts.com

TELEPHONE

CUSTOMER SERVICE

Tel: [phone]

3

FAX

CUSTOMER SERVICE

Fax: [phone]

MAIL

STAMINA PRODUCTS, INC.

ATTN: Customer Service

P.O. Box 1071

Springeld, MO. 65801-1071

BEFORE YOU BEGIN

Thank you for choosing the Inversion Stretch

System. We take great pride in producing this

quality product and hope it will provide many hours
of quality exercise to make you feel better, look
better, and enjoy life to its fullest.

It's a proven fact that a regular exercise program
can improve your physical and mental health.
Too often, our busy lifestyles limit our time and
opportunity to exercise. The Inversion Stretch
System provides a convenient and simple method
to begin your assault on getting your body in shape
and achieving a happier and healthier lifestyle.

Befo r e read i ng fur t her, plea s e revie w the
drawing below and familiarize yourself with the
parts that are labeled.

Read this manual carefully before using the

Inversion Stretch System.

Although Stamina constructs its products with

the nest materials and uses the highest standards

of manufacturing and quality control, there can
sometimes be missing parts or incorrectly sized
parts. If you have any questions or problems with
the parts included with your Inversion Stretch
System, please do not return the product. Contact
us FIRST!

If a part is missing or defective, please go to
staminaproducts.com to the Services section and
order the part needed, or call us toll free at 1-800­375-7520 (in the U.S.). Our Customer Service Staff
is available to assist you from 7:30 A.M. to 5:00 P.M.
(Central Time) Monday through Thursday and 8:00
A.M. to 3:00 P.M. (Central Time) on Friday.

Be sure to have the name and model number of
the product available when you contact us.

Hand Grip

Inversion

Warning Decal

Height

Adjustment Beam

Front Frame

Foam Pad

Lever

Footrest

Heel Holder

Main Frame

Nylon Bed

Hand Grip

Protective Cover

Rear Frame

Buckle Strap

Warning Label

Bumper

THE FOLLOWING TOOLS ARE REQUIRED FOR ASSEMBLY : Phillips Screwdriver

Adjustable Wrench

4

EQUIPMENT WARNING, CAUTION & NOTICE LABELS

This chart is provided to help identify the warning, caution, and notice labels on the Inversion
Stretch System. Please take a moment to familiarize yourself with all of the warning, caution, and

notice labels.

Labels are larger than actual size

WARNING LABEL(44)W1

WARNING DECAL(45)W2

INVERSION WARNING DECAL(46)W3

ATTACH THE INVERSION WARNING DECAL TO THE MAIN FRAME AT

THE LOCATION SHOWN.

5

HARDWARE IDENTIFICATION CHART

This chart is provided to help identify the hardware used in the assembly process. Place the washers or
the ends of the bolts or screws on the circles to check for the correct diameter. Use the small scale to
check the length of the bolts and screws.

3/16" 1/4" 5/16" 3/8" 1/2"

INCHES

0 1/2 1 1/2 2 1/2 3 1/2 4 1/2 5 1/2 6

0 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150

MILLIMETERS

6 8 10 12

NOTICE: The length of all bolts and screws, except those with flat

heads, is measured from below the head to the end of the bolt
or screw. Flat head bolts and screws are measured from the
top of the head to the end of the bolt or screw.

After unpacking the unit, open the hardware bag and make sure that you have all the following items.
Some hardware may be already attached to the part.

length

length

in.

mm.

Part No. and Description Qty

32 Bolt, Hex Head (M6 x 1 x 42mm) 1
33 Bolt, Hex Head (M6 x 1 x 48mm) 1

35 Bolt, Hex Head (M8 x 1.25 x 50mm) 2

36 Nylock Nut (M6 x 1) 2
37 Nylock Nut (M8 x 1.25) 2

38 Washer (M6) 4
39 Washer (M8) 4

40 Large Washer (M6) 2

41 Bolt, Button Head (M6 x 1 x 8mm) 2

6

ASSEMBLY INSTRUCTIONS

Place all parts from the box in a cleared area and position them on the oor in front of you. Remove

all packing materials from your area and place them back into the box. Do not dispose of the packing
materials until assembly is completed. Read each step carefully before beginning. If you are missing
a part, please go to staminaproducts.com to the Services section and order the part needed, e-mail
us at [e-mail], or call us toll free at 1-800-375-7520 (in the U.S.). Our
Customer Service Staff is available to assist you from 7:30 A.M. to 5:00 P.M. (Central Time) Monday
through Thursday and 8:00 A.M. to 3:00 P.M. (Central Time) on Friday.

STEP 1

Unfold the BASE ASSEMBLY to an upright position by moving the FRONT FRAME(1) away from the
REAR FRAME(2). Then push down on the middle of the two FOLDING LINKAGES(3) until they are fully

locked down.

STEP 2

Slide one PROTECTIVE COVER(20) onto each side of the BASE ASSEMBLY, and pull the covers down
until the bottom of the covers are slightly lower than the FOLDING LINKAGES(3). Secure the PROTECTIVE

COVERS(20) to the FOLDING LINKAGES(3) with the SECURING STRAPS on the bottom of the covers.
NOTE: When the PROTECTIVE COVERS(20) are assembled correctly, the FOLDING LINKAGES(3)

should not be visible. Refer to the illustration.

7

ASSEMBLY INSTRUCTIONS

STEP 3

Slide the bottom of the two PIVOT ARMS(5) into the brackets located at each side of the MAIN FRAME(4).
Align the desired hole on the arm with the peg on the bracket, and insert the peg into the hole to lock
the PIVOT ARMS(5) in position. Then secure the PIVOT ARMS(5) on the pegs with BUTTON HEAD

BOLTS(M6x1x8mm)(41) and LARGE WASHERS(M6)(40).

PIVOT ARM ADJUSTMENT:

There are three adjustment holes on the PIVOT ARMS(5) allowing you to position the MAIN FRAME(4)
at three different heights. The lowest hole will allow the least amount of inversion angle. The top hole will
allow the greatest amount of inversion angle.

1.

CAUTION:

STEP 4

Attach the MAIN FRAME(4) onto the REAR FRAME(2) by sliding the slots in the ends of the two PIVOT
ARMS(5) into the slots on the REAR FRAME(2).

Use the lowest holes in the PIVOT ARMS(5) until you become familiar with the Inversion
Stretch System.

2.

Both PIVOT ARMS(5) must be adjusted to the same hole. Trying to adjust the PIVOT

ARMS(5) to different positions could cause damage to the machine, and injury to the user.

SLOTS

8

ASSEMBLY INSTRUCTIONS

STEP 5

Attach the FOOTREST(7) onto the HEIGHT ADJUSTMENT BEAM(6) with BOLTS(M8x1.25x50mm)(35),
WASHERS(M8)(39), and NYLOCK NUTS(M8x1.25)(37).
NOTE:

STEP 6

Insert the OUTER PAD TUBE(9) through the hole on the HEIGHT ADJUSTMENT BEAM(6). Insert the
INNER PAD TUBE(8) into the OUTER PAD TUBE(9). Align the holes on the INNER PAD TUBE(8), OUTER
PAD TUBE(9), and HEIGHT ADJUSTMENT BEAM(6), then bolt them together with BOLT(M6x1x42mm)
(32), WASHERS(M6)(38), and NYLOCK NUT(M6)(36).

WARNING:

STEP 7

Insert the HEEL HOLDER TUBE(11) through the hole on the HEIGHT ADJUSTMENT BEAM(6) and
secure with BOLT(M6x1x48mm)(33), WASHERS(M6)(38), and NYLOCK NUT(M6x1)(36). Place a HEEL
HOLDER BRACKET(12) onto a HEEL HOLDER(13), then slide them onto HEEL HOLDER TUBE(11)
together. Repeat on other side.

The ve holes in the FOOTREST(7) allow the FOOTREST(7) to be attached in three different
positions. Start with the center position and adjust if necessary. Use the outer position if users are
taller than average. Use the inner position if users are shorter than average.

The PAD TUBES(8, 9) must be assembled with the ends pointed downward as shown. The ends
must be pointed downward to properly secure the users feet in place during inversion. Improper
assembly will allow the user's feet to come loose and the user will fall from the inversion table.

9

ASSEMBLY INSTRUCTIONS

STEP 8: Install the HEIGHT ADJUSTMENT BEAM(6) into MAIN FRAME(4) by pulling the LARGE SPRING

PIN(16) on the MAIN FRAME(4) and inserting the HEIGHT ADJUSTMENT BEAM(6) as shown. For added
safety, thread the LOCKING KNOB(17) into back side of the MAIN FRAME(4).

WARNING: Do not use the Inversion Stretch System until you have veried your height setting. Failure

to use the proper height setting can result in difculty recovering from the decline position. See

HEIGHT ADJUSTMENT instructions on page 11.

1. 2.

BUCKLE

A.

BUCKLE

B.

C.

3.

STEP 9:

attach the end of the BUCKLE STRAP(25) to the hook on the FRONT FRAME(1), as shown in
Illustration 2. The NYLON STRAP(24) must be secured to the MAIN FRAME(4) and the BUCKLE
STRAP(25) must be secured to the FRONT FRAME(1).

STEP 10:

NYLON STRAP(24) through the bottom of the BUCKLE, as shown in Illustration 3 (Steps A, B and C).
The NYLON STRAP(24) must be securely attached to the BUCKLE STRAP(25) through the BUCKLE.

The NYLON STRAP(24) and BUCKLE STRAP(25) are used to control the decline angle of the MAIN
FRAME(4). Check the decline angle before using the Inversion Stretch System. To increase the
decline, lengthen the straps. To decrease the decline, shorten the straps.

WARNING: DO NOT ALLOW table to invert past vertical. Table inverting past vertical may result in table

Attach the end of the NYLON STRAP(24) to the hook on the back of the MAIN FRAME(4);

Attach the NYLON STRAP(24) to the BUCKLE STRAP(25) by inserting the end of the

contacting frame, damage to table and serious injury to user due to fall hazard. Prior to each
use, make sure nylon and buckle straps are securely attached, as instructed in Steps 9 and

10. Adjust straps to desired angle of inversion, making sure that Main Frame does not strike
Front Frame at any time during use, as shown in illustrations on page 12.

10

OPERATIONAL INSTRUCTIONS

GENERAL PRECAUTIONS

Use the lowest holes in the PIVOT ARMS(5) until you become familiar with the Inversion Stretch System.

1.
Do not use the Inversion Stretch System alone. Always have a helper available in case assistance is

2.
needed in recovering from the decline position.
Make sure that the FOAM PADS(10) and HEEL HOLDERS(13) are holding your feet securely.

3.
Make sure that the HEIGHT ADJUSTMENT BEAM(6) is properly set for your height.

4.
Make sure that the HEIGHT ADJUSTMENT BEAM(6) is held securely by both the SPRING PIN(16)

5.
and the SECURING KNOB(17).
Make sure that there is enough room for the bed to rotate completely.

6.

HEIGHT ADJUSTMENT

The Inversion Stretch System is a very sensitive balance device. It responds to very slight changes in
weight distribution. It is very important to make sure that the height adjustment is adjusted properly. Use
the following procedure to set the height adjustment and balance the Inversion Stretch System.

Adjust the NYLON STRAPS to restrict movement

1.
to approximately 15 deg rees beyond the
horizontal position. The nylon straps should not
allow the Inversion Stretch System to go into
the full inversion position while you are setting
the height adjustment.
Loosen the LOCKING KNOB(17) under the MAIN

2.

FRAME(4).

Pull the SPRING PIN(16) and use the SCALE

3.

DECAL(14) to set the HEIGHT ADJUSTMENT
BEAM(6).

Tighten the LOCKING KNOB(17).

4.
Mount the machine.

5.
Lock your ankles into the FOAM PADS(10) and

6.

HEEL HOLDERS(13).

Lie back with your hands at your sides.

7.
Slowly raise your hands to your chest.

8.
If your feet are higher than your head, dismount

9.
and try a taller setting. If you do not rotate to a
position close to level, dismount and try a shorter
setting.

1.

NOTE:

The Inversion Stretch System should return to the upright position when your hands are below
your waist. If it does not, use a taller setting.

2.

Verify that adequate head clearance is available between the user's head and the oor before

using this inversion table. This is especially important for tall users.

THE HANDLEBARS

For added convenience, and safety, a set of HANDLEBARS has been added to the Inversion Stretch
System. These HANDLEBARS are located at the top of the REAR FRAME(2). The HANDLEBARS are

to help you return to the upright position from any degree of inversion. If you wish to return to the upright
position, and the bed is moving too slowly, or not moving at all, simply grab the HANDLEBARS and pull
on them until you return to the upright position.

11

OPERATIONAL INSTRUCTIONS

HEEL HOLDER USE AND ADJUSTMENT

Place your feet on the FOOTREST(7) with your ankles between the

1.

Button

HEEL HOLDERS(13) and FOAM PADS(10).

The HEIGHT ADJUSTMENT BEAM(6) includes a lever to grip and

2.
release your feet. Pull the lever toward you until your ankles are securely
held between the HEEL HOLDERS(13) and FOAM PADS(10).

To release your feet or relax the grip, pull the lever toward you slightly

3.
and press the button on the end of the lever.

USING THE INVERSION TABLE

1. Check the decline angle before using the Inversion Stretch System. To increase the decline,
lengthen the straps. To decrease the decline, shorten the straps.

WARNING: DO NOT ALLOW table to invert past vertical. Table inverting past vertical may result in table

contacting frame, damage to table and serious injury to user due to fall hazard. Prior to each
use, make sure nylon and buckle straps are securely attached, as instructed in Steps 9 and

10. Adjust straps to desired angle of inversion, making sure that Main Frame does not strike
Front Frame at any time during use, as shown in illustration below.

Gap

NOTE: There must

always be a gap
between the Main
Frame and the Front
Frame when in use.

Not Past Vertical Past Vertical

12

OPERATIONAL INSTRUCTIONS

USING THE INVERSION TABLE

Start by lying fully back on the bed with your hands at your side, or resting on your thighs.

2.
Keeping your hands close to your body begin to raise your arms slowly allowing the table to rotate

3.
backward. Stop, or lower your arms to control the downward rotation of the table.
Raise your arms until they are over your head. At this point, the inversion table will be as far back as

4.
it can go.
As you get more comfortable with the use, rock the bed slowly by moving your arms up and down slowly.

5.

It is recommended that the inversion table be used for ve or ten minutes each morning, and again

6.
each evening.
Return to the upright position by slowly moving your hands back down to your thighs.

7.

3.1.

4.2.

SUGGESTIONS FOR USE

Begin slowly: Invert only 15-20 degrees to begin with. Stay inverted only as long as you are comfortable.

1.
Return upright slowly.
Make gradual changes: Increase the angle only if it is comfortable. Increase the angle only a few degrees

2.
at a time. Increase the time of use 1-2 minutes up to ten over a period of weeks. Add stretching and
light exercise only after you are comfortable with inversion.
Watch your body: Come up slowly, dizziness after a session means you came up to fast. Wait a while

3.

after eating before using table. If you get nauseous, do not ght it, come up as soon as you feel queasy.

Keep moving: Movement may be accomplished by either rhythmic traction or light exercise. Do not

4.
exercise strenuously while inverted. Limit partial inversion without movement to one or two minutes.
Limit full inversion with no movement to only a few seconds.
Invert regularly: We recommend two or three times a day depending upon your current condition. Try

5.
to schedule your inversion sessions for the same times each day.

13

STORAGE

FOLDING THE INVERSION TABLE

The Inversion Stretch System can be easily folded for storage.

To fold the Inversion Stretch System loosen LOCKING KNOB(17) and pull out the SPRING PIN(16).
Now, slide the HEIGHT ADJUSTMENT BEAM(6) all the way up into the MAIN FRAME(4) until the HEEL

HOLDERS(13) are just below the MAIN FRAME(4), release the SPRING PIN(16) and slide the HEIGHT
ADJUSTMENT BEAM(6) slightly up or down until the spring pin locks the beam in place. Remove the
MAIN FRAME ASSEMBLY from the BASE by lifting up on the MAIN FRAME(4) until the PIVOT ARMS(5)

come out of the slots located at the top of the REAR FRAME(2), (Make sure the NYLON STRAP is not
attached to the MAIN FRAME(4) before attempting to remove it.) Push up on the center of the FOLDING
LINKAGES(3) and push the FRONT FRAME(1) and REAR FRAME(2) together until they meet.

MAINTENANCE

The safety level of the Inversion Stretch System can be maintained only if it is examined regularly for
damage and wear.

Check the nylon strap, strap buckle, pivot arms, nylon bed, heel holders, foam pads, and spring pin for

1.
damage and wear.
Replace damaged and worn components immediately and/or keep the equipment out of use until repairs

2.
are complete.

14

LIMITED WARRANTY

WARRANTY

Stamina Products, Inc. warrants that this product will be free from defects in materials and workmanship

under normal use, service and proper operation for a period of 90 days on the parts and ve years on

the frame from the date of the original purchase from an authorized retailer. THIS WARRANTY SHALL
NOT APPLY TO ANY PRODUCT WHICH HAS BEEN SUBJECT TO COMMERCIAL USE, ABUSE,
MISUSE, ALTERATION OF ANY TYPE OR CAUSE OR TO ANY DEFECT OR DAMAGE CAUSED BY
REPAIR, REPLACEMENT, SUBSTITUTION OR USE WITH PARTS OTHER THAN PARTS PROVIDED
BY STAMINA PRODUCTS, INC. Commercial use includes use of the product in athletic clubs, health

clubs, spas, gymnasiums, exercise facilities, and other public or semipublic facilities whether or not the

product's use is in furtherance of a prot making enterprise, and all other use which is not for personal,

family, or household purposes.

To implement this limited warranty, send a written notice stating your name, date, and place of purchase
and a brief description of the defect along with your receipt to Stamina Products, Inc. P.O. Box 1071,
Springeld Missouri, USA, 65801-1071, or email us at [e-mail], or
call us at 1-800-375-7520. If the defect is covered under this limited warranty, you will be requested to
return the product or part to us for free repair or replacement at our option. NO ACTION FOR BREACH

OF THIS LIMITED WARRANTY MAY BE COMMENCED MORE THAN ONE (1) YEAR AFTER THE
DATE THE ALLEGED BREACH WAS OR SHOULD HAVE BEEN DISCOVERED. NO ACTION FOR
BREACH OF ANY IMPLIED WARRANTY MAY BE COMMENCED MORE THAN ONE (1) YEAR AFTER
DELIVERY OF THE PRODUCT TO THE PURCHASER. This limited warranty is not transferable. IF
ANY PART OF THE PRODUCT IS NOT IN COMPLIANCE WITH THIS LIMITED WARRANTY OR ANY
IMPLIED WARRANTY, THE REMEDY OF REPAIR OR REPLACEMENT IS THE EXCLUSIVE REMEDY
AVAILABLE TO YOU. In the event that the purchaser makes any claim under this limited warranty or any

implied warranty, the Warrantor reserves the right to require the product to be returned for inspection,

at the purchaser's expense, to the Warrantor's premises in Springeld, Missouri. Return of the enclosed

warranty registration card is not required for warranty coverage, but is merely a way of establishing the
date and place of purchase.

Stamina Products, Inc. SHALL NOT BE LIABLE FOR THE LOSS OF USE OF ANY PRODUCT, LOSS

OF TIME, INCONVENIENCE, COMMERCIAL LOSS OR ANY OTHER INDIRECT, CONSEQUENTIAL,
SPECIAL OR INCIDENTAL DAMAGES DUE TO BREACH OF THE ABOVE WARRANTY OR ANY
IMPLIED WARRANTY.

This limited warranty is the only written or express warranty given by Stamina Products, Inc. This

warranty gives you specic legal rights, and you may also have other legal rights which vary from state

to state. ANY OTHER RIGHT WHICH YOU MAY HAVE, INCLUDING ANY IMPLIED WARRANTY OR
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, IS LIMITED IN DURATION TO
THE DURATION OF THIS WARRANTY.

The laws in some jurisdictions restrict the rights of manufacturers and distributors of consumer goods
to disclaim or limit implied warranties and consequential and incidental damages with respect thereto.
If any such law is found to be applicable, the foregoing disclaimers and limitations of and on implied
warranties and consequential and incidental damages with respect thereto shall be disregarded and shall
be deemed not to have been made to the extent necessary to comply with such legal restriction.

15

PRODUCT PARTS DRAWING

BACK

FRONT

16

PARTS LIST

PART# PART NAME QTY

1 Front Frame 1
2 Rear Frame 1
3 Folding Linkage 2
4 Main Frame 1
5 Pivot Arm 2
6 Height Adjustment Beam 1
7 Footrest 1
8 Inner Pad Tube 1
9 Outer Pad Tube 1
10 Foam Pad 2
11 Heel Holder Tube 1
12 Heel Holder Bracket 2
13 Heel Holder 2
14 Scale Decal 1
15 Bushing 2
16 Spring Pin 1
17 Locking Knob 1
18 Foam Cushion 1
19 Nylon Bed 1
20 Protective Cover 2
21 Hand Grip 2
22 Bumper 1
23 Hook 2
24 Nylon Strap 1
25 Buckle Strap 1
26 Hollow Cap 1
27 Round Plug (7/8") 4
28 Square Plug (1 5/16" x 1 5/16") 1
29 Square Plug (1 1/2" x 1 1/2") 1
30 Oval Plug (20mm x 60mm) 2
31 Bolt, Round Head (M6 x 1 x 30mm) 4
32 Bolt, Hex Head (M6 x 1 x 42mm) 1
33 Bolt, Hex Head (M6 x 1 x 48mm) 1
34 Bolt, Hex Head (M8 x 1.25 x 23mm) 2
35 Bolt, Hex Head (M8 x 1.25 x 50mm) 2
36 Nylock Nut (M6 x 1) 6
37 Nylock Nut (M8 x 1.25) 4
38 Washer (M6) 12
39 Washer (M8) 8
40 Large Washer (M6) 2
41 Bolt, Button Head (M6 x 1 x 8mm) 2
42 Double sided Tape 1
43 Manual 1
44 Warning Label 1
45 Warning Decal 1
46 Inversion Warning Decal 1

17

TO CONTACT CUSTOMER SERVICE

TO CONTACT CUSTOMER SERVICE

For yo ur convenience, Stamina’s c ustomer serv ice representatives can be reached by email at customerservice@
staminaproducts.com or by phone at 1-800-375-7520 (in the U.S.). Our customer service representatives are available Monday
through Thursday from 7:30 a.m. until 5:00 p.m., and Friday 8:00 a.m. until 3 p.m. Central Time.

ONLINE

CUSTOMER SERVICE

[e-mail]

www.staminaproducts.com

TELEPHONE

CUSTOMER SERVICE

Tel: [phone]

FAX

CUSTOMER SERVICE

Fax: [phone]

STAMINA PRODUCTS, INC.

P.O. Box 1071 Springeld, MO. 65801-1071

MAIL

ATTN: Customer Service

Would you like to recieve email information or special offers from Stamina Products? Register at contact.staminaproducts.com

TO REGISTER YOUR PRODUCT

TO REGISTER YOUR PRODUCT

To enact your warranty, please register your product by going to register.staminaproducts.com. Please have your product model
number (printed on the cover of this owner’s manual) and the serial number (printed on the black and white sticker on your
product) ready.

If you don’t have internet access, you can call customer service at 1-800-375-7520, or ll out and mail the product registration
form below to Stamina Products, Inc.; P.O. Box 1071; Springeld, MO 65801-1071.

PRODUCT REGISTRATION FORM

Model Number: ...................................................................................... Serial Number: .............................................................................................

Product Name: ..................................................................................................................................................................................................................................

Place Purchased: ..............................................................................................................................................................................................................................

Date of Purchase: .................................................................................. Purchase Price: ............................................................................................

First Name: ............................................................................................ Last Name: ...................................................................................................

City: .................................................................. State: ................................................................ Zip Code: .................................................

Email Address: ....................................................................................... Phone #: ( ) ......................................................................................

Would you like to receive email information or special offers from Stamina Products?* ____Yes ____No

Stamina Products, Inc.

P.O. Box 1071

Springeld, MO 65801-1071

*If yes, be sure your email address is included above.

Detach and Mail or Fax the Form Above

TO ORDER PARTS

TO ORDER PARTS

If there are missing or damaged parts, you can go to parts.staminaproducts.com and order those parts. If you have questions,
please contact customer service. Do not return the product. To order parts by mail, fill out the sheet below and fax it to
417-889-8064. The part will be mailed to your address.

Detach and Mail or Fax the Form Below

PARTS ORDER FORM

Mr./Ms: ..............................................................................................................................................................................................................................................

Address: ........................................ ............................................................................................. Apt. #:..........................................................................

City: .................................................................. State: ................................................................ Zip Code: .................................................

IMPORTANT : We must have your phone number to process the order!

Phone #: ( ) ................................................................................ Work Phone #: ( ) .............................................................................

Date of Purchase: ..................................................................................

Model #: ............................................................................................................................................................................................................................................

Purchased From: ..............................................................................................................................................................................................................................

IMPORTANT : Before lling out the form below make sure you have the correct information.

PART # DESCRIPTION QUANTITY

EXAMPLE:

1 Rear Unit Assembly 1

Refer to the parts list to make sure you're ordering the right parts!

Stamina Products, Inc.

P.O. Box 1071

Springeld, MO 65801-1071