Stamina 1350 User Manual

Owner's

Manual

W A RNING

Exercise can pre sent a health
risk. Consult a physician
before beginning a ny exercise
program with this equipment.
If you feel faint or dizzy,
immediately discontinue use
of this equipment. Serious
bodily injury can occur if this
equipment is not assembled
and used correctly. Serious
bodily injury can also occur if
all instructions are not
followed. Keep others and
pets away from equipment
when in use. Always make
sure all bolts and nuts are
tightened prior to each use.
Follow all safety instructions in
this manual.
When calling for parts or
service, please specify the
following number.

CAUTION:
Weight on this product should not exceed 250 lbs.

This Product is Produced Exclusively by

2040 N. Alliance, Springfield, MO 65803

Customer Service

1 [phone]

2008, 07

www.stamin aproducts.com

Model#: 15-1350

STAMINA PRODUCTS

MADE IN CHINA

Product May Vary Slightly

From Pictured.

2008 Stamina Products, Inc.

TABLE OF CONTENTS

Page Page

Safety Instructions 2
Before You Begin 4
Equipment Warning & Notice Labels 5
Hardware Identification Chart 6
Assembly Instructions 7
Set Up Instructions 11
Operational In structions 12
Storage 14

Maintenance 14
Conditioning Guidelines 15
Warm-Up and Cool-Down 16
Warra nty 17
Product Parts Drawing 18
Parts List 19
Notes 21
Fax/Mail Ordering Form 22

SAFETY INSTRUCTIONS

WARNING:

Read all warnings posted on the Magnetic Recumbent 1350 Bike.

1.
The Magnetic Recumbent 1350 Bike should only be used after a thorough review of the Owner's Manual.

2.
We recommend that two people be available for assembly of this product.

3.
Keep children away from the Magnetic Recumbent 1350 Bike. Do not allow children to use or play on the

4.
Magnetic Recumbent 1350 Bike. Keep children and pets away from the Magnetic Recumbent 1350 Bike
when it is in use.
The M agnetic Recumbent 1350 Bike is not a freewheeling exercise bike; theref ore, pedal speed should be

5.
reduced in a controlled manner to prevent injury from spinning pedals.
Make sure that the Magnetic Recumbent 1350 Bike is properly assembled and tightened before use.

6.
It is recommended that you place this exercise equipment on an equipment mat.

7.
Set up and operate the Magnetic Re cumbent 1350 Bike on a solid level surface. Do not position the Magnetic

8.
Recumbent 1350 Bike on loose rugs or uneven surfaces.
Make sure that adequate space is available for access to and around the Magnetic Recumbent 1350 Bike.

9.
Adjust the LEVELING CAPS on the REAR STABILIZER so that the Magnetic Recumbent 1350 Bike sits on

10.
the floor without rocking.
Before using, inspect the Magnetic Recumbent 1350 Bike for worn or loose components, and tighten or

11.
replace any loose or worn components prior to use.
The ADJUSTMENT KNOB(37) should be securely tightened prior to use.

12.
Each user should adjust the seat per instructions on page 12.

13.
Before using, always check the seat post to be sure it is secure. The a djustment knob must be inserted into

14.
one of the holes in the seat post and tightened.
Consult a physician prior to commencing an exercise program. If, at any time during exercise, you feel faint,

15.
dizzy, or experience pain, stop and consult your physician.
Follow your physician's recommendations in developing your own personal fitness program.

16.
Always choose the workout which best fits your physical strength and flexibility level. Know your limits and

17.
train within them. Always use common sense when exercising.
Do not wear loose or dangling clothing while using the Magnetic Recumbent 1350 Bike.

18.
Never exercise in bare feet or socks; always wear proper footwear such as running, walking, or cross

19.
training shoes that fit well, provide foot support, and feature non-skid rubber soles.
Care should be taken in mounting or dismounting the Magnetic Recumbent 1350 Bike.

20.
The Magnetic Recumbent 1350 Bike should not be used by persons weighing over 250 pounds.

21.
The Magnetic Recumbent 1350 Bike should be used by only one person at a time.

22.
The M agnetic Recumbent 1350 Bike is for con sumer use only . It is not for use in public or semi public facilitie s.

23.
Use two people to move the Magnetic Recumbent 1350 Bike.

24.

To reduce the risk of serious injury, read the following Safety Instructions before
using the Magnetic Recumbent 1350 Bike.

WARNING:

Before starting any exercise or conditioning program you should consult with your personal
physicia n to see if you require a complete physical exa m. This is especially i mporta nt if you
are over the age of 35, have never exercised before, are pregnant, or suffer from any
illness. READ AND FOLLOW THE SAFETY PRECAUTIONS. FAILURE TO FOLLOW

THESE INSTRUCTIONS CAN RESUL T IN SERIOUS BODILY INJURY.

2

CALL US FIRST

Customer Service

1(800) 375-7520

www.staminaproducts.com

THANK YOU FOR PURCHASING THE

Magnetic Recumbent 1350 Bike

To help you get started, we have pre-assembled most of your

Magnetic Recumbent 1350 Bike at the factory with the exception

of those few parts left unassembled for shipping purposes.

Simply follow the few assembly instructions set forth in this manual.

With regular workouts, you will be getting your body into shape

and be on your way to achieving a ha ppier and healthier lifestyle.

Should you have any questions,

please call our Customer Service Department toll-free number,

1 [phone]

Monday - Thursday, 7:30 A.M. - 5:00 P.M., Central Time.

Friday, 8:00 A.M. - 3:00 P.M., Central Time.

TELEPHONE

CUSTOMER SERVICE

Tel: [phone]

FAX

CUSTOMER SERVICE

Fax: [phone]

ONLINE

CUSTOMER SERVICE

[e-mail]

www.staminaproducts.com

STAMINA PRODUCTS, INC.

ATTN: Customer Service

Springfield, MO. 65801-1071

MAIL

P.O. Box 1071

3

BEFORE YOU BEGIN

Thank you f or choosing the Magnetic Re cumbent
1350 Bike. We take great pride in producing this

quality product and hope it will provide many hours
of quality exercise to make you feel better , look better,
and enjoy life to its fullest.
It's a proven fact that a regular exercise program
can improve your physical and mental health. Too
often, our busy lifestyles limit our ti me and opportunity
to exercise. The Magnetic Recumbent 1350 Bike
provides a convenient and simple method to begin
your assault on getting your body in shape and
achieving a happier and healthier lifestyle.
Before reading further, please review the drawing
below and familiarize yourself with the parts that are
labeled.
Read this manual carefully before using the

Magnetic Recumbent 1350 Bike.

Left Pedal

Although Stamina constructs its products with the
finest materials and uses the highest standards of
manufacturing and quality control, there can
sometimes be missing parts or incorrectly sized
parts. If you have any questions or problems with
the parts included with your Magnetic Recumbent
1350 Bike, plea se do not return the product. Contact
us FIRST!
If a part is missing or defective, please call us toll
free at 1-800-375-7520 (in the U.S.). Our Customer
Service Staff is available to a ssist you from 7:30 A.M.
to 5:00 P .M. (Central T ime) Monday through Thursday
and 8:00 A.M. to 3:00 P.M. (Central T i me) on Friday.
If you would like to contact us online, go to our
website at www.sta min aproducts.com a nd a ccess the
Customer Service section.
Be sure to have the na me and model number of the
product available when you conta ct us.

Meter

Back Cushion

Seat Frames

Rear Frame

Leveling Cap

Rear Stabilizer
Warning Label

Leveling Cap

Left Cover

Seat Cushion

Right Handrail

Tension
Knob

Right Cover
Crank

Front
Stabilizer

Endcap
Right Pedal

Front Frame

Adjustment Knob

Foam Grip

THE FOLLOWING TOOLS ARE INCLUDED FOR ASSEMBLY : Wrench

Allen Wrench (6mm)

4

EQUIPMENT WARNING & NOTICE LABELS

This chart is provided to help identify the warning & notice labels on the Magnetic Recumbent 1350 Bike.
Please take a moment to familiarize yourself with all of the warning & notice labels.

Label is larger than actual size

W1

WAR NING LABEL(71)

5

HARDWARE IDENTIFICATION CHART

This chart is provided to help identify the hardware used in the a ssembly process. Place the washers or the
ends of the bolts or screws on the circles to check for the corre ct diameter. Use the small scale to check the
length of the bolts and screws.

3/16" 5/16" 1/2"3/8"1/4"

INCHES

11/2021/2 31/2 41/2 51/2 61/2

0 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150

MILLIMETERS

6 8 10 12

NOTICE: The length of all bolts and screws, except those with flat heads,

is mea sured from below the hea d to the end of the bolt or screw .
Flat head bolts and screws are measured from the top of the
head to the end of the bolt or screw.

After unpacking the unit, open the hardware bag and make sure that you have all the following items.
Some hardware may be already attached to the part.

length

length

in.

mm.

Part No. and Description Qty

47 Carriage Bolt (M8 x 1.25 x 65mm) 4

48 Bolt, Button Head (M8 x 1.25 x 15mm) 1

49 Bolt, Button Head (M10 x 1.5 x 122mm) 2

50 Bolt, Hex Hea d (M6 x 1 x 37mm) 4

51 Bolt, Round Head (M6 x 1 x 35mm) 8

54 Screw, Round Head (M5 x 0.8 x 15mm) 4

55 Screw, Flat He ad (M5 x 0.8 x 10mm) 1

59 Nylock Nut (M10 x 1.5 x 9mm Thick) 2

60 Acorn Nut (M6 x 1) 4
61 Acorn Nut (M8 x 1.25) 4

64 Arc Washer (M6) 4
65 Arc Washer (M8) 5

66 Lock Washer (M6) 4
67 Lock Washer (M8) 5

69 Washer (M10) 2

6

ASSEMBLY INSTRUCTIONS

Place all parts from the box in a cleared area and position them on the floor in front of you. Remove all
packing materi als from your area a nd pla ce the m ba ck into the box. Do not dispose of the pa cking materi als
until a ssembly is completed. Read e a ch step carefully before beginning. If you are missing a part please call
our toll-free number for a ssistance 1-800-375-7520 or e-mail us at: customerservice@sta min aproducts.com

STEP 1

Attach the FRONT STABILIZER(2), the short one with the ENDCAPS(36), to the front of the FRONT
FRAME(1) with CARRIAGE BOLTS(M8x1.25x65mm)(47), ARC WASHERS(M8)(65), LOCK
WASHERS(M8)(67), a nd ACOR N NUTS(M8x1.25)(61).

STEP 2

Unscrew to re move the ADJUSTMENT KNOB(37) from the FRONT FRAME(1). Slide the REAR FRAME(3)
backward and secure with the ADJUSTMENT KNOB(37). Attach the REAR STABILIZER(4), the one with
the LEVELING CAPS(40), to the REAR FRAME(3) with CARRIAGE BOLTS(M8x1.25x65mm)(47), ARC

WASHERS(M8)(65), LOCK W ASHERS(M8)(67), a nd ACOR N NUTS(M8)(61).
NOTE:

You can adjust the LEVELING CAPS(40) on the REAR STABILIZER(4) to keep the Recumbent
Bike stable.

STEP 3

Attach the LEFT and RIGHT SEAT FRAMES(5, 6) to both sides of the REAR FRAME(3) with BUTTON
HEAD BOL TS(M10x1.5x122mm)(49), WASHERS(M10)(69), and NYLOCK NUTS(M10x1.5)(59).

7

ASSEMBLY INSTRUCTIONS

STEP 4

NOTE:

Attach the RIGHT HANDRAIL(8) to the RIGHT SEAT FRAME(6) with HEX BOLTS(M6x1x37mm)(50),
ARC WASHERS(M6)(64), LOCK WASHERS(M6)(66), and ACORN NUTS(M6x1)(60). Repeat on the left

side.

Install the HEX BOL TS
of the bolts to fit inside the hex shape holes in the SEAT FRAMES(5, 6).

(M6x1x37mm)(50) as shown in the illustration a bove. This allows the he ad

STEP 5

Attach the SEAT CUSHION(41) to the LEFT and RIGHT SEA T FRAMES(5, 6) with ROUND HEAD BOLTS
(M6x1x35mm)(51).
Attach the BACK CUSHION(42) to the LEFT a nd RIGHT SEA T FRAMES(5, 6) with ROUND HEAD BOL TS
(M6x1x35mm)(51).

8

ASSEMBLY INSTRUCTIONS

A. B.

Strap A

Strap B

Metal Fitting

Cable End

Bracket

Spring Hook

STEP 6

Refer to illustration A. Pull the ends of the TENSION CABLE(24) a nd SENSOR WIRE(28) out of the FRONT
FRAME(1). There are two stra ps attached in side of the METER POST(26) to a ssist when pulling the SENSOR
WIRE(28) and the TENSION CABLE(24) through the METER POST(26). Tie STRAP A to the plug end of

the SENSOR WIRE(28). Tie STRAP B to the BRACKET of the TENSION CABLE(24). Pull the STRAP A
from the square hole on the top of the METER POST(26) until the SENSOR WIRE(28) is pulled through and
extends out of the square hole. Pull the STRAP B from the square hole on the side of the METER POST(26)
until the TENSION CABLE(24) extends out of the side. Insert the METER POST(26) onto the FRONT

FRAME(1) and secure with BUTTON HEAD BOLT(M8x1.25x15mm)(48), LOCK WASHERS(M8)(67), and
ARC WASHERS(M8)(65).

STEP 7

Refer to illustration B and the inset drawing. Turn the TENSION K NOB(25) counterclockwise as far a s it ca n
go, so the CABLE END extends out of the metal fitting as far a s possible. Conne ct the CABLE END of the

TENSION KNOB(25) into the SPRING HOOK on the end of the TENSION CABLE(24). Pull on the CABLE
END of the TENSION KNOB(25) firmly so that enough cable is availa ble to insert the CABLE END through

the slot in the BRACKET. Then in sert the MET AL FITTING on the CABLE END of the TENSION KNOB(25)
into the hole at the end of the slot in the BRACKET. Adjust the TENSION KNOB(25) and verify that the

SPRING HOOK moves when the TENSION KNOB(25) is adjusted. Atta ch the TENSION KNOB(25) to the
METER POST(26) with FLA T HEAD SCREW(M5x0.8x10mm)(55).

9

ASSEMBLY INSTRUCTIONS

STEP 8

NOTE:

Thread the RIGHT PEDAL(35) to the right side of the CRANK(9) as shown. Tighten the pedal securely. Do
the same to attach the LEFT PEDAL(34) to the left side of the CRANK(9).

The RIGHT PEDAL(35) has R sta mped on the end of the pedal shaft. The RIGHT PEDAL(35) ha s
right hand threa ds and is tightened by turning clockwise. The LEFT PEDAL(34) ha s L stamped on
the end of the pedal shaft. The LEFT PEDAL(34) ha s left hand threads and is tightened by turning
counter clockwise.

STEP 9

Install two AA batteries into the METER(27), two batteries included. See page 13 f or detailed battery installation
instructions. Plug the SENSOR WIRE(28) into the METER(27), and push the excess wires back into the

METER POST(26). Place the METER(27) onto the plate on the METER POST(26) and secure with ROUND
HEAD SCREWS(M5x0.8x15mm)(54).
NOTE: Be careful not to da mage the wires when attaching the METER(27).

10

SET UP INSTRUCTIONS

Place the Magnetic Recumbent 1350 Bike in the area where it will be used. It is recommended that the
Magnetic Recumbent 1350 Bike be placed on an equipment mat. The Magnetic Recumbent 1350 Bike

is approximately 61 3/4 inches long (max.) x 27 1/2 inches wide x 36 inches tall. (These dimensions may
vary up to one inch.) An area 4 feet wide x 7 feet long is required for safe operation of the Magnetic

Recumbent 1350 Bike. Ma ke sure that a dequate space is available for access to and pa ssage around the
Magnetic Recumbent 1350 Bike.

LEVELING:

MOVING:

Adjust the LEVELING CAPS(40) on the REAR STABILIZER(4) so the bike sits on the floor
without rocking. Remove and re position the LEVELING CAPS(40) on the REAR STABILIZER
(4) to level the

The Magnetic Recumbent 1350 Bike must be lifted to be moved. T wo people are required to
grasp the FRONT STABILIZER(2) and the REAR STABILIZER(4), lift and move.

Magnetic Recumbent 1350 Bike.

EQUIPMENT MAT
Please note the Rear Frame of the
Recumbent Bike is adjustable. Use the
longest size to determine the size of the mat.

FUNCTION INSPECTION:

Visually inspect the Magnetic Recumbent 1350 Bike to verify that assembly is as shown in the above
illustration. Check the function of the Magnetic Recumbent 1350 Bike by turning the cra nk slowly through
one complete revolution to verify that the drive train functions properly . Adjust the TENSION K NOB(25) and
verify that it functions properly.

CAUTION:

Locate and read the WARNING LABEL(71) on the Magnetic Recumbent 1350 Bike. Make
sure that all users read the WARNING LABEL(71).

11

OPERATIONAL INSTRUCTIONS
SEAT ADJUSTMENT

Proper seat adjustment is important. There are seven adjustment holes in the REAR FRAME(3). These
adjustment holes allow users to adjust the position of the seat for efficient exercise.

Unscrew to re move the ADJUSTMENT KNOB(37) from the FRONT FRAME(1). Slide the REAR FRAME

1.

(3) to adjust the seat. Lock the REAR FRAME(3) in position by inserting the pin of the ADJUSTMENT
KNOB(37) into one of the adjustment holes in the REAR FRAME(3), then tighten the ADJUSTMENT
KNOB(37) to lock the REAR FRAME(3) securely.

Sit on the seat and place your feet on the pedals. You should be able to move through a complete pedal

2.
stroke without locking your knees or shifting your hips on the seat. The se at is too close to the pedals if
you have more than a slight bend in your knees at the bottom of the pedal stroke. The seat is too far from
the pedals if you have to completely straighten your knees at the bottom of the pedal stroke.

CAUTION:

1.

Do not attempt to adjust the seat while you are on the Magnetic Recumbent 1350 Bike.

2.

Always tighten the ADJUSTMENT KNOB(37) after adjusting the seat to a new position.

LOAD ADJUSTMENT

To increase the load, turn the TENSION KNOB(25) clockwise. To decrease the load, turn the TENSION
KNOB(25) counterclockwise.

12

OPERATIONAL INSTRUCTIONS
USING THE METER

POWER ON :

POWER OFF :

Pedal movement or push the button.
Automatic shut off after four minutes of

inactivity.

MODE/RESET BUTTON:

Press to select display functions, include SCAN, TIME,
SPEED, DIST ANCE, and CALORIES.

Press and hold for three seconds to reset all functions to
zero.

FUNCTIONS:

SCAN:

TIME:

Automatically scans each function of TIME, SPEED, DISTANCE, and CALORIES in
sequence with change every four seconds. Press and release the button until "SCAN"

appears on the display.
Displays the time from one second up to 99:59 minute s.

SPEED:

DISTANCE:

CALORIES:

NOTE:

Displays the current speed from zero to 999.9 miles per hour .
Displays the distance from zero to 99.99 miles.
Displays the calorie consumption from zero to 999.9 Kcal.

The calorie readout is an estimate for an average user. It should be used only as a
comparison between workouts on this unit.

The meter will shut off automatically after four minutes of in a ctivity . All function values will
be kept. Push the button and hold it down f or three seconds to reset all function s to zero.

HOW TO INSTALL AND REPLACE BATTERIES:

Open the Battery Door on the back of the meter.

1.
The meter operates with two AA batteries, two batteries included.

2.
Refer to the illustration to install or replace the batteries.

NOTE:

Do not mix a new battery with an old battery.

1.
Use the same type of battery. Do not mix an alkaline battery with

2.
another type of battery.
Rechargeable batterie s are not recommended.

3.

AA Batteries

13

STORAGE

1.

To store the Magnetic Recumbent 1350 Bike, simply keep it in a clean dry place.

2.

Adjust the REAR FRAME(3) into the FRONT FRAME(1) to the shortest position. The Magnetic
Recumbent 1350 Bike is approximately 39 3/4 inches long x 27 1/4 inches wide x 32 1/4 inches tall.
These dimension s will vary. Please measure your Magnetic Recumbent 1350 Bike if exact dimen sions
are needed.

3.

Use two people to lift the Magnetic Recumbent 1350 Bike

STABILIZER(4) to move.

4.

T o avoid da mage to the electronics, remove the batterie s before storing the Magnetic Re cumbent 1350
Bike for one year or more.

from the FRONT ST ABILIZER(2) and REAR

MAINTENANCE

The safety and integrity designed into the Magnetic Recumbent 1350 Bike can only be maintained when
the Magnetic Re cumbent 1350 Bike is regularly exa mined f or damage and wear. Spe cial attention should
be given to the following:

Adjust the TENSION KNOB(25) and verify that the Magnetic System provides tension. The Magnetic

1.
System should provide many years of use.
Use a wrench to verify that the pedals are tightened securely . If tightening is required, remember that the

2.
left pedal has left hand threads and is tightened by turning counterclockwise.
Verify that the W A RNING LABEL(71) is in pla ce a nd easy to read. Call Sta mina Products immedi ately at

3.
1-800-375-7520 for a replacement W A RNING LABEL(71) if it is missing or damaged.
It is the sole responsibility of the user/owner to ensure that regular maintenance is performed.

4.
Worn or damaged components shall be replaced immediately or the Magnetic Recumbent 1350 Bike

5.
removed from service until repair is made.
Only Sta mina Products supplied components shall be used to maintain/repair the Magnetic Recumbent

6.

1350 Bike.

Keep your Magnetic Recumbent 1350 Bike clean by wiping with an absorbent cloth after use.

7.

14

CONDITIONING GUIDELINES

How you begin your exercise program depends on your physical condition. If you have been inactive for
several years or are severely overweight, start slowly and increase your workout time gradually. Increase
your workout intensity gradually by monitoring your heart rate while you exercise.

Remember to follow these essentials:

Have your doctor review your training and diet programs.
Begin your training progra m slowly with realistic goals that have been set by you and your physician.
Warm up before you exercise and cool down after you work out.
Take your pulse periodically during your workout and strive to stay within a range of 60% (lower
intensity) to 90% (higher intensity) of your maximum heart rate zone. Start at the lower inten sity, and
build up to higher intensity as you become more aerobically fit.
If you feel dizzy or lightheaded you should slow down or stop exercising.

Initially you may only be able to exercise within your target zone for a few minutes; however, your a erobic
ca pa city will i mprove over the next six to eight week s. It is i mporta nt to pa ce yoursel f while you exercise so
you don't tire too quickly.

To determine if you are working out at the correct intensity, use a he art rate monitor or use the table below .
For effective aerobic exercise, your heart rate should be maintained at a level between 60% and 90% of
your maximum heart rate. If just starting an exercise progra m, work out at the low end of your target he art
rate zone. As your a erobic ca pa city improves, gra dually increa se the intensity of your workout by increa sing
your heart rate.

Measure your heart rate periodically during your workout by stopping the
exercise but continuing to move your legs or walk around. Place two or three
fingers on your wrist a nd take a six second heartbe at count. Multiply the results
by ten to find your heart rate. For exa mple, if your six se cond heartbeat count
is 14, your heart rate is 140 beats per minute. A six second count is used
because your heart rate will drop ra pidly when you stop exercising. Adjust the
intensity of your exercise until your heart rate is at the proper level.

Target Heart Rate Zone Estimated by Age*

Age

20 years
25 years
30 years
35 years
40 years
45 years
50 years
55 years
60 years
65 years
70 years

Target Heart Rate Zone

(55%-90% of Maximum Heart Rate)

110-180 beats per minute
107-175 beats per minute
105-171 beats per minute
102-166 beats per minute

99-162 beats per minute
97-157 beats per minute
94-153 beats per minute
91-148 beats per minute
88-144 beats per minute
85-139 beats per minute
83-135 beats per minute

Average Maximum

Heart Rate 100%
200 beats per minute
195 beats per minute
190 beats per minute
185 beats per minute
180 beats per minute
175 beats per minute
170 beats per minute
165 beats per minute
160 beats per minute
155 beats per minute
150 beats per minute

wrist pulse

For cardiorespiratory training benefits, the American College of Sports Medicine re commends working

*

out within a heart rate range of 55% to 90% of maximum heart rate. To predict the maximum heart
rate, the following formula was used: 220 - Age = predicted maximum heart rate

15

WARM-UP and COOL-DOWN

Warm-Up The purpose of warming up is to prepare your body f or exercise and to mini mize injuries. W arm

up for two to five minutes before strength training or aerobic exercising. Perform activities that raise your
heart rate a nd warm the working muscles. Activities may include brisk walking, jogging, jumping ja ck s, jump
rope, and running in place

Stretching Stretching while your muscles are warm after a proper warm-up and again after your strength

or aerobic training session is very important. Muscles stretch more easily at these times because of their
elevated temperature, which greatly reduces the ris k of injury . Stretches should be held for 15 to 30 seconds.
Do not bounce.

Suggested Stretching Exercises

Lower Body Stretch

Place feet shoulder-width
apart and lean forward.
Keep this position for 30
seconds using the body as a
natural weight to stretch the
backs of the legs.
DO NOT BOUNCE!
When the pull on the back of
the legs lessens, gradually
try a lower position.

Bent Torso Pulls

While sitting on the floor,
have legs apart, one leg
straight and one knee bent.
Pull the chest down to touch
the thigh on the leg that is
bent, and twist at the waist.
Hold this position at least 10
seconds. Repeat 10 times
on each side.

Floor Stretch

While sitting on the floor,
open the legs as wide as
possible. Stretch the upper
body toward the knee on the
right leg by using your arms
to pull your chest to your
thighs. Hold this stretch 10
to 30 seconds.
DO NOT BOUNCE!
Do this stretch 10 times.
Repeat the stretch with the
left leg.

Bent Over Leg Stretch

Stand with feet shoulder­width apart and lean forward
as illustrated. Using the
arms, gently pull the upper
body towards the right leg.
Let the head hang down.
DO NOT BOUNCE!
Hold the position a minimum
of 10 seconds. Repeat
pulling the upper body to the
left leg. Do this stretch
several times slowly.

Remember to always check with your physician before starting any exercise program.

Cool-Down The purpose of cooling down is to return the body to its normal, or near normal, resting state

at the end of each exercise session. A proper cool-down slowly lowers your heart rate and allows blood to
return to the heart. Your cool-down should include the stretches listed above and should be completed after
each strength training session.

16

LIMITED WARRANTY

MODEL 15-1350

WARRANTY

Stamina Products, Inc. warrants that this product will be free from defects in materials and workmanship
under normal use, service and proper operation for a period of 90 days on the parts and one year on the
frame from the date of the original purchase from an authorized retailer. THIS WARRANTY SHALL NOT

APPLY TO ANY PRODUCT WHICH HAS BEEN SUBJECT TO COMMERCIAL USE, ABUSE, MISUSE,
ALTERATION OF ANY TYPE OR CAUSE OR TO ANY DEFECT OR DAMAGE CAUSED BY REPAIR,
REPLACEMENT , SUBSTITUTION OR USE WITH PARTS OTHER THAN P ARTS PROVIDED BY ST AMINA
PRODUCTS, INC. Commercial use includes use of the product in athletic clubs, health clubs, spas,

gymnasiums, exercise facilitie s, and other public or semipublic facilities whether or not the product's use is
in furtherance of a profit making enterprise, and all other use which is not for personal, family, or household
purposes.

T o i mplement this li mited warranty, send a written notice stating your name, date, a nd pla ce of purcha se a nd
a brief description of the defect along with your rece ipt to Sta mina Products, Inc. P .O. Box 1071, Springf ield

Missouri, USA, 65801-1071, or email us at [e-mail], or call us at
1-800-375-7520. If the defect is covered under this limited warranty, you will be requested to return the
product or part to us for free repair or replacement at our option. NO ACTION FOR BREACH OF THIS
LIMITED WARRANTY MAY BE COMMENCED MORE THAN ONE (1) YEAR AFTER THE DATE THE
ALLEGED BREACH WAS OR SHOULD HAVE BEEN DISCOVERED. NO ACTION FOR BREACH OF
ANY IMPLIED W ARRANTY MAY BE COMMENCED MORE THAN ONE (1) YEAR AFTER DELIVERY OF
THE PRODUCT TO THE PURCHASER. This limited warranty is not transferable. IF ANY PART OF THE
PRODUCT IS NOT IN COMPLIANCE WITH THIS LIMITED W ARRANTY OR ANY IMPLIED W ARRANTY,
THE REMEDY OF REP AIR OR REPLACEMENT IS THE EXCLUSIVE REMEDY A V AILABLE T O YOU. In

the event that the purcha ser makes a ny claim under this limited warra nty or any i mplied warranty , the W arrantor
reserves the right to require the product to be returned for inspection, at the purchaser's expense, to the
Warra ntor's premises in Springfield, Missouri. Return of the enclosed warra nty registration card is not required
for warranty coverage, but is merely a way of establishing the date and place of purchase.

Sta mina Products, Inc. SHALL NOT BE LIABLE FOR THE LOSS OF USE OF ANY PRODUCT, LOSS OF

TIME, INCONVENIENCE, COMMERCIAL LOSS OR ANY OTHER INDIRECT, CONSEQUENTIAL,
SPECIAL OR INCIDENT AL DAMAGES DUE TO BREACH OF THE ABOVE WARRANTY OR ANY IMPLIED
WARRANTY.

This limited warra nty is the only written or expre ss warranty given by Stamina Products, Inc. This warranty
gives you specific legal rights, and you may also have other legal rights which vary from state to state.

ANY OTHER RIGHT WHICH YOU MAY HAVE, INCLUDING ANY IMPLIED WARRANTY OR
MERCHANT ABILITY OR FIT NESS FOR A P ARTICULAR PURPOSE, IS LIMITED IN DURA TION TO THE
DURA TION OF THIS WARRANTY.

The laws in some jurisdictions restrict the rights of manufacturers and distributors of consumer goods to
disclaim or limit implied warranties and consequential and incidental damages with respect thereto. If any
such law is found to be a pplicable, the foregoing disclai mers a nd limitations of a nd on implied warrantie s and
consequential a nd incidental da mages with respect thereto shall be disregarded a nd shall be deemed not to
have been made to the extent necessary to comply with such legal re striction.

17

PRODUCT PARTS DRAWING

FRONT

Strap A

Strap B

BACK

18

PARTS LIST

PART# PART NAME QTY

1 Front Frame 1
2 Front Stabilizer 1
3 Rear Frame 1
4 Rear Stabilizer 1
5 Left Seat Frame 1
6 Right Seat Frame 1
7 Left Handrail 1
8 Right Handrail 1
9 Crank 1
10 Bearing Housing 2
11 Ball Bearing 2
12 Inside Bearing Collar 1
13 Outside Bearing Collar 1
14 Bearing Washer 1
15 Bearing Snap Washer 1
16 Bearing Nut 2
17 Pulley 1
18 V-Ribbed Belt 1
19 Idler Arm 1
20 Idler Wheel 1
21 Idler Wheel Spacer 1
22 Tension Spring 1
23 Magnetic Unit 1
24 Tension Cable 1
25 Tension Knob 1
26 Meter Post 1
27 Meter 1
28 Sensor Wire 1
29 Magnet 1
30 Foa m Pad 3
31 Left Cover 1
32 Right Cover 1
33 Cover Cap 2
34 Left Pedal 1
35 Right Pedal 1
36 Endcap (50mm) 2
37 Adjustment Knob 1
38 Bushing 1
39 Inner Bushing 1
40 Leveling Cap (50mm) 2
41 Seat Cushion 1
42 Back Cushion 1
43 Foa m Grip 2
44 Round Plug (25.4mm) 2
45 Round Plug (50mm) 1
46 Square Plug (25.4mm x 25.4mm) 4
47 Carriage Bolt (M8 x 1.25 x 65mm) 4

19

PARTS LIST

PART# PART NAME QTY

48 Bolt, Button Head (M8 x 1.25 x 15mm) 1
49 Bolt, Button Head (M10 x 1.5 x 122mm) 2
50 Bolt, Hex Head (M6 x 1 x 37mm) 4
51 Bolt, Round Head (M6 x 1 x 35mm) 8
52 Bolt, Flat Head (M10 x 1.5 x 20mm) 1
53 Bolt, Flat Head (M10 x 1.5 x 35mm) 1
54 Screw , Round Head (M5 x 0.8 x 15mm) 4
55 Screw , Flat Head (M5 x 0.8 x 10mm) 1
56 Screw, Flat Head (M4 x 15mm) 2
57 Screw, Big Round Head (M5 x 15mm) 2
58 Screw, Round Head (M4 x 25mm) 5
59 Nylock Nut (M10 x 1.5 x 9mm thick) 4
60 Acorn Nut (M6 x 1) 4
61 Acorn Nut (M8 x 1.25) 4
62 Thin Nut (3/8" - 26 x 5/32" thick) 2
63 Nut (3/8" - 26 x 9/32" thick) 2
64 Arc Washer (M6) 4
65 Arc Washer (M8) 5
66 Lock Washer (M6) 4
67 Lock Washer (M8) 5
68 Large Washer (ø16.5 x ø32 x 0.5mm thick) 1
69 Washer (M10) 2
70 Screw , Round Head (M5 x 0.8 x 6mm) 1
71 Warning Label 1
72 Wrench 1
73 Allen Wrench (6mm) 1
74 Manual 1

20

NOTES

21

FAX/MAIL ORDERING FORM

Please do not return the product. For your convenience, Stamina's Customer Service Department can be
reached by email at [e-mail] or toll free at 1-800-375-7520 (in the U.S.).
Should a part be missing or a defective part found, please call us from 7:30 A.M. to 5:00 P.M. Central Ti me,
Monday through Thursday a nd 8:00 A.M. to 3:00 P.M. on Friday or fill out the fax sheet ordering form below
and fax it to [phone]. Our Customer Service Department will be able to assist you with your problem
and the part will be mailed directly to your house.

TELEPHONE

CUSTOMER SERVICE

Tel: [phone]

FAX

CUSTOMER SERVICE

Fax: [phone]

ONLINE

CUSTOMER SERVICE

[e-mail]

www.staminaproducts.com

STAMINA PRODUCTS, INC.

ATTN: Customer Service

Springfield, MO. 65801-1071

Detach and Mail or Fax the Form Below

Stamina Products, Inc.

P.O. Box 1071

Springfield, MO 65801-1071

Mr./Ms:
Address: Apt. #:
City: State: Zip Code:

IMPORTANT : We must have your phone number in order to process the order!

Phone #: ( ) Work Phone #: ( )
Date Purchased:
Model #:
Purchased From:

IMPORTANT : Before filling out the form below make sure you have the right information.

Refer to the parts list to make sure you're ordering the right parts!

MAIL

P.O. Box 1071

EXAMPLE:

P ART # DESCRIPTION QUANTITY
1 Rear Unit Assembly 1