SSAC TSD1 Series Data Sheet
TSD1 SeriesTimer - Delay-on-Make
Connection:
L1 N/L2
Load may be connected to terminal 3 or 1.
RT is used when external adjustment is ordered.
The TSD1 Series is designed for more demanding
commercial and industrial applications where small
size and accurate performance is required. The
factory calibration for xed time delays is within
1% of the target time delay. The repeat accuracy,
under stable conditions, is 0.1% of the time delay.
The TSD1 Series is rated to operate over an extended
temperature range. Time delays of 0.1 seconds to 100
hours are available. The output is rated 1A steady
and 10A inrush. The modules are totally solid state
and encapsulated to protect the electronic circuitry.
Operation (Delay-on-Make):
Upon application of input voltage, the time delay begins.
The output is de-energized before and during the time
delay. At the end of the time delay, the output energizes
and remains energized until input voltage is removed.
Reset: Removing input voltage resets the time delay
and output.
For more information see:
Appendix A, pages 156-164 for function descriptions
and diagrams.
Appendix B, page 165, Figure 1 for dimensional drawing.
External Resistance vs. Time Delay:
Features:
• Fixed or adjustable delays from 0.1s - 100h
• ±0.1% repeat accuracy
• ±1% factory calibration
• 12 to 230V in 6 ranges
• 1A, solid-state output
• Encapsulated
Approvals:
Auxiliary Products:
• External adjust potentiometer:
P/N: P10 04-95
P/N: P1004-95-X
• Female quick connect:
P / N : P 1 0 1 5 -6 4 ( AW G 1 4 / 1 6 )
• Quick connect to screw adaptor:
P/N: P1015-18
• Mounting bracket: P/N: P1023-6
• Versa-knob: P/N: P0700-7
• DIN rail: P/N: C103PM (Al)
• DIN rail adaptor: P/N: P1023-20
Available Models:
TSD11110S
TSD1311.2S
TSD1315S
TSD1320
TSD1321
TSD1424
If desired part number is not listed, please call
us to see if it is technically possible to build.
Order Table:
TSD1
X
Input Voltage
─1 - 12VDC
─2 - 24VAC
─3 - 24VDC
─4 - 120VAC
─5 - 120VDC
─6 - 230VAC
X
Adjustment
─1 - Fixed
─2 - External adjust
─3 - Onboard adjust
X
Time Delay*
─0 - 0.1 - 10s
─1 - 1 - 100s
─2 - 10 - 1000s
─3 - 0.1 - 10m
─4 - 1 - 100m
─5 - 10 - 1000m
─6 - 1 - 100h
Specications
Time Delay
Range ..............................0.1s - 100h in 7 adjustable ranges or xed
Repeat Accuracy ....................±0.1% or 20ms, whichever is greater
Tolerance (Factory Calibration) ........≤ ±1%
Recycle Time ........................≤ 150ms
Time Delay vs Temp. & Voltage ........≤ ±1%
Input
Voltage .............................12, 24, 120VDC; 24, 120, 230VAC
Tolerance ...........................±20%
AC Line Frequency ..................50/60 Hz
Output
Type ...............................Solid state
Form ...............................NO, open during timing
Maximum Load Current ..............1A steady state, 10A inrush at 60°C
Minimum Holding Current ...........≤ 40mA
Off State Leakage Current ............≅ 7mA @ 230VAC
Voltage Drop ........................≅ 2.5V @ 1A
*If xed delay is selected, insert
delay (0.1 - 1000) followed by (S) sec.
(M) min. or (1 - 100) (H) hours.
Protection
Circuitry ...........................Encapsulated
Dielectric Breakdown ................≥ 2000V RMS terminals to mounting surface
Insulation Resistance .................≥ 100 MΩ
Polarity ............................DC units are reverse polarity protected
Mechanical
Mounting ..........................Surface mount with one #10 (M5 x 0.8) screw
Dimensions .........................2 x 2 x 1.21 in. (50.8 x 50.8 x 30.7 mm)
Termination .........................0.25 in. (6.35 mm) male quick connect terminals
Environmental
Operating / Storage Temperature ......-40° to 75°C / -40° to 85°C
Humidity ...........................95% relative, non-condensing
Weight .............................≅ 2.4 oz (68 g)
Loading...