Spicer 34DS, 34RS, 38DS, 38RS, DS340 User Manual

...

Spicer® Single Drive Axles

Service Manual

Spicer® Single Drive Axles

AXSM-0041 September 2007

Table of Contents

Introduction .........................................................1

Failure Analysis ...................................................7

Inspection ...........................................................9

Differential Carrier Assembly - Parts .................11

Differential Lockout ...........................................17

Power Divider

Power Divider - Parts Exploded View........................ 23

Remove Power Divider............................................. 24

Remove Power Divider from Differential Carrier

(with carrier removed from axle housing) ................ 25

Disassemble, Assemble and Overhaul

the Power Divider..................................................... 27

Install Power Divider on Differential Carrier

(with carrier assembled to axle housing) .................. 38

Install Power Divider on Differential Carrier

(with carrier removed from axle housing) ................. 40

Dissasemble Differential Carrier

(with power divider removed) ...................................54

Drive Pinion

Drive Pinion - Parts Exploded View............................ 57

Disassemble and Overhaul Drive Pinion.................... 58

Install Drive Pinion Assembly.................................... 65

Wheel Differential Assembly Wheel Differential Assembly

- Parts Exploded View ............................................... 68

Housing and Rear Cover Assembly

- Parts Exploded View ............................................... 91

Seals ..................................................................92

Housing Breather ..............................................94

Wheel End Seal - Parts Exploded View .............95

Remove and Overhaul Wheel End Seal .............96

Wheel Adjustment Systems ..............................97

Verify Wheel End-play Procedure ......................99

Lubricate Wheel End .......................................100

Lubrication ......................................................102

Lube Change Intervals ....................................103

Change Lube ...................................................104

Standpipes ......................................................105

Torque Chart ...................................................107

Appendix

Wheel Differential Lock ...........................................109

Differential Lock Theory of Operation ....................110

Control Systems ....................................................111

Dual Range Axle Shift Systems ..............................113

Troubleshooting .....................................................120

Proper Vehicle Towing ...........................................122

Axle Shift System Components ..............................124

Inter-Axle Differential Lockout

With Interlock Control Valve (straight-air type) ......126

Theory of Operation ...............................................129

Power Flow and Torque Distribution ......................130

Lubrication .............................................................132

Torque Distribution in Low Range .........................136

Table of Contents

Out of Vehicle Resetting

Introduction Dana Corporation, presents this publication to aid in maintenance and overhaul of Dana tandem drive axles. Instructions contained herein cover four basic axle models. Their design is common, with differences in load capacity. Capacity variations are achieved by combining basic differential carrier assemblies in different axle housings, axle shafts and wheel equipment.

Load Capacity Model No.

34,000 lbs. . . . . . . . . . . . . .. DS340, 341

38,000 lbs. . . . . . . . . . . . . . . DS2380(P)

38,000 lbs. . . . . . . . . . . . . .. DS381(P)*

40,000 lbs. . . . . . . . . . . . . . . . DS400-P, DS401-P, DS402(P), DS403(P)

45,000 lbs.. . . . . . . . . . . . . .. DS451-P

Some models (identified with letter “P”) are equipped with a gear-driven pump, designed to provide additional lubrication to the inter-axle differential and related parts. Instructions contained herein are applicable to all axle models, unless specified otherwise.

For brake information and axle mounting or suspension systems, refer to pertinent truck manufacturer’s literature.

Typical Dana Single Reduction Tandem Axle

Two design variations of tandem axles are included in this manual. The major difference is in the shaft spline design. Note: DS381 (P) axles manufactured after April 1985 are rated at 40,000 lbs.

Axle and Carrier Assembly Model Identification

Drive Axle

General Information

Gear i n g

D - For war d Tan dem Axle R - Rear Tan dem Axle

S - S i ngle Redu ction D - S i n gle Reduction with Wheel Differ e n tial Lock T - Du al Ran ge P - Plan etar y Dou ble Reduction

Example:

D S = For ward Tan dem Axle/Sin gle Redu ction R S = Rear Tandem Axle/S in gle Redu ction

Note: Tags that do not include all the information shown here

are older models (before May 1987).

CUST. PART NO.

SPEC. SERIAL NO.

MODEL PART NO. RATIO

MADE IN:

Spicer

L u be Pu mp

P = S tan dar d (P) = Option al

Design Level

Capacity (x 1000 lbs.)

Example: 46 = 46,000 lbs .

Service Procedure

CUST. PART NO.

Spicer

SPEC. SERIAL NO.

MODEL PART NO. RATIO

MADE IN:

Data plate is located on

the axle centerline

CUST. PART NO.

SPEC. SERIAL NO.

MODEL PART NO. RATIO

MADE IN:

Spicer

Forward Axle (Side View) Rear Axle (Top View)

1 - Country or origin 2 - Axle model identification 3 - Specification number assigned to the axle built by Spicer. Identifies all component parts of the axle including special OEM requirements such as yokes or flanges. 4 - OEM part number assigned to the axle build 5 - Carrier assembly serial number assigned by the manufacturing plant 6 - Axle gear ratio 7 - Carrier assembly production or service part number

General Information

Part Identification

Axle Housing Axle Shaft

T P .

SH BL GSH

OH U DAM

ecipS

O N .

. P

A C .G

N .D

E . I .. G N I

1 - ID Tag 2 - Axle shaft part number

Axle Specification Number

The complete axle is identified by the specification number stamped on the side of the axle housing. This number identifies all component parts of the axle as built by Dana, including special OEM requirements such as yoke or flange. In addition, some axles may include a metal identification tage.

Ring Gear and Pinion

Note: Ring gear and drive pinion are matched parts and must

be replaced in sets.

General Information

Service Procedure

8307L

183721

RECIPS

41-8

2LN

14-8

721

RECIPS

824721

1 - Part number 2 - Number of ring gear teeth 3 - Manufacturing numbers 4 - Matching gear set number 5 - Number of pinion teeth 6 - Date code 7 - Indicates genuine Spicer parts 8 - Heat code

6-39

J D 7 7

5 0 4 58

8 6

EATON

General Information

Power Flow and Torque Distribution

Spicer tandem drive axles described in this publication are single reduction units designed primarily for highway or turnpike. They are also for a variety of other applications. This type of axle provides a vehicle with superior load carrying and roadability characteristics by dividing its work between two axles. The complete tandem assembly consists of two axles coupled by a power divider.

Lube Pump System

Power Divider

In operation, the power divider accepts the torque from the vehicle driveline and distributes it equally to the two axles. This assembly is of the two-gear design consisting of an input shaft, inter-axle differential, output shaft and two constant-mesh helical gears. The inter-axle differential compensates for axle speed variations in the same way the wheel differential works between the two wheels of a single drive axle. This unit also acts as a central point in distribution of torque to the two axles. The power divider also includes a driver-controlled, air-operated lockout. When lockout is engaged, it mechanically prevents inter-axle differentiation for better performance under poor traction conditions.

Gearing

The gearing for each axle is of the spiral bevel design with drive pinion positioned at centerline of the ring gear. The differential and drive pinion are mounted on tapered roller bearings. The wheel differential is a 4 pinion and 2 side gear design.

Lube Pump

Tandem Axles with suffix letter "P" in Model No. are equipped with a lube pump to provide positive lubrication to the inter- axle differential and other power divider parts. This pump is operated by a drive gear engaged with the input shaft splines. When vehicle is moving in a forward direction, pressurized lube is delivered to the vital power divider parts. The pump lube system incorporates a magnetic strainer screen. To keep the system clean, the magnet traps minute particles and the screen blocks out large particles of foreign material.

General Information

Torque Distribution with Lockout Disengaged (Inter-axle Differential is Operation)

Torque (power flow) from the vehicle driveline is transmitted to the input shaft and the inter-axle differential spider. At this point, the differential distributes torque equally to both axles. For the forward axle, torque is transmitted from the helical-side gear to the pinion helical gear, drive pinion, ring gear, wheel differential and axle shafts. For the rear axle, torque is transmitted from the output shaft side gear, through the output shaft, inter-axle driveline, to the drive pinion, ring gear, wheel differential and axle shafts.

Input torque

Lockout disengaged

Inter-axle differential

operating

Torque is transmitted to both axles through inter-axle differential action.

Drive is

from differential

through output

shaft to

rear gearing

Drive is from differential through helical gears to

forward gearing

Torque Distribution with Lockout Engaged (inter-axle Differential is Not Operation)

A lockout mechanism is incorporated in the power divider to enable the vehicle driver to lock out the inter-axle differential and provide maximum traction under adverse road conditions. In operation, an air cylinder (controlled by a cab-mounted valve) shifts a sliding clutch. To lock out inter-axle differential action, the clutch engages the helical-side gear and causes this gear, the input shaft and differential to rotate as one assembly. This action provides a positive drive to both axles. With Lockout engaged, torque is distributed to both-axles without differential action. The forward axle pinion and ring gear are driven by the helical side gear. The rear axle gearing is driven from the output shaft side gear and inter-axle driveline.

Service Procedure

Note: Varied road surface conditions can result in unequal torque distribution between the two axle assemblies.

Input torque

Lockout engaged

Inter-axle differential

not operating

Torque is transmitted to both axles without inter-axle differential action.

Drive is from input shaft

through helical gears to

Drive is from

output shaft side

gear to rear

gearing

forward gearing

Spicer Single Reduction Tandem Drive Axles

Differential Carrier Assembly Exploded View

Forward Axle Carrier Assembly (Single Speed) with Diff. Lock

52 53 54 56 57 58 55 6 1 5

Other Design Variations

23 24

DIFFERENTIAL

& RING GEAR

29 31 32 35 34 38 36 37 3435 28 27 26 25

19 15

Axle Series D340, 380(P),400-P D341, 381(P), 401-P, 402(P), 403(P), 451-P

Output Shaft Splines 16 16

Side Gear End 16 16

Output End 10 34

Input Shaft Splines

Input End 15 44

Diff End 36 36

Helical Gears 7 pitch 5 pitch

Drive Pinion Splines

Forward Axle 10 41

Rear Axle 10 39

Axle Shaft Side Gear Splines

D340- 16 D341- 39

D380(P)- 16 D381(P), 402(P), 403(P)- 41

D400(P)- 33 D401-P, 451-P- 33

Spicer Single Reduction Tandem Drive Axles

Axle Series D340, 380(P), 400-P, D341, 381(P), 401-P, 402(P), 403 (P), 451-P

INTER-AXLE

64 65

DIFFERENTIAL ASSEMBLY

Service Procedure

76 77

39 31 40

79 80 81 82 83

106

43 45

LUBE PUMP

444647

84 85 86 88 89 90

105

94 97 98 99

100

101

104 103 95

Note: Before Replacing Seals, Yokes, and Slingers, refer to the Repair and Replacement Instructions for interchangeability infor-

mation.

102

Spicer Single Reduction Tandem Drive Axles

1 - Differential carrier & bearing caps 2 - Bearing capscrew 3 - Flat washer 4 - Lockwire 5 - Dowel bushing 6 - Bearing cap adjuster lock (RH) 7 - Capscrew 8 - Bearing cap adjuster lock (LH) 9 - Cotter pin (LH) 10 - Expansion plug (upper) 11 -Expansion plug (lower) 12 - Filler plug 13 - Shift fork shaft 14 - Carrier cover dowel pun

Shi

15 16 - Shift fork seal & spring assembly 17 - Flat washer 18 - Stud nut 19 - Shift fork & roller assembly 20 - Shift unit assembly 21 - Sliding clutch 22 - Differential bearing adjuster (RH) 23 - Differential bearing cup (RH) 24 - Differential bearing cone (RH) 25 - Differential bearing adjuster (LH) 2 27 - Differential bearing cone (LH) 28 - Differential case (plain half) 29 - Differential case (flanged half) 30 - Differential case capscrew 31 - Ring gear & drive pinion 32 - Bolt 33 - Nut 34 - Differential side gear 36 - Side pinion

ft unit mounting stud

6 - Differen

tial bearing cup (LH)

37 - Side pinion thrust washer 38 - Spider

t bearin

39 - Pinion pilo 40 - Pinion bearing cone 41 - Pinion bearing spacer washer 42 - Pinion bearing spacer 43 - Pinion bearing cup 44 - Pinion bearing cage 45 - Pinion bearing cage shim 46 - Lock washer 47 - Bearing cage capscrew 48 - Pinion helical gear 49 - Outer pinion support bearing (one piece) 50 - Pinion shaft end nut 51 - Pinion nut spring p 52 - Outpu 53 - Output shaft washer 54 - Rear bearing retaining washer 55 - Axle housing cover 56 - Output shaft oil seal 57 - Bearing snap ring 58 - Output shaft bearing 59 - Filler plug 60 - Output shaft 61 - Output shaft bushing 62 - Output shaft O-ring 63 - Output shaft bearing cup 64 - Output shaft bearing cone 65 - Output shaft side gear 66 - Side gear snap ring 67 - Output shaft compression spring 68 - Output shaft thrust bearing 69 - Inter-axle differential assemble 70 - Inter-axle differential case half 71 - Case bo

t shaft nut

72 - Case nut 73 - Side pinio 74 - Side pinion thrust washer 75 - Spider 76 - Helical side gear snap ring 77- Helical side gear 78 - Helical side gear bushing 79 - Helical side gear thrust washer 80 - Helical side gear “D” washer 81 - Lo 82 - Inp 83 - Input shaft bearing cone 84 - Input shaft bearing cup 85 - Input cover shim 86 - Input bearing cover 87 - Bearing cover capscrew 88 - Input shaft oil seal 89 - Input shaft nut washer 90 - Input shaft nut 91 - PDU carrier cover 92 - Carrier cover capscrew 93 - Lock 94 - Pipe plug 95 - Exp 96 - Magnetic filter screen 97 - Pump gear & shaft assembly 98 - Cover O-ring 99 - Lube pump cover 100 - Lock washer 101 - Cover capscrew 102 - Cover d 103 - Pump drive gear 104 - Drive gea 105 - Air-operated lockout assembly 106 - Shift fork & push rod assembly

ckout sliding clutch

ut shaft

washer

ansion plug

owel pin

r locknut

Spicer Single Reduction Tandem Drive Axles

Differential Carrier Assembly

Rear Axle RS340, 341, 380, 400, 401, 402, 403, 451

10 11 12 15 18 20 21 17 18 13 15 12 11 10

16 17 19 14 14

Service Procedure

243 6

6 5 1 1 22 23 24 29 31 32

1 - Differential carrier & bearing caps 2 - Bearing capscrew 3 - Flat washer 4 - Lockwire 5 - Bearing cap adjuster lock 6 - Cotter pin 7 - Dowel bushing 8 - Ring gear thrust screw 9 - Thrust screw jam nut 10 - Differential bearing adjuster 11 - Differential bearing cup

8 9 27 26 28 25 26 23 30 33

12 - Differential bearing cone 13 - Ring gear & drive pinion 14 - Bolt and nut 15 - Differential case (flanged half) 16 - Differential case capscrew 17 - Differential side gear 18 - Side gear thrust washer 19 - Side pinion 20 - Side pinion thrust washer 21 - Spider 22 - Pinion pilot bearing

23 - Pinion bearing cone 24 - Pinion bearing spacer 25 - Pinion bearing cage 26 - Pinion bearing cup 27 - Pinion bearing spacer washer 28 - Pinion bearing cage shim 29 - Bearing cage capscrew 30 - Oil seal 31 - Input yoke 32 - Flat washer 33 - Pinion nut

Lubrication

The ability of a drive axle to deliver quiet, trouble free operation over a period of years is largely dependent upon the use of good quality gear lubricant in correct quantity. The most satisfactory results can be obtained by following the directions contained in this manual. The following lubrication instructions represent the most current recommendations from Dana Corporation.

Approved Lubricants

General—Gear lubrications acceptable under military specification (MILSPEC) MIL-L-2105D (Lubricating Oils, Gear, Multipurpose) are approved for use in for multigrade oils. It supersedes both MIL-L-2105B, MIL-L-2105C and cold weather specification MlL-L-l 0324A. This specification applies to both petroleum-based and synthetic based gear lubricants if they appear on the most current “Qualified Products List” (QPL-2105) for MIL-L-2105D. Note: The use of separate oil additives and/or friction modifiers are not approved in Dana Drive Axles.

Synthetic based — Synthetic-based gear lubricants exhibit superior thermal and oxidation stability, and generally degrade at a lower rate when compared to petroleum-based lubricants. The performance characteristics of these lubricants include extended change intervals, improved fuel economy, better extreme temperature operation, reduced wear and cleaner component appearance. The family of Spicer TM gear lubricants represents a premium quality synthetic lube which fully meets or exceeds the requirements of MIL-L-2105D. These products, available in both 75W-90 and 80 W-140, have demonstrated superior performance in comparison to others qualified under the MILSPEC, as demonstrated by extensive laboratory and field testing. For a complete list of Spicer ® approved synthetic lubricants contact your local Spicer representative. See back cover of this manual for appropriate phone number.

Spicer Drive Axles. The MIL-L-2105D specif

ication defines performance and viscosity requirements

Makeup Lube — Maximum amount of non-synthetic makeup lube is 100/o.

Viscosity / Ambient Temperature Recommendations -The following chart lists the varies SAE Grades covered by MIL-L- 2105D and the associated ambient temperature range from each. Those SAE grades shown with an asterisk (*). are available in the Roadranger family of synthetic gear lubricants.

The lowest ambient temperatures covered by this chart are -40°F and -40°C. Lubrication recommendations for those applications which consistently operate below this temperature range, must be obtained through tcontacting your local Spicer epresentative.

Grade Ambient Temperature

75W - 40 F to -150 F (-40 C to -26 C)

75W-80 - 40 F to 80 F (-40 C to 21 C)

75W-90 - 40 F to 100 F (-40 C to 38 C)

75W-140 - 40 F and above (-40 C and above)

80W-90 - 40 F to 100 F (-40 C to -38 C)

80W-140 - 40 F and above(-40 C and above)

85W-140 - 40 F and above (-40 C and above)

Lubrication

Lube Change Intervals

This product combines the latest manufacturing and part washing technology. When filled with an Spicer approved synthetic lubricant at the factory, the initial drain is not required.

Change the lubricant within the first 5,000 miles of operation when not using a new

axle or after a carrier head replacement. Base subsequent lubricant changes on a combination of the following chart and

user assessment of the application and operating environment.

Severe Service Lubrication Change Intervals-Severe service applications are those where the vehicle consistently operates at or near its maximum GCW or GVW ratings, dusty or wet environments, or consistent operation on grades greater than 8%. For these applications, the ON/OFF HIGHWAY portion of the chart should be used. Typical applications are construction, logging, mining and refuse removal. Note: Remove metallic particles from the magnetic filler plug and drain plugs. Clean or replace the breather at each lubricant

change.

Spicer approved synthetic lubricant in either a

Guide Lines - Lube Change Intervals for Drive Axles

Lubricant Type On-Highway Miles Maximum change In-

terval

Mineral Based 100,000 Yearly 40,000 Yearly

Roadranger Approved Lubricant

250,000 3 Years 100,000 Yearly

On/Off Highway Severe Service Miles

Maximum Change Interval

Changing Lube

Draining

Drain when the lube is at normal operating temperature. It will run freely and minimize the time necessary to fully drain the axle. Unscrew the magnetic drain plug on the underside of the axle housing and allow the lube to drain into a suitable container. Inspect drain plug for large quantities of metal particles. After initial oil change, these are signs of damage or extreme wear in the axle, and inspection of the entire unit may be warranted. Clean the drain plug and replace it after the lube has drained completely.

Service Procedure

Axles with Lube Pump: Remove the magnetic strainer from the power divider cover and inspect for wear material in the same manner as the drain plug. Wash the magnetic strainer in solvent and blow dry with compressed air to remove oil and metal particles.

CAUTION

Exercise care to direct compressed air into safe area. Wear safety glasses.

Lubrication

Filling

Remove the filler hole plug from the center of the axle housing cover and fill the axle with approved lubricant until level with the bottom of the hole.

Forward axles: Add two pints (0.94 liters) of lubricant through filler hole at the top of the differential carrier near the power divider cover.

Oil Filler Hole at top of Differential Carrier Magnetic Strainer for Axle with Lube Pump

Note: Lube fill capacities in the adjacent chart are good guidelines but will vary somewhat on the basis of the angle the axle is

installed in a particular chassis. Always use the filler hole as the final reference. If lube is level with the bottom of the hole, the axle is properly filled.

Axle Installation Angles

Axles installed at angles exceeding 10 degrees or operated regularly in areas of continuous and lengthy grades may require standpipes to allow proper fill levels.

For specific recommendations, contact your local

Spicer representative. See back cover of

this manual for phone numbers.

Lube Capacities, Dana Housings

Single Reduction Tandem Series Forward Axle Pints (liters) Rear Axle Pints (liters)

380(P), 381(P), 400-P, 401-P 39 (18.5) 36 (17.0)

402(P), 403(P),451-P 39 (18.5) 36 (17.0)

Forward Axle: Add an additional 2 pints divider cover.

Capacities listed are approximate. The amount of lubricant will vary with angle of axle as installed in vehicle chassis.

(0.94 liters) axle lubricant through filler hole at the top of differential carrier near the power

Lubrication

Wheel End Lubrication

IMPORTANT

Before operating the axle, the wheel hub cavities and bearings must be lubricated to prevent failure. When wheel ends are serviced, follow Spicer’s wheel end lubrication procedure before operating the axle.

Spicer axles may be equipped with either of tw

• Wheel en

ds with an oil fill hole.

o wheel end designs:

• Wheel ends without an oil fill hole.

Wheel Ends with an oil fill hole proceed as follows: (Fig. 1)

1. Rotate the wheel end hub until the oil fill hole is up.

2. Remove the oil fill plug.

3. Pour 1/2 pint of axle sump lubricant into each hub through the wheel end fill hole.

4. Install oil fill plug and tighten to specified torque.

Wheel End with Oil Fill Hole

WHEEL END

OIL FILL HOLE

Wheel End without Oil Fill Hole

Service Procedure

LUBRICANT

FLOW

FROM SUMP

PROPER

LUBRICANT

LEVEL

Fig. 1 Cutaway views of typical wheel and assemblies

PROPER

LUBRICANT

LEVEL

Lubrication

Wheel Ends without an oil fill hole proceed as follows: (Fig. 2)

1. With axle level and wheel ends assembled, add lubricant through filler hole in axle housing cover until fluid is level with the bottom of filler hole.

2. Raise the left side of the axle 6 inches or more. Hold axle in this position for one minute.

3. Lower the left side.

4. Raise the right side of the axle 6 inches or more. Hold axle in this position for one minute.

5. Lower the right side.

6. With axle on a level surface, add lubricant through housing cover oil filler hole until fluid is level with the bottom of the hole.

Note: Axles without wheel end fill holes will require approximately 2.5 additional pints of lubricant to bring the lube level even with

the bottom of fill hole.

WITH AXLE ON LEVEL

SURFACE FILL HOUSING

WITH OIL TO BOTTOM OF PLUG

TEMPERATURE SENSOR

MOUNTING HOLE

Fig. 2 Wheel end lubrication procedure

OIL WILL

RUN INTO

WHEEL END

TILT HOUSING SIDE TO SIDE, 1 MINUTE PER SIDE, THEN,

RECHECK OIL LEVEL IN AXLE

OIL WILL

RUN INTO

WHEEL END

General Information

Cleaning, Inspection, Replacement

As the drive axle is disassembled, set all parts aside for thorough cleaning and inspection. Careful inspection will help determine whether parts should be reused. In many cases, the causes of premature wear or drive axle failure will also be revealed.

Cleaning

The differential carrier assembly may be steam-cleaned while mounted in the housing as long as all openings are tightly plugged. Once removed from its housing, do not steam clean differential carrier or any components. Steam cleaning at this time could allow water to be trapped in cored passages, leading to rust, lubricant contamination, and premature component wear. The only proper way to clean the assembly is to disassemble it completely. Other methods will not be effective except as preparatory steps in the process. Wash steel parts with ground or polished surfaces in solvent. There are many suitable commercial solvents available. Kerosene and diesel fuel are acceptable.

WARNING

Gasoline is not an acceptable solvent because of its extreme combustibiliy. It is unsafe in the workshop environment.

Service Procedure

Wash castings or other rough parts in solvent or clean in hot solution tanks using mild alkali solutions. If a hot solution tank is used, make sure parts are heated thoroughly, before rinsing.

Rinse thoroughly to remove all traces of the cleaning solution. Dry parts immediately with clean rags.

Lightly oil parts if they are to be reused immediately. Otherwise, coat with oil and

wrap in corrosion-resistant paper. Store parts in a clean, dry place.

Inspection

Inspect steel parts for notches, visible steps or grooves created by wear. Look for pitting or cracking along gear contact lines. Scuffing, deformation or discoloration are signs of excessive heat in the axle, usually related to low lubricant levels or improper lubrication practices.

Before reusing a gear set, inspect teeth for signs of excessive wear. Check tooth contact pattern for evidence of incorrect adjustment (see Adjustment Section for correct pattern). Inspect machined surfaces of cast or malleable parts. They must be free of cracks, scoring, and wear. Look for elongation of drilled holes, wear on surfaces machined for bearing fits and nicks or burrs in mating surfaces.

Inspect fasteners for rounded heads, bends, cracks or damaged threads. The axle housing should be examined for cracks or leaks. Also look for loose studs or cross-threaded holes. Inspect machined surfaces for nicks and burrs.

General Information

Repair and Replacement

IMPORTANT

To achieve maximum value from an axle rebuild. Replace lower-cost parts, such as thrust washers, seals, etc. These items protect the axle from premature wear or loss of lubricants. Replacing these parts will not increase rebuild cost significantly.

It is also important to replace other parts which display signs of heavy wear even though not cracked or broken. A significant portion of such a parts useful life has been expended and the damage caused, should the part fail, is far in excess of its cost.

Steel Parts- Gear sets, input and output shafts, differential parts and bearings are not repairable. Worn or damaged parts should be discarded without hesitation. Also discard mating parts in some cases. Gear sets, for example, must be replaced in sets.

Miscellaneous Parts - Seals and washers are routinely replaced. None of these parts can be reused if damaged. Fasteners using self-locking nylon patches may be reused if not damaged, but should be secured by a few drops of Loctite #277 on the threaded surface of the hole during installation and carefully torqued during installation.

Axle Housings - Repairs are limited to removal of nicks or burrs on machined surfaces and the replacement of loose or broken studs.

CAUTION

Any damage which affects the alignment or structural integrity of the housing requires housing replacement. Repair by welding or straightening should not be attempted. This process can affect the housing heat treatment and cause it to fail completely when under load.

Silicone Rubber Gasket Compound - For more effective sealing. majority of metal-to-metal mating surfaces.

Spicer includes gasket compound and application instructions in many repair parts kits.

mmended that this

is reco

It against lube and is easier to remove from mating surfaces when replacing parts.

Seals, Yoke & Slinger Service Information

During the 4th Quarter of 1990, new seals and yoke & slingers were used on the models in this publication. The new seals and slingers are noticeably different from the current seals and will affect interchangeability.

The upgraded seals can be used on axles originally equipped with the old seals.

Dana recommends the replacement of old yoke & slinger assemblies when the new seals are installed.

The old yokes and slingers will work with the new seals, but new yoke and slinger assemblies provide maximum sealing protection and prevent premature seal wear due to poor yoke condition.

New yoke and slinger assemblies cannot be used with the old seal design on the tandem forward axles.

New yoke and slinger assemblies can be used with the old seal on the tandem rear pinions.

Yoke Assembly & Oil Seal Kits contain oil seal, yoke & slinger and instructions.

Most non-Dana aftermarket seals will not be compatible with the new Dana Yoke and Slinger assemblies.

Spcier recommends the use of special installation tools conveniently packaged in one single kit (listed below

compound be used in place of conventional gaskets. The compound will provide a more effective seal

Spicer uses silicone rubber gasket compound to seal the

Refer to Dana parts Boo

Seal Driver Installation Kit 272139

126917 Driver (Rear Axle Pinion)

127787 Adapter (use with 126917 Driver for Forward Axle Input)

127786 Driver (Forward Axle Output)

k AXIP-0089 and Eaton Bulletin 90-06 for additional information.

Adjustments

Wheel Bearing Adjustment

Special Instructions

WARNING

Never work under a vehicle supported by only a jack. Always support vehicle with stands. Block the wheels and make sure the vehicle will not roll before releasing the brakes.

Procedure - Wheel End Seal

1. Remove:

• The outer bearing and wheel.

• The inner bearing.

• The oil seal or grease retainer and discard.

• The old wear sleeve (2-piece design only) with a ball peen hammer and discard.

IMPORTANT

Wheel end seals can be easily damaged during handling. Leave the seal in its package until installation to prevent damage or contamination.

CAUTION

Do not cut through the old wear sleeve. Damage to the housing may result.

2. Inspect:

• The spindle journal and hub bore for scratches or burns. Recondition with emery cloth as required.

Note: Deep gouges can be repaired by filling gouge with hardened gasket and smoothing with emery cloth.

3. Clean:

• The hub cavity and bearing bores before reassembly. Be sure to remove contaminants from all recesses and corners.

Service Procedure

• The bearings thoroughly with solvent and examine for damage. Replace damaged or worn bearings.

• Before installation, lubricate with the same lubricant used in the axle sump.

• The inner bearing.

• The wheel seal following the directors provided by the seal supplier.

IMPORTANT

Always use the seal installation tool specified by the seal manufacturer. Using an improper tool can distort or damage the seal and cause premature seal failure.

Procedure - Wheel Bearing Adjustment

1. Identify the wheel nut system being installed. Three systems are available:

• Three piece Dowel-type wheel nut system -Fig.1

• Three piece Tang-type wheel nut system - Fig.2

Adjustments

• Four piece Tang/Dowel type wheel nut system - Fig.3

WARNING

Do not mix spindle nuts and lock washers from different systems. Mixing spindle nuts and lock washers can cause wheel separation.

Note: The lock washer for a four piece-dowel-type wheel system is thinner than the lock washer for a three piece tang-type

wheel nut system and is not designed to bear against the inner nut.

Fig 1

Outer nut

(P/N 119881)

Inner nut

(P/N 119882)

Dowel Pin

Dowel-type Lock

Washer (P/N 119883)

Fig 2

Outer nut

(P/N 11249)

Inner nut

(P/N 11249)

Tang-type lock washer

(P/N 119883) 0.123" thick

Fig 3

Outer nut (P/N 119881)

Tang-type lock washer (P/N 129132) .0478" thick

Inner nut (P/N 119882)

Dowel pin

Dowel-type lock washer (P/N 119883)

2. Inspect the spindle and nut threads for corrosion and clean thoroughly or replace as required.

Note: Proper assembly and adjustment is not possible if the spindle or nut threads are corroded.

• lnspect the tang-type washer (if used). Replace the washer if the tangs are broken, cracked, or damaged.

3. Install the hub and drum on the spindle with care to prevent damage or distortion to the wheel seal.

CAUTION

A wheel dolly is recommended during installation to make sure that the wheel seal is not damaged by the weight of the hub and drum. Never support the hub on the spindle with just the inner bearing and seal. This can damage the seal and cause premature failure.

• Completely fill the hub cavity between the inner and outer bearing races with the same lubricant used in the axle sump.

4. Before installation, lubricate the outer bearing with the same lubricant used in the axle sump.

Note: Lubricate only with clean axle lubricant of the same type used in the axle sump. Do not pack the bearing with grease

before installation. Grease will prevent the proper circulation of axle lubricant and may cause wheel seal failure.

5. Install the outer bearing on the spindle.

• Install the inner nut on the spindle.

• Tighten the inner nut to 200 lbs. ft. (271 N.M.) while rotating the wheel hub.

CAUTION

Never use an impact wrench to adjust wheel bearings. A torque wrench is required to assure that the nuts are property

Adjustments

tightened.

6. Back-off the inner nut one full turn. Rotate the wheel hub.

7. Re-tighten the inner nut to 50 lbs. ft. (68 N.M.) while rotating the wheel hub.

8. Back-off the inner nut exactly 1/4 turn.

Note: This adjustment procedure allows the wheel to rotate freely with 0.001"-0.005" (0.025mm to 0.1 27mm) end-play.

9. Install the correct lock washer for the wheel nut system being used.

Procedure - Three piece tang-type lock washer system (see Fig. 2).

1. Install the Tang-type lock washer on the spindle.

IMPORTANT

Never tighten the inner nut for alignment. This can preload the bearing and cause premature failure.

2. Install the outer nut on the spindle and tighten to 250 lbs. ft. (339 N.M.).

Service Procedure

3. Verify end-play (see End Play Verification Procedure)

4. After verifying end play, secure wheel nuts by bending one of the locking washer tangs over the outer wheel nut and another tang over the inner wheel nut as shown in Figure 4. (below)

Bend two tangs…

one over inner nut

and one over

outer nut

Outer nut

Spindle

Inner nut

Lockwasher

Procedure - Three piece dowel-type lock washer system (see Fig. 1)

1. Install the Dowel-type lock washer on the spindle.

Note: If the dowel pin and washer are not aligned, remove washer, turn it over and reinstall. If required, loosen the inner nut

just enough for alignment.

IMPORTANT

Never tighten the inner nut for alignment. This can preload the bearing and cause premature failure.

Adjustments

2. Install the outer nut on the spindle and tighten to 350 lbs. ft. (475 N.M.).

3. Verify end-play (see End Play Verification Procedure)

Procedure - Four piece tang/dowel-type lock washer system (see Fig. 3)

1. First, install the Dowel-type lock washer on the spindle.

Note: If the dowel pin and washer are not aligned, remove washer, turn it over and reinstall. If required loosen the inner nut

just enough for alignment.

IMPORTANT

Never tighten the inner nut for alignment. This can preload the bearing and cause premature failure.

2. Install the Tang-type lock washer on the spindle.

3. Install the outer nut on the spindle and tighten to 250 lbs. ft. (339 N. M.)

4. Verify end-play (see End Play Verification Procedure)

5. After verifying end play, secure the outer nut by bending two opposing (180° apart) tangs of the locking washer over the outer nut as shown in Figure 5.

Figure 5

Bend two tangs

over outer nut

Spindle

Inner nut

Dowel pin

Outer nut

Lockwasher

Procedure - Install

1. Install a new gasket at axle shaft flange.

2. Install axle shaft.

3. Install axle flange nuts and tighten to specified torque.

4. Lubricate axle wheel ends (see Wheel End Lubrication Procedure)

Procedure - End Play Verification Procedure

1. Verify that end-play meets specification using a dial indicator. An indicator with 0.001” (0.03 mm) resolution is required.

Wheel end play is the free movement of the tire and wheel assembly along the spindle axis.

2. Attach a dial indicator with its magnetic base to the hub or brake drum as shown below:

Adjustments

Service Procedure

End Play Adjustment

with Tire & Wheel

Assembly

3. Adjust the dial indicator so that its plunger or pointer is against the end of the spindle with its line of action approximately parallel to the axis of the spindle.

4. Grasp the wheel assembly at the 3 o’clock and 9 o’clock positions. Push the wheel assembly in and out while oscillating it to seat the bearings. Read bearing end play as the total indicator movement.

CAUTION

If end play is not within specification, readjustment is required.

With indicator mounted at bottom,

Push/Pull at sides of drum

End Play Adjustment

with Wheel hub

Procedure - End Play Readjustment Procedure

1. Excessive End Play - If end play is greater than.005” (.127 mm), remove the outer nut and pull the lock washer away from the inner nut, but not off the spindle. Tighten the inner nut to the next alignment hole of the dowel-type washer (if used). Reassemble the washer and torque the outer nut. Verify end play with a dial indicator.

2. Insufficient End Play - If end play is not present, remove the outer nut and pull the lock washer away from the inner nut, but not off the spindle. Loosen the inner nut to the next adjustment hole of the dowel-type washer (if used). Reassemble the washer and re-torque the outer nut. Verify end play with a dial indicator.

3. Fine Tuning the End Play - If, after performing the readjustment procedures, end play is still not within the.001”-.005” (.025 mm to.127 mm) range, disassemble and inspect the components. If parts are found to be defective, replace the defective parts, reassemble and repeat wheel bearing adjustment procedure. Verify end play with a dial indicator.

Adjustments

Differential Carrier Adjustments

Adjustments help provide optimum axle life and performance by correctly positioning bearings and gears under load. The tandem axles covered in this manual require the following adjustments:

Bearing Preload: This adjustment is performed for both pinion and differential bearings. It maintains proper gear alignments by creating correct bearing cone and cup relationships for free rotation under load. The pinion pilot bearing does not require a preload adjustment.

Ring Gear Tooth Contact: This adjustment positions ring gear and pinion for best contact under load. Correct adjustment distributes torque evenly over gear teeth and helps maximize gear set Iife.

Input Shaft End Play (Forward Axles): This adjustment controls gear mesh in the inter-axle differential. Proper adjustment helps maximize life of all power divider parts.

Adjust Input Shaft End Play

Specifications: Input shaft end play requirements will vary with operating conditions, mileage and rebuild procedures. These vari-

ations are shown in the following chart.

Input Shaft End Play

New or Rebuild with new parts: 0.003" to 0.007".

Rebuild with reused parts: 0.013" to 0.017". Note: Because of manufacturing variations in individual parts, correctly adjusted end play could vary 0.010", after the unit is ro-

tated.

Acceptable End Play Tolerances when measuring as a regular maintenance procedure with axle in truck.

Up to 0.060" with over 100,000 miles or 1 year service off-road.

Up to 0.040" with less than 100,000 miles or 1 year service on- road.

Note: If end play exceeds limits, disassemble power divider and replace worn parts.

Procedure - Measure and Adjust End Play

IMPORTANT

In September 1988, a Spring and a Thrust Button between the input and output shafts. End play tolerances are the same for axles with or without this Spring and Button. However, end play measurement procedure is different than described below. Refer to Service Bulletin Supplement at back of this manual for procedure variances.

With power divider assembled to differential carrier, measure end play with dial indicator positioned at yoke end of input shaft. Move input shaft axially and measure end play. If end play is not correct (see chart), adjust as follows.

2. Remove input shaft nut, flat washer and yoke. Remove bearing cover cap screws and lock washers. Remove cover and shim pack.

3. To increase end play, add shims:

Desired end play: 0.003" to 0.007"

Measured endplay (Step 1): 0.001" - 0.001"

Add shims to provide desired end play : 0.002" to 0.006"

Adjustments

4. To decrease end play, remove shims:

Measured end play (Step 1): 0.015" - 0.015"

Desired end play: 0.003" to 0.007"

Remove shims to provide desired end play : 0.012" to 0.008"

5. To reassemble input shaft, install the adjusted shim pack and bearing cover. Install cap screws and lock washers. Torque screws to 75-85 ft. lbs. (101-115 N.m).

Dial indicator

U-bracket

Pry bar

Input shaft

Lift up on pry bar to compress input shaft.

Measuring End Play with Dial Indicator

Note: If difficulty is experienced in achieving correct torque on the input yoke nut, torque the nut with truck on the ground

and axle shafts installed.

6. Install yoke, flat washer and nut. Tighten nut snugly. Tap end of input shaft lightly to seat bearings.

7. Measure input shaft end play with dial indicator. If end play is still incorrect, repeat Steps 2 through 6.

8. With end play correct, seal shim pack to prevent lube leakage, then torque input shaft nut and cover cap screws (see chart).

Service Procedure

Note: When power divider has been disassembled and reassembled, it may be desirable to adjust end play by measuring bear-

ing cover clearance and calculating shim pack size. For procedures, see page 39.

Torque Chart

ft. lbs. N.m

Input Shaft Nut

1 5/8 - 18 780-960 1057 - 1301

*M42 x 1.5 840 - 1020 1140 - 1383

Bearing Cover Capscrew

1/2 - 13 75 - 85 101 - 115

*Metric Nut used on Axles produced after 1-3-95

Adjustments

Pinion Bearing Preload

Special Instructions

Most late model axles are provided with a “press-fit” outer bearing on the drive pinion. Some of the early model axles use an outer bearing which slips over the drive pinion. Procedures for adjusting both types of pinion bearing design are contained in this section.

Procedure - Adjust Pinion Bearing Preload for Axles with “Press-fit” Outer Pinion Bearings

1. Trial Build-up

Assemble pinion bearing cage, bearings and spacer (without drive pinion or oil seal). Center bearing spacer between two bearing cones.

Assemble these Parts for

Trial Build-up.

Inter

Inner

bearing

cone

Inter

Inner

bearing

cup

Bearing spacer

Bearing

(variable)

spacer (variable)

Outer

bearing

cup

Bearing cage

Outer

bearing

cone

Note: When new gear set or pinion bearings are used, select nominal size spacer from the specification chart below. If orig-

inal parts are used, use spacer removed during disassembly.

2. With the bearings well lubricated, place the assembly in the press. Position sleeve so that load is applied directly to the backface of the outer bearing cone.

Cage in Press to Check Bearing

Preload.

Press

Ram

Press ram

Sleeve Must

Sleeve must

Apply Pressure

apply pressure to

To Back Face

back face of

Of Outer

outer bearing

Bearing Cone

cone

Spring scale

Spring

Scale

Adjustments

3. Apply press load (see chart below) to the assembly and check rolling torque. Wrap soft wire around the bearing cage, attach spring scale and pull. Preload is correct when torque required to rotate the pinion bearing cage is from 10-20 in. lbs.. This specification is translated into spring scale readings in the chart below.

Specifications for Pinion Bearing Trial Build-up Preload Test (“Press-fit” Outer Pinion Bearings)

Nominal Bearing Spacer Thickness

Axle Models in. mm Tons Metric Tons lbs. Kgs.

Forward Axles

D340, 380(P), 400-P

D341, 381, (P), 401-P, 402(P), 403(P), 451-P

Rear Axles 0.638 16.21 14 - 15 127 - 136 4-8 18-

4. If necessary, Adjust Pinion Bearing Preload by changing the pinion bearing spacer. A thicker spacer will decrease preload. A thinner spacer will increase preload.

0.638 16.21 13.5 - 15.5 122- 140 3-7 2-3

0.496 12.60 17 - 19 154 - 172 3-7 1.4-

Press Loads

IMPORTANT

Spring Scale Reading (without pinion seal) (for 10-20 in. lbs. torque) (1.1-

2.3 N.m)

Once correct bearing preload has been established, note the spacer size used. Select a spacer

0.001” larger for use in the final pinion bearing cage assembly. The larger spacer compensates for slight “growth” in the bearings which occurs when they are pressed on the pinion shank. The trial build-up will result in proper pinion bearing preload in three of four cases.

Service Procedure

Do not assume that all assemblies will retain proper preload once bearings are pressed on pinion shank. Final preload test must be made in every case.

Adjustments

Final Pinion Bearing Preload Test

Procedure -

1. Assemble the complete pinion bearing cage unit as recommending the assembly section of this manual.

Measuring Bearing Preload with Pinion in Vise

Note: Forward axle pinion is equipped with helical gear. For easier disassembly during bearing adjustment procedure, use a

dummy yoke (if available) in place of helical gear.

2. Apply clamp load to the pinion bearing cage assembly. Either install the yoke (or helical gear) and torque the pinion nut to specifications or use a press to simulate nut torque (see chart below).

Vise Method - If the yoke and nut are used, mount the assembly in a vise, clamping yoke firmly.

Press Method - If a press is used, position a sleeve or spacer so that load is applied directly to the back-face of the outer bearing cone.

Measuring Bearing Preload with Pinion in Press

3. Measure Pinion Bearing Preload - Use a spring scale to test the assembly rolling torque. To use the spring scale, wrap soft wire around the bearing cage, attach the scale and pull. Preload is correct when torque required to rotate the pinion bearing cage is from 15 to 35 in. lbs.. This specification is translated into spring scale readings in the chart below.

+ 68 hidden pages