Quick Star t Guide
O4VB2M
Welcome
Thank you fo r pur cha sin g thi s network ca mer a!
This owner 's ma nua l is de signed to be a refe ren ce to ol fo r you r system.
Please read this manual carefully before operating the unit and retain it for future reference.
Should you require any technical assistance, cont act Speco Technologies Tech Support at
1-800-645-5516
Important Safeguards and Warning
1. Elec trica l safet y
All instal lat ion a nd op era tion here sh oul d con for m to lo cal electrica l saf ety c ode s.
Use a certif ied /li ste d 12V DC Class 2 pow er su ppl y onl y.
Please not e: Do n ot co nne ct tw o power supp lyi ng so urc es to t he device at the sa me ti me;
it may resul t in de vic e dam age ! The p rod uct must be groun ded t o red uce t he ri sk of
electric s hoc k.
Improper h and lin g and /or i nstallat ion c oul d run t he ri sk of fire or elect ric al sh ock .
2. Envi ronme nt
Heavy stre ss, v iol ent v ibr ation or exp osu re to w ate r is no t allowed durin g tra nsp ort ation,
storage an d ins tal lat ion .
This produ ct sh oul d be in stalled in a cool , dry p lac e awa y fro m direct sunlig ht an d hea t
sources.
Do not insta ll th e pro duc t in ex treme temp era tur e con dit ions.
Do not expos e the c ame ra to e lec tromagne tic r adi ati on. O therwise it may r esu lt in C MOS
sensor fai lur e.
Do not block a ny ve nti lat ion o penings.
Do not allow w ate r and l iqu id in trusion in to th e cam era .
3. Oper ation a nd Dail y Maint enanc e
Please shu t dow n the d evi ce an d then unplu g the p owe r cab le be fore you begin an y
maintena nce w ork .
Do not touch th e CMOS se nsor optic component . You can use a blower to clean the dust on
the le ns sur face .
Always use t he dr y sof t clo th to c lean the dev ice . If th ere i s too m uch dust, use a clo th
dampened w ith a s mal l qua nti ty of neutra l det ergent . Fin all y use t he dr y cloth to clean
the device .
Please use a professional optical cleaning method to clean the enclosu re. Improper enclosure
cleaning ( suc h as us ing c lot h) may resul t in po or IR f unc tio nality and/or I R ref lec tio n.
The ground ing h ole s of th e pro duct are rec omm end ed to b e gro unded to furthe r enh anc e
the reliab ili ty of t he ca mer a.
Dome cover i s an op tic al de vic e, please do n't t ouc h or wi pe co ver surface dir ect ly du rin g
installa tio n and u se, p lea se refer to th e fol low ing m eth ods if dirt is foun d:
Stained wi th di rt: U se oi l-f ree soft bru sh or h air d rye r to re move it gently.
Stained wi th gr eas e or fi nge rprint: Us e oil -fr ee co tto n cloth or paper so ake d wit h alc oho l
or detergent to wipe f rom t he le ns ce nte r outward. Chan ge th e clo th an d wip e several
times if it is n ot cl ean e nou gh.
Warning
This camer a sho uld b e ins tal led by quali fie d per son nel o nly.
All the exam ina tio n and r epa ir work shou ld be d one b y qua lif ied personnel .
Any unauth ori zed c han ges o r modifica tio ns co uld v oid t he warranty.
Statement
.
This guide is for reference only.
Product, manuals and specifications may be mo dif ied w ith out p rio r not ice . Spe co
Tech nol ogi es re ser ves t he ri ght t o mod ify t hes e wit hou t not ice a nd wi tho ut in cur rin g
any obligation.
Speco Technologies is not liable for any loss caused by improper operation.
Note:
Before installation, check the pack age a nd ma ke su re th at al l com pon ent s are i ncl ude d.
Contact your rep or Speco customer service depa rtm ent i mme dia tel y if so met hin g is
broken or missing in the package.
Package
1
Camera
Quick start guide
CD
7 Plastic screw anchors
Drill Template
3 Screws
(PM 4 10mm)×
Overview
Overview
2
3
1
2
3
4
7 (PA 4Screws ×25mm)
1 (PWM3 5mm)Screw ×
4 Rubber o-rings
for screws
1
Fixed ring
Mounting base
Ethernet connector
Audio input
Junction box
Rubber plug
3
4
5
2
6
7
DC power connector
5
6
Micro SD card slot
7
Reset
r
necto
n
o
roo f c
p
-
ter
Wa
External micro pho ne
DC12V
* 1 It is recom mend ed to install th e water- proof conne ctor fo r outdoor inst alla tion s.
* 2 DC 12V pow er su ppl y is no t require d if a Po E swi tch o r injector is us ed to p owe r
the camera.
► Connecting Network Cable
1
2
3
① Loosen th e nut from th e main element.
② Run the net work cabl e (without RJ 45 connector) through both
element s. Then crimp the cable with RJ 45 connector.
③ Connect t he cable to the water-proof connec tor. Then t ighten th e
nut and the m ain cover.
Installation
3
* Befor e you start, p lease make s ure tha t the w all or ce iling is str ong enough
to with stand thre e times the we ight of t he ca mera.
① Open the mo unting ba se and the upper cover of the junction box.
Mount ing Base
Upper C over
② Attach the drill template of the juncti on box to the p lace wher e you
want to ins tall the ju nction box and then drill the screw hole and cable
hole on the w all accor ding to the drill template.
③ Install j unction b ox onto the wall by using the screws provided.
PA 4×
4×
25m m
Rub ber o-r ing
④
Mount the r ubber plu g to the gap of the mounting base and fasten
the camer a onto the mo unting base.
Rubbe r plug
⑤
ns tall the ca me ra onto the j un ctionCo nnect the c ab les and the n i
bo x as shown be lo w.
3×
PM 4 10 mm×
⑥ Br acket Adju stment-Lo osen the fixe d ring to adjus t the view
an gle of the ca me ra. After yo u get the optim um a ngle of vie w,
ti ghten the f ix ed ring to co mp lete the in st allatio n.
Pan 360 °
Tilt 90 °
Fixed R ing
Web Operation and Login
4
IP Scanner can search for the devi ce on the local network.
● Operation
① Make sure that the camera and the PC are connected to the same
local network. The camera is set to DHCP by default.
② Install IP Scanner from the CD and r un it after installation.
Or download from https://www.specotec h.com/ip-scanner/
O4VB 2M
③ In the device list, you can view the IP address, model number, and
MAC addre ss of each de vice. Sel ect the applicable device and double
click to open up the web viewer. You can also manually ent er the IP
address i n the addre ss bar of the w eb browse r.
5C:F 2:07: 24:28 :6A
The login i nterfac e is shown above. Default user name is admin a nd
passw ord is 1234. Afte r l ogg ing in , f oll ow dir ect io ns to in stall
applica ble plugi ns if prompted.
Loading...