Speco O3VFDM Quick Start Manual

Quick Start Guide

3MP VF Motorized Dome IP Camera

O3VFDM

Version 1.0.0

i

Welcome

Thank you for purchasing this Network camera!
This manual is designed to be a reference tool for your system.
Please read this manual carefully before operating the unit and retain it for future reference.
Should you require any technical assistance, please contact Speco Technologies Technical Support.

ii

Important Safeguards and Warnings

1．．．．Electrical safety

All installation and operation here should conform to local electrical safety codes.
Use a certified/listed 12VDC Class 2 power supply only.

Please note: Do not connect two power supplying sources to the device at the same time; it may
result in device damage! The product must be grounded to reduce the risk of electric shock.

Improper handling and/or installation could run the risk of fire or electrical shock.

2．．．．Environment

Heavy stress, violent vibration or exposure to water is not allowed during transportation, storage
and installation.
This product should be installed in a cool, dry place away from direct sunlight and heat sources.
Do not install the product in extreme temperature conditions.
Do not expose the camera to electromagnetic radiation. Otherwise it may result in CMOS sensor
failure.
Do not block any ventilation openings.
Do not allow water and liquid intrusion into the camera.

3. Operation and Daily Maintenance

Please shut down the device and then unplug the power cable before you begin any maintenance
work.
Do not touch the CMOS sensor optic component. You can use a blower to clean the dust on the
lens surface.
Always use the dry soft cloth to clean the device. If there is too much dust, use a cloth dampened
with a small quantity of neutral detergent. Finally use the dry cloth to clean the device.
Please use a professional optical cleaning method to clean the enclosure. Improper enclosure
cleaning (such as using cloth) may result in poor IR functionality and/or IR reflection.
The grounding holes of the product are recommended to be grounded to further enhance the
reliability of the camera.
Dome cover is an optical device, please don’t touch or wipe cover surface directly during
installation and use, please refer to the following methods if dirt is found:

Stained with dirt

Use oil-free soft brush or hair dryer to remove it gently.

Stained with grease or fingerprint

Use oil-free cotton cloth or paper soaked with alcohol or detergent to wipe from the lens center
outward. Change the cloth and wipe several times if it is not clean enough.

iii

Warning

CD 1

This camera should be installed by qualified personnel only.

All the examination and repair work should be done by qualified personnel.

Any unauthorized changes or modifications could void the warranty.

Statement

This guide is for reference only.
Product, manuals and specifications may be modified without prior notice. Speco Technologies
reserves the right to modify these without notice and without incurring any obligation.
Speco Technologies is not liable for any loss caused by improper operation.

Note:

Before installation, check the package and make sure that all components are included.
Contact your rep or Speco customer service department immediately if something is broken or
missing in the package.

Accessory Name Amount

Network Camera Unit 1

Quick Start Guide 1

Installation Accessories Bag 1

iv

Table of Contents

1 Physical Specifications ........................................................................................................ 1

1.1 Components .............................................................................................................................................. 1

1.2 Dimensions ................................................................................................................................................ 2

2 Device Installation .............................................................................................................. 3

2.1 Installation Steps ....................................................................................................................................... 3

3 IP Scanner ........................................................................................................................... 7

3.1

Overview ................................................................................................................................................... 7

3.2

Operation .................................................................................................................................................. 7

4 Web Operation ................................................................................................................... 8

4.1

Login and Main Interface .......................................................................................................................... 8

1

1 Physical Specifications

1.1 Components

Note:
The following figure is for reference only, which is used to indicate the components and the
functions.
Refer to the following figure for component structure. See Figure 1-1.

Figure 1-1 Component structure

Please refer to the following table for detailed information.

Port Port Name Note

Port 1 Ethernet port Network data in/out and PoE

Port 2 DC power jack Connect to DC 12V power, input power

2

1.2 Dimensions

Please refer to the following figure for dimension information. The unit is in mm. See Figure1-2.

Figure 1-2 Dimensions

3

2 Device Installation

2.1 Installation Steps

Note:

 Before installation, please make sure the installation surface can support a minimum of 3

times the weight of the camera

 Please cut off the device power and turn off the device before installing Micro SD card.

Step 1

Use inner hex wrench in the accessories bag to open dome enclosure by unfastening three inner
hex screws on the enclosure.

Figure 2-1 Motorized Varifocal Camera

4

Figure 2-2

Note:



Press the “Reset” button shown in Figure 2-2 for 10 seconds when the device is powered on
if the device needs to be restored to factory default setting.

1. Find the micro SD card slot and open slot according to the direction shown in Figure 2-3.

2. Adjust the direction of the micro SD card and install it into the slot.

3. Close the card slot and lock it firmly.

Step 2

1. Put installation template on the designated surface where you will install the device (wall or
ceiling).

2. Drill holes according to position of the holes on the installation template and then insert the
expansion bolts in the holes. Secure these three bolts firmly.

3.

Adjust the device installation pedestal to the proper position and then pull cable through the
exit hole on Installation surface. Make direction of TOP sign same as it is on the installation
template. Line up the three screw holes in the device pedestal to the three plastic expansion
bolt holes in the installation position. Put the three self-tapping screws in the three plastic
expansion bolts firmly. Fix dome body on installation

Figure 2-3

surface.

5

Note:
 If user pulls out cable from top of installation surface, you must dig an exit hole on

installation surface according to the installation template.

 If user pulls out cable from side of cable channel, it must go through the U-shape channel on

dome pedestal, and take out cable from the side exit hole on pedestal.

Step 3

Adjust device monitoring direction, which is shown in Figure 2-4.

Figure 2-4
Hold both sides of the rotation bracket bottom with hands, rotate horizontally along the axis, and
adjust lens horizontal direction to designated position. Hold the LED decoration cover with hand,
rotate along the vertical direction, adjust the lens vertical direction to designated position; it is
okay to loosen the fix screws on both sides of the bracket first if it is too tight to adjust (just make
it loose, do not take it out), then adjust the lens, tighten the fix screws after adjustment. Hold the
LED decoration cover with hands, rotate horizontally along the axis, and adjust the lens image to
designated position. Range of lens: vertical (0°～+64°), horizontal (0°～+355°), image rotation
direction (0°～+355°).

Note:

The motorized vari-focal series are equipped with motorized vari-focal lens by default, which
needs no manual adjustment.

Step 4

Take up the dome enclosure, put it back on the camera properly regarding to screw and hole, and
fasten the three inner hex screws with wrench.

Note:

Make sure the dome enclosure is secured tightly.

Step 5

Waterproof connector installation for network port; see Figure 2-5 for more details.

6

Figure 2-5

1. Keep the convex groove outward and install the rubber ring into the network port, keep the

smaller hole of the rubber ring outward and install the fixing rubber ring into the main body of
the waterproof connector.

2. Pull the network cable without crystal head through main body of waterproof connector,

fixing rubber ring and waterproof locking cover, make the crystal head of network cable, and
then insert it into the network cable.

3. Put the main body of waterproof connector on the network port and rotate it clockwise to

lock the network port and waterproof connector firmly.

4. Put the waterproof locking cover on the main body of waterproof connector and rotate it

clockwise to lock the waterproof connector and waterproof locking cover firmly.

3 IP Scanner

IP Scanner can search for the device on the local network.

Please note that only devices that are on the same subnet can be discovered.

In the device list, you can view the IP address, model number, and MAC add

Select the applicable device and double click to open up the web viewer.

ress of each device.

3.1 Overview

3.2 Operation

Open up IP Scanner.
Figure 3-1

Figure 3-1 IP Scanner

4 Web Operation

This device supports viewing and management via a web browser on a PC.

Login and Main Interface

Open the browser and input network camera address in the address bar or double click the

Figure 4

The login interface is shown as below. See

Please input your user name and password.

and password is

Note: For security purposes, please change the password after initial login.

After logging in, follow direction

add

ress here

4.1

device in IP Scanner. See

- 1.

Input your IP

Default user name is

admin

Figure 4- 1 IP address

Figure 4- 2.

s to install applicable plugins.

1234

.

Figure 4- 2 Web login