Speco O2VLB2 Owner's Manual

Owner’s Manual

Full HD IP Bullet Camera

O2VLB2

Version 1.0

i

Welcome

Thank you for purchasing this network camera!

This owner’s manual is designed to be a reference tool for your system.

Please read this manual carefully before operating the unit and retain it for future reference.

Should you require any technical assistance, please contact Speco Technologies Technical Support.

ii

Important Safeguards and Warnings

1

．．．．

Electrical safety

All installation and operation here should conform to local electrical safety codes.

Use a certified/listed 12VDC Class 2 power supply only.

Please note: Do not connect two power supplying sources to the device at the same time; it may result in

device damage! The product must be grounded to reduce the risk of electric shock.

Improper handling and/or installation could run the risk of fire or electrical shock.

2

．．．．

Transportation security

Heavy stress, violent vibration or exposure to water is not allowed during transportation, storage and

installation.

3

．．．．

Installation

Do not apply power to the camera before completing installation.

Please install the proper power cut-off device during the installation connection.

Always follow the instructions in this guide.

4

．．．．

Qualified personnel

This camera should be installed by qualified personnel only.

All the examination and repair work should be done by qualified personnel.

Any unauthorized changes or modifications could void the warranty.

5

．．．．

Environment

This product should be installed in a cool, dry place away from direct sunlight and heat sources.

Do not install the product in extreme temperature conditions.

Do not expose the camera to electromagnetic radiation. Otherwise it may result in CMOS sensor failure.

Do not block any ventilation openings.

Do not allow water and liquid intrusion into the camera.

6. Maintenance

Please shut down the device and then unplug the power cable before you begin any maintenance work.

Do not touch the CMOS sensor optic component. You can use a blower to clean the dust on the lens surface.

Always use the dry soft cloth to clean the device. If there is too much dust, use a cloth dampened with a small

quantity of neutral detergent. Finally use the dry cloth to clean the device.

Please use a professional optical cleaning method to clean the enclosure. Improper enclosure cleaning (such as

using cloth) may result in poor IR functionality and/or IR reflection.

iii

7. Accessories

Before installation, please open the package and check that all the components are included.

Contact your distributor immediately if something is broken/missing in your package.

Accessory Name Amount

Network Camera Unit 1

Quick Start Guide 1

Installation Accessories Bag 1

CD 1

iv

Table of Contents

1 General Introduction ................................................................................................................ 1

1.1

Overview .................................................................................................................... 1

1.2

Specifications .............................................................................................................. 1

1.2.1 Performance ........................................................................................................ 1

2 Physical Specifications .............................................................................................................. 2

2.1

Cable .......................................................................................................................... 2

2.2

Dimensions ................................................................................................................. 3

3 Device Installation .................................................................................................................... 5

4 IP Scanner ................................................................................................................................ 7

4.1

Overview .................................................................................................................... 7

4.2

Operation ................................................................................................................... 7

5 Web Operation......................................................................................................................... 8

5.1

Login and Main Interface ............................................................................................ 8

6 FAQ .......................................................................................................................................... 9

Appendix Toxic or Hazardous Materials or Elements ..................................................................... 10

1

Manual/Auto/Low noise/Low motion blur

Supported

Main stream

: 1920x

1080

/ 1280x720

@30fps

VBR/CBR supported

Power

Operating

1 General Introduction

1.1 Overview

This Speco device is a multi-codec (H.264, MJPEG) IP camera that integrates the traditional camera and network

video technology. It enables real time transmission of synchronized video of full HD resolution.

Built-in IR LEDs allows for a suitable image in low light environments. IP66 compliant housing allows for

outdoor installations. Built-in PoE (power over Ethernet) reduces wiring that’s required during installation.

1.2 Specifications

1.2.1 Performance

Camera

Image Sensor Progressive scan 1/3-inch CMOS
Day/Night Mode IR-cut filter
Gain Control Fixed/Auto
White Balance Manual/Auto
BLC On/Off

Electronic Shutter

Video Compression H.264/H.264B/H.264H/MJPEG

Resolutions

Video Bit Rate

Video Flip Mirror and flip
Privacy Mask Supports max 4 privacy mask zones
Video Information Channel title, time title, motion detection, tampering.
Lens 3.6mm fixed
Ethernet 10/100 Base-T

Network

Network Protocol

User Access Max 20 users

Security User ID & password protection, IP address filtering, HTTPS, user access log

Operation & Unit

IR Range 65’ (depending on scene reflection)
Power PoE (802.3af), 12VDC

Consumption

Range: 1/3 to 1/100000.

Sub stream: 704x576 / 704x480 @ 30fps

H.264H: 16Kbps-8192Kbps
MJPEG: adjustable

HTTP，TCP，ARP，RTSP，RTP，UDP，RTCP，SMTP，FTP，DHCP，DNS
DDNS，PPPOE，IPv4/v6，QoS，UPnP，NTP，HTTPS，Bonjour

6W max

，

Temperature
Operating Humidity ≤95%

Dimensions 2.6” (diam) x 6.1” (L)
Unit Weight 1.4 lbs.

-22F ~ 140F

2

2 Physical Specifications

2.1 Cable

Refer to the following figure for cable information.

Figure 2-1 Cable

Please refer to the following sheet for detailed information.

No. Port Name Function Connection Note

1 LAN Network port Ethernet port Connect to standard Ethernet cable for power and data

2 DC 12V Power input port DC jack Power port. Input DC 12V.

3

2.2 Dimensions

Please refer to the following figure for dimension information. The unit is in mm. See Figure 2-3 to Figure 2-6.

Figure 2-3

Figure 2-4

4

Figure 2-5

Figure 2-6

5

3 Device Installation

Important

Please make sure the installation surface can support a minimum of 3 times the weight of the camera.

Figure 3-1 Device installation 1

Please see Figure 3-1 and Figure 3-2.

Step 1

Put installation template on the designated surface where you will install the device (wall or ceiling).

Step 2

Drill holes according to position of the holes on the installation template.

Step 3

Open accessories bag, take out the expansion bolts and insert them into the drilled holes.

Step 4

Take out the screws. Tighten the 4 screws to fix the device on the installation surface (wall or ceiling). The sun

shield can be adjusted. Tighten the screws on the sun shield when finished.

Step 5

Connect all applicable wiring properly.

6

Figure 3-2 Device installation 2

Step 6

Use Philip’s head screw (in accessories bag) to loosen adjusting screw.

Step 7

Adjust the device to point to the desired angle.

Step 8

Use Philip’s head screw to tighten the screws.

4 IP Scanner

for the device on the local network.

that only devices that are on the same subnet can be discovered

IP add

applicable device and double click to open up the web viewer.

of each device

4.1 Overview

IP Scanner can search

Please note

4.2 Operation

Open up IP Scanner.

Figure 4-1

In the device list, you can view the

.

ress, model number, and MAC address

. Select the

Figure 4-1 IP Scanner

5 Web Operation

and management via

Login and Main Interface

and input network camera address in the address bar

The login interface is shown as below. See

Please input your user name and password.

and password is

, please

logging in, follow directions to install applicable plugins

or double click the device in IP Scanner

address

here

This device supports viewing

5.1

Open the browser

See Figure 5- 1.

a web browser on a PC.

Input your IP

.

Default user name is

Note: For security purposes

admin

Figure 5- 1 IP address

Figure 5- 2.

1234

.

change the password after initial login.

Figure 5- 2 Web login

After

.

9

6 FAQ

Bug

Water leakage has
occurred.

IR video is poor.

Cannot log in to the
web viewer.

Settings updates After modifying important camera settings, please reboot the device to



Removal of the front or rear cap may result in water leakage.



The glass front cap has sustained heavy push or strike.



The waterproof plug of the rear cap has loosened.



If there is not enough power, the IR LEDs may not function properly.



The object is out of the IR distance range of current device.



The Active X control is blocked.



The graphics card version needs to be dx8.1 or higher.



Network connection error has occurred.



Invalid network setup.



Invalid user name or password.

make sure the new settings are applied.

10

Circuit Board

Packing

Appendix Toxic or Hazardous Materials or Elements

Component

Name

Component

Device Case

Wire and Cable

Components

Accessories ○ ○ ○ ○ ○ ○

O: Indicates that the concentration of the hazardous substance in all homogeneous materials in the parts is

below the relevant threshold of the SJ/T11363-2006 standard.

X: Indicates that the concentration of the hazardous substance of at least one of all homogeneous materials in

the parts is above the relevant threshold of the SJ/T11363-2006 standard. During the environmental-friendly

use period (EFUP) period, the toxic or hazardous substance or elements contained in products will not leak or

mutate so that the use of these (substances or elements) will not result in any severe environmental pollution,

any bodily injury or damage to any assets. The consumer is not authorized to process such kind of substances

or elements, please return to the corresponding local authorities to process according to your local government

statutes.

Note

Pb Hg Cd Cr VI PBB PBDE

○ ○ ○ ○ ○ ○

○

○

○ ○ ○ ○ ○ ○

Toxic or Hazardous Materials or Elements

○ ○ ○ ○ ○

○ ○ ○ ○ ○



This user’s manual is for reference only. Slight difference may be found in user interface.



All the designs and software here are subject to change without prior written notice.



All trademarks and registered trademarks mentioned are the properties of their respective

owners.



Please visit our website at specotech.com or contact customer service for more information.