Speco O2PTZ22D5W, O2PTZ34D5W User Manual

OONNSSIIPP OO22PPTTZZ2222DD55WW,, OO22PPTTZZ3344DD55WW UUsseerrs

s

’

GGuuiiddee

Rev.1.6 (June. 2013)

1

ONSIP O2PTZ22D5W O2PTZ34D5W

1.

OONNSSIIPP OO22PPTTZZ2222DD55WW,, OO22PPTTZZ3344DD55WW UUsseerrs

s

’

GGuuiiddee

Rev.1.6 (June. 2013)

2

Date

Rev No.

Description

Sept,1st, 2012

1.0

First manual revision creation.

Nov,5th, 2012

1.3

Updated Specification

Mar.3rd ,2013

1.4

Updated picture

May 24th, 2013

1.5

Text revisions

June, 19th, 2013

1.6

Updated package contents, drawings

Revision History

OONNSSIIPP OO22PPTTZZ2222DD55WW,, OO22PPTTZZ3344DD55WW UUsseerrs

s

’

GGuuiiddee

Rev.1.6 (June. 2013)

3

This Unit should be installed by train

ed personnel.

Immediately stop using when the product emits smoke or abnormal heat.

Never install the product in area exposed to oil or gas.

Never install the product on a ceiling

that cannot hold its weight.

Never touch the power cord with wet hands.

Clean only with dry cloth.

Never use the product in extremely high or low temperature condition.

Never drop, hit, strongly nor vibrate the product.

Never expose the product to direct sunlight or severe ray.

Never touch the front glass of the product.

Warning & Cautions

If you fail to read this information and handle the product incorrectly, faulty or malfunction as well as death or serious injury may occur.

OONNSSIIPP OO22PPTTZZ2222DD55WW,, OO22PPTTZZ3344DD55WW UUsseerrs

s

’

GGuuiiddee

Rev.1.6 (June. 2013)

4

Warning: Death or Serious Injury will occur without following Warning.

Caution : Operational Problem(Faulty & Malfunction) will occur without complying with Caution

Reference : Technical Information for Users

Indications:

OONNSSIIPP OO22PPTTZZ2222DD55WW,, OO22PPTTZZ3344DD55WW UUsseerrs

s

’

GGuuiiddee

Rev.1.6 (June. 2013)

5

Table of Contents

Table of Contents ............................................................................. 5

1. Introduction ................................................................................ 7

1.1. Overview of O2PTZ22D5W, O2PTZ34D5W ............................................... 7

1.2. Specification ........................................................................................... 8

1.2.1. Basic Specification .................................................................................................................... 8

1.3. Application of O2PTZ22D5W, O2PTZ34D5W ............................................ 9

2. Production Description ............................................................... 10

2.1. Package Contents ................................................................................. 10

2.1.1. O2PTZ22D5W(OUTDOOR) .................................................................................................... 10

2.1.2. O2PTZ34D5W(INDOOR) ........................................................................................................ 10

2.2. Preview ................................................................................................ 11

2.3. Physical Description .............................................................................. 12

2.3.1. External View ........................................................................................................................... 12

2.3.2. Bottom View & Connection Diagram .................................................................................. 12

2.3.3. External & Internal View ....................................................................................................... 13

2.4. Functional Description .......................................................................... 15

3. Bracket Installation .................................................................. 18

3.1. O2PTZ22D5W(OUTDOOR) .................................................................... 18

3.1.1. Basic Components & Mounting Accessories ...................................................................... 18

3.1.2. Preparation ............................................................................................................................... 18

3.1.3. Installation using Walling Mount Type ................................................................................ 20

3.2 O2PTZ34D5W(INDOOR) ........................................................................ 22

3.2.1. Preparation ............................................................................................................................... 22

3.2.2. Installation using Ceiling Mount Type ................................................................................ 23

3.2.3. Installation using Embedded Mount Type.......................................................................... 24

4. Installation ................................................................................ 27

4.1. Required System Specification .............................................................. 27

OONNSSIIPP OO22PPTTZZ2222DD55WW,, OO22PPTTZZ3344DD55WW UUsseerrs

s

’

GGuuiiddee

Rev.1.6 (June. 2013)

6

4.2. Quick Installation Guide ....................................................................... 28

5. Troubleshooting ......................................................................... 34

5.1. No Video on Viewer .............................................................................. 34

5.2. Windows vista and Windows 7 User for Record & Capture Problem ....... 35

5.3 Technical Inquiry ................................................................................... 38

6. Appendix ................................................................................... 39

6.1. FAN & Heater........................................................................................ 39

6.2. DIP Switch Setting ............................................................................... 40

OONNSSIIPP OO22PPTTZZ2222DD55WW,, OO22PPTTZZ3344DD55WW UUsseerrs

s

’

GGuuiiddee

Rev.1.6 (June. 2013)

7

11..11.. OOvveerrvviieeww ooff OO22PPTTZZ2222DD55WW,, OO22PPTTZZ3344DD55WW

1. Introduction

O2PTZ22D5W(Outdoor), O2PTZ34D5W(Indoor), is a state-of-the-art Speed Dome Network Camera based on integrated Embedded Software technologies such as H.264 & MJPEG, G.726 & PCM Video & Audio Compression, Embedded Web Server, Embedded Streaming Server, various Network Protocols, transmits synchronized video and audio data in real time through IP Network as well as supports bi-directional audio

communication by allowing transmission of audio from Client PC to the camera

O2PTZ22D5W, O2PTZ34D5W is applicable for various sectors such as Security, Remote Monitoring, Remote Education, Simple Video Conference as well as Internet Broadcasting System etc.

OONNSSIIPP OO22PPTTZZ2222DD55WW,, OO22PPTTZZ3344DD55WW UUsseerrs

s

’

GGuuiiddee

Rev.1.6 (June. 2013)

8

11..22.. SSppeecciiffiiccaattiioonn

11..22..11.. BBaassiicc SSppeecciiffiiccaattiioonn

Class

Description

Video

Compression

H.264 / MJPEG

Resolution

**Refer to the datasheet

Audio

(Bi-directional)

Up Stream

32 Kbps G.726

Down Stream

64 Kbps PCM

Network Interface

RJ-45, 10/100 Mbps

Access Network

Static, DHCP, PPP/PPPoE

Protocol

IPv4/6, TCP, UDP, IGMP, ICMP, ICMPv6 etc.

I/O

Sensor 4 NC, NO Selectable

Relay Output

2

Alarm or Remote ON/OFF Control (24V, 1A)

RS-232C

Factory Default

Mic/Line In

Selectable on Admin Page

Line Out

1 V p-p Audio Output for Amp embedded Speaker

CVBS Output

Supported

Power

PoE

Supported

DC In

12VDC Adapter (higher than 2 Amp)

Housing

Water-Proof

IP66

Heater

Refer to Installation Configuration

Installation Type

Bracket

Wall, Ceiling, Ceiling Embedded Type

Motion Detection

3 Regions

Optional Shape & Sensitivity for 3 Regions

Upgrade

Remote F/W Upgrade via IP Network

Management & Configuration

Remote Management & Configuration using IP Network and Admin Tool Page

Client/Viewer

Web Viewer

Simple Access via Internet explorer

Speco-NVR

VMS Software

Dynamic IP

DDNS support

Free DDNS support through Speco Technologies

Security Management

802.1x authentication, User ID & Password Protection, IP Filtering, Audio per user and Bi-directional audio communication configuration control

Time Configuration Management

Sync to PC

Sync to PC Time

Manual

Manual Configuration

Internet Time Server

Sync to Time Server

DLS

Daylight Savings Configuration

OONNSSIIPP OO22PPTTZZ2222DD55WW,, OO22PPTTZZ3344DD55WW UUsseerrs

s

’

GGuuiiddee

Rev.1.6 (June. 2013)

9

11..33.. AApppplliiccaattiioonn ooff OO22PPTTZZ2222DD55WW,, OO22PPTTZZ3344DD55WW

- Security Surveillance (Building, Stores, Manufacturing Device, Parking Lot, Bank, Public Office & Military etc)

- Remote Monitoring (Hospital, Kindergarten, Traffic Status, Public Area)

- Video Conference, Remote Lecture, Internet Broadcasting

- Climate & Environment Surveillance

OONNSSIIPP OO22PPTTZZ2222DD55WW,, OO22PPTTZZ3344DD55WW UUsseerrs

s

’

GGuuiiddee

Rev.1.6 (June. 2013)

10

22..11.. PPaacckkaaggee CCoonntteennttss

22..11..11.. OO22PPTTZZ2222DD55WW((OOUUTTDDOOOORR))

Contents

Description

Remark

Bracket & Housing

Outdoor Housing, Wall Mount Bracket

Manual

Housing Installation Manual

IP Camera

Camera body

Tools & Accessories

L-Wrench 1EA, Cable Tie 5EA, Terminal Block (2Pin, 5Pin, 6Pin : 1EA), Screw(Ø 3x6 2EA, Ø 4x22 2EA)

CD

Software & Product User Manual

Quick Reference

Quick Installation Guide

22..11..22.. OO22PPTTZZ3344DD55WW((IINNDDOOOORR))

Content

Description

Remark

Bracket

Ceiling Mount Bracket

IP Camera

Camera body

Tools & Accessories

L-Wrench 1EA, Safety Wire 1EA, Cable Tie 5EA, Terminal Block (2Pin, 5Pin, 6Pin : 1EA), Screw(Ø 3x6 2EA, Ø 4x16 5EA)

CD

Software & Product User Manual

Quick Reference

Quick Installation Guide

2. Production Description

Open the package and check if the followings are included;

OONNSSIIPP OO22PPTTZZ2222DD55WW,, OO22PPTTZZ3344DD55WW UUsseerrs

s

’

GGuuiiddee

Rev.1.6 (June. 2013)

11

22..22.. PPrreevviieeww

O2PTZ22D5W(Outdoor)

O2PTZ34D5W(Indoor)

IP-Installer

VMS Software

(Speco-NVR)

Speed Dome Network Camera

IP Assignment Program

PC based Client for

monitoring/storing Video/Audio

transmitted form Product

(Max. 64CH supported@D1)

OONNSSIIPP OO22PPTTZZ2222DD55WW,, OO22PPTTZZ3344DD55WW UUsseerrs

s

’

GGuuiiddee

Rev.1.6 (June. 2013)

12

22..33.. PPhhyyssiiccaall DDeessccrriippttiioonn

22..33..11.. EExxtteerrnnaall VViieeww

22..33..22.. BBoottttoomm VViieeww && CCoonnnneeccttiioonn DDiiaaggrraamm

12VDC

Fig 2-1. External View of O2PTZ22D5W, O2PTZ34D5W

Fig 2-2-1. Terminal Block, LAN & Power Connector

OONNSSIIPP OO22PPTTZZ2222DD55WW,, OO22PPTTZZ3344DD55WW UUsseerrs

s

’

GGuuiiddee

Rev.1.6 (June. 2013)

13

22..33..33.. EExxtteerrnnaall && IInntteerrnnaall VViieeww

Fig 2-2-2. Terminal Block, LAN & Power Connector

Fig 2-3-1. Connector Part

OONNSSIIPP OO22PPTTZZ2222DD55WW,, OO22PPTTZZ3344DD55WW UUsseerrs

s

’

GGuuiiddee

Rev.1.6 (June. 2013)

14

Fig 2-3-2. Connector Part

Fig 2-4. Outdoor Housing

OONNSSIIPP OO22PPTTZZ2222DD55WW,, OO22PPTTZZ3344DD55WW UUsseerrs

s

’

GGuuiiddee

Rev.1.6 (June. 2013)

15

22..44.. FFuunnccttiioonnaall DDeessccrriippttiioonn

AC adapter which is compliant to the specification for the camera should be used. Misuse of power supply can cause damage to the unit. Speco assumes no responsibility for misuse of the power supply.

Red/Green LED will be lit with red momentarily and it will be lit with green after a while when power is applied to the camera.

 DC Power

Connect 12 Volt DC adapter to this terminal for supplying power to the network camera.

 MIC/LINE IN

Connect external audio source or microphone.

 Line Out

Connect speakers with built in amplifier. Audio from remote site is output through Line out in bi-directional audio mode.

 100Base-T

100Mbps Ethernet connector (RJ-45). 2 LEDs on the Ethernet connector show the status of the camera

as the following:

- Status LED (Dual Color - Red/Green): It will be lit in green or red depending on the status.  Green: Green color indicates that the camera is in normal operation mode. Continuous green

indicates that data transmission is possible. Blinking green means that someone is connected to the camera

 Red: Continuous or blinking red indicates that hardware is in abnormal condition.

LINK/LAN LED (Orange): It will be lit with orange color when the network cable is connected properly. Blinking orange color indicates that normal data transmission is under way. Off state indicates that there is trouble with the network connection.

OONNSSIIPP OO22PPTTZZ2222DD55WW,, OO22PPTTZZ3344DD55WW UUsseerrs

s

’

GGuuiiddee

Rev.1.6 (June. 2013)

16

Class

Description

Alarm IN

Sensor In (+). NC/NO Selectable in Admin Mode

Alarm IN GND

Ground for Sensor In

Aux OUT

Alarm Output Terminal

Aux OUT(GND)

Ground for Sensor Output

 HEATER/FAN

Used for connecting power cable of heater and fan. Power cable of heater and fan is in the bracket.

 Alarm In/Out (ALARM/AUX)

Used for connecting alarm sensor, alarm annunciation device.

 Aux

Relay output is provided for connecting alarm devices or for remote on/off control of devices such as light. Relay is normal open and it will be closed upon alarm annunciation or remote on.

Fig 2-5. Relay Connection Diagram (Left: lower than 24V, 1A, Right: Higher than 24V 1A)

 Alarm

Connect external alarm sensor. Examples of sensing devices are infrared sensor, motion sensor, heat/smoke sensor, magnetic sensor, etc. Connect the two wires of the sensors to “SNS In”. The sensor type (NC/NO) can be set in admin page. Multiple sensor devices can be connected in parallel.

OONNSSIIPP OO22PPTTZZ2222DD55WW,, OO22PPTTZZ3344DD55WW UUsseerrs

s

’

GGuuiiddee

Rev.1.6 (June. 2013)

17

Sensor Device

Sensor

Power

Supp ly

NO/NCType

Sensor1-

Sensor1+

+12V

GND

Sensor

Device

Sensor

Power

Supp ly

Open CollectorType

Photo Coupler

Fig 2-6. Sensor Input Connection Diagram

OONNSSIIPP OO22PPTTZZ2222DD55WW,, OO22PPTTZZ3344DD55WW UUsseerrs

s

’

GGuuiiddee

Rev.1.6 (June. 2013)

18

33..11..11.. BBaassiicc CCoommppoonneennttss && MMoouunnttiinngg AAcccceessssoorriieess

33..11..22.. PPrreeppaarraattiioonn

3. Bracket Installation

3.1. O2PTZ22D5W(OUTDOOR)

1. Open the Dome Cover by unscrewing with wrench.

OONNSSIIPP OO22PPTTZZ2222DD55WW,, OO22PPTTZZ3344DD55WW UUsseerrs

s

’

GGuuiiddee

Rev.1.6 (June. 2013)

19

- When using system controller for the control of the dome, always set the RS-485 communication channel to be: 2400 bps, 8 bit, 1 stop bit, no parity.

2. Configure the DIP Switch by referring Appendix.

3. Place the Dome Cover and screw.

OONNSSIIPP OO22PPTTZZ2222DD55WW,, OO22PPTTZZ3344DD55WW UUsseerrs

s

’

GGuuiiddee

Rev.1.6 (June. 2013)

20

33..11..33.. IInnssttaallllaattiioonn uussiinngg WWaalllliinngg MMoouunntt TTyyppee

CABLE GLAND

COMBINED CABLE

The wall should be strong enough to hold 4 times of the weight of the camera (5.3 KG). This means that the wall should withstand weight of 21.2 KGs in the minimum.

1. Pass the combined cable through the inside Cable Gland.

2. Fix the end of Cable Gland on the bottom case and coat the attached line between top & bottom of Cable Gland bottom case with silicone. For the installation at Bottom of Bracket, Gland Cable Installation is not required (refer to the below Fig).

OONNSSIIPP OO22PPTTZZ2222DD55WW,, OO22PPTTZZ3344DD55WW UUsseerrs

s

’

GGuuiiddee

Rev.1.6 (June. 2013)

21

Hidden Cable

Exposed Cable

3. Connect Sun-Visor with Wall Mounting Bracket. (1)

4. After connecting Product and Cable, install the product by inserting Product into internal fixing hole of housing and turning in clockwise. (2)

5. Assemble the Bubble. (3)

OONNSSIIPP OO22PPTTZZ2222DD55WW,, OO22PPTTZZ3344DD55WW UUsseerrs

s

’

GGuuiiddee

Rev.1.6 (June. 2013)

22

33..22..11.. PPrreeppaarraattiioonn

- When using system controller for the control of the dome, always set the RS-485 communication channel to be: 2400 bps, 8 bit, 1 stop bit, no parity.

3.2 O2PTZ34D5W(INDOOR)

1. Open the Dome Cover by unscrewing with wrench.

2. Configure the DIP Switch by referring Appendix.

OONNSSIIPP OO22PPTTZZ2222DD55WW,, OO22PPTTZZ3344DD55WW UUsseerrs

s

’

GGuuiiddee

Rev.1.6 (June. 2013)

23

33..22..22.. IInnssttaallllaattiioonn uussiinngg CCeeiilliinngg MMoouunntt TTyyppee

Ceiling board should be strong enough to hold the weight of approx.. 2Kg.

3. Place the Dome Cover and screw.

OONNSSIIPP OO22PPTTZZ2222DD55WW,, OO22PPTTZZ3344DD55WW UUsseerrs

s

’

GGuuiiddee

Rev.1.6 (June. 2013)

24

33..22..33.. IInnssttaallllaattiioonn uussiinngg EEmmbbeeddddeedd MMoouunntt TTyyppee

1. Prepare 190mm Diameter Hole on the ceiling.

2. Place Safety Wire between suspension and Safety Ire Hole to prevent falling-off.

3. Fold the Lock Lever and insert the bracket into the ceiling hole.

4. Fix the bracket to the ceiling with screws.

OONNSSIIPP OO22PPTTZZ2222DD55WW,, OO22PPTTZZ3344DD55WW UUsseerrs

s

’

GGuuiiddee

Rev.1.6 (June. 2013)

25

Prepare 190mm Diameter Hole on the Ceiling.

Place Safety Wire between suspension and Safety Wire Hole to prevent fallingoff.

Fold the Lock Lever and insert the Bracket into the Ceiling Hole.

Fix the Bracket to the Ceiling with Screws.

5. Insert the Camera into the Mount.

6. Apply screw to fix the Camera.

7. Place the cover to finish the installation.

OONNSSIIPP OO22PPTTZZ2222DD55WW,, OO22PPTTZZ3344DD55WW UUsseerrs

s

’

GGuuiiddee

Rev.1.6 (June. 2013)

26

OONNSSIIPP OO22PPTTZZ2222DD55WW,, OO22PPTTZZ3344DD55WW UUsseerrs

s

’

GGuuiiddee

Rev.1.6 (June. 2013)

27

44..11.. RReeqquuiirreedd SSyysstteemm SSppeecciiffiiccaattiioonn

Class

Recommendation

Remark

CPU

Pentium-4 3Ghz

RAM

1GB

Graphic Card

Higher than ATI Chip-Set based 64MB

1920x1080 resolution

LAN Card

Higher than 100Mbps

OS

Windows XP

Web Browser

Higher than Internet Explorer 6.0

4. Installation

Required Specification of PC for Camera Configuration & Control.

* * Operating Systems supported: Windows 2000 Professional, Windows XP / Vista / 7

OONNSSIIPP OO22PPTTZZ2222DD55WW,, OO22PPTTZZ3344DD55WW UUsseerrs

s

’

GGuuiiddee

Rev.1.6 (June. 2013)

28

44..22.. QQuuiicckk IInnssttaallllaattiioonn GGuuiiddee

Product

LAN Switch supporting

IEEE802.3at PoE

Product

LAN Switch

AC Adapter

Fig 4-1. LAN Cable Connection Diagram

2. Connect PC and O2PTZ22D5W, O2PTZ34D5W to Network Device (HUB)

I. Prepare a PC which needs to be connected to Network. II. Connect PC with Product as in Fig 4-1.

3. Install Speco-NVR

Speco-NVR is a multi-channel VMS program for to IP camera or Video server. Install Speco-NVR on remote PC to connect to these products. It is needed to assign connection information to Speco-NVR program before connection. Insert the CD provided with product into the PC and install the Speco-NVR.

OONNSSIIPP OO22PPTTZZ2222DD55WW,, OO22PPTTZZ3344DD55WW UUsseerrs

s

’

GGuuiiddee

Rev.1.6 (June. 2013)

29

Admin Page Button

IP installer

Figure 4-2. Speco-NVR

Follow the sequence below for setting the IP parameter i) Run IP installer ii) Click (1) in ONSIP installer window.> Double click on (2) > Fill in (4) > make a selection in (5) > Fill the

parameters in (6)

iii) Click on (9) to apply the settings. iv) You can connect to admin page by clicking on (10).

OONNSSIIPP OO22PPTTZZ2222DD55WW,, OO22PPTTZZ3344DD55WW UUsseerrs

s

’

GGuuiiddee

Rev.1.6 (June. 2013)

30

Click on the field in (3) for sorting and rearranging the list.

Select network mode that best suits from the drop down list in (5). You can choose either Static or ADSL and Auto (DHCP), respectively. If ADSL and Auto are selected, the fields in (6) are deactivated. In case of ADSL, fill the User Name and Password in (8) with the values provided by your ISP.

If DDNS service is needed, Check at the box and fill the empty field with hostname you want in

⑦

.

1 2 3 6 4

9 5 7

8

10

OONNSSIIPP OO22PPTTZZ2222DD55WW,, OO22PPTTZZ3344DD55WW UUsseerrs

s

’

GGuuiiddee

Rev.1.6 (June. 2013)

31

For the use of Web Viewer, Active-X module should be installed. If internet access is available, you can download it by accessing Camera or if you install Speco-NVR, Active-X module will be installed together.

Connection to Admin Page

Basic Control Buttons

Video Crop Control

4. Remote Connection to Camera

I. Connection via Web Viewer

Web View is the simplest method to connect to the product via internet explorer. Once you insert ”http://IP_address:HTTP_port_number” into Internet Explorer, you can access the page.

Fig 4-3. Web Viewer Connection

Basic ID / Password of Admin Tool: admin /1234 For the detail, please refer to [Configuration_Guide].

OONNSSIIPP OO22PPTTZZ2222DD55WW,, OO22PPTTZZ3344DD55WW UUsseerrs

s

’

GGuuiiddee

Rev.1.6 (June. 2013)

32

Camera Assignment

Live view

Save

Example

Exit Program

Default ID/PW: admin/1234

1) Connection through Speco-NVR Click the camera assignment button for setting camera address. Input the description, address, Ch#, User ID, Password and port and then click the save button. After assignment procedure, you must click the SAVE button. You can see the live video when you click the live view button as below. When you exit Speco-NVR, you have to input the ID/PW, admin/1234. Details for the Speco-NVR can be found in [Speco-NVR User’s Guide].

Figure 4-4. Speco-NVR

OONNSSIIPP OO22PPTTZZ2222DD55WW,, OO22PPTTZZ3344DD55WW UUsseerrs

s

’

GGuuiiddee

Rev.1.6 (June. 2013)

33

4. Initial Configuration by connecting Admin Mode

All Parameters of O2PTZ22D5W are initially set as factory default. So you must change them with appropriate value to your network configuration by accessing via Admin Tool. Admin Tool Access Method is as below.

Http://[IP Address]:[HTTP Port No.]/ admin.htm

Admin Tool Access ID / Password: admin / 1234. As it is Default Value, please change them. For the detailed

Configuration, please refer to [Configuration_Guide].

OONNSSIIPP OO22PPTTZZ2222DD55WW,, OO22PPTTZZ3344DD55WW UUsseerrs

s

’

GGuuiiddee

Rev.1.6 (June. 2013)

34

55..11.. NNoo VViiddeeoo oonn VViieewweerr

1

2

5. Troubleshooting

 Network Connection Status Check(Ping Test)

You can check the Network Connection Status by doing Ping Test.

- Start > Run > cmd > Ping IP Address (EX>ping 172.16.42.51).

- If you get the response such as “Reply from~”, Network Configuration & Connection Status is good.

Please re-try to access or refer to other trouble shooting category. ( ).

- If you get the response such as “Request timed out”, Network Configuration & Connection Status is in

problem. Please check the Network Cable and Configuration. ( )

OONNSSIIPP OO22PPTTZZ2222DD55WW,, OO22PPTTZZ3344DD55WW UUsseerrs

s

’

GGuuiiddee

Rev.1.6 (June. 2013)

35

55..22.. WWiinnddoowwss vviissttaa aanndd WWiinnddoowwss 77 UUsseerr ffoorr RReeccoorrdd && CCaappttuurree PPrroobblleemm

For the use of Video Recording & Capture function on Speco-NVR and Web Viewer, Windows Vista and

Windows 7 Users are required to configure “User Account Configuration” and “Program Execution

Entitlement Configuration”. If not configure, Recorded File won’t be generated or Captured Image on Web Viewer won’t be saved.

Windows Vista Configuration

1. User Account Configuration

1) Select “User Account” on Control Panel

2) Select “Turn User Account Control on or off”

3) Uncheck “Use User Account Control to help protect your computer”.

2. Program Execution Entitlement Configuration

1) Select “NVR” icon on the wallpaper.

2) Select “Properties” menu popped up by clicking right button on Mouse.

3) Select Check Box of “Run this program as an administrator” from the compatibility Tap.

OONNSSIIPP OO22PPTTZZ2222DD55WW,, OO22PPTTZZ3344DD55WW UUsseerrs

s

’

GGuuiiddee

Rev.1.6 (June. 2013)

36

Windows 7 Configuration

1. User Account Configuration

1) Select “User Account” on Control Panel

2) Select “Change User Account Control Setting”

3) Set the Alarm Level at the lowest “Never Notify”

OONNSSIIPP OO22PPTTZZ2222DD55WW,, OO22PPTTZZ3344DD55WW UUsseerrs

s

’

GGuuiiddee

Rev.1.6 (June. 2013)

37

2. Program Execution Entitlement Configuration

1) Select “NVR” icon on the wallpaper

2) Select “Properties” menu popped up by clicking right button on Mouse

3) Select Check Box of “Run this program as an administrator” from the compatibility Tap.

OONNSSIIPP OO22PPTTZZ2222DD55WW,, OO22PPTTZZ3344DD55WW UUsseerrs

s

’

GGuuiiddee

Rev.1.6 (June. 2013)

38

55..33 TTeecchhnniiccaall IInnqquuiirryy

For the quickest solution, please prepare all information below;

1. Product Model Name

2. Serial No. & Mac Address

3. Date of Purchase

4. Summary of Problem

5. Error Message

Please contact to your supplier if you still have problem even taking all trouble shootings.

OONNSSIIPP OO22PPTTZZ2222DD55WW,, OO22PPTTZZ3344DD55WW UUsseerrs

s

’

GGuuiiddee

Rev.1.6 (June. 2013)

39

Speco O2PTZ22D5W, O2PTZ34D5W User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual