Speco HTINTT5H User Manual
HTINTT5H
TM
700Line Intensifier H
Traditional Box type camera
200 New Highway, Amityville, NY 11701
800-645-5516 / www.specotech.com
1. PACKAGE CONTENTS
1 Camera
2 Mounting Screw
1 Mounting Bracket
1 Wrench
2. BACK PANEL CONFIGURATION
BNC OutOSD joystick
Relay OutPower In
4. OSD MENU DETAILS
3. FEATURES
PRESETS
Used for a quick and easy setup for the installation
environment.
700TVL Resolution
Horizontal resolution of 700 TV lines is achieved
by using a SONY Super-HAD CCD with 520,000
pixels, and a custom DSP yielding pictures with
a high S/N ratio.
INTENSIFIER 3
More powerful performance in low light condition.
High quality pictures can be captured in very low
light conditions.
WDR
Allows you to get a clear image even with strong
back-lighting.
SPECO DNR
DSP chip can remove image noise to produce
clean images in low light conditions.
HLC (High Light Compensation)
This function reverses bright spots in the picture
(such as headlights). This enables the entire
system to do a better job of resolving and
displaying grayscale information such as a
license plate.
Motion Detection with Alarm Output
Built in motion detector with adjustable areas
of coverage will send a signal to an external
alarm device when motion is detected.
PRIVACY MASK
Mask up to 8 areas of the picture where
viewing is not desired. Each zone can be
Independently programmed via the OSD
STABILIZER
Removes image jitter that is
caused by vibrations in the surroundings.
DIGITAL ZOOM
Digitally enlarge the picture.
DAY/NIGHT
Can show color pictures in all lighting
conditions or automatically switch to a B/W
picture in low light conditions
OSD
All camera functions are menu driven
for easy use.
1. PRESET
Used for a quick and easy setup for the installation
environment.
2. LENS SETUP
- BRIGHTNESS : Adjusts the video brightness.
- IRIS SPEED : Adjusts Iris control speed of the DC
lens.
- FOCUS ADJ : To adjust the DC lens focus correctly,
you must change MODE to ON under the FOCUS
ADJUST menu. Adjust the lens focus and after the
lens focus had been adjusted, change MODE to OFF.
3. EXPOSURE SETUP
◆◆◆◆
BRIGHTNESS : Adjusts the video brightness.
◆◆◆◆
SHUTTER : You can select auto or manual shutter.
* A.FLK : Select this when you see picture flicker, this
can happen when the frequency of the local lighting
clashes with the camera.
* ESC : Select this to control the shutter speed
automatically. If ESC is selected, the shutter speed is
automatically controlled depending on the ambient
illumination of the subject.
* MANUAL : You can control shutter speed manually.
(1/60 ~ 1/120,000)
* --- : Shutter speed is fixed at 1/60 sec. (1/50 sec.)
◆◆◆◆
AGC (AUTO GAIN CONTROL) : The higher the gain level,
the brighter the screen - but the higher the noise.
* OFF : Deactivates the AGC function.
* LOW : Allows automatic gain control from 5.3dB to 32dB.
* HIGH : Allows automatic gain control from 5.3dB to 37dB.
◆◆◆◆
INTENSIFY : When it is night or dark, the camera
automatically detects the light level and maintains a clear
picture if this mode is activated.
* OFF : Deactivates the INTENSIFY function.
* AUTO : Activates the INTENSIFY function.
4. WDR SETUP
WDR illuminates darker spots of an image while retaining
the same light level for brighter spots to even out the
overall brightness of images with high contrast between
bright and dark spots.
5. WHITE BAL. SETUP
◆◆◆◆
ATW : Select this when the color temperature is
between 1,700˚K and 11,000˚K.
◆◆◆◆
OUTDOOR : Select this when the color temperature is
between 1,700˚K and 11,000˚K. (sodium light
inclusion)
◆◆◆◆
INDOOR : Select this when the color temperature is
between 4,500˚K and 8,500˚K.
◆◆◆◆
MANUAL : Select this to fine-tune White Balance
manually. Set White Balance first by using the
ATW or AWC mode. After that switch to
MANUAL mode, fine-tune the White Balance and
then press the Function Setup switch.
◆◆◆◆
AWC→SET : For optimal luminance level for the current
environment, point the camera towards a sheet
of white paper and press the Function Setup
switch. If the environment changes, readjust it.
6. BACK LIGHT SETUP
◆◆◆◆
USER BLC : Enables a user to select a desired
area on a picture and view that area
more clearly.
◆◆◆◆
HLC (High Light Compensation) : If the scene
contains extremely bright light areas such as
car headlights, the light can mask out much of the
on-screen detail. Use this feature to remove these
exceptionally bright light areas to allow detail
such as car license plate numbers to become
visible.
☞☞☞☞
NOTES
■
Because there can be a difference in the
effectiveness of HLC according to the
amount
of light area in the screen, optimize the installation
angle for the best HLC performance.
■
When dark, HLC is activated in NIGHT ONLY
mode when a bright light exceeds a specific
amount.
■
When in NIGHT ONLY mode, HLC is not activated
in daylight or in nighttime when bright light
is not present
■
BLC Function doesn't work in the B/W mode of the
7. SPECO DNR SETUP
DAY/NIGHT menu.
This function reduces the background noise in a
low luminance environment level.
☞☞☞☞
NOTE
■
When the AGC mode of the EXPOSURE menu is ‘OFF’,
you cannot set the SPECO DNR to ‘ON’ or ‘OFF’.
■
When adjusting the noise reduction level in DNR3 mode,
remember that the higher the level that is set, the greater the
noise level reduction, as is the brightness of the image.
8. DAY/NIGHTSETUP
◆◆◆◆
COLOR : The picture is always displayed in color.
◆◆◆◆
B/W : The picture is always displayed in black and white.
- BURST MODE : You can turn on or off the burst signal on
B/W mode.
◆◆◆◆
AUTO : The mode is switched to 'Color' in a normal
environment, but switches to 'B/W' mode when
ambient illumination is low. To set up the
switching time for AUTO mode, press the
Function Setup switch. You can turn on or off the
burst signal on B/W mode.
- BURST MODE : You can turn on or off the burst signal on
B/W mode.
- DURATION : You can select brightness of illumination
about changing the day/night mode.
- DWELLTIME : You can select the duration time
about changing the day/night mode.
9. SPECIAL SETUP
◆◆◆◆
IMAGE ADJ.
• Monitor
• Reverse
*PIP (Picture in Picture) :Displays a full size image along
with the thumbnail to provide more detailed information.
• D-ZOOM : Digital zoom up to 16x
• Font Color
• Sharpness
• Language
◆◆◆◆
SYNC : In areas where the supply is at 60Hz(NTSC),
50Hz(PAL), you can synchronize the output phase of multiple
cameras using the power synchronization function (Line-Lock)
without using a synchronization signal generator.
- INT : Internal Synchronization Type
-L/L : Power Synchronization Type, Line-lock
◆◆◆◆
MOTION : This camera allows you to observe movement of
objects in 8 different areas on the screen, and the words
'MOTION DETECTED' appear on the screen when movement
is detected.
- MOTION : Enable or disable the motion detection feature.
* DETECTION : Activates motion detection
- DETECT BOX : Outlines an object on the screen in a box when
movement matches a custom motion type.
- ALARM OUT : Trigger the signal from the Alarm Output
Terminal of the camera when an object’s movement matched a
custom motion type.
- DETECT AREA : Defines the motion detection area.
- MASK AREA : Specify a detection exception area to mask.
Select a mask area number and specify the size and position.
* AREA : Select up to 4 areas
* MODE : Turn the selected area ON or OFF.
* TOP/BOTTOM/LEFT/RIGHT : Adjust the size and position of the
selected area.
- SENSITIVITY : Set the sensitivity of the motion detection. The
higher the level, the motion detection sensitivity is increased to
recognize smaller movements.
-DET. SIZE : Selects an object size to detect on the screen. The
higher the level means the larger the detection size.
◆◆◆◆
PRIVACY
- AREA SEL : You can select up to 12 PRIVACY areas.
- MODE : Turn the selected area ON or OFF.
- MASK COLOR : Determine area color. Select GREEN, RED,
BLUE, BLACK, WHITE and GRAY.
- TRANSPARENCY : Add or remove transparency from the
masked area.
-SEL POS : Adjust the size and position of the selected area.
- X POS, - Y POS
5.DIMENSIONS
2.5” W
2.2” H
4” L
6. SPECIFICATION
Image Pick-Up Device 1/3” 960H Sony Super HAD CCD
Total Pixels NTSC=1020(H) * 508(V) / PAL=1020(H) * 596(V)
Effective Pixels NTSC=976(H) * 494(V) / PAL=976(H) * 582(V)
Scanning Frequency
Scanning System 2:1 Interlace
Synchronization Internal
Resolution 700TV Lines
Minimum Illumination 0.15 Lux, 0.00002 Lux (Sens-up)
S/N Ratio More than 52dB
Video Output CVBS: 1.0Vp-p / 75Ω
Electronic
Shutter Speed
WDR On / Off (Level adjustable)
BLC BLC / HLC / OFF
Day & Night Color / BW / AUTO / EXT
Gain Control Low / High / Off
White Balance ATW / Outdoor / Indoor / Manual / AWC (1,700
Intensify Auto / Off (Selectable x2 ~ x512)
Motion Detection On / Off (8 Programmable Zones)
Privacy Masking On / Off (12 Programmable Zones)
SPECO DNR On / Off (Level adjustable)
Power Supply DC 12V / AC24V(Dual Voltage)
Power Consumption DC 12V 260mA / AC24V 240mA
Lens CS Mount Lens Optionally
Operational Temp. -4ºF~140ºF RH 95% Max
Storage Temp. -4ºF~140ºF RH 95% Max
Dimension 2.51"(W) * 2.20"(H) * 3.46"(D)
Weight 1.5 lbs
NTSC=15.734KHz(H) & 59.94Hz(V)
PAL=15.625KHz(H) & 50.00Hz(V)
NTSC=(1/60sec~1/120,000sec)
PAL=(1/50sec~1/120,000sec)
K ~ 11,000
°°°°
K)
°°°°
Speco Technologies is constantly developing product improvements. We reserve the right to modify product
design and specifications without notice and without incurring any obligation.
Rev. 130115
Loading...