Page 1
03/ UV
MODE
SPD/CLR
SV-3T
UP BUTTON
Short single presses toggle through
the three display modes: W.TMP =
Water Temperature, S.TMP = Set
Temperature, TIME = Clock.
Holding the button will force the
controller to begin adjusting the set
temperature and will raise the set
temperature point.
Also used for adjusting settings.
DOWN BUTTON
Short single presses toggle through the three
display modes: W.TMP = Water Temperature,
S.TMP = Set Temperature, TIME = Clock.
Holding the button will force the controller to
begin adjusting the set temperature and will
lower the set temperature point.
Also used for adjusting settings.
LIGHT (ON/OFF) BUTTON
Used to toggle spa lights on/off.
LIGHT (MODE) BUTTON
Press to activate light mode menu &
use up & down buttons to select one
of five different lighting effect modes.
LIGHT SPEED / COLOUR
Press to activate light speed or
user colour selection menus. Use
up & down buttons to adjust.
OK BUTTON
Used to confirm and save setting
adjustments or to enter setting
adjustment menus.
SLEEP TIMER
INDICATOR LED
This LED will turn on
when the controller is
in a sleep mode.
SANITISER INDICATOR LED
This LED will turn on to indicate
that the ozone or uv sanitiser
unit is operating (if fitted).
HEATER INDICATOR LED
This LED will turn on when the
heater or heat pump (if fitted)
is operating.
AUTOMATIC INDICATOR LED
This LED will turn on whenever
the filtration pump is in automatic
mode.
SANITISE BUTTON
Press once to activate
a 20 min sanitisation
and clean up cycle to
refresh water quality
after spa use. A
second press will
cancel the cycle if
already running.
BLOWER BUTTON
Press to toggle blower
on/off. A single press
turns blower on in
vari-speed mode. Use
up & down buttons to
vary speed. A double
press activates the
ramping mode.
PUMP BUTTONS
Used to toggle filtration
pump and / or any
additional jet pump(s)
on / off (if fitted).
INVERT SCREEN
BUTTON
Press to flip screen
o
180 for easy viewing
when spa in use.
POWER SMART
QUICK REFERENCE GUIDE
SA SU MO TU WE TH FR
SET TEMP
SET TEMP
°C
°F
°C
°F
°C
°F
MODE
SPD
BRT
MODE
SPD
BRT
OFF
ON
AM
PM
AM
PM
:
1 0 3 0
3 8.0
MENU ICONS
Sleep timer menu icon
Light menu icon
Blower menu icon
STATUS ICONS
Keypad locked
Sanitise cycle operating
DISPLAY MODE ICONS
Water Temperature
Set Temperature
Clock
Filtration cycle operating
Fault condition has occured
Page 2
QUICK REFERENCE GUIDE
CHANGING LIGHT MODES PARTIAL KEYLOCK [FILT] DAILY FILTRATION TIME OFF P.SAV disabled
LOW Filtration only
Press Light (mode) button to Press and hold this button combination This setting is used to control the hours HIGH Filtration and heating
until LOCK appears on the display: of filtration per day. Filtration limits
display current light mode in use.
differ depending on pump type. Once P.SAV mode is selected the begin
and end times of the PEAK power tariffs
Press or button to step
Circ Pump (2A or less) 1-24 hrs must be set so the control knows NOT
through choice of light modes:
Repeat button combination to unlock. Jet Pump (2spd or 1spd) 1-8 hrs to operate during those hours.
WHTE White Light
Note: Once locked only pumps, blower, BGN Peak power begin time
UCLR User Colour
light and sanitise buttons can be used. [F.CYC] FILTRATION CYCLES END Peak power end time
FADE Fade Effect
Access to all other buttons is disabled.
STEP Step Effect
This setting defines how often filtration
PRTY Party Effect
cycles occur. Filtration can be set to run [W.CLN] AUTOMATIC SANITISE
SETUP MENU every 1/2/3/4/6/8/12 or 24 hrs
CHANGING LIGHT SPEED OR
This setting allows adjustment of the
LIGHT COLOUR
The setup menu allows customisation start time of the 10 minute automatic
of the adjustable controller settings. [SNZE] SLEEP TIMERS daily sanitise cycle. Setting can be
Dependant on light mode selected the
Menu access and item adjustments are adjusted from 0:00 to 23:59.
Light (spd/clr) button will activate
carried out as follows: Used to disable automatic heating and
one of three light mode option screens.
filtration during certain times of day or
Press and hold and buttons night. Upon entering SNZE menu there [D.DIS] DEFAULT DISPLAY MODE
CL:xx User Colour Number
are four choices:
together until [MODE] is displayed.
L.SPD Light Transition Speed
Used to adjust the default display mode
L.BRT Light Brightness
1.SNZ Sleep Timer #1
shown on the keypad. Setting choices:
Press or to navigate through
2.SNZ Sleep Timer #2
Press or button to adjust
R.SET Reset timers to default
setup menu items.
W.TMP Water Temperature
EXIT Exit sleep timer menu
each setting.
S.TMP Set Temperature
TIME Clock
Press to enter item adjustment.
Only one sleep timer needs to be set
Press button to save each setting
however two timers are provided to
and move to the next setting.
Press or to adjust setting.
facilitate different sleep settings on
[T.OUT] LOAD TIME OUTS
different days. Each sleep timer setting
Note: All light settings are saved for
consists of a week day setting, start
Press to confirm setting and exit.
All accessory loads (ie. pumps and/or
future ON / OFF use.
time and stop time (refer below).
blower) automatically turn off after a
All setup menu items follow the same
x.DAY Day(s) of operation
time out period has elapsed. Fifteen
adjustment procedure. Menu items that
x.BGN Sleep timer begin time
(15) minutes later the lights will switch
FULL KEYLOCK
can be adjusted are as follows:
x.END Sleep timer end time
off and the pool will return to automatic
mode. This setting allows the length of
Press and hold this button combination
Use the Up, Down & OK buttons to
the time out period to be adjusted.
until LOCK appears on the display:
[MODE] OPERATING MODES
adjust and confirm each setting.
Setting ranges from: 10 - 60 minutes
Operating modes effect demand
heating and filtration behaviour. The
[P.SAV] POWER SAVE (off peak)
setting choices are:
Repeat button combination to unlock.
Reduce operating costs by limiting
NORM Normal heating & filtration
Note: Once locked if any button is
filtration and heating to occur only
ECON Heating only during filtration
pressed the key stroke will be ignored
during cheaper off peak power periods.
AWAY Heating disabled. Filtration
and the display will show LOCK.
There are three P.SAV modes:
reduced to 1hr p/day
up
down
pump a
+ +
up
down
pump b
+ +
MODE
SPD/CLR
Loading...