Southern Folger LOCK MOUNTINGS User Manual

PARACENTRIC
CYLINDER
AND KEY

APPLICATION:

A complete line of Southern
Steel brand, high-quality deten­tion-type locks is available with
lever tumbler cylinders. The
cylinders are cast bronze and
are operated by paracentric
key. Master keying is not avail­able for locks with paracentric
cylinders.

A C C E S S O R I E S

PARACENTRIC CYLINDER

TECHNICAL DATA:

• CYLINDERS and KEYS
Silicon

• CYLINDER SIZE:
1”

• CYLINDER WEIGHT: .5 lb.

• KEY SIZE:
4-3/4”

• KEY WEIGHT: .2 lb.

• TENSILE STRENGTH:
60,000

• YIELD STRENGTH:
20,000

• ROCKWELL HARDNESS:
73

bronze/copper alloy

Diameter (Nominal)

L x 5/32” TK

p.s.i.

p.s.i.

Minimum HRB

PARACENTRIC KEY

Revised 3/09

FOR MORE INFORMATION, PLEASE CALL 210-533-1231

F1

MOGUL CYLINDER
AND KEY

APPLICATION:

Many of our locks are equipped
with a “mogul-type” cylinder. This
rugged cylinder is approximately
twice the size of a standard
“builder’s hardware” cylinder.
The

mogul cylinder has six-pins
with side bar operation. Six
tumbler
security than standard five
tumbler
combinations
cylinders
same exclusive key, including
Southern Steel security builders
cylinder, if desired.

cylinders provide higher

cylinder with more

available. All

may operate under the

A C C E S S O R I E S

HIGH SECURITY SIX-PIN

MOGUL CYLINDER

NOTE: Master keying available.

TECHNICAL DATA:

• STANDARD FINISH: US26D

• MOGUL CYLINDERS:

Brass

• MOGUL KEYS: Nickel silver

• CYLINDER SIZE: 2” thread

Diameter

• CYLINDER WEIGHT: 1.5 lbs.

• KEY SIZE: 2-3/8” L x 1/8” TK

• TENSILE STRENGTH:

91,000 lbs/in.2

• YIELD STRENGTH:

76,000 lbs/in.2

• ROCKWELL HARDNESS:

89 HRB

• PIN TUMBLERS:

Combination

stainless steel,

and

tumblers per lock

6

nickel silver

MOGUL KEY

F2

Revised 3/09

P.O. BOX 2021 • SAN ANTONIO, TX • 78297 • 210-533-1231 • FAX: [phone]

HINGES

203FS: FULL SURFACE
203FP: FOOD PASS

APPLICATION:

For use on food passes,
observation
small swinging doors where a
medium duty hinge is required.
Available with solid leaves for
welded application or pre-drilled
for fasteners. The 203FP is a
version of the 203FS with a
built-in
door in a horizontal position for
use as a shelf.

shutters and other

stop to hold the food pass

A C C E S S O R I E S

203FS FULL SURFACE HINGE

TECHNICAL DATA:

• HINGE LEAVES: Steel

• HINGE PIN: Cold-rolled steel

• SIZE: 3” H x 2-3/4” W x 1/4” TK

• WEIGHT: .9 lb.

• PIN SIZE: 1/2” diameter

• 203FS: No holes standard

• 203FP: Drilled and countersunk
for

screws standard

203FP F00D PASS HINGE

Revised 3/09

FOR MORE INFORMATION, PLEASE CALL 210-533-1231

F3

INSTITUTIONAL
HINGES

204FMSS
INSTITUTIONAL

APPLICATION:

For swinging hollow metal doors.
Each hinge features cast
stainless
integral
non-removable
pin. Security fasteners are
provided

steel leaves with

security stud and

with each unit.

HINGES

stainless steel

A C C E S S O R I E S

204FMSS FULL MORTISE HINGE

TECHNICAL DATA:

• STANDARD FINISH:
Stainless steel - US32D

• SIZE: 4-1/2" x 4-1/2" x 3/ 16"

• WEIGHT: 1.5 lbs.

• HINGE LEAVES:
Cast stainless ste el

• HINGE PIN: Stainless steel

• ASTM F1758 Certified
Impact Test-Grade 1

F4

Revised 3/09

P.O. BOX 2021 • SAN ANTONIO, TX • 78297 • 210-533-1231 • FAX: [phone]

205 HINGE

SF 205FS: FULL SURFACE HINGE
SF 205G: GAP HINGE

APPLICATION

Swinging doors at cells, corridors,
plumbing chases, gates or other
locations where a higher degree of
security is required. Available in full
surface or gap type configuration.

A C C E S S O R I E S

SOUTHERN FOLGER 205 HINGE

Leaf configuration can be any
combination of solid leaf for weld-on or
pre-drilled leaf for bolt-on.

Continuous non-removable hardened
steel alloy pin. Smooth operating radial
and thrust polymer bearings.

TECHNICAL DATA

Size: 5"H x 4-1/2" W x 1/2" TK (FS)

5"H x 6" W x 1/2" TK (GAP)
Weight: 5 lbs.
Pin Size: 5/8" diameter.
Barrel Size: 1-1/2" diameter.
Barrels/Leaves: Cold rolled steel.
Finish: USP.

Exceeds all criteria for ASTM F1758 for
detention hinges for Double Weight
Grade 1.

Made in USA.

SF 205G:

GAP HINGE

SF 205FS:

FULL SURFACE HINGE

Weight capacity 800 pounds per weld-on
hinge.

NOTE: These hinges are not direct
replacements for the Folger Adam #5
Hinge or the Southern Steel 205 Hinge
due to barrel size difference.

Revised 12/11

TO ORDER, PLEASE CALL 210-533-1231

SF7

INSTITUTIONAL
HINGES

APPLICATION:

Designed to supply power from
door

frames to electric locks on
hollow metal doors, the 204E
Power Transfer Hinge contains
five completely concealed and
tamperproof Teflon
conductors.
mortise configuration only to be
used with three 204FMSS
institutional hinges. This is not a
load-bearing

Available in full

hinge.

™

-coated

A C C E S S O R I E S

204E ELECTRIC POWER

TRANSFER HINGE

TECHNICAL DATA:

• STANDARD FINISH: US26D

• SIZE:

• WEIGHT: 1.6 lbs.

• HINGE LEAVES: Investment

cast

• HINGE PIN: 5/8” diameter

O.D.

• ELECTRICAL: 1 amp

capacity, 40 volts maximum

4-1/2” x 4-1/2” x 3/16”

brass

tubing steel

Revised 12/10

FOR MORE INFORMATION, PLEASE CALL 210-533-1231

F5

DOOR PULLS

APPLICATION:

Economical, attractive, general
purpose
ease of operation on heavy
doors and/or heavy traffic
areas. Provided with
security

door pulls designed for

fasteners.

A C C E S S O R I E S

212C

RAISED DOOR PULL

TECHNICAL DATA:

• FINISH:
US26D

• MATERIAL:
Cast

brass

• SIZE:
8 -11/16”
Projection

• WEIGHT: 1.3 lbs.

L x 1-3/4” W x 2-3/8”

Revised 3/09

FOR MORE INFORMATION, PLEASE CALL 210-533-1231

F7

DOOR PULLS

214S RECESSED DOOR PULL

APPLICATION:

The 214 is of adequate size for
easily manipulating large,
heavy doors. Often used on
inmate side of doors. Provided
with security fasteners.

A C C E S S O R I E S

214S RECESSED DOOR PULL

TECHNICAL DATA:

• FINISH:
US26D

• MATERIAL: Cast brass

• SIZE: 5” H x 4” W x 1” D

• WEIGHT: 1.5 lbs.

215C KNOB PULL

APPLICATION:

An attractive, brass knob
pull for light traffic areas where
a fixed knob is required.
Provided with security fasteners.

TECHNICAL DATA:

• FINISH:
US26D

• MATERIAL: Brass

• SIZE: 2-1/4” DIA Knob x

2-1/4”
3-1/4”

• WEIGHT: .5 lb.

Projection x

DIA Base

215C KNOB PULL

F8

Revised 3/09

P.O. BOX 2021 • SAN ANTONIO, TX • 78297 • 210-533-1231 • FAX: [phone]

ESCUTCHEON AND
CYLINDER SHIELD

218 ESCUTCHEON

218-1 ESCUTCHEON: ONE WAY
218-2 ESCUTCHEON: TWO WAY

APPLICATION:

The 218 Escutcheon is used to provide a
close fit between a paracentric cylinder
and the keyhole. It also serves to protect
the finish around the keyhole from chipping.
The one-way escutcheon prevents the key
from being extracted from the cylinder while
lock is in the unlocked condition. Provided
with security fasteners.

A C C E S S O R I E S

ESCUTCHEON

TECHNICAL DATA:

• FINISH:

• MATERIAL: Stainless steel,

• SIZE: 3" DIA x .105" TK

• WEIGHT: .2 lb.

US32D

219 CYLINDER SHIELD APPLICATION:

The 219 Cylinder Shield mounts over the
paracentric cylinder on exterior doors to
protect the keyhole from dirt, snow and
other foreign elements. Provided with
security fasteners.

TECHNICAL DATA:

• FINISH: US26D

• MATERIAL: Stainless Steel

• WEIGHT: .5 lb.

219M MOGUL CYLINDER SHIELD

Same as above except shield mounts
over the mogul cylinder. US26D finish.

218-2 shown

CYLINDER SHIELD

Revised 9/13

219 shown

FOR MORE INFORMATION, PLEASE CALL 210-533-1231

F9

DOOR POSITION
SWITCHES FOR
SWINGING DOORS

200MRS MAGNETIC SWITCH
APPLICATION:

The 200MRS is used where a built-in
door indicator switch is desired. This
tamper-proof unit is mortised into the
door frame. An actuating magnet is
recessed into the door edge.
Provided with security fasteners.

TECHNICAL DATA:

• SIZE: 4-7/8” L x 1-1/4” W

• WEIGHT: 1 lb.

• ELECTRICAL: 24 volts (AC or DC)

200MRS TB MAGNETIC SWITCH

Triple Bias Switch

A C C E S S O R I E S

200MRS MAGNETIC

SWITCH

200MRS shown

220A DOOR POSITION SWITCH
APPLICATION:

The 220A switch actuates a remote
lamp indicator or an audible signaling
device the moment a swinging door is
moved from the fully-closed position.
Enclosed in a 10 gauge galvanized
steel housing, the 220A is designed
for installation on the door frame
above the top hinge. A pivoting oper­ator that actuates the switch is
attached to the door face with special
security screws. The 220A is
designed for use on doors with 4-1/2”
or 5” hinges. Specify hinge size and
type (220A-5, 220A-4, etc.). Provided
with security fasteners.

TECHNICAL DATA:

• SIZE: 6-5/16” x 2-1/2” x 1-7/8”

• WEIGHT: 3 lbs.

• ELECTRICAL: Switch rating
SPDT 15 amps at 125 VAC or
.5 amps at 125 VDC

220A DOOR

POSITION SWITCH

F10

Revised 3/09

P.O. BOX 2021 • SAN ANTONIO, TX • 78297 • 210-533-1231 • FAX: [phone]

DOOR POSITION
SWITCHES FOR
SWINGING DOORS

APPLICATION:

The 240CPS is used where a
built-in
desired. This tamper proof unit is
mortised into the door and frame.
Indicator switch is mechanically
activated when the door is moved
from the closed position. A switch
adjustment is provided to allow for
varying field conditions. Provided
with security fasteners.

door indicator switch is

A C C E S S O R I E S

240CPS

CONCEALED POSITION

SWITCH

FEATURES:

• Handed, Specify LH or RH

• 180° maximum swing

• 12” long, 16 AWG UL wire leads
plug connector

with

• An eccentric stud on the control

provides a fine adjustment

arm

varying conditions

for

OPTIONAL FEATURES:

• Double Circuit, Specify 240CPS-2

This feature allows for an
additional

the 240CPS

by

circuit to be triggered

TECHNICAL DATA:

• CONCEALED (IN FRAME):

1-5/16”

• CONTROL ARM:

zinc plated

• TRACK(IN DOOR): 3/4” H x

1-1/4”
aluminum

• WEIGHT: 2 lbs.

• FACE PLATE: 14 GA

stainless steel (US32D finish)

•

ELECTRICAL: Switch is S.P.D.T.
type with a rating of 5 amps at
30

H x 1-1/2” W x 7-1/2” L

5/16” thick steel,

W x 12” L, extruded

alloy

VDC to 250 VAC

Left Hand Shown

Revised 3/09

FOR MORE INFORMATION, PLEASE CALL 210-533-1231

F11

FOOD PASS
ASSEMBLY

APPLICATION:

For use in hollow metal or plate
doors and walls. Opening area
measures 5" H x 1' 3-1/4" W.
Built-in stop positions the food
pass door as a shelf when open.
Key operated springlock provides
positive security and prevents
unauthorized use.

A C C E S S O R I E S

262 FOOD PASS

STANDARD FEATURES:

•

1017A snaplatch

• Two hinges

OPTIONAL FEATURES:

•

1010A deadlock
(Specify 262 x 1010A)

•

1010AM deadlock
(Specify 262 x 1010AM)

•

1017AM snaplatch
(Specify 262 x 1017AM)

•

1017AT snaplatch with thumbturn
only (Specify 262 x 1017AT)

TECHNICAL DATA:

• STANDARD FINISH: USP

• FRAME: 7 gauge mild steel

• LOCK: 1017A snaplatch

• HINGES: 3" H x 3" W x 5/32" TK
mild steel with cold-rolled
steel, non-removable pin

FRAME SIZE:

•
1' 8-1/4" L x 10" W

•

CLEAR OPENING:
5" H x 1' 3-1/4" W

Paracentric

Mogul

F12

Revised 9/13

P.O. BOX 2021 • SAN ANTONIO, TX • 78297 • 210-533-1231 • FAX: [phone]

ACCESS DOORS
AND PANELS

590 HINGED ACCESS DOOR

SIZE: 2’4” W x 3’4” H x 2-3/16” TK
WEIGHT: 105 LBS.

Provides access to plumbing or
utility spaces in security areas.

is constructed of 10 gauge

Door
steel plate flanged 1-3/4” all
around, hung on two Model
203FS hinges and locked with a
Model 1010A deadlock. Steel
frame is 7 gauge formed plate.
Specify type of wall construction
to determine anchor requirements.
Prime painted.

A C C E S S O R I E S

590 HINGED ACCESS DOOR

Revised 3/09

FOR MORE INFORMATION, PLEASE CALL 210-533-1231

F13

PUSHBUTTON
SWITCHES

906 MOMENTARY PUSHBUTTON

RATING: 10 amp
USAGE: Heavy-duty switch for
electric
requiring a maintained contact switch.
Suitable for inmate use.
Finish

locks, except for functions

US26D.

A C C E S S O R I E S

900 SERIES

MOMENTARY PUSHBUTTON

907 PUSHBUTTON

RATING: 6 amp
USAGE: This function is the same as
the 906. Faceplate is not available.
The 907 pushbutton becomes an
integral
Finish

part of the frame.

US32D.

Model 906

F14

Revised 3/09

Model 907

P.O. BOX 2021 • SAN ANTONIO, TX • 78297 • 210-533-1231 • FAX: [phone]

KEYSWITCHES

KEYSWITCHES

The 900 Series keyswitches are
recommended
areas or control cabinets.

930 THREE POSITION
MAINTAINED KEYSWITCH,
PARACENTRIC

RATING: 15 amp
USAGE: Extra heavy-duty
keyswitch for sliding door locking
device. Galvanized finish. Utilizes
paracentric key and cylinder.
Specify one or two way keying.

for use in secure

A C C E S S O R I E S

900 SERIES KEYSWITCHES

Model 930A shown

936 THREE POSITION
MAINTAINED KEYSWITCH,
MOGUL

RATING: 15 amp
USAGE: Heavy duty keyswitch for
sliding door locking devices.
US26D is standard cylinder finish,
US32D is standard plate finish.
Utilizes institutional (mogul-type)
key and cylinder.

Model 936 shown

Revised 3/09

FOR MORE INFORMATION, PLEASE CALL 210-533-1231

F15

HEAD OR FOOT
BOLT

10105 HEAD OR FOOT BOLT
APPLICATION:

For the inactive leaf of pairs of swinging
hollow metal, grating or steel plate
doors.

FUNCTION:

Actuated by means of a “spanner”
type key which extends the bolt into
appropriate receptacle in the floor or
jamb head. A special foot bolt
receptacle is available for
floor installations.

A C C E S S O R I E S

10105

HEAD OR FOOT BOLT

TECHNICAL DATA:

• STANDARD FINISH: Galvanized

• COVER: Cold-rolled steel plate

• CASE: Ductile iron

• LOCK BOLT: Cold-rolled steel

• SPANNER KEY: Cold-rolled steel

• SIZE: 5-3/8” H x 2-3/4” W x 1-7/8” TK

• WEIGHT: 5.5 lbs.

• BOLT SIZE: 1” Diameter

• BOLT THROW: 3/4”

10105R FLOOR RECEPTACLE

•

SIZE: 3” H x 1-5/8” DIA x 1-5/8” sq. Base

• WEIGHT: 2.25 lbs.

OPTI0NS:

• Head bolt keeper
Specify: “10105B” x USP

• Head bolt keeper switch
Specify: “10105CL” x USP

• Foot bolt receptacle Specify: 10105R

Note: Shown with cover plates used
only with grating and plate doors

10105R

FOOT BOLT

RECEPTACLE

10105K KEY

10105B

F16

Revised 3/09

10105CL

P.O. BOX 2021 • SAN ANTONIO, TX • 78297 • 210-533-1231 • FAX: [phone]

LOCK
MOUNTINGS

APPLICATION:

Used for mounting mechanical
paracentric locks on hollow
metal, steel plate or grating
doors. Note: The model
number for a specific lock
mounting is determined by
adding “HM”, “P”, “G” as a
prefix to the lock model number
i.e., HM-1080A-1, G-1070A-2.

A C C E S S O R I E S

LOCK MOUNTINGS

HM – Mounting for Hollow Metal Doors

TECHNICAL DATA:

• SIZE: Varies with application

• WEIGHT: Varies with
application

• HM - MOUNTING FOR
HOLLOW METAL DOORS:
7 gauge steel plate is attached
to door with security fasteners.
Comes with 218 Escutcheon.
For two-way locks, a second
escutcheon is required.

• P - MOUNTING FOR STEEL
PLATE DOORS: Formed
10 gauge steel plate is attached
to door with security
fasteners or rivets.

• G - MOUNTING FOR STEEL
GRATING DOORS:
Welds to grating door. 7 gauge
steel cover is attached to lock
mounting with security fasteners.
Comes with 218 Escutcheon.
For two-way locks, a second
escutcheon is required.

P – Mounting for Plate Doors

G – Mounting for Grating Doors

Revised 3/09

FOR MORE INFORMATION, PLEASE CALL 210-533-1231

F17