Page 1
WARNING: Warning devices are strictly
regulated and governed by Federal, State and
Municipal ordinances. These devices shall be
used ONLY on approved vehicles. It is the sole
responsibility of the user of these devices to
ensure compliance.
MOUNTING INSTRUCTIONS
Before starting the installation make certain
you have the correct bracket for your
application. A universal bracket is supplied.
The product is also designed for surface
mounting. Drill holes where required in the
mounting surface. The bolts provided can
slide back and forth in the bar’s rear
channel to align with the mounting holes.
!
WARNING
This product contains high intensity LED devices.
To prevent eye damage, DO NOT stare into light
beam at close range.
8 MODULE EXTERIOR BAR
10-30v w/ 50’ CABLE: EL3DØ8A(x)L(x)-24
SUPPLIED BAR
MOUNTING HARDWARE
UNIVERSAL BRACKET
ASSEMBLY INSTRUCTIONS
12v: EL3DØ8AØØ(x)
10-30v: EL3DØ8AØØ(x)-24
Install the UltraLITE by following the
assembly instructions provided with the
brackets and check for security.
Important: DO NOT over tighten mounting
screws or nuts. This could cause
permanent damage to the light or bracket.
Use appropriate hardware for mounting.
Universal bracket shown is supplied but
mounting screws are customer supplied.
PATTERN SELECTION
Because of the variety of configuring
options see separate sheets for detailed
instructions
WIRE HOOK-UP TABLE
Wire Color Connect to:
Blue Input 1 / Left
Green Input 2 / Right
Brown Input 3 / Warning
Red +Vdc
Black Ground (-)
White Pattern Select
Input Voltage (+Vdc): EL3DØ8AØØ(x) 10-16Vdc
EL3DØ8AØØ(x)-24 10-30Vdc
Current: 4 Amps Maximum
+Vdc
7.5A FUSE
BLUE
GREEN
BROWN
WHITE
RED
8 MODULE UltraLITE
BLACK
EL3D08A(xxx) 3.09
Page 2
WARNING: Warning devices are strictly
regulated and governed by Federal, State and
Municipal ordinances. These devices shall be
used ONLY on approved vehicles. It is the sole
responsibility of the user of these devices to
ensure compliance.
PATTERN SELECTION
1. Connect BLACK wire to ground.
2. Connect RED wire to +Vdc.
3. Connect GREEN, BLUE and BROWN wires
to +Vdc.
4. With power applied to the three wires,
momentarily apply power to WHITE wire to
change the directional arrow patterns.
5. While changing patterns, the UltraLITE will
display the left arrow pattern.
6. When you have chosen the directional
pattern, disconnect GREEN and BLUE wires
from power.
7. With the BROWN wire hooked up to power,
momentarily apply power to WHITE wire to
change the arrow warning pattern.
8. When you have selected the arrow warning
pattern, disconnect BROWN wire from
power.
9. You are finished configuring the UltraLITE.
!
WARNING
This product contains high intensity LED devices.
To prevent eye damage, DO NOT stare into light
beam at close range.
8 MODULE EXTERIOR BAR
FULL DIRECTIONAL ARROW
CONFIGURATION INSTRUCTIONS
12v: EL3DØ8AØØ(x)
10-30v: EL3DØ8AØØ(x)-24
10-30v w/ 50’ CABLE: EL3DØ8A(x)L(x)-24
ARROW PATTERNS
1 Solid Fast High Power
2 Solid Plus Fast High Power
3 Sequential Fast High Power
4 Sequential2 (2 lights) Fast High Power
5 Chaser Fast High Power
6 Solid Slow High Power
7 Solid Plus Slow High Power
8 Sequential Slow High Power
9 Sequential2 (2 lights) Slow High Power
10 Chaser Slow High Power
11 Solid Fast Low Power
12 Solid Plus Fast Low Power
13 Sequential Fast Low Power
14 Sequential2 (2 lights) Fast Low Power
15 Chaser Fast Low Power
16 Solid Slow Low Power
17 Solid Plus Slow Low Power
18 Sequential Slow Low Power
19 Sequential2 (2 lights) Slow Low Power
20 Chaser Slow Low Power
ARROW WARNING PATTERNS
1 Double Left and Right (Alternating)
2 Double Every Other Module
3 Q-Switch Left and Right (Alternating)
4 Q-Switch Every Other (Alternating)
5 Power Pulse Every Other (Alternating)
6 Power Pulse Left and Right (Alternating)
7 Quad Outer and Inner (Alternating)
8 Warp Every Other (Alternating)
9 Crossfire
10 HyperScan
11 SuperScan
12 Power Flash
Alternating: 1,2,3,4 alternates with 5,6,7,8
Every Other: 1,3,5,7 alternates with 2,4,6,8
EL3D08A(xxx) 3.09
Page 3
WARNING: Warning devices are strictly
regulated and governed by Federal, State and
Municipal ordinances. These devices shall be
used ONLY on approved vehicles. It is the sole
responsibility of the user of these devices to
ensure compliance.
PATTERN SELECTION
1. Connect BLACK wire to ground.
2. Connect RED wire to +Vdc.
3. Connect GREEN and BLUE wires to +Vdc.
4. With power applied to the two wires
momentarily apply power to WHITE wire to
change the directional arrow patterns.
5. While changing patterns, the UltraLITE will
display the left arrow pattern.
6. When you have chosen the directional arrow
pattern, disconnect GREEN and BLUE wires
from power.
7. Connect BROWN wire to +Vdc and
momentarily apply +Vdc to WHITE wire to
change the warning pattern displayed on the
UltraLITE.
8. When you have selected the warning pattern
for the UltraLITE, disconnect BROWN wire
from power.
9. You are finished configuring the UltraLITE.
!
WARNING
This product contains high intensity LED devices.
To prevent eye damage, DO NOT stare into light
beam at close range.
8 MODULE EXTERIOR BAR
DIRECTIONAL ARROW W/ WARNING TIPS
CONFIGURATION INSTRUCTIONS
12v: EL3DØ8A1Ø(x)
10-30v: EL3DØ8A1Ø(x)-24
10-30v w/ 50’ CABLE: EL3DØ8A(x)L(x)-24
ARROW PATTERNS for
1 Solid Fast High Power
2 Solid Plus Fast High Power
3 Sequential Fast High Power
4 Sequential2 (2 lights) Fast High Power
5 Solid Slow High Power
6 Solid Plus Slow High Power
7 Sequential Slow High Power
8 Sequential2 (2 lights) Slow High Power
9 Solid Fast Low Power
10 Solid Plus Fast Low Power
11 Sequential Fast Low Power
12 Sequential2 (2 lights) Fast Low Power
13 Solid Slow Low Power
14 Solid Plus Slow Low Power
15 Sequential Slow Low Power
16 Sequential2 (2 lights) Slow Low Power
SINGLE END MODULE WARNING PATTERNS
1 Traffic Mover Simultaneous
2 Q-Switch Alternating
3 RoadRunner Alternating
4 Power Pulse Alternating
5 Progressive Alternating
Simultaneous: 1 and 8 together
Alternating: 1 alternates with 8
EL3D08A(xxx) 3.09
Page 4
!
WARNING
This product contains high intensity LED devices.
To prevent eye damage, DO NOT stare into light
beam at close range.
WARNING: Warning devices are strictly
regulated and governed by Federal, State and
Municipal ordinances. These devices shall be
used ONLY on approved vehicles. It is the sole
responsibility of the user of these devices to
ensure compliance.
PATTERN SELECTION
1. Connect BLACK wire to ground.
2. Connect RED wire to +Vdc power.
3. Connect BLUE wire to +Vdc power.
4. With power applied to BLUE wire, momentarily apply power to WHITE
wire to move forward one warning pattern.
5. When you have chosen your first warning pattern, disconnect BLUE wire
from power.
6. The pattern you have selected will always display on the UltraLITE when
power is applied to the BLUE wire.
7. To setup your next warning pattern, connect GREEN wire to power.
8. With power applied to the GREEN wire, momentarily apply power to
WHITE wire to move forward one warning pattern.
9. When you have chosen you second warning pattern, disconnect GREEN
wire from power.
10. The pattern you have selected will always display on the UltraLITE when
power is applied to the GREEN wire.
11. To setup the last warning pattern, connect BROWN wire to power.
12. With power applied to the BROWN wire, momentarily apply power to
WHITE wire to move forward one warning pattern.
13. When you have chosen your third warning pattern disconnect BROWN
wire from power.
14. The pattern you have selected will always be displayed on the UltraLITE
when power is applied to the BROWN wire.
15. You are finished configuring the UltraLITE.
8 MODULE EXTERIOR BAR
4+4 SPLIT WARNING
CONFIGURATION INSTRUCTIONS
12v: EL3DØ8AØØ(x)
10-30v: EL3DØ8AØØ(x)-24
10-30v w/ 50’ CABLE: EL3DØ8A(x)L(x)-24
FLASH PATTERNS
1 Quint Flash Alternating
2 Warp Flash Alternating
3 Inter-cycle Flash Alternating
4 Double Flash Alternating
5 Quad Flash Alternating
6 3 Flashes / Second Alternating
7 3 Flashes / Second Simultaneous
8 Q-Switch Alternating
9 E-Pattern Single Flash Alternating
10 E-Pattern Double Flash Alternating
11 E-Pattern Single Flash Simultaneous
14 E-Pattern Double Flash Simultaneous
15 LiteRyder Sweep
16 Inter-cycle Flash Every Other Module
17 Double Flash Every Other Module
18 Quad Flash Every Other Module
19 Q-Switch Every Other Module
Alternating: 1,2,3,4 alternates with 5,6,7,8
Simultaneous: All modules on at same time
Every Other: 1,3,5,7 alternates with 2,4,6,8
EL3D08A(xxx) 3.09
Loading...