SoundOff Signal Taurus-Ghost Compass Light User Manual

Download

Page 1

COMPASS FENDER LIGHT

ECPGHKF1B(xx) - FORD TAURUS

- Fender Light pre-assembly -

Wire

hole

#6 Torx Screws 2x

#10-16 Torx Screws 2x

-View from outside of fender-

Mounting

Bracket

Trim Panel

Ghost

Light Assembly

Fig. 1

- View from inside of fender-

All 5 mounting clips must rest on inside edge of body opening. Press ﬁrmly to ensure all 5 clips are engaged.

Fig. 3

INSTALLATION:

1. Remove the vent panel from the vehicle per manufacturers instructions and install the supplied clip nut onto the fender of the vehicle. Figure 4.

2. Slide the Ghost Light Assembly into the Trim Panel making sure the label is facing down. Figure 1.

3. Run the Ghost Light cable through the wire hole in the mounting bracket as shown in ﬁgure 1.

4. Install the Mounting Bracket on the back of the Ghost Light and the Trim Panel part as shown. Figure 1. Use the 2 supplied #6 and #10 Torx Screws to attach the Mount ing Bracket to the Trim Panel. Tighten Snug. Figure 1.

5. Run the cable assembly into the fender and install to the power source. See page 2.

6. Snap the Compass Fender Light assembly to the fender opening.

7. Secure the assembly with the supplied #8 Phillips screw.

OPERATION:

1 Make secure connections as shown in

Wire Hook-Up Table below.

2 To sync light and make pattern selections

see reverse side.

Fig. 2

Warning devices are strictly regulated and governed by Federal, State and Municipal ordinances. These devices shall be used ONLY on approved vehicles. It is the sole responsibility of the user of these devices to ensure compliance.

1.800.338.7337 / www.soundoffsignal.com

WIRE HOOK-UP TABLE

WIRE COLOR: CONNECT TO:

RED +10-16Vdc

BLACK Ground (-)

INSTALL

CLIP NUT

Fig. 4

This product contains high intensity LED devices. To

prevent eye damage, DO NOT stare into the light

IMPORTANT INFORMATION:

To review our Limited Warranty Statement & Return Policy for this or any SoundOff Signal product, visit our website at www.soundoffsignal.com/sales-support.

If you have questions regarding this product, contact Technical Services, Monday - Friday, 8 a.m. to 5 p.m. at 1.800338.7337 (press #4 to skip the automated message).

Questions or comments that do not require immediate attention may be emailed to techsupport@soundoffsigal.com.

SUPERIOR CUSTOMER RELATIONSHIPS. SMARTLY DESIGNED LIGHTING & ELECTRONIC SOLUTIONS.

WHITE ID/Pattern Select

WARNING

beam at close range.

ECPGHKF1B(xx) 11.12

Page 2

COMPASS FENDER LIGHT

ECPGHKF1B(xx) - FORD TAURUS

2 SINGLE LIGHTS

Follow the ID selection steps and set the GHOST to the following ID:

IMPORTANT: Make sure both lights ﬂash the same pattern!

- Both assemblies simultaneous with individual lights alternating.

- Example: Driver/Passenger sim; Dr. (left alt right) Pass. (left alt right)

- Set both GHOST Assemblies to ID#1

- Both assys. alternating with individual lights alternating.

- EX: Dr./Pass. alt; Dr. (left. alt. right.) Pass. (right alt. left)

- Set one GHOST to ID#1 and the other to ID#3

- Both assys. alternating with individual lights simultaneous

- EX: Dr./Pass. alt; Dr. (left sim left) Pass. (right sim right)

- Set one GHOST to ID#2 and the other to ID#4

- Both assys. simultaneous with individual lights simultaneous.

- EX: Dr./Dr. sim; Dr. (left sim left) Pass. (right sim right)

- Set both Ghost housings to ID#2

X-PATTERN - To obtain X-Patterns, follow the ID SELECTION steps and set one of the four GHOST lights to ID#1, one to ID#2, one to ID#3, and one to ID#4. Then proceed to the PATTERN SELECTION steps.

NOTE: Be sure to mount each GHOST in the correct placement based on ID#.

PATTERN SELECTION

1. Disconnect WHITE wire from any connections if applicable.

2. Turn GHOST ON.

3. Momentarily touching and removing the WHITE wire(s) to ground will advance the GHOST to the next ﬂash pattern. Touching and removing the White wire for more than a few seconds will allow you to change the GHOST to the previous pattern. See ﬂash pattern table. Continuing to touch and remove the WHITE wire(s) to ground will allow you to scroll through the pattern list. After pattern #33 is reached the list will start over again at pattern #1.

X-Pattern Sequence

ID#1> ID#4> ID#2> ID#3

X-Pattern Light Head Placement

ID#4 ID#2 ID#3 ID#1

NOTE: The GHOST is equipped with ﬂash pattern memory. Once you

have selected a pattern the GHOST will always activate to that pattern every time the unit is turned on. Tape up and secure WHITE wire so that it will not accidentally change your selected pattern.

Ghost Sync Conﬁguration Instructions IMPORTANT! A MAXIMUM OF 4 SINGLE LIGHTS CAN BE SYNCED TOGETHER

1. Set ID# a. Identify which pattern and sequence you want and look up

ID# settings at left. b. Connections i. RED: +10-16Vdc ii. WHT: +10-16Vdc (Note: you will need to disconnect after

power is applied) iii. BLK: Ground c. Apply power to unit d. Without disconnecting power from unit, disconnect WHT wire e. Momentarily connect WHT to Ground to change ID # i. Identify ID# by number of sequential ﬂashes ii. Possible ID#s: 1 – 4 f. Disconnect power from unit to get out of ID mode.

2. Set Pattern a. Reapply power to units. b. Once all Light Head ID#s are conﬁgured, make sure all

lights are ﬂashing the same pattern. c. Connect corresponding colored wires of all units together:

RED to RED, etc. d. Change Pattern i. Momentarily connect WHT wires to Ground ii. Observe pattern change on all lights connected e. Insulate all wires by taping with electrical tape

3. Connect Master Switch for Application a. IMPORTANT! Ensure WHT Pattern/Sync Wires are tied

together

PATTERN RESET

1. Remove power

2. Place WHITE (sync) wire to ground

3. With sync wire grounded, re-power RED wire

4. Maintain for one second (light will dim)

5. Remove power and ground (pattern 1 set)

SLAVE MODE The GHOST is capable of being activated through the use of a user

supplied ﬂasher by putting it in slave mode.

1. Permanently connect the GHOST WHITE and BLACK wire to a

good, convenient ground.

2. Connect the GHOST RED wire, through a 5Amp fuse, to the output

of a +10-16Vdc switching ﬂasher.

Flash Patterns

Pattern Name 1 Light

1. Quint

2. Warp

3. Inter-Cycle Flash

4. Double Flash

5. Quad Flash

6. PowerPulse™

7. RoadRunner™

8. Q-Switch™

9. RoadRunner™ Steady Burn

10. Quad Steady Burn

11. E-Ideal Single Flash

12. E-Ideal Double Flash

13. Quad2 Flash

14. Double2 Flash

15. X-Warp

16. X-Double

17. PowerRunner

18. LCR Quint

19. Warp

20. Ultra Warp

21. Thunder & Lightning

22. Lite Speed

23. SuperSonic

24. LCR Lite Speed

25. SuperSonic Ultra

26. Tempo Shift

27. Tempo Shift Warp

28. SBE2

29. C

30. U

31. Ultra Glow

32. Cyclone

33. Chameleon

x x x 70

x x x 350

x x

x x x 70

x x x 80

x x x 180

x x x 113

x x

x x 113

x x 80

x x x 200

x x x 146

x x x 67

x x x 95

x x x

x x x 545

x x

x x x 85

x x 170

x x x

x x x 67

x x x 200

x x x 176

x x x

Alternating 2

Lights

Silmultaneous 2

Lights

X-Pattern

4 Lights

F.P.M.

(Flashes /

Minute)

1.800.338.7337 / www.soundoffsignal.com

ECPGHKF1B(xx) 11.12

Page 3

COMPASS FENDER LIGHT

ECPGHKF1B(xx) - FORD TAURUS

REMOVAL PROCEDURE:

1. Unclip the bottom 2 mounting clips using a small putty knife to disengage the mounting clips.

2. Rotate light assembly and lift off.

TECHNICAL SPECIFICATIONS

Overall Dimensions: 14”H x 2.75”W x 1.5”D

Flash Patterns: 33 ﬂash patterns

Input Voltage Range: 10 - 16 Vdc

Current Consumption: ~0.75 Amps /module*

# of LEDs: 6 Generation 3 LEDs

Light Sync Technology: Yes

Operating Temperature: -40º to +65º C

*Pattern Dependent

Parts & Accessories:

GHOST SM Module PGHSTO(x)B-(x) LH GHOST Trim Panel PGH3FLTP2L RH GHOST Trim Panel PGH3FLTP2R LH GHOST Plastic Backing Bracket PNT3FLMB2L RH GHOST Plastic Backing Bracket PNT3FLMB2R

1.800.338.7337 / www.soundoffsignal.com

ECPGHKF1B(xx) 11.12

SoundOff Signal Taurus-Ghost Compass Light User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual