SINGLE EXTERIOR DECK / GRILLE
WARNING SYSTEM
ASSEMBLY INSTRUCTIONS
EP2SGS1(x)
!
WARNING
This product contains high intensity LED
devices. To prevent eye damage, DO NOT
stare into light beam at close range.
WARNING: Warning devices are strictly
regulated and governed by Federal, State and
Municipal ordinances. These devices shall be
used ONLY on approved vehicles. It is the sole
responsibility of the user of these devices to
ensure compliance.
BRACKET MOUNTING
Important: DO NOT over tighten
mounting screws or nuts. This could
cause permanent damage to the bracket
1. Locate flat mounting location for
Predator II Light Bracket.
2. When position of bracket is determined
use supplied template for hole
locations.
3. Drive in Customer Supplied Hex Head
screws. Leave about a 1/16” space
between the mounting surface and
underside of screw head.
4. Place Light over screws using the
holes in brackets and slide to the right
to lock the brackets underneath the
head of the bolts.
5. Using a open-end wrench, tighten the
hex head bolts down tight to secure
the light to the mounting surface.
6. Adjust angle of the light to best suit
your application by loosening the 2
nuts on either end of the light.
7. After the Predator is set to the desired
angle, tighten the 2 nuts on either end
of the light. DO NOT OVER TIGHTEN
nuts as damage to bracket or light can
occur. Tighten nut until snug plus 1/8
turn.
8. Make electrical connections using the
following instructions.
NOTE: The PREDATOR II is a factory
sealed unit that CANNOT be serviced
in the field. Any attempt to gain
access to the PREDATOR II unit will
most likely cause permanent damage
and void its warranty.
IMPORTANT: DO NOT connect this
device to a strobe power supply.
OPERATING INSTRUCTIONS
See setup procedure on second page.
The single Predator II comes equipped
with an internal flasher with 33 user
selectable patterns that can be
synchronized either alternating or
simultaneous with up to three other lights.
It can also be put into slave mode and
driven through an external flasher.
1. Connect the PREDATOR II BLACK wire
to a good, convenient ground.
2. Connect the PREDATOR II RED wire to
one side of a user supplied on/off switch.
Connect the other side of the switch,
through a 5Amp fuse, to a source of
+10-30Vdc.
Place Light over screws using keyway in brackets
Install Screws (user supplied)
first using template on back
Slide Light to the Right and tighten screws using box end wrench
SCREW PLACEMENT DRILL TEMPLATE
(Be sure to use appropriate drill size for your screw size)
2.77
EP2SGS1(x) 02/08
SINGLE EXTERIOR DECK / GRILLE
WARNING SYSTEM
ASSEMBLY INSTRUCTIONS
EP2SGS1(x)
!
WARNING
This product contains high intensity LED
devices. To prevent eye damage, DO NOT
stare into light beam at close range.
Predator Sync Configuration Instructions
1. Set ID#
a. Identify which pattern and sequence you want and look up ID#s on table.
b. Connections
i. RED: +12Vdc
ii. WHT: +12Vdc (Note: you will need to disconnect after power is applied)
iii. BLK: Ground
c. Apply power to unit
d. Without disconnecting power from unit, disconnect WHT wire
e. Momentarily connect WHT to Ground to change ID #
i. Identify ID# by number of sequential flashes
ii. Possible ID#s: 1 – 4
f. Disconnect power from unit to get out of ID mode.
2. Set Pattern
a. Reapply power to units.
b. Once all Light Head ID#s are configured, make sure all lights are flashing the
same pattern
c. Connect corresponding colored wires of all units together: RED to RED, etc.
d. Change Pattern
i. Momentarily connect WHT wires to Ground
ii. Observe pattern change on all lights connected
e. Insulate all wires by taping with electrical tape
3. Connect Master Switch for Application
a. IMPORTANT! Ensure WHT Pattern/Sync Wires are tied together
1LIGHT
Single Light Operation: Follow the ID Selection steps and set the LED3 to ID#1 if it is not already. NOTE: Steady Burn is produced
for patterns 9 & 10 in Single Operation.
PATTERN SELECTION
1. Disconnect WHITE wire from any
connections if applicable.
2. Turn PREDATOR II ON.
3. Momentarily touching and removing the WHITE wire(s) to
ground
will advance the PREDATOR II to the next flash pattern.
Touching and
removing the White wire for more than a few seconds will
allow you to change the PREDATOR II to the previous
pattern. See flash pattern table. Continuing to touch and
remove the WHITE wire(s) to ground will allow you to scroll
through the pattern list. After pattern #33 is reached the list
will start over again at pattern #1.
NOTE: The PREDATOR II is equipped with flash pattern
memory. Once you have selected a pattern the PREDATOR II
will always activate to that pattern every time the unit is turned
on. Tape up and secure WHITE wire so that it will not
accidentally change your selected pattern.
PATTERN RESET
1. Remove power.
2. Place WHITE (sync) wire to ground.
3. With sync wire grounded, re-power RED wire.
4. Maintain for one second (light will dim).
5. Remove power and ground (pattern 1 set).
SLAVE MODE
The LED3 is capable of being activated through the use of a
user supplied flasher by putting it in slave mode.
1. Permanently connect the LED3 WHITE and BLACK wire to a
good, convenient ground.
2. Connect the LED3 RED wire, through a 5Amp fuse, to the
output of a +10-30Vdc switching flasher.
NOTE: The LED3 is a factory sealed unit that CANNOT be
serviced in the field. Any attempt to gain access to the LED3
unit will most likely cause permanent damage and void its
warranty.
X-Pattern Sequence
ID#1 > ID#4 > ID#2 > ID#3
X-Pattern Light Head Placement
ID#4 ID#2
ID#3 ID#1
FLASH PATTERNS for
SINGLE HEAD EXTERIOR PREDATOR II (EP2SGS1(x))
2 LIGHTS
ALTERNATING: To obtain Alternating patterns, follow the ID SELECTION steps and set one LED3 to ID#1 and the other to ID#3.
Then proceed to the PATTERN SELECTION steps.
SIMULTANEOUS: To obtain Simultaneous patterns, follow the ID SELECTION steps and set both LED3 lights to ID#1. Then
proceed to PATTERN SELECTION steps.
4 LIGHTS
X-Pattern: To obtain X-patterns, follow the ID SELECTION steps and set one of the four LED3 lights to ID#1, one to ID#2, one to
ID#3, and one to ID#4. Then proceed to PATTERN SELECTION steps. NOTE: Be sure to mount each LED3 in the correct
placement based on ID#.
EP2DGS1(x) 02/08
Loading...