Soundoff Signal nROADS ENRBCSHM 1 Z, nROADS ENRBCSHC 1 Z Series, nROADS ENRBCSLC 1 Z Series, nROADS ENRBCSLM 1 Z Series Series Manual
HIGH DOME BEACON
HIGH DOME
MAGNET MOUNT - ENRBCSHM(x)1(x)Z(xxx)
COMBO: FLAT/PIPE MOUNT - ENRBCSHC(x)1(x)Z(xxx)
LOW DOME
MAGNET MOUNT - ENRBCSLM(x)1(x)Z(xx)
COMBO: FLAT/PIPE MOUNT - ENRBCSLC(x)1(x)Z(xxx)
Distributed by
TECHNICAL SPECIFICATIONS
Dimensions:
Input Voltage: 9-17.5Vdc
Standby Current:
<0.0001 Amps after 10 seconds of no
active control inputs
Reverse Polarity Protection: Yes
Electrical Transient Protection: ISO7637-2 for 12V systems
Wiring:
Approx. 18" length. Type TXL 4x 16AWG
Power/Ground, 6x 20AWG Control
CURRENT CONSUMPTION
MODULE
CONFIGURATION
3 LED Single Color 9-17.5Vdc 0.5 Amps 3.2 Watts
6 LED Single Color 9-17.5Vdc 1.0 Amps 6.4 Watts
9 LED Single Color 9-17.5Vdc 1.5 Amps 9.6 Watts
12 LED Single Color 9-17.5Vdc 2.0 Amps 12.8 Watts
12 LED Dual Color 9-17.5Vdc 1.0 Amps 6.4 Watts
18 LED Tri Color 9-17.5Vdc 1.0 Amps 6.4 Watts
INPUT VOLTAGE
RANGE
CURRENT DRAW
(MAXIMUM)
WATTS FLASHING
@ 12.8Vdc
WARNING
•HIGH CURRENT interconnects must be properly terminated. Poor crimp quality can cause heat
build-up and fire. Follow crimp connector manufacturer instructions.
•DO NOT install this product or route any wires in the Air Bag Deployment Zone. Refer to vehicle
Owner’s Manual for deployment zones.
•Do NOT use system to disconnect headlights, brake lights or other safety equipment.
•Unit may become hot to touch during normal operation.
•Failure to properly install connectors, fuses or wiring may cause vehicle failure or fire.
•Installation must only be performed by trained technician. Installer must determine vehicle wiring
configuration and proper integration of system.
•Use proper wire gauge. All power wires connecting to positive (+) or negative (-) battery terminal
or local chassis ground (-) must be sized to supply at least 125% of max. current and properly fused at
power source.
•Install protective grommets when routing wire through firewall or metal.
Installers and users must comply with all applicable federal, state and local laws regarding use and installation of warning devices.
Improper use or installation may void warranty coverage. To review our Limited Warranty Statement & Return Policy for this or any SoundOff Signal product, visit our website at
www.soundoffsignal.com/sales-support. If you have questions regarding this product, contact Technical Services, Monday - Friday, 8 a.m. to 5 p.m. or after hours 5 p.m. to 8 p.m. EST
at 1.800338.7337 (press #4 to skip the automated message). Questions or comments that do not require immediate attention may be emailed to techservices@soundoffsigal.com.
1.800.338.7337 / www.soundoffsignal.com
1.
SUPERIOR CUSTOMER RELATIONSHIPS. SMARTLY DESIGNED LIGHTING & ELECTRONIC SOLUTIONS.
NOTICE:
WARNING
!
This product contains high intensity LED devices. To
prevent eye damage, DO NOT stare into the light
beam at close range.
Please see pages 2-3 for Mounting Instructions
nROADS Beacon 05.16
Screw together until snug
and "REAR" is facing the rear
of the vehicle
1" NPT Pipe
"REAR" needs to face the
rear of the vehicle
Mounting Gasket
nROADS Mounting Instructions
Flat Mount:
1. Using the supplied gasket, mark the center hole
and three mounting holes on the surface the
beacon will be mounted to.
2. Drill your holes.
a. The center hole should be large enough for the
wires to pass, between 5/8" and 1".
b. The 3 mounting holes should be drilled for
clearance for #10 bolts (1/4").
3. Using #10-32 bolts of suitable length (installer
supplied) secure the beacon to the mounting
surface making sure the gasket is between
the beacon and the mounting surface. (SoundOff
Signal recommends using flat washers and lock
washers to secure the beacon to your mounting
surface).
Pipe Mount:
1. The beacon is pre-threaded to fit a 1" NPT pipe.
2. Insert wires into the pipe making connections you
wish to use.
3. Screw the beacon on the pipe until snug.
4. The aluminum base is marked "REAR". Rotate the
beacon until the "REAR" is facing the back of the
vehicle. This is important for specific light
modes.
PIPE MOUNT
2.
Mounting
Holes x3
FLAT MOUNT
Mounting
Surface
5/8"-1" Center Hole
nROADS Beacon 05.16
Magnets x3
"REAR" needs to face
the rear of the vehicle
nROADS Mounting Instructions
Magnet Mount:
1. Locate surface where beacon will be mounted.
2. Place beacon with the "REAR" facing the rear of
the vehicle. This is important for specific modes.
Cig Plug Operation:
1. See Cig Plug diagram at left for POWER ON/OFF
and PATTERN SELECT switch locations.
2. Turn beacon ON by pressing the POWER ON/OFF
switch to the ON position.
3. With beacon OFF, press and hold PATTERN
SELECT switch for 1 second until you see the
beacon flash the new pattern and release.
4. Holding the PATTERN SELECT switch for >5
seconds while the beacon is ON will reset the
beacon to pattern #0.
PATTERN
POWER ON/OFF
MAGNET MOUNT
3.
CIG PLUG
nROADS Beacon 05.16
ELECTRICAL INSTALLATION (applies to permanent mounting options only)
Power Wires:
1. Route customer supplied power and ground cables which are properly sized for the current consumption of the beacon (rated for a minimum of 125% above maximum current draw) between
the power source (battery) and the beacon power and ground cables.
2. Install a maximum of 20Amp Fuse (customer supplied) to the end of the power cables as close to the power source (battery) as possible.
a. Remove the fuse before connecting any wires to the battery.
b. DO NOT USE CIRCUIT BREAKER OR FUSIBLE LINK.
3. Connect the other end of the Fuse to the POSITIVE (+) terminal of the battery.
a. Do NOT use any more than 2ft of wire between the battery terminal and the fuse and ensure the wire is protected and secured from being cut into; this is non-fused wire.
4. Connect the BLACK wire to the factory chassis ground right next to the battery and the the ground cables of the beacon.
Control Wires (Blue, Orange, Yellow & Pink):
1. Route customer supplied wires between switch panel and the Blue, Orange, Yellow, and/or Pink wires. Use 20AWG type TXL wire as required to extend the length of the wires to reach the
customer supplied switches.
2. The +12V supply to the control wires must be over-current protected to protect the wires and product against the possibility of a short circuit. A 1 amp fuse will be sufficient since the control
wire inputs require less than 10mA per input to activate.
Synch Wire (Green):
1. Connect the green wire to other Sync2 compatible products (nFORCE Secondary Light, nFORCE FIT & Dual Color Intersector Lights) which are on the vehicle and need to synchronize the flash
pattern. All product with the green wires connected must be operating
the same flash pattern otherwise incorrect flash pattern timing will occur.
2. If synchronized flash patterns to other product are not required, blunt cut and tape the end of the green wire to ensure the wire is protected from being unintentionally grounded while in service.
Pattern Select/Configuration Wire (White):
1. Applying a momentary ground on the white wire will configure the product. Refer to the production configuration section of the installation instructions for setup.
2. Once product is configured, blunt cut and tape the end of the white wire to ensure the wire is protected from being unintentionally grounded while in service and changing the configuration.
+9-17.5Vdc
Customer Supplied Wire
20AMP
Ground
Customer Supplied Wire
BATTERY
WARNING
!
ALL CUSTOMER SUPPLIED POWER WIRES CONNECTING TO THE POSITIVE (+) OR NEGATIVE (-) BATTERY
TERMINAL OR LOCAL CHASIS GROUND (-) MUST BE SIZED TO SUPPLY AT LEAST 125% OF THE MAXIMUM
CURRENT AND PROPERLY FUSED AT THE POWER SOURCE WITH APPROPIATELY RATED FUSE.
4.
10AMP
10AMP
1AMP
Customer Supplied
Fuses
Momentary Ground
to Configure Product
Red
Red
Black
Black
Customer Supplied
Blue
Switches
Pattern Select
Yellow
Orange
Pink
Green
White
Sync Wire
Connected to Other Sync 2 Products
to Synchronize Flash Pattern (nFORCE
Secondary Light, nFORCE FIT & Dual Color
Intersector Lights)
nROADS Beacon 05.16
Loading...