SoundOff Signal nLINE Running User Manual

nLINE RUNNING LIGHT

#ENL172(x)-L - 72” LEFT WIRE EXIT
#ENL172(x)-R - 72” RIGHT WIRE EXIT
#ENL160(x)-L - 60” LEFT WIRE EXIT
#ENL160(x)-R - 60” RIGHT WIRE EXIT
#ENL148(x)-L - 48” LEFT WIRE EXIT
#ENL148(x)-R - 48” RIGHT WIRE EXIT
#ENL136(x)-L - 36” LEFT WIRE EXIT
#ENL136(x)-R - 36” RIGHT WIRE EXIT

Flash Patterns

Pattern Name

1. Quint

2. Warp**

3. Double Flash**

4. Quad

5. Power Pulse

6. Road Runner

7. Quad 2

8. Double 2

9. Chase 1

10. Chase 2**

Strip Lights have 3, 4, 5 or 6 segments depending on length. These segments alternate
flashing patterns 1-8 (odd segments flashing together & even segments flashing together.

F.P.M.

(Flashes / Minute)

70

350

70

80

180

113

68

95

117

70

Tech Specs

Flash Patterns:

Light Sync:

Mounting:

Input Voltage:

Dimensions:

Operating Temp.:

Important Information:

• Warning devices are strictly regulated and governed by Federal, State and Municipal ordinances.
These devices shall be used ONLY on approved vehicles. It is the sole responsibility of the user of these
devices to ensure compliance.

• DO NOT install this product or route any wires in the Air Bag Deployment Zone. Refer to your vehicle
Owner’s Manual for the location of any air bag deployment zones.

• DO NOT connect this device to a strobe power supply. This product is self-contained and does not
require an external power supply.

Warning devices are strictly regulated and governed by Federal, State and Municipal ordinances. These devices shall be used ONLY on approved vehicles. It is the sole responsibility of the user of these devices to ensure compliance.

1.800.338.7337 / www.soundoffsignal.com

**Does not meet SAE Standard

nLINE Strip Light

10 Flash Patterns

Yes

Surface Mount

10 - 16 Vdc

Width x Height x Depth
72” W x 2.25” H x .75” D
60” W x 2.25” H x .75” D
48” W x 2.25” H x .75” D
36” W x 2.25” H x .75” D

-40° to +65° C

To review our Limited Warranty Statement & Return Policy for this or any SoundOff Signal product, visit our website at www.soundoffsignal.com/sales-support.

If you have questions regarding this product, contact Technical Services, Monday - Friday, 8 a.m. to 5 p.m. at 1.800338.7337 (press #4 to skip the automated message).

Questions or comments that do not require immediate attention may be emailed to [e-mail].

SUPERIOR CUSTOMER RELATIONSHIPS. SMARTLY DESIGNED LIGHTING & ELECTRONIC SOLUTIONS.

PATTERN SELECT

1. With light powered, touch White wire to
Red Power wire for 1 second.

PATTERN RESET

1. With light powered, touch White wire to
Red wire for 3 seconds.

2. Remove White wire from power. Pattern
resets to 1.

SYNC MULTIPLE LIGHTS

1. Set up all lights to the same pattern

2. Connect White wires of all lights to sync
together.
a. Note, only 6 lights can be synced
together.
b. Insulate connections

3. Green Wire Connection
a. For Simultaneous Flashing of a group of
lights:
i. Connect all Green wires together of

the group of lights desired to flash in
unison.
ii. All Green wires connected together
form one light group
b. For alternating flashing of a group of
lights:
i. Connect one group of Green wires
to Power (+Vdc)
ii. These lights will flash in unison.
iii. Connect one group of Green wires
together but leave floating.
iv. These lights will flash in unison.
v. Together, both light groups will
alternate.
vi. For two lights simply connect one
Green wire to Power (+Vdc) and
leave the other Green wire floating.
vii. Insulate connections.

IMPORTANT INFORMATION:

INSTALLATION:

1. Establish a position on the bottom of the
running board on the left or right side of
your vehicle.

2. Use the screw holes on the running board
as a template to mark locations of screw
access holes.

3. Use a 5/16” diameter drill for the wire holes

4. Size pilot holes for mounting screws
appropriately.

5. Fasten light using mounting
screws (NOT SUPPLIED).

WIRE HOOK-UP TABLE

WIRE COLOR: CONNECT TO:

RED +Vdc

BLACK Ground (-)

WHITE

GREEN

!

This product contains high intensity LED devices. To

prevent eye damage, DO NOT stare into the light

Pattern Select/Sync

Simultaneous or

Alternate

WARNING

beam at close range.

nLINE Running Board Lites 7.14

Pg. 1