Page 1
SAE CLASS 1 SURFACE MOUNTS
SINGLE MOUNT VERSION
LIGHT ASSEMBLY
HOUSING
DOUBLE MOUNT VERSION
GASKET
TECHNICAL SPECIFICATIONS
SURFACE MOUNT NEXUS
Single Mount
Dimensions:
Double Mount
Dimensions:
Input Voltage: 10 - 16 Vdc or 10 - 30 Vdc*
CURRENT CONSUMPTION
6, 12 Split &
18 Tri-Color
<1.0A @12.8 Vdc <0.6A @ 25.6 Vdc
9 LED Single Color <1.5A @ 12.8 Vdc <0.9A @ 25.6 Vdc
12 LED Single Color <2.0A @12.8 Vdc <1.2A @ 25.6 Vdc
BACK VIEW OF SINGLE SURFACE MOUNT SHOWN W/O
5.0”L x 1.72”H x 1.50”D
5.0”L x 3.13”H x 1.50”D
10-16 Vdc 10-30 Vdc *
* - Special Order
RUBBER MOUNTING GASKET
- TYPICAL FOR BOTH VERSIONS-
INSTALLATION:
SURFACE MOUNT
1) Establish a position on the vehicle. Use
the gasket (provided) as a template
to drill 1/4” diameter wire hole and
pilot holes for mounting screws.
Note: pilot holes are 4.91” on center.
Caution: Do not stretch gasket as
this may change the required hole
spacing.
INFORMATION FOR NEXUS
SECONDARY:
WIRE HOOK-UP TABLE
WIRE COLOR: FUNCTION:
RED Power
BLACK Ground
GREEN Sync2 *
WHITE Pattern Select
DO NOT DAMAGE, BLOCK OR
TOUCH THE BREATHER PATCHES
Please see reverse for
Technical Specifications
Important Information:
• Warning devices are strictly regulated and governed by Federal, State and Municipal ordinances.
These devices shall be used ONLY on approved vehicles. It is the sole responsibility of the user of these
devices to ensure compliance.
• DO NOT connect this device to a strobe power supply. This product is self-contained and does not
require an external power supply.
To review our Limited Warranty Statement & Return Policy for this or any SoundOff Signal product please visit our website at www.soundoffsignal.com and select the “Warranty & Returns”
link along the left column of our home page. If you have questions regarding this product please contact Technical Services, Monday - Friday, 8 am to 5 pm at 1.800.338.7337, press #4 to
skip the automated message. Questions or comments that do not require immediate attention may be emailed to techsupport@soundoffsignal.com.
1.800.338.7337. / www.soundoffsignal.com / Thank you for trusting us with your safety!
* Will NOT work w/ other sync
products such as Ghost, LED3,
& Intercector.
MAKE SURE DRAIN
HOLE IS FACING DOWN
ENFSLXSS 7.12
Page 2
SLAVE MODE
The NFORCE™ is capable of being activated through the use of a user
supplied flasher by putting it in Slave Mode.
1. Permanently connect the NFORCE™ WHITE and BLACK wire to a good,
convenient ground.
2. Connect the NFORCE™ RED wire, through a 5amp fuse, to the output of
a +10-16Vdc switching flasher.
PATTERN SELECT & SYNC
CONFIGURATION INSTRUCTIONS
Connecting the WHITE wire to power will
allow you to use the secondary feature on
your Nexus Secondary Light.
4.91"
2.46"
• 1-color module = Cruise Mode
(10% brightness, non - ashing)
• 2 & 3 - color modules = Takedown
(100% Steady - burn)
- For 2-color modules this is the 2nd color
- For 3-color modules, this is the 3rd color
SECONDARY FEATURE:
HOLE
1.30"
.25"
2X
PILOT HOLE
LOCATION 2X
SETUP LIGHTS:
• Sequence type
-1 or 2. The modules will ash simultaneously if they are set to the same number.
The modules will have an alternate ash if
set to different numbers.
• Color swap
- Off or On. 2-color and 3-color modules, it
DOUBLE SURFACE MOUNT TEMPLATE
changes which color ashes rst.
This is useful when syncing multiple lights
2.46
“
4.91
“
.25
HOLE
“
Touching the WHITE wire to the ground will allow
you to change various setting on the module.
SECONDS USER INTERFACE
PILOT HOLE
LOCATION
2X
SINGLE SURFACE MOUNT TEMPLATE
FROM TO VISUAL FEEDBACK ACTION TAKEN
0 1 STEADY-HIGH (60%) FORWARD ONE PATTERN
1 2 STEADY-LOW (30%) BACKWARD ONE PATTERN
2 3 OFF COLOR SWAP (OFF OR ON )
3 4 STEADY - HIGH SEQUENCE TYPE (1 OR 2)
4 5 STEADY - LOW RESET TO PATTERN 1
5 6 OFF
If held longer than 6 seconds, the light will go back to flashing the current
pattern and no action will be taken.
FACTORY RESET (PATTERN 1, COLOR
SWAP: OFF, SEQUENCE TYPE: 1)
ENFSLXSS 7.12
Page 3
PATTERN LIST
1 COLOR MODULE PATTERNS
# COLORS NUMBER NAME
1 1 QUINT
2 WARP
3 INTER-CYCLE
4 DOUBLE
5 QUAD
6 POWER PULSE
7 ROAD RUNNER
8 Q-SWITCH
STEADY-BURN DRIVER ROADRUNNER
9
10
11 QUAD 2
12 DOUBLE 2
(SEQUENCE TYPE 1: STEADY BURN,
SEQUENCE TYPE 2: ROADRUNNER)
STEADY-BURN DRIVER TITLE 13 QUAD
(SEQUENCE TYPE 1: STEADY BURN,
SEQUENCE TYPE 2: TITLE 13 QUAD)
2 COLOR MODULE PATTERNS
# COLORS NUMBER NAME
2 1 QUINT
2 WARP
3 INTER-CYCLE
4 DOUBLE
5 QUAD
6 POWER PULSE
7 ROAD RUNNER
8 Q-SWITCH
STEADY-BURN DRIVER ROADRUNNER
9
10
11 QUAD 2
12 DOUBLE 2
1 13 QUINT
14 WARP
15 INTER-CYCLE
16 DOUBLE
17 QUAD
18 POWER PULSE
19 ROAD RUNNER
20 Q-SWITCH
21
22
23 QUAD 2
24 DOUBLE 2
(SEQUENCE TYPE 1: STEADY BURN,
SEQUENCE TYPE 2: ROADRUNNER)
STEADY-BURN DRIVER TITLE 13 QUAD
(SEQUENCE TYPE 1: STEADY BURN,
SEQUENCE TYPE 2: TITLE 13 QUAD)
STEADY-BURN DRIVER ROADRUNNER
(SEQUENCE TYPE 1: STEADY BURN,
SEQUENCE TYPE 2: ROADRUNNER)
STEADY-BURN DRIVER TITLE 13 QUAD
(SEQUENCE TYPE 1: STEADY BURN,
SEQUENCE TYPE 2: TITLE 13 QUAD)
3 COLOR MODULE PATTERNS
# COLORS NUMBER NAME
3 1 QUINT
2 WARP
3 INTER-CYCLE
4 DOUBLE
5 QUAD
6 POWER PULSE
7 ROAD RUNNER
8 Q-SWITCH
STEADY-BURN DRIVER ROADRUNNER
9
10
11 QUAD 2
12 DOUBLE 2
2 13 QUINT
14 WARP
15 INTER-CYCLE
16 DOUBLE
17 QUAD
18 POWER PULSE
19 ROAD RUNNER
20 Q-SWITCH
21
22
23 QUAD 2
24 DOUBLE 2
(SEQUENCE TYPE 1: STEADY BURN,
SEQUENCE TYPE 2: ROADRUNNER)
STEADY-BURN DRIVER TITLE 13 QUAD
(SEQUENCE TYPE 1: STEADY BURN,
SEQUENCE TYPE 2: TITLE 13 QUAD)
STEADY-BURN DRIVER ROADRUNNER
(SEQUENCE TYPE 1: STEADY BURN,
SEQUENCE TYPE 2: ROADRUNNER)
STEADY-BURN DRIVER TITLE 13 QUAD
(SEQUENCE TYPE 1: STEADY BURN,
SEQUENCE TYPE 2: TITLE 13 QUAD)
ENFSLXSS 7.12
Loading...