SAE CLASS 1 RECESS MOUNT
ENFSRSxx - RECESS MOUNT BLACK GROMMET
ENFSLSRFxx - RECESS MOUNT
RECESS MOUNT VERSION
LIGHT ASSEMBLY
TECHNICAL SPECIFICATIONS
RECESS MOUNT NEXUS
Single Mount
Dimensions:
Input Voltage: 10 - 16 Vdc or 10 - 30 Vdc*
CURRENT CONSUMPTION
6, 12 Split &
18 Tri-Color
<1.0A @12.8 Vdc <0.6A @ 25.6 Vdc
9 LED Single Color <1.5A @ 12.8 Vdc <0.9A @ 25.6 Vdc
12 LED Single Color <2.0A @12.8 Vdc <1.2A @ 25.6 Vdc
GASKET
5.25”L x 2.25”H x 1.50”D
(See Pg. 2 for Installation Template)
10-16 Vdc 10-30 Vdc *
* - Special Order
BACK VIEW OF RECESS MOUNT SHOWN
INSTALLATION:
RECESS MOUNT
1) Establish a position on the vehicle.
Use the cutout template (provided)
on second page and cut hole. Insert
Grommet into cutout first, then press
light assembly into grommet.
INFORMATION FOR NEXUS
SECONDARY:
WIRE HOOK-UP TABLE
WIRE COLOR: FUNCTION:
RED Power
BLACK Ground
**GREEN Sync2 *
WHITE to Ground Pattern Select/
Setup
WHITE to Power
Secondary Fuction
-see page 2-
DO NOT DAMAGE, BLOCK OR
TOUCH THE BREATHER PATCHES
Important Information:
• Warning devices are strictly regulated and governed by Federal, State and Municipal ordinances.
These devices shall be used ONLY on approved vehicles. It is the sole responsibility of the user of these
devices to ensure compliance.
• DO NOT connect this device to a strobe power supply. This product is self-contained and does not
require an external power supply.
Warning devices are strictly regulated and governed by Federal, State and Municipal ordinances. These devices shall be used ONLY on approved vehicles. It is the sole responsibility of the user of these devices to ensure compliance.
To review our Limited Warranty Statement & Return Policy for this or any SoundOff Signal product, visit our website at www.soundoffsignal.com/sales-support.
1.800.338.7337 / www.soundoffsignal.com
1.
If you have questions regarding this product, contact Technical Services, Monday - Friday, 8 a.m. to 5 p.m. at 1.800338.7337 (press #4 to skip the automated message).
SUPERIOR CUSTOMER RELATIONSHIPS. SMARTLY DESIGNED LIGHTING & ELECTRONIC SOLUTIONS.
Questions or comments that do not require immediate attention may be emailed to techservices@soundoffsigal.com.
IMPORTANT INFORMATION:
** To sync multiple NForce™
lights, connect the Green wires
from each light together.
* Will NOT work w/ other sync
products such as Ghost, LED3,
& Intercector.
GREEN
WHITE
+Vdc
A FUSE
5
RED
BLACK
ENFSRS1(x) 03.14
SLAVE MODE
The NFORCE™ is capable of being activated through the use of a user
supplied flasher by putting it in Slave Mode.
1. Permanently connect the NFORCE™ WHITE and BLACK wire to a good,
convenient ground.
2. Connect the NFORCE™ RED wire, through a 5amp fuse, to the output of
a +10-16Vdc switching flasher.
AFTER POWER IS ON, touching the WHITE wire to the ground
will allow you to change various setting on the module.
PATTERN SELECT & SYNC
CONFIGURATION INSTRUCTIONS
Connecting the WHITE wire to power will allow you to use
the secondary function on your Nexus Secondary Light.
SECONDARY FUNCTION:
• 1-color module = Cruise Mode (10% brightness, nonflashing)
• 2 - color modules = Separate Color Control (see Setup
Table) or Takedown (100% steady-burn of the 2nd color)
• 3 - color modules = Takedown (100% steady-burn of the
3rd color)
SETUP TABLE
SECONDS USER INTERFACE
FROM TO VISUAL FEEDBACK ACTION TAKEN
0 1 STEADY-HIGH (60%) FORWARD ONE PATTERN
1 2 STEADY-LOW (30%) BACKWARD ONE PATTERN
2 3 OFF COLOR SWAP (OFF OR ON )
3 4 STEADY - HIGH (60%) SIMULTANEOUS OR ALTERNATE
4 5 STEADY - LOW (30%) SEPARATE COLOR CONTROL (OFF OR ON)
*
5 6 OFF
6 7 STEADY-HIGH (60%)
If held longer than 7 seconds, the light will go back to flashing the current
pattern and no action will be taken.
RESET TO PATTERN 1
FACTORY RESET (PATTERN 1, COLOR
SWAP: OFF, SEQUENCE TYPE:1)
SEPARATE COLOR CONTROL: OFF
SETUP LIGHTS:
Simultaneous or Alternate Function
•1 or 2. The modules will flash simultaneously if they are set
to the same number. The modules will have an alternate flash
if set to different numbers.
Color swap
• Off or On. 2-color and 3-color modules, it changes which
color flashes first.
Separate color control (2 color lights only)
•Allows manual switching of flashing color. When this fea-
ture is programmed on the On state: the light will jump to the
first pattern of the 1-color patterns, you will only be able to
choose 1-color patterns, and Color Swap will be programmed
to Off. To select a 2-color pattern, program this feature to the
Off state. *To turn of Seperate Color Control you
must do a factory reset.
4.72"
1.800.338.7337 / www.soundoffsignal.com
2.
RECESS MOUNT CUTOUT TEMPLATE
1.65"
R0.46"
ENFSRS1(x) 03.14
PATTERN LIST
1 COLOR MODULE PATTERNS
# COLORS NUMBER NAME
1 1 QUINT
2 WARP
3 INTER-CYCLE
4 DOUBLE
5 QUAD
6 POWER PULSE
7 ROAD RUNNER
8 Q-SWITCH
STEADY-BURN DRIVER ROADRUNNER
9
10
11 QUAD 2
12 DOUBLE 2
(SEQUENCE TYPE 1: STEADY BURN,
SEQUENCE TYPE 2: ROADRUNNER)
STEADY-BURN DRIVER TITLE 13 QUAD
(SEQUENCE TYPE 1: STEADY BURN,
SEQUENCE TYPE 2: TITLE 13 QUAD)
2 COLOR MODULE PATTERNS
# COLORS NUMBER NAME
2 1 QUINT
2 WARP
3 INTER-CYCLE
4 DOUBLE
5 QUAD
6 POWER PULSE
7 ROAD RUNNER
8 Q-SWITCH
STEADY-BURN DRIVER ROADRUNNER
9
10
11 QUAD 2
12 DOUBLE 2
1 13 QUINT
14 WARP
15 INTER-CYCLE
16 DOUBLE
17 QUAD
18 POWER PULSE
19 ROAD RUNNER
20 Q-SWITCH
21
22
23 QUAD 2
24 DOUBLE 2
(SEQUENCE TYPE 1: STEADY BURN,
SEQUENCE TYPE 2: ROADRUNNER)
STEADY-BURN DRIVER TITLE 13 QUAD
(SEQUENCE TYPE 1: STEADY BURN,
SEQUENCE TYPE 2: TITLE 13 QUAD)
STEADY-BURN DRIVER ROADRUNNER
(SEQUENCE TYPE 1: STEADY BURN,
SEQUENCE TYPE 2: ROADRUNNER)
STEADY-BURN DRIVER TITLE 13 QUAD
(SEQUENCE TYPE 1: STEADY BURN,
SEQUENCE TYPE 2: TITLE 13 QUAD)
3 COLOR MODULE PATTERNS
# COLORS NUMBER NAME
3 1 QUINT
2 WARP
3 INTER-CYCLE
4 DOUBLE
5 QUAD
6 POWER PULSE
7 ROAD RUNNER
8 Q-SWITCH
STEADY-BURN DRIVER ROADRUNNER
9
10
11 QUAD 2
12 DOUBLE 2
2 13 QUINT
14 WARP
15 INTER-CYCLE
16 DOUBLE
17 QUAD
18 POWER PULSE
19 ROAD RUNNER
20 Q-SWITCH
21
22
23 QUAD 2
24 DOUBLE 2
(SEQUENCE TYPE 1: STEADY BURN,
SEQUENCE TYPE 2: ROADRUNNER)
STEADY-BURN DRIVER TITLE 13 QUAD
(SEQUENCE TYPE 1: STEADY BURN,
SEQUENCE TYPE 2: TITLE 13 QUAD)
STEADY-BURN DRIVER ROADRUNNER
(SEQUENCE TYPE 1: STEADY BURN,
SEQUENCE TYPE 2: ROADRUNNER)
STEADY-BURN DRIVER TITLE 13 QUAD
(SEQUENCE TYPE 1: STEADY BURN,
SEQUENCE TYPE 2: TITLE 13 QUAD)
1.800.338.7337 / www.soundoffsignal.com
3.
ENFSRS1(x) 03.14
Loading...